EK01 Data Sheet - 2004-08-25 EK01 - ESM Starter Kit with Tualatin Pentium III u Computing module ESM EM02: - Tualatin ULP Pentium III / 933MHz or Celeron / 400MHz - 512MB SDRAM, CompactFlash slot - Graphics, Gigabit Ethernet, USB 1.1 (front) - COM, keyboard/mouse, (E)IDE, floppy (rear) u Carrier card EC01 (ATX-compatible format): - 1 ESM slot, 3 PCI slots - USB 2.0, COM, IDE, floppy connector u Accessories: - External PSU, PCI-104 adapter Embedded System Modules are complete computers on a controlled by an Ultra-Low Power Tualatin Pentium III module. A final ESM-based embedded application with 933MHz or an Ultra-Low Voltage Tualatin Celeron consists either of a stand-alone ESM (the power supply Processor with 400MHz. It provides 16KB L1 and connection being sufficient to operate the module), an 512KB/256KB L2 cache. The EM02 uses the Intel 815G ESM with an application-specific carrier card and/or chip set, including graphics. It provides one VGA an ESM with additionally plugged PCI-104 modules.connector, one USB 1.1 connector Type A and one The EK01 is a ready-to-use starter kit that allows Gigabit Ethernet interface at the front panel. It also evaluation of the functions of the EM02 Embedded provides 512MB of DRAM and a CompactFlash slot on System Module. The kit consists of the standard CPU board. As an alternative to onboard USB, legacy I/O is module, DRAM memory, the carrier card with I/O routed to the carrier board via the J2 system connectors, an external PSU, and an adapter for connector of the EM02. It includes a serial interface, mounting a PCI-104 module. The EK01 provides versatile (E)IDE, a floppy interface, as well as two PS/2 mounting options and can also be installed in a interfaces for keyboard and mouse. standard PC (including a PCI-104 module). The carrier board has an ATX-compatible format and After evaluation, the design overhead for each provides the mechanical platform, the power supply and application is limited to I/O. Depending on the the I/O connectors. It comes with one ESM slot and application and quantity it may be necessary to three PCI slots, which allow the use of standard develop a simple carrier card, choose PCI-based extension cards in the PC. It is equipped with USB 2.0 standard components, write software drivers for those (front), a 9-pin D-Sub for an RS232 serial interface additional functions, or design a housing. This (front) and connectors for IDE and floppy. The ESM minimal additional design effort can be carried out by carrier also features an I2C EEPROM for the board ID the user or by MEN.and revision information. The EM02 is an ideal computing platform for embedded DVI/TFT/video are not supported on the EK01 kit but industrial PCs under Windows or Linux. It is are available on the EM02 itself for implementation as a hub interface on other (custom) carrier cards. ® 1 Embedded Solutions EK01 Data Sheet - 2004-08-25 Technical Data EC01 ESM Carrier Card · EM02: 215g (incl. heat sink) • One ESM slot Environmental Specifications • J1 and J2 assembled • Temperature range (operation): • I/O connectors · 0..+60°C · USB 2.0 · Industrial temperature range on request · RS232 COM interface · Airflow: min. 10m³/h · IDE connector • Temperature range (storage): -40..+85°C · Floppy disk interface • Relative humidity (operation): max. 95% non-condensing · PS/2 keyboard/mouse connector, via SA adapter • Relative humidity (storage): max. 95% non-condensing • PCI interface • Altitude: -300m to + 3,000m · Three PCI slots • Shock: 15g/11ms · 33MHz, 32-bit data bus, 5V V-I/O • Bump: 10g/16ms • Reset button and power LED • Vibration (sinusoidal): 2g/10..150Hz EM02 ESM Module Safety • CPU: Celeron/400MHz or Pentium III/933MHz • PCB manufactured with a flammability rating of 94V-0 by • Graphics: VGA, connector at front panel UL recognized manufacturers • Memory · 256MB or 512MB SO-DIMM SDRAM installed EMC · CompactFlash interface • Tested according to EN 55022 (radio disturbance), • Interfaces IEC1000-4-2 (ESD) and IEC1000-4-4 (burst) with regard to · 10/100/1000Base-T PCI Ethernet, RJ45 at front panel CE conformity · USB 1.1, connector at front panel • Mass storage: Fast IDE ports for IDE devices (40-pin, via Software Support EC01) and CompactFlash • Phoenix BIOS • I/O Extension • Windows · Accessible on EC01 • Linux · Keyboard • QNX · Mouse • VxWorks · COM1 · Floppy • PCI Interface · 32-bit/33-MHz PCI interface at PCI-104 connector J1 · Support of one external master Accessories • External PSU • Adapter for mounting of one PCI-104 module Electrical Specifications • Supply voltage/power consumption: · EC01: +24V (12V..36V), 1.6A; +24V on pin 1, GND on pin 2 · EM02: +5V (4.85V..5.25V), 796mA (Celeron version) · EM02: +3.3V (3.2V..3.4V), 794mA (Celeron version) • MTBF EM02: 165,000h @ 50°C Mechanical Specifications • Dimensions of EC01 PCB: 170mm x 150mm • EM02 conforming to ESM specification (PCB: 149mm x 71mm) • Weight · EC01: 200g (without floppy drive) ® 2 Embedded Solutions EK01 Data Sheet - 2004-08-25 Diagram ® 3 Embedded Solutions EK01 Data Sheet - 2004-08-25 Related Products Standard Hardware 08EK01-01 ESM evaluation kit: Mini ATX carrier board EC01 with 1 ESM slot, 3 PCI slots, floppy interface; ESM EM02 with ULP Pentium III / 933MHz, graphics, Gigabit Ethernet, USB; temperature range: 0..+60°C; incl. external PSU and adapter for mounting of one PCI-104 module - 512MB DRAM installed, CompactFlash not installed (08EK01-01 = EC01-03 + EM02-04) 08EK01-02 ESM evaluation kit: Mini ATX carrier board EC01 with 1 ESM slot, 3 PCI slots, floppy interface; ESM EM02 with ULV Pentium III Celeron/ 400MHz, graphics, Gigabit Ethernet, USB; temperature range: 0..+60°C; incl. external PSU and adapter for mounting of one PCI-104 module - 512MB DRAM installed, CompactFlash not installed (08EK01-02 = EC01-03 + EM02-07) 08EK01-03 ESM evaluation kit: Mini ATX carrier board EC01 with 1 ESM slot, 3 PCI slots, floppy interface; ESM EM02 with ULV Celeron 650MHz, graphics, Gigabit Ethernet, USB; temperature range: 0..+60°C; incl. external PSU and adapter for mounting of one PCI-104 module - 512MB DRAM installed, CompactFlash not installed (08EK01-03 = EC01-03 + EM02-09) 15EM02-04 EM02, ESM - Embedded System Module, ULP Pentium III / 933MHz, CompactFlash slot, 512MB DRAM installed, graphics, Gigabit Ethernet, USB; PCI-104 stackable; temperature range: 0..+60°C 15EM02-07 EM02 for ESM Kit EK01-02, ESM - Embedded System Module, ULV Celeron / 400MHz, CompactFlash slot, 512MB DRAM installed, graphics, Gigabit Ethernet, USB;temperature range: 0..+60°C 15EM02-09 EM02 for ESM Kit EK01-03, ESM - Embedded System Module, ULV Celeron / 650MHz, CompactFlash slot, 512MB DRAM installed, graphics, Gigabit Ethernet, USB; temperature range: 0..+60°C Please refer to our ESM - Embedded System Modules compare chart for a selection of further single-board computers with different processors and on-board functionality. Accessories 0751-0006 CompactFlash card, 512MB, Type I, 0..+60°C 0751-0008 CompactFlash card, 64MB, Type I, 0..+60°C 0751-0009 CompactFlash card, 128MB, Type I, 0..+60°C 0751-0012 CompactFlash card, 256MB, Type I, 0..+60°C 0751-0018 CompactFlash card, 256MB, Type I, -40..+85°C 0752-0096 512MB DRAM 0..+60°C for 15EM02-04 (08EK01-01) 0752-0156 512MB DRAM 0..+60°C for 15EM02-07 (08EK01-02) ® 4 Embedded Solutions EK01 Data Sheet - 2004-08-25 Related Products 0752-0166 512MB DRAM 0..+60°Cfor 15EM02-09 (08EK01-03) For more functions realized with SA adapters, see the listing on MEN's website. You can also view our SA adapter compare chart for a quick overview of different functions. Please contact sales to make sure that these SA adapters can be used in the board configuration you are looking for. Software This MEN board is designed to work in a Microsoft Windows environment. For additional Windows driver packages provided or recommended by MEN please refer to the ordering numbers below. QNX software for this MEN board is available from QNX (www.qnx.com). For QNX BSP and driver support provided by MEN please refer to the ordering numbers below. VxWorks software for this MEN board is available from WindRiver Systems. For VxWorks BSP and driver support provided by MEN please refer to the ordering numbers below. This board is an MEN product running Linux. For Linux BSP and driver support provided by MEN please refer to the ordering numbers below. 13EM02-70 Windows 2000/XP graphics driver (Intel graphics driver for 815 chipset) for A13, EM02 (ESM kit EK01) 13EM02-71 Windows 2000/XP network driver (Intel) for A13 and EM02 (ESM kit EK01) - only for 933MHz versions! Documentation 20ABMX-00 Phoenix BIOS user manual 20EK01-00 EK01 user manual, includes EM02 user manual (20EM02-00) For the most up-to-date ordering information and direct links to other data sheets and downloads, see the EK01 online data sheet under www.men.de. --> Click here! ® 5 Embedded Solutions EK01 Data Sheet - 2004-08-25 Contact Information Germany France UK USA MEN Mikro Elektronik GmbHMEN Mikro Elektronik SAMEN Micro LtdMEN Micro, Inc. Neuwieder Straße 5-718, rue René CassinWhitehall, 75 School LanePO Box 4160 90411 NurembergZA de la ChâtelaineHartford, NorthwichLago Vista, TX 78645-4160 Phone +49-911-99 33 5-074240 GaillardCheshire UK, CW8 1PFPhone (512) 267-8883 Fax +49-911-99 33 5-901Phone +33 (0) 450-955-312Phone +44 (0) 1477-549-185Fax (512) 267-8803 E-mail info@men.deFax +33 (0) 450-955-211Fax +44 (0) 1477-549-178E-mail sales@menmicro.com www.men.deE-mail info@men-france.frE-mail info@menmicro.co.ukwww.menmicro.com www.men-france.frwww.menmicro.co.uk The date of issue stated in this data sheet refers to the Technical Data only. Changes in ordering information given herein do not affect the date of issue. All brand or product names are trademarks or registered trademarks of their respective holders. Information in this document has been carefully checked and is believed to be accurate as of the date of publication; however, no responsibility is assumed for inaccuracies. MEN Mikro Elektronik accepts no liability for consequential or incidental damages arising from the use of its products and reserves the right to make changes on the products herein without notice to improve reliability, function or design. MEN Mikro Elektronik does not assume any liability arising out of the application or use of the products described in this document. The products of MEN Mikro Elektronik are not suited for use in nuclear reactors and for application in medical appliances used for therapeutical purposes. Application of MEN's products in such plants is only possible after the user has precisely specified the operation environment and after MEN Mikro Elektronik has consequently adapted and released the product. Copyright © 2004 MEN Mikro Elektronik GmbH. All rights reserved. ® Embedded Solutions