Visual UpTime Select ASE model 807-0202 OC-3c/STM-1 i nline probe ASE Single mode with LinkSafe capabilities The Visual UpTime® Select™ OC-3c/STM-1 LinkSafe™ The OC-3c/STM-1 inline probe ASE is designed Key features inline probe ASE supports single mode ATM OC-3c for deployment at the network demarcation point  Inband management capabilities physical lines, with SONET and SDH standards, at between a subscriber’s CPE and the WAN. It can be speeds up to 155 Mbps. This ASE supports Multi-Proto- deployed in ATM and mixed frame relay-ATM environ-  LinkSafe technology col software for deployment in standard ATM networks ments. The fi gure below shows the ASE positioned  Multi-Protocol or IP Transport software and IP Transport software for deployment in ATM-based at the edge of an inter-worked frame relay-to-ATM  Service Level Agreement (SLA) metrics networks that use IP switching. The ASE also includes network, allowing for SLA messaging between a frame  Application analysis capability LinkSafe technology to protect circuit integrity in case relay DLCI and an ATM VPI/VCI.  LAN management port of an ASE outage, as well as power failure notifi cation.  Realtime events OC-3c inline probe model 202 front view OC-3c inline probe model 202 rear view LAN Branch ASEs Visual Frame to ATM UpTime Interworking CPE OC-3c Select T1 ATM ASE Router server Frame ATM Network Network OC-3c inline probe model 202 on ATM/Frame network Technical Data What are ASEs? OC-3c inline probe ASE specifcations ASEs (Analysis Service Elements) are data General Dimensions 1 EIA unit (1.75”) high x 19” wide rack-mountable chassis collection and network performance monitor- Weight 10 lbs. ing hardware devices placed on a wide area Data Rate to 155 Mbps synchronous network (WAN) or Local Area Network (LAN) Timing Mode Derived externally from the network. as part of the Visual UpTime Select system, o o o o Environment Operating Temperature 0 to +40 C (+32 to +104 F) which offers in-depth, real-time, and historical o o o o Storage Temperature -20 to +55 C (-4 to +131 F) visibility into the performance of your Clearance Requirement Minimum of 3” (7.62 cm) space on sides. applications infrastructure. In the system, Operating/Storage Humidity 10% to 90% non-condensing data gathered by ASEs is stored in the Visual Power Requirements Input 100 to 240 VAC UpTime Select server and displayed and ana- Frequency 50/60 Hz lyzed from the Visual UpTime Select Web client. Input Current Rating 0.5 amps As a service level management tool, ASEs Bypass 5 volt 1 amp DC indicate when services are being met, provide Network Interface Line Rate 155.52 Mbps warnings when services start to degrade, and Line Mode SONET or SDH send alerts when services are not met. Cell Delineation HEC Cell Scrambler Enable or Disable Hardware Warranties Connectors 2 Sff Duplex-LC, Network Tx and Rx, CPE Tx and Rx Enhanced Gold, Bronze, and International Wavelength 1274 nm/1356 nm Gold ASE hardware warranty service programs Tx Average Output Power -11dBm (typical) Measured with single mode cable are available to help you maximize your Rx Sensitivity -33dBm (typical) investment in Visual UpTime Select. For more Serial Port Interface Baud Rate 57600, 19200, or 9600 bps Parity 8 data bits, no parity detailed warranty information, visit: Stop Bit 1 stop bit www.fl ukenetworks.com/visualcustomercare Electrical Format EIA RS-232, DTE Ordering Information Connector 9-pin D, male per EIA-574 For more details, please contact your Visual Ethernet 10/100BaseT Bite Rate 10 or 100 Mbps Interface UpTime Select authorized reseller or Connector 8-pin modular jack: RJ-48 Fluke Networks Sales at (800) 240-4010 Compliant with Bellcore GR-253 CORE and ITE G.957 standards or (301) 296-2300. NETWORK SUPER VISION Fluke Networks P.O. Box 777, Everett, WA USA 98206-0777 Fluke Networks operates in more than 50 countries worldwide. To fi nd your local offi ce contact details, go to www.ţ ukenetworks.com/contact. 2006 Fluke Corporation. All rights reserved. © Printed in U.S.A. 2/2006 2643526 D-ENG-N Rev A