Visual UpTime Select ASE model 807-0200 DS3 i nline probe ASE With LinkSafe capabilities The Visual UpTime® Select™ DS3 LinkSafe™ inline The DS3 inline probe ASE is designed for deploy- Key features probe ASE complies with Class A standards for ment at the network demarcation point between a  Inband management capabilities countries using DS3 ATM lines (U.S. and Canada) and subscriber’s CPE and the WAN. It can be deployed in supports digital transmission at the DS3 rate of 44 ATM and mixed frame relay-ATM environments. The  LinkSafe technology Mbps. This ASE supports Multi-Protocol software for fi gure below shows the ASE positioned at the edge of  Multi-Protocol or IP Transport software deployment in standard ATM networks and IP Trans- an inter-worked frame relay-to-ATM network, allowing  Service Level Agreement (SLA) metrics port software for deployment in ATM-based networks for SLA messaging between a frame relay DLCI and an  Application analysis capability that use IP switching. The ASE also includes LinkSafe ATM VPI/VCI.  LAN management port technology to protect circuit integrity in case of an  Realtime events ASE outage, as well as power failure notifi cation. DS3 inline probe model 200 front view DS3 inline probe model 200 rear view LAN Branch ASEs Visual Frame to ATM UpTime Interworking CPE Select T1 ATM ASE Router server Frame ATM Network Network DS3 inline probe model 200 on ATM/Frame network Technical Data What are ASEs? DS3 inline probe ASE specifcations ASEs (Analysis Service Elements) are data General Dimensions 1 EIA unit (1.75”) high x 19” wide rack-mountable chassis collection and network performance monitor- Weight 10 lbs. ing hardware devices placed on a wide area Data Rate to 45 Mbps synchronous network (WAN) or Local Area Network (LAN) Timing Mode Derived externally from the network. as part of the Visual UpTime Select system, o o o o Environment Operating Temperature 0 to +40 C (+32 to +104 F) which offers in-depth, real-time, and historical o o o o Storage Temperature -20 to +55 C (-4 to +131 F) visibility into the performance of your Clearance Requirement Minimum of 3” (7.62 cm) space on sides. applications infrastructure. In the system, Operating/Storage Humidity 10% to 90% non-condensing data gathered by ASEs is stored in the Visual Power Requirements Input 100 to 240 VAC UpTime Select server and displayed and ana- Frequency 50/60 Hz lyzed from the Visual UpTime Select Web client. Input Current Rating 0.5 amps As a service level management tool, ASEs Network Interface Line Rate 44.736 Mbps indicate when services are being met, provide Cell Delineation HEC or PLCP warnings when services start to degrade, and Cell Scrambler Enable or Disable send alerts when services are not met. Line Build Out Long = more than 225 feet. Short = 225 feet or less. Connector 4 BNC (75 ohm), Network Tx and Rx, CPE Tx and Rx Hardware Warranties Serial Port Interface Baud Rate 57600, 19200, or 9600 bps Enhanced Gold, Bronze, and International Parity 8 data bits, no parity Gold ASE hardware warranty service programs Stop Bit 1 stop bit are available to help you maximize your Electrical Format EIA RS-232, DTE investment in Visual UpTime Select. For more Connector 9-pin D, male per EIA-574 Ethernet 10/100BaseT Bite Rate 10 or 100 Mbps detailed warranty information, visit: Interface www.fl ukenetworks.com/visualcustomercare Connector 8-pin modular jack: RJ-48 Ordering Information For more details, please contact your Visual UpTime Select authorized reseller or Fluke Networks Sales at (800) 240-4010 or (301) 296-2300. NETWORK SUPER VISION Fluke Networks P.O. Box 777, Everett, WA USA 98206-0777 Fluke Networks operates in more than 50 countries worldwide. To fi nd your local offi ce contact details, go to www.ţ ukenetworks.com/contact. 2006 Fluke Corporation. All rights reserved. © Printed in U.S.A. 2/2006 2643490 D-ENG-N Rev A