MVME5100 Series VMEbus Processor Module Front page The Emerson Network Power MVME5100 series is the flagship of the Emerson The MVME5100 is designed PowerPlus II VME Architecture line, enabling supercomputing levels of performance to meet the needs of OEMs in a single VMEbus slot. Based on an integrated PCI bridge-memory controller servicing the defense and ASIC designed by Emerson, PowerPlus II takes memory performance to new levels aerospace, industrial with 582MB/s memory read bandwidth and 640MB/s burst write bandwidth. automation and medical Interior page market segments The MVME5100 series utilizes the PowerPlus II Architecture to support full PCI throughput of 264MB/s without starving the processor from its memory. The MVME5100 is designed to meet the needs of OEMs servicing the defense and ° MPC7410 or MPC750 microprocessor with aerospace, industrial automation and medical market segments. 32KB/32KB L1 cache ° Up to 2MB of secondary backside cache ° 100 MHz frontside bus ° Up to 512MB of on-board ECC SDRAM – expandable up to 1GB with optional RAM500 memory expansion modules ° 17MB flash memory ° Dual IEEE P1386.1 compatible 32/64-bit PMC expansion slots ° 64-bit PCI expansion mezzanine connector allowing up to four more PMCs ° Dual 16550 compatible async serial ports ° Dual 10BaseT/100BaseTX Ethernet ° 32KB NVRAM and time-of-day clock with replaceable battery backup ° Four 32-bit timers and one watchdog timer ° On-board debug monitor ° Single VME slot even when fully configured with two PMC modules and both add-on memory mezzanines Rows A & C 64 pins Rows D & Z 64 pins Front page Interior page MVME5100 Block Diagram SDRAM Expansion L2 Cache 256MB 1 or 2MB SDRAM Expansion Flash Serial Serial 64 or 256MB 1MB 16550 Processor 60x MPC7410 Arbiter MPC750 ECC SDRAM Flash Serial RJ-45 Up to 512MB 16MB 16550 Vcore REG Hawk ASIC BUF 100 MHz Memory Bus X-Bus +3.3V RTC REG NVRAM 64-bit/33 MHz Local PCI Bus Ethernet 82559ER FP I/O FP I/O PCI VME Ethernet RJ-45 PMC2 PMC1 Expansion Universe II 82559ER RJ-45 P2 P1 In IPMC mode, the MVME5100 supports legacy Overview MVME761 or MVME712M I/O modules (with limited I/O COMPaTIbIlITy PMC I/O) when an IPMC761 or IPMC712 PMC card is Historically, Emerson has offered two tracks in its populated in PMC slot 1. In this configuration, PMC ® PowerPC Architecture VME portfolio. The first track slot 2 contains some signals that are reserved for (which includes the MVME2600/2700) provides extended SCSI. typical single-board computer I/O features including Ethernet, SCSI, multiple serial ports, a parallel port IPMC MOdulES and a single PMC slot. The on-board I/O is routed to P2 The IPMC761 and IPMC712 are optional add-on PMC and made available to the user via Emerson MVME761 modules that provide backward compatibility with or MVME712M transition boards. The second track previous-generation Emerson products (such as (which includes the MVME2300/2400) offers limited MVME2600 and MVME2700) using the MVME761 or on-board I/O (Ethernet and a single serial port both via MVME712M transition board. IPMC modules provide the front panel) but provides dual PMC slots enabling rear I/O support for the following: maximum user I/O customization. ° One single-ended Ultra Wide SCSI port ° One parallel port The MVME5100 merges the best features of both tracks enabling the OEM to support varying I/O ° Four serial ports (2 or 3 async and 1 or 2 sync/async, depending on module) requirements with the same base platform, simplify- ing part number maintenance, technical expertise With this PMC card configuration, the memory requirements and sparing. mezzanine, one PMC slot and the PMCspan are still P2 I/O MOdES available, providing support for OEM product The MVME5100 supports two, jumper-configurable customization. P2 I/O modes; PMC and IPMC. PMC mode is backward compatible with the MVME2300/MVME2400. In PMC mode, 64 pins from PMC slot 1 and 46 pins from PMC slot 2 are available onP2 for PMC rear I/O. 2 Front page Interior page PMC P11 & P12 Software Support PCI FIrMwarE MOnITOr Firmware must fulfill the traditional functions of test PIB WB-554 and initialization and provide operating system boot ISA support. The MVME5100 firmware monitor exceeds these requirements with a proven monitor from the SCSI Super I/O ESCC CIO embedded VME leader. It expands features like power- LSI National 85230 8536 up tests with extensive diagnostics, as well as a powerful evaluation and debug tool for simple P2 MUX checkout or when high-level development debuggers PAL (IPMC761) require additional support. All this is included with the MVME5100 firmware; plus it supports booting both operating systems and kernels. OPEraTIng SySTEMS and KErnElS PMC P14 & P15 MVME5100 supports booting a variety of operating systems, including VxWorks from Wind River TranSITIOn MOdulES Systems, Inc., Integrity from Green Hills, and Linux The MVME761 transition module provides industry- from a variety of partners. standard connector access to the IEEE 1284 parallel port, a 10BaseT or 100BaseT port via an RJ-45 Specifications connector, two DB-9 connectors providing access to PrOCESSOr the asynchronous serial ports configured as EIA-574 MPC7410 MPC750 DTE and two HD-26 connectors providing access to the sync/async serial ports. These serial ports, labeled Clock 400/500 MHz 450 MHz Frequency: as Serial 3 and Serial 4 on the faceplate of the MVME761, are individually user-configurable as On-chip Cache 32K/32K 450 MHz (I/D): EIA-232, DCE or DTE via the installation of Emerson Serial Interface Modules (SIMs). A P2 adapter board On-chip Cache 32K/32K 32K/32K (I/D): provides interface signals to the MVME761 transition module. Two separate P2 adapter boards are available: Secondary 2MB 1MB Cache: one for 3-row backplanes and one for 5-row back- planes. The 3-row P2 adapter board provides connec- MaIn MEMOry tion for 8-bit SCSI. A 5-row P2 adapter board supports 16-bit SCSI and PMC I/O. ° Type: PC100 ECC SDRAM with 100 MHz bus ° Capacity: Up to 512MB on-board, expandable to The MVME712M transition module provides industry- 1GB with RAM500 memory mezzanines standard connector access to the Centronics parallel ° Single Cycle Accesses: 10 Read/5 Write port, a narrow SCSI port, and four DB-25 connectors ° Read Burst Mode: 7-1-1-1 idle; 2-1-1-1 aligned providing access to the asynchronous/synchronous page hit serial ports jumper configurable as EIA-232 DCE or ° Write Burst Mode: 4-1-1-1 idle; 2-1-1-1 aligned DTE. A P2 adapter board provides interface signals to page hit the MVME712M transition module. The 3-row P2 ° Architecture: 64-bit, single interleave adapter board also provides connection for 8-bit SCSI. To gain access to the additional user-definable I/O pins FlaSh MEMOry provided via the 5-row VME64 extension connector, a ° Type: EEPROM, on-board programmable special P2 adapter board is available. This adapter ° Capacity: 1MB via two 32-pin PLCC/CLCC sockets; panel replaces the traditional 3-row P2 adapter board 16MB surface mount and extends its capability by providing access to the PMC I/O pins. ° Read Access (16MB port): 70 clocks (32-byte burst) ° Read Access (1MB port): 262 clocks (32-byte burst) 3 16-bit SCSI COM1 COM2 Parallel SER3 Sync (761) Async (712) SER4 (Sync) P2 MUX Front page Interior page nVraM PCI ExPanSIOn COnnECTOr ° Capacity: 32KB (4KB available for users) ° Address/Data: A32/D32/D64 ° Cell Storage Life: 50 years at 55° C ° PCI Bus Clock: 33 MHz ° Cell Capacity Life: 5 years at 100% duty cycle, 25° C ° Signaling: 5V ° Removable Battery: Yes ° Connector: 114-pin connector located on the planar of the MVME5100 VMEbuS anSI/VITa 1-1994 VME64 (IEEE STd 1014) POwEr rEquIrEMEnTS (not including power required by PMC or IMPC ° Controller: Tundra Universe modules) ° DTB Master: A16–A32; D08–D64, BLT +5 V ± 5% +12 V ± 10% –12 V ± 10% ° DTB Slave: A24–A32; D08–D64, BLT, UAT MVME5100 3.0 A typ. 8.0 mA typ. 2.0 mA ° Arbiter: RR/PRI ° Interrupt Handler/Generator: IRQ 1–7/Any one of bOard SIzE seven IRQs ° Height: 233.4 mm (9.2 in.) ° System Controller: Yes, jumperable or auto detect ° Depth: 160.0 mm (6.3 in.) ° Location Monitor: Two, LMA32 ° Front Panel Height: 261.8 mm (10.3 in.) COunTErS/TIMErS ° Width: 19.8 mm (0.8 in.) ° TOD Clock Device: M48T37V ° Max. Component Height: 14.8 mm (0.58 in.) ° Real-Time Timers/Counters: Four, 32-bit programmable IPMC Modules ° Watchdog Timer: Time-out generates reset PMC InTErFaCE ° Address/Data: A32/D32/D64, PMC PN1, PN2, PN3, EThErnET InTErFaCE PN4 connectors ® ° Controller: Two Intel 82559ER ° PCI Bus Clock: 33 MHz ° Interface Speed: 10/100Mbps ° Signaling: 5V ° PCI Local bus DMA: Yes, with PCI burst ° Module Type: Basic, single-wide; P2 I/O ° Connector: One routed to front panel RJ-45, one routed to front panel RJ-45 or optionally routed to SCSI buS P2, RJ-45 on MVME761 ° Controller: Symbios 53C895A ° PCI Local Bus DMA: Yes, with PCI local bus burst aSynChrOnOuS SErIal POrTS ° Asynchronous (8-bit mode): 5.0MB/s ° Controller: 16C550C UART ° Ultra SCSI: 20.0MB/s (8-bit mode), 40.0MB/s (16- ° Number of Ports: Two, 16550 compatible bit mode) ° Configuration: RS-232 DTE/DCE ° Note: 16-bit SCSI operation precludes the use of ° Async Baud Rate, bps max.: 38.4K EIA-232, some PMC slot 2 signals. 115Kbps raw ° Connector: One routed to front panel RJ-45, one SynChrOnOuS SErIal POrTS on planar for development use ° Controller: 85230/8536 ° Number of Ports: Two (IPMC761); one (IPMC712) dual IEEE P1386.1 PCI MEzzanInE Card SlOTS ° Configuration: IPMC761: TTL to P2 (both ports), ° Address/Data: A32/D32/D64, PMC PN1, PN2, PN3, SIM configurable on MVME761; IPMC712: EIA-232 PN4 connectors to P2 ° PCI Bus Clock: 33 MHz ° Baud Rate, bps max.: 2.5M sync, 38.4K async ° Signaling: 5V ° Oscillator Clock Rate (PCLK): 10 MHz/5 MHz ° Power: +3.3V, +5V, ±12V; 7.5 watts maximum per PMC slot ° Module Types: Two single-wide or one double- wide, front panel or P2 I/O 4 Front page Interior page aSynChrOnOuS SErIal POrTS POwEr rEquIrEMEnTS (Additional power load placed on MVME5100 series ° Controller: 16C550 UART; 85230/8536 with IPMC installed) ° Number of Ports: Two (IPMC761); three (IPMC712) ° Configuration: EIA-574 DTE (IPMC761); EIA-232 +5V ± 5% +12V ± 10% –12V ± 10% (IPMC712) MVME5100: 3.8 A max. 8.0 mA typ. 2.0 mA typ. ° Async Baud Rate, bps max.: 38.4K EIA-232, 3.0 A typ. 115Kbps raw MVME5110- 3.8 A max. 8.0 mA typ. 2.0 mA typ. 21xx: 3.1 A typ. ParallEl POrT MVME5110- 4.7 A max. 8.0 mA typ. 2.0 mA typ. ° Controller: PC97307 22xx: 3.5 A typ. ° Configuration: 8-bit bi-directional, full IEEE 1284 support; Centronics compatible (minus EPP and ECP on MVME712M) ° Modes: Master only Transition Modules I/O COnnECTOrS MVME761 MVME712M Asynchronous Serial Ports: Two, DB-9 labeled as COM1 Three, DB-25 labeled Serial 1, Serial 2 and COM2 and Serial 3 Synchronous Serial Ports: Two, HD-26 labeled as Serial 3 One, DB-25 labeled as Serial 4 and Serial 4 (user-configurable via installation of SIMs); two 60-pin connectors on MVME761 planar for installation of two SIMs Parallel Port: HD-36, Centronics compatible D-36, Centronics compatible Ethernet: 10BaseT or 100BaseTX, RJ-45 Not available SCSI: 8- or 16-bit, 50- or 68-pin connector 8-bit, standard SCSI D-50 via P2 adapter 5 Front page Interior page All Modules EnVIrOnMEnTal (Minimum of 400 LFM of forced air cooling is recommended for operation in the higher temperature ranges.) Operating Non-operating Temperature: 0° C to +55° C –40° C to +85° C (inlet air temp. with forced air cooling*) Humidity (NC): 5% to 90% 5% to 90% Vibration: 2 Gs RMS, 6 Gs RMS, 20–2000 Hz 20–2000 Hz random random ElECTrOMagnETIC COMPaTIbIlITy (EMC) ° Intended for use in systems meeting the following regulations: Å U.S.: FCC Part 15, Subpart B, Class A (non-residential) Å Canada: ICES-003, Class A (non-residential) ° This product was tested in a representative system to the following standards: Å CE Mark per European EMC Directive 89/336/EEC with Amendments; Emissions: EN55022 Class B; Immunity: EN55024 SaFETy All printed wiring boards (PWBs) are manufactured with a flammability rating of 94V-0 by UL recognized manufacturers. dEMOnSTraTEd MTbF (based on a sample of eight boards in accelerated stress environment) ° Mean: 190,509 hours ° 95% Confidence: 107,681 hours 6 Front page Interior page Ordering Information All models of the MVME51xx are available with either VME Scanbe front panel (-xxx1) or IEEE 1101 compatible front panel (-xxx3). Part Number Description MVME51005E-0161 512MB ECC SDRAM, 17MB flash and 1MB L2 cache Scanbe 5E MVME51005E-0163 512MB ECC SDRAM, 17MB flash and 1MB L2 cache IEEE 5E 400/500 Mhz MPC7410 Commercial Models MVME51105E-2161 400 MHz MPC7410, 512MB ECC SDRAM, 17MB flash and 2MB L2 cache Scanbe 5E MVME51105E-2163 400 MHz MPC7410, 512MB ECC SDRAM, 17MB flash and 2MB L2 cache IEEE 5E MVME51105E-2261 500 MHz MPC7410, 512MB ECC SDRAM, 17MB flash and 2MB L2 cache Scanbe 5E MVME51105E-2263 500 MHz MPC7410, 512MB ECC SDRAM, 17MB flash and 2MB L2 cache IEEE 5E MVME712M Compatible I/O IMPC7126E-002 Multifunction rear I/O PMC module; 8-bit SCSI, Ultra Wide SCSI, one parallel port, three async and one sync/async serial ports MVME712M6E Transition module connectors: One DB-25 sync/async serial port, three DB-25 async serial port, one AUI connector, one D-36 parallel port, and one 50-pin 8-bit SCSI; includes 3-row DIN P2 adapter module and cable MVME761 Compatible I/O IPMC7616E-002 Multifunction rear I/O PMC module; 8-bit SCSI, one parallel port, two async and two sync/async serial ports MVME7616E-001 Transition module: Two DB-9 async serial port connectors, two HD-26 sync/async serial port connectors, one HD-36 parallel port connector, one RJ-45 10/100 Ethernet connector; includes 3-row DIN P2 adapter module and cable (for 8-bit SCSI) MVME7616E-011 Transition module: Two DB-9 async serial port connectors, two HD-26 sync/async serial port connectors, one HD-36 parallel port connector, and one RJ-45 10/100 Ethernet connector; includes 5-row DIN P2 adapter module and cable (for 16-bit SCSI); requires backplane with 5- row DIN connectors SIM232DCE5E EIA-232 DCE Serial Interface Module 5E SIM232DTE5E EIA-232 DTE Serial Interface Module 5E related Products PMCSPAN26E-002 Primary PMC expansion for MVME5100/5110/5500 w/IEEE handles, 6E PMCSPAN26E-010 Secondary PMC expansion for PMCSPAN26E-002 w/IEEE handles, 6E RAM5005E-006 Stackable (top) 256MB ECC SDRAM mezzanine 5E RAM5005E-016 Stackable (bottom) 256MB ECC SDRAM mezzanine 5E documentation V5100A/IH MVME5100 Installation and Use V5100A/PG Programmer’s Reference Guide VME761A/IH MVME761 Transition Module Installation and Use VME712MA/IH MVME712 Transition Module Installation and Use PPCBUGA1/UM PPCBug Firmware Package User’s Manual (volumes one and two) PPCBUGA2/UM PPCDIAA/UM PPCBug Diagnostics Manual 7 Front page Interior page SOluTIOn SErVICES Emerson Network Power provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh. Plus solution extras include enhanced warranty and repairs. PowerPC is a trademark of IBM Corp. and used under license. Intel is a registered trademark of Intel Corporation or its subsidiaries in the U.S. and other countries. All other product or service names are the property of their respective owners. This document identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Emerson Network Power may sell products. A prospective buyer should exercise its own independent judgment to confirm the suitability of the products for particular applications. Emerson Network Power reserves the right to make changes, without notice, to any products or information herein which will, in its sole discretion, improve reliability, function, or design. Emerson Network Power does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Emerson Network Power’s licensee, licensee’s transferees, and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations. AC Power Systems Embedded Power Precision Cooling Emerson Network Power. Connectivity Integrated Cabinet Solutions Services The global leader in enabling DC Power Systems Outside Plant Site Monitoring ™ Business-Critical Continuity . Embedded Computing Power Switching & Control Surge & Signal Protection Business-Critical Continuity, Emerson Network Power and Emerson Network Power the Emerson Network Power logo are trademarks and Sales Offices: Tempe, AZ U.S.A. 1 800 759 1107 or +1 602 438 5720, Shanghai, China +86 215292 5693 service marks of Emerson Electric Co. Paris, France +33 1 69 35 77 00 , Tokyo, Japan +81 3 5424 3101, Munich, Germany +49 (0) 89 9 608 2 333 ©2008 Emerson Electric Co. Hong Kong, China +852 2966 3210, Tel Aviv, Israel +972 3 568 4387 EmersonNetworkPower.com/embeddedcomputing MVME5100-D18 1/08