WINBOND W83977EG-AW
Specifications
Interface
Parallel/Serial
Lead Free Status
Lead Free
OnNow Funtions
Keyboard Wake-Up by programmable keys
Package / Case
128-BFQFP
Packaging
Tray
RoHS Status
RoHS Compliant
UART
Two high-speed 16550 compatible UARTs with 16-byte send/receive FIFOs
Voltage - Supply
5V
Datasheet
Extracted Text
W83977EF-AW /W83977EG-AW
NUVOTON
ISA I/O
W83977EF-AW
W83977EG-AW
Publication Release Date: January, 2010
-I - Revision 1.5
W83977EF-AW /W83977EG-AW
TABLES OF CONTENTS
1. GENERAL DESCRIPTION.............................................................................................................................1
2. FEATURES .......................................................................................................................................................2
3. PIN CONFIGURATION ...................................................................................................................................5
4. PIN DESCRIPTION.........................................................................................................................................6
4.1 HOST INTERFACE ..........................................................................................................................................6
4.2 GENERAL PURPOSE I/O PORT......................................................................................................................8
4.3 SERIAL PORT INTERFACE..............................................................................................................................9
4.4 INFRARED INTERFACE .................................................................................................................................10
4.5 MULTI-MODE PARALLEL PORT ...................................................................................................................11
4.6 FDC INTERFACE .........................................................................................................................................16
4.7 KBC INTERFACE .........................................................................................................................................18
4.8 POWER PINS ...........................................................................................................................................18
4.9 ACPI INTERFACE ........................................................................................................................................18
5. FDC FUNCTIONAL DESCRIPTION ...........................................................................................................19
5.1 W83977EF-AW/EG FDC .........................................................................................................................19
5.1.1 AT interface........................................................................................................................................19
5.1.2 FIFO (Data)........................................................................................................................................19
5.1.3 Data Separator ..................................................................................................................................20
5.1.4 Write Precompensation....................................................................................................................20
5.1.5 Perpendicular Recording Mode ......................................................................................................20
5.1.6 FDC Core ...........................................................................................................................................21
5.1.7 FDC Commands................................................................................................................................21
5.2 REGISTER DESCRIPTIONS...........................................................................................................................33
5.2.1 Status Register A (SA Register) (Read base address + 0) ........................................................33
5.2.2 Status Register B (SB Register) (Read base address + 1) ........................................................35
5.2.3 Digital Output Register (DO Register) (Write base address + 2)...............................................37
5.2.4 Tape Drive Register (TD Register) (Read base address + 3)....................................................37
5.2.5 Main Status Register (MS Register) (Read base address + 4)..................................................38
5.2.6 Data Rate Register (DR Register) (Write base address + 4) .....................................................38
5.2.7 FIFO Register (R/W base address + 5).........................................................................................40
5.2.8 Digital Input Register (DI Register) (Read base address + 7)....................................................42
5.2.9 Configuration Control Register (CC Register) (Write base address + 7) .................................43
6. UART PORT ...................................................................................................................................................45
6.1 UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART A, UART B)..........................................45
6.2 REGISTER ADDRESS ...................................................................................................................................45
6.2.1 UART Control Register (UCR) (Read/Write) ................................................................................45
6.2.2 UART Status Register (USR) (Read/Write) ..................................................................................48
Publication Release Date: January, 2010
-II - Revision 1.5
W83977EF-AW /W83977EG-AW
6.2.3 Handshake Control Register (HCR) (Read/Write) .......................................................................48
6.2.4 Handshake Status Register (HSR) (Read/Write).........................................................................49
6.2.5 UART FIFO Control Register (UFR) (Write only).........................................................................50
6.2.6 Interrupt Status Register (ISR) (Read only)..................................................................................51
6.2.7 Interrupt Control Register (ICR) (Read/Write) ..............................................................................52
6.2.8 Programmable Baud Generator (BLL/BHL) (Read/Write) ..........................................................52
6.2.9 User-defined Register (UDR) (Read/Write) ..................................................................................52
7. PARALLEL PORT ........................................................................................................................................54
7.1 PRINTER INTERFACE LOGIC........................................................................................................................54
7.2 ENHANCED PARALLEL PORT (EPP) ...........................................................................................................55
7.2.1 Data Swapper....................................................................................................................................56
7.2.2 Printer Status Buffer .........................................................................................................................56
7.2.3 Printer Control Latch and Printer Control Swapper .....................................................................57
7.2.4 EPP Address Port .............................................................................................................................57
7.2.5 EPP Data Port 0-3 ............................................................................................................................58
7.2.6 Bit Map of Parallel Port and EPP Registers..................................................................................58
7.2.7 EPP Pin Descriptions .......................................................................................................................59
7.2.8 EPP Operation...................................................................................................................................59
7.3 EXTENDED CAPABILITIES PARALLEL (ECP) PORT.....................................................................................60
7.3.1 ECP Register and Mode Definitions.........................................................................................60
7.3.2 Data and ecpAFifo Port....................................................................................................................61
7.3.3 Device Status Register (DSR).........................................................................................................61
7.3.4 Device Control Register (DCR).......................................................................................................62
7.3.5 CFIFO (Parallel Port Data FIFO) Mode = 010..............................................................................63
7.3.6 ECPDFIFO (ECP Data FIFO) Mode = 011 ...................................................................................63
7.3.7 TFIFO (Test FIFO Mode) Mode = 110...........................................................................................63
7.3.8 CNFGA (Configuration Register A) Mode = 111..........................................................................63
7.3.9 CNFGB (Configuration Register B) Mode = 111..........................................................................63
7.3.10 ECR (Extended Control Register) Mode = all.............................................................................64
7.3.11 Bit Map of ECP Port Registers......................................................................................................65
7.3.12 ECP Pin Descriptions.....................................................................................................................66
7.3.13 ECP Operation ................................................................................................................................67
7.3.14 FIFO Operation ...............................................................................................................................67
7.3.15 DMA Transfers ................................................................................................................................68
7.3.16 Programmed I/O (NON-DMA) Mode............................................................................................68
7.4 EXTENSION FDD MODE (EXTFDD) ..........................................................................................................68
7.5 EXTENSION 2FDD MODE (EXT2FDD)......................................................................................................68
8.KEYBOARD CONTROLLER ........................................................................................................................69
8.1 OUTPUT BUFFER.........................................................................................................................................69
8.2 INPUT BUFFER.............................................................................................................................................69
8.3 STATUS REGISTER......................................................................................................................................70
8.4 COMMANDS .................................................................................................................................................71
8.5 HARDWARE GATEA20/KEYBOARD RESET CONTROL LOGIC...................................................................72
Publication Release Date: January, 2010
-III - Revision 1.5
W83977EF-AW /W83977EG-AW
8.5.1 KB Control Register (Logic Device 5, CR-F0) ..............................................................................73
8.5.2 Port 92 Control Register (Default Value = 0x24)....................................................................73
8.6 ONNOW / SECURITY KEYBOARD AND MOUSE WAKE-UP...........................................................................74
8.6.1 Keyboard Wake-Up Function ..........................................................................................................74
8.6.2 Keyboard Password Wake-Up Function .......................................................................................74
8.6.3 Mouse Wake-Up Function ...............................................................................................................74
9. GENERAL PURPOSE I/O ............................................................................................................................75
9.1 BASIC I/O FUNCTIONS...................................................................................................................................77
9.2 ALTERNATE I/O FUNCTIONS.........................................................................................................................79
9.2.1 Interrupt Steering .................................................................................................................................79
9.2.2 Watch Dog Timer Output .....................................................................................................................80
9.2.3 Power LED ...........................................................................................................................................80
9.2.4 General Purpose Address Decoder ......................................................................................................80
10. PLUG AND PLAY CONFIGURATION .....................................................................................................81
10.1 COMPATIBLE PNP .......................................................................................................................................81
10.1.1 Extended Function Registers ..............................................................................................................81
10.1.2 Extended Functions Enable Registers (EFERs) .................................................................................82
10.1.3 Extended Function Index Registers (EFIRs), Extended Function Data Registers(EFDRs) ...............82
10.2 CONFIGURATION SEQUENCE.......................................................................................................................82
10.2.1 Enter the extended function mode.......................................................................................................82
10.2.2 Configurate the configuration registers .............................................................................................83
10.2.3 Exit the extended function mode.........................................................................................................83
10.2.4 Software programming example.........................................................................................................83
11. ACPI REGISTERS FEATURES ................................................................................................................84
12. CONFIGURATION REGISTER .................................................................................................................85
12.1 CHIP (GLOBAL) CONTROL REGISTER.......................................................................................................85
12.2 LOGICAL DEVICE 0 (FDC) .......................................................................................................................91
12.3 LOGICAL DEVICE 1 (PARALLEL PORT)......................................................................................................95
12.4 LOGICAL DEVICE 2 (UART A)¢) ..............................................................................................................95
12.5 LOGICAL DEVICE 3 (UART B)..................................................................................................................96
12.6 LOGICAL DEVICE 5 (KBC) ........................................................................................................................99
12.7 LOGICAL DEVICE 7 (GP I/O PORT I) ......................................................................................................100
12.8 LOGICAL DEVICE 8 (GP I/O PORT II) .....................................................................................................104
12.9 LOGICAL DEVICE A (ACPI).....................................................................................................................109
13.SPECIFICATIONS ......................................................................................................................................116
13.1 ABSOLUTE MAXIMUM RATINGS...............................................................................................................116
13.2 DC CHARACTERISTICS ....................................................................................................................116
13.3 AC CHARACTERISTICS ...........................................................................................................................120
13.3.1 FDC: Data rate = 1 MB, 500 KB, 300 KB, 250 KB/sec. ..........................................................120
13.3.2 UART/Parallel Port .......................................................................................................................122
Publication Release Date: January, 2010
-IV - Revision 1.5
W83977EF-AW /W83977EG-AW
13.3.3 Parallel Port Mode Parameters...................................................................................................122
13.3.4 EPP Data or Address Read Cycle Timing Parameters...........................................................123
13.3.5 EPP Data or Address Write Cycle Timing Parameters ...........................................................124
13.3.6 Parallel Port FIFO Timing Parameters.......................................................................................125
13.3.7 ECP Parallel Port Forward Timing Parameters........................................................................125
13.3.8 ECP Parallel Port Reverse Timing Parameters .......................................................................125
13.3.9 KBC Timing Parameters ..............................................................................................................126
13.3.10 GPIO Timing Parameters .........................................................................................................127
13.3.11 Keyboard/Mouse Timing Parameters.....................................................................................127
14. TIMING WAVEFORMS .............................................................................................................................128
14.1 FDC ........................................................................................................................................................128
14.2 UART/PARALLEL....................................................................................................................................129
14.2.1 Modem Control Timing................................................................................................................130
14.3 PARALLEL PORT.....................................................................................................................................131
14.3.1 Parallel Port Timing .....................................................................................................................131
14.3.2 EPP Data or Address Read Cycle (EPP Version 1.9)............................................................132
14.3.3 EPP Data or Address Write Cycle (EPP Version 1.9)............................................................133
14.3.4 EPP Data or Address Read Cycle (EPP Version 1.7)............................................................134
14.3.5 EPP Data or Address Write Cycle (EPP Version 1.7)............................................................135
14.3.6 Parallel Port FIFO Timing ...........................................................................................................135
14.3.7 ECP Parallel Port Forward Timing ............................................................................................136
14.3.8 ECP Parallel Port Reverse Timing ............................................................................................136
14.4 KBC ........................................................................................................................................................137
14.4.1 Write Cycle Timing ......................................................................................................................137
14.4.2 Read Cycle Timing ......................................................................................................................137
14.4.3 Send Data to K/B .........................................................................................................................137
14.4.4 Receive Data from K/B ...............................................................................................................138
14.4.5 Input Clock....................................................................................................................................138
14.4.6 Send Data to Mouse....................................................................................................................138
14.4.7 Receive Data from Mouse..........................................................................................................138
14.5 GPIO WRITE TIMING DIAGRAM..............................................................................................................139
14.6 MASTER RESET (MR) TIMING ................................................................................................................139
14.7 KEYBOARD/MOUSE WAKE-UP TIMING....................................................................................................139
14.8 ISA READ TIMING ....................................................................................................................................140
14.9 ISA WRITE TIMING...................................................................................................................................141
15. APPLICATION CIRCUITS........................................................................................................................142
15.1 PARALLEL PORT EXTENSION FDD.........................................................................................................142
15.2 PARALLEL PORT EXTENSION 2FDD.......................................................................................................143
15.3 FOUR FDD MODE...................................................................................................................................144
16. ORDERING INFORMATION ..................................................................................................................144
17. TOP MARKING SPECIFICATIONS........................................................................................................144
Publication Release Date: January, 2010
-V - Revision 1.5
W83977EF-AW /W83977EG-AW
18. PACKAGE DIMENSIONS ........................................................................................................................145
19. REVISION HISTORY.................................................................................................................................146
Publication Release Date: January, 2010
-VI - Revision 1.5
W83977EF-AW /W83977EG-AW
1. GENERAL DESCRIPTION
W83977EF-AW/EG-AW is an evolving product from Winbond's most popular I/O chip W83877F ---
which integrates the disk drive adapter, serial port (UART), IrDA 1.0 SIR, parallel port, configurable
plug-and-play registers for the whole chip --- plus additional powerful features: ACPI, 8042 keyboard
controller with PS/2 mouse support, 14 general purpose I/O ports, full 16-bit address decoding,
OnNow keyboard Wake-Up, OnNow mouse Wake-Up.
The disk drive adapter functions of W83977EF-AW/EG-AW include a floppy disk drive controller
compatible with the industry standard 82077/ 765, data separator, write pre-compensation circuit,
decode logic, data rate selection, clock generator, drive interface control logic, and interrupt and DMA
logic. The wide range of functions integrated onto the W83977EF-AW greatly reduces the number of
components required for interfacing with floppy disk drives. The W83977EF-AW/EG-AW supports four
360K, 720K, 1.2M, 1.44M, or 2.88M disk drives and data transfer rates of 250 Kb/s, 300 Kb/s, 500
Kb/s,1 Mb/s, and 2 Mb/s.
W83977EF-AW/EG-AW provides two high-speed serial communication ports (UARTs), one of which
supports serial Infrared communication. Each UART includes a 16-byte send/receive FIFO, a
programmable baud rate generator, complete modem control capability, and a processor interrupt
system. Both UARTs provide legacy speed with baud rate up to 115.2k bps and also advanced speed
with baud rates of 230k, 460k, or 921k bps which support higher speed modems.
W83977EF-AW/EG-AW supports one PC-compatible printer port (SPP), Bi-directional Printer port
(BPP) and also Enhanced Parallel Port (EPP) and Extended Capabilities Port (ECP). Through the
printer port interface pins, also available are: Extension FDD Mode and Extension 2FDD Mode
allowing one or two external floppy disk drives to be connected.
The configuration registers support mode selection, function enable/disable, and power down function
selection. Furthermore, the configurable PnP features are compatible with the plug-and-play feature
TM
demand of Windows 95 , which makes system resource allocation more efficient than ever.
W83977EF-AW/EG-AW provides functions that complies with ACPI (Advanced Configuration and
Power Interface), which includes support of legacy and ACPI power management through SMI or
SCI
function pins. W83977EF-AW/EG-AW also has auto power management to reduce power
consumption.
The keyboard controller is based on 8042 compatible instruction set with a 2K Byte programmable
TM
ROM and a 256-Byte RAM bank. Keyboard BIOS firmware are available with optional AMIKEY -2,
TM
Phoenix MultiKey/42 , or customer code.
W83977EF-AW/EG-AW provides a set of flexible I/O control functions to the system designer through
a set of General Purpose I/O ports. These GPIO ports may serve as simple I/O or may be individually
configured to provide a predefined alternate function.
W83977EF-AW/EG-AW also supports Power-loss control, and makes the system never miss to
TM
detect any Wake-Up event provided by the chipset such as INTEL PIIX4 .
W83977EF-AW/EG-AW is made to fully comply with Microsoft PC98 Hardware Design Guide.
IRQs, DMAs, and I/O space resource are flexible to adjust to meet ISA PnP requirement. Moreover
W83977EF-AW/EG-AW is made to meet the specification of PC98's requirement in the power
management: ACPI and DPM (Device Power Management).
Another benifit is that W83977EF-AW/EG-AW is of the same pin assignment of W83977AF, W83977F,
W83977TF, W83977ATF. Thus makes the design very flexible.
Publication Release Date: January, 2010
-1 - Revision 1.5
W83977EF-AW /W83977EG-AW
2. FEATURES
General
• Plug & Play 1.0A compatible
• Support 12 IRQs, 4 DMA channels, full 16-bit address decoding
• Capable of ISA Bus IRQ Sharing
• Compliant with Microsoft PC98 Hardware Design Guide
• Support DPM (Device Power Management), ACPI
• Report ACPI status interrupt by SCI# signal issued from any of the 12 IQRs pins or GPIO xx
• Programmable configuration settings
• single 24/48 Mhz clock input
FDC
• Compatible with IBM PC AT disk drive systems
• Variable write pre-compensation with track selectable capability
• Support vertical recording format
• DMA enable logic
• 16-byte data FIFOs
• Support floppy disk drives and tape drives
• Detects all overrun and underrun conditions
• Built-in address mark detection circuit to simplify the read electronics
• FDD anti-virus functions with software write protect and FDD write enable signal (write data signal
was forced to be inactive)
• Support up to four 3.5-inch or 5.25-inch floppy disk drives
• Completely compatible with industry standard 82077
• 360K/720K/1.2M/1.44M/2.88M format; 250K, 300K, 500K, 1M, 2M bps data transfer rate
• Support 3-mode FDD, and its Win95 driver
UART
• Two high-speed 16550 compatible UARTs with 16-byte send/receive FIFOs
• MIDI compatible
• Fully programmable serial-interface characteristics:
--- 5, 6, 7 or 8-bit characters
--- Even, odd or no parity bit generation/detection
--- 1, 1.5 or 2 stop bits generation
Publication Release Date: January, 2010
-2 - Revision 1.5
W83977EF-AW /W83977EG-AW
• Internal diagnostic capabilities:
--- Loop-back controls for communications link fault isolation
--- Break, parity, overrun, framing error simulation
16
• Programmable baud generator allows division of 1.8461 Mhz and 24 Mhz by 1 to (2 -1)
• Maximum baud rate up to 921k bps for 14.769 Mhz and 1.5M bps for 24 Mhz
Infrared
• Support IrDA version 1.0 SIR protocol with maximum baud rate up to 115.2K bps
• Support SHARP ASK-IR protocol with maximum baud rate up to 57,600 bps
Parallel Port
• Compatible with IBM parallel port
• Support PS/2 compatible bi-directional parallel port
• Support Enhanced Parallel Port (EPP) − Compatible with IEEE 1284 specification
• Support Extended Capabilities Port (ECP) − Compatible with IEEE 1284 specification
• Extension FDD mode supports disk drive B; and Extension 2FDD mode supports disk drives A and
B through parallel port
• Enhanced printer port back-drive current protection
Keyboard Controller
TM TM
• 8042 based with optional F/W from AMIKKEY -2, Phoenix MultiKey/42 or customer code
• With 2K bytes of programmable ROM, and 256 bytes of RAM
• Asynchronous Access to Two Data Registers and One status Register
• Software compatibility with the 8042 and PC87911 microcontrollers
• Support PS/2 mouse
• Support port 92
• Support both interrupt and polling modes
• Fast Gate A20 and Hardware Keyboard Reset
• 8 Bit Timer/ Counter
• Support binary and BCD arithmetic
• 6MHz, 8 MHz, 12 MHz, or 16 MHz operating frequency
Publication Release Date: January, 2010
-3 - Revision 1.5
W83977EF-AW /W83977EG-AW
General Purpose I/O Ports
• 14 programmable general purpose I/O ports; 6 dedicate, 8 optional
• General purpose I/O ports can serve as simple I/O ports, interrupt steering inputs, watching dog
timer output, power LED output, infrared I/O pins, general purpose address decoder, KBC control
I/O pins
OnNow Funtions
• Keyboard Wake-Up by programmable keys
• Mouse Wake-Up by programmable buttons
Package
• 128-pin PQFP
Publication Release Date: January, 2010
-4 - Revision 1.5
W83977EF-AW /W83977EG-AW
3. PIN CONFIGURATION
IR IRQ14/ Q14/G GP14 P14 103 103 64 64 VBA VBAT T
IR IRQ15/ Q15/G GP15 P15 104 104 63 63 XT XTA AL L1 1
IO IOR R# # 105 105 62 62 VSS VSS
IO IOW W# # 106 106 61 61 XT XTA AL L2 2
AEN AEN# # 107 107 60 60 MDA MDAT TA A
IIO OC CHRDY HRDY 108 108 59 59 KD KDATA ATA
D0 D0 109 109 58 58 KBLOCK KBLOCK//GP13 GP13
D1 D1 110 110 57 57 KBR KBRS ST T/G /GP12 P12
D2 D2 111 111 56 56 GA20 GA20//G GP11 P11
D3 D3 112 112 55 55 VCC VCC
D4 D4 113 113 54 54 DCD DCDB# B#
W83977EF-AW W83977EF-AW
D5 D5 114 114 53 53 S SO OU UT TB/ B/PE PEN4 N48 8
VCC VCC 115 115 52 52 SIN SINB B
D6 D6 116 116 51 51 DT DTRB RB# #
D7 D7 117 117 50 50 RT RTS SB B
W83977EG-AW W83977EG-AW
MR MR 118 118 49 49 DS DSRB RB# #
D DA AC CK0#/GP16 K0#/GP16 119 119 48 48 C CT TSB# SB#
VSS VSS 120 120 47 47 DCD DCDA# A#
SC SCI#/D I#/DR RQ Q0/ 0/GP17 GP17 121 121 46 46 SOU SOUT TA A//P PEN ENKBC KBC
DA DACK CK1 1# # 122 122 45 45 SIN SINA A
DR DRQ Q1 1 123 123 44 44 D DT TR RA#/PN A#/PNPC PCSV# SV#
DA DACK CK2 2# # 124 124 43 43 R RT TSA# SA#/H /HEFR EFRA AS S
DR DRQ Q2 2 125 125 42 42 DS DSRA RA# #
DA DACK CK3 3# # 126 126 41 41 C CT TSA# SA#
DR DRQ Q3 3 127 127 40 40 GP24 GP24
TC TC 128 128 39 39 SU SUSC SC#/GP25 #/GP25
Publication Release Date: January, 2010
-5 - Revision 1.5
CL CLK KI IN N 1 1 102 102 IRQ12 IRQ12
DR DRVD VDE EN N0 0 2 2 101 101 IRQ11 IRQ11
DR DRVD VDE EN N1/GP10/ 1/GP10/SC SCII 3 3 100 100 IRQ10 IRQ10
D DSKCH SKCHG G# # 4 4 99 99 IRQ1 IRQ1
H HEAD EAD# # 5 5 98 98 IRQ3 IRQ3
RD RDAT ATA# A# 6 6 97 97 IRQ4 IRQ4
WP WP# # 7 7 96 96 IRQ5 IRQ5
T TR RAK0# AK0# 8 8 95 95 IRQ6 IRQ6
WE WE# # 9 9 94 94 IRQ7 IRQ7
WD WD# # 10 10 93 93 NC NC
ST STEP EP# # 11 11 92 92 IRQ9 IRQ9
DIR# DIR# 12 12 91 91 A15 A15
MO MOB B# # 13 13 90 90 VSS VSS
D DSA# SA# 14 14 89 89 A14 A14
D DSB# SB# 15 15 88 88 A13 A13
MO MOA A# # 16 16 87 87 A12 A12
IN IND DEX# EX# 17 17 86 86 A11 A11
SLC SLCT T 18 18 85 85 VCC VCC
PE PE 19 19 84 84 A10 A10
VCC VCC 20 20 83 83 A9 A9
BU BUSY SY 21 21 82 82 A8 A8
AC ACK# K# 22 22 81 81 A7 A7
PD PD7 7 23 23 80 80 A6 A6
PD PD6 6 24 24 79 79 A5 A5
VSS VSS 25 25 78 78 A4 A4
PD PD5 5 26 26 77 77 A3 A3
PD PD4 4 27 27 76 76 A2 A2
PD PD3 3 28 28 75 75 A1 A1
PD PD2 2 29 29 74 74 A0 A0
PD PD1 1 30 30 73 73 PAN PANS SW WIN IN# #//GP23 GP23
PD PD0 0 31 31 72 72 PAN PANS SW WOU OUT# T#/G /GP22 P22
SLIN SLIN# # 32 32 71 71 VSB VSB
IN INT T# # 33 33 70 70 SMI# SMI#/G /GP21 P21
ERR ERR# # 34 34 69 69 P PW WRCT RCTL L# #/ /G GP P2 20 0
AFD AFD# # 35 35 68 68 MC MCL LK K
ST STB B# # 36 36 67 67 KC KCLK LK
RRX RRX# # 37 37 66 66 RIB RIB# #
RT RTX# X# 38 38 65 65 RIA RIA# #
W83977EF-AW /W83977EG-AW
4. PIN DESCRIPTION
Note: Please refer to Section 11.2 DC CHARACTERISTICS for details.
I/O - TTL level bi-directional pin with 6 mA source-sink capability
6t
I/O - TTL level bi-directional pin with 8 mA source-sink capability
8t
I/O - CMOS level bi-directional pin with 8 mA source-sink capability
8
I/O - TTL level bi-directional pin with 12 mA source-sink capability
12t
I/O - CMOS level bi-directional pin with 12 mA source-sink capability
12
I/O - CMOS level bi-directional pin with 16 mA source-sink capability with internal pull-up resistor
16u
I/OD - CMOS level bi-directional pin open drain output with 16 mA sink capability with internal pull-up resistor
16u
I/O - TTL level bi-directional pin with 24 mA source-sink capability
24t
OUT - TTL level output pin with 8 mA source-sink capability
8t
OUT - TTL level output pin with 12 mA source-sink capability
12t
OD - Open-drain output pin with 12 mA sink capability
12
OD - Open-drain output pin with 24 mA sink capability
24
IN - TTL level input pin
t
IN - CMOS level input pin
c
IN - CMOS level input pin with internal pull-up resitor
cu
IN - CMOS level Schmitt-triggered input pin
cs
IN - TTL level Schmitt-triggered input pin
ts
IN - TTL level Schmitt-triggered input pin with internal pull-up resistor
tsu
4.1 Host Interface
SYMBOL PIN I/O FUNCTION
A0−A10 74-84 IN System address bus bits 0-10
t
A11-A14 86-89 IN System address bus bits 11-14
t
A15 91 IN System address bus bit 15
t
109-114 I/O System data bus bits 0-5
D0−D5
12t
116-117 I/O System data bus bits 6-7
D6−D7
12t
IOR# 105 IN CPU I/O read signal
ts
IOW# 106 IN CPU I/O write signal
ts
AEN# 107 IN System address bus enable
ts
IOCHRDY 108 OD In EPP Mode, this pin is the IO Channel Ready output to extend
24
the host read/write cycle.
MR 118 IN Master Reset; Active high; MR is low during normal operations.
ts
Publication Release Date: January, 2010
-6 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.1 Host Interface, continued
SYMBOL PIN I/O FUNCTION
DACK0# 119 IN DMA Channel 0 Acknowledge signal. (CR2C bit 5_4 = 00,
tsu
default)
GP16 I/O General purpose I/O port 1bit 6. (CR2C bit 5_4 = 01)
12t
(WDTO)
Alternate function from GP16: Watch dog timer output
P15 I/O KBC P15 I/O port. (CR2C bit 5_4 = 10)
12t
DRQ0 121 OUT DMA Channel 0 request signal. (CR2C bit 7_6 = 00, default)
12t
GP17 I/O General purpose I/O port 1bit 7. (CR2C bit 7_6 = 01)
12t
(PLEDO)
Alternate Function from GP17: Power LED output.
P14 I/O KBC P14 I/O port (CR2C bit 7_6 = 10)
12t
SCI# OUT System Control Interrupt (CR2C bit 7_6 = 11)
12t
DACK1# 122 IN DMA Channel 1 Acknowledge signal
ts
DRQ1 123 OUT DMA Channel 1 request signal
12t
DACK2# 124 IN DMA Channel 2 Acknowledge signal
ts
DRQ2 125 OUT DMA Channel 2 request signal
12t
DACK3# 126 IN DMA Channel 3 Acknowledge signal
ts
DRQ3 127 OUT DMA Channel 3 request signal
12t
TC 128 IN Terminal Count. When active, this pin indicates termination of a
ts
DMA transfer.
IRQ1 99 OUT Interrupt request 1
12t
IRQ3 98 OUT Interrupt request 3
12t
IRQ4 97 OUT Interrupt request 4
12t
IRQ5 96 OUT Interrupt request 5
12t
IRQ6 95 OUT Interrupt request 6
12t
IRQ7 94 OUT Interrupt request 7
12t
IRQ9 92 OUT Interrupt request 9
12t
IRQ10 100 OUT Interrupt request 10
12t
IRQ11 101 OUT Interrupt request 11
12t
IRQ12 102 OUT Interrupt request 12
12t
Publication Release Date: January, 2010
-7 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.1 Host Interface, continued
SYMBOL PIN I/O FUNCTION
IRQ14 103 OUT Interrupt request 14. (CR2C bit 1_0 = 00, default)
12t
GP14 I/O General purpose I/O port 1 bit 4. (CR2C bit 1_0 = 01)
12t
(GPACS1#) Alternate Function 1 from GP14: General purpose address
decode output.
(P17) Alternate Function 2 from GP14: KBC P17 I/O port.
PLEDO OUT Power LED output. (CR2C bit 1_0 = 10)
12t
IRQ15 104 OUT Interrupt request 15.(CR2C bit 3_2 = 00, default)
12t
GP15 I/O General purpose I/O port 1 bit 5. (CR2C bit 3_2 = 01)
12t
(GPACS2#) Alternate Function 1 from GP15: General purpose address write
enable output.
(P12) Alternate Function 2 from GP15: KBC P12 I/O port.
WDT OUT Watch-Dog timer output. (CR2C bit 3_2 = 10)
12t
CLKIN 1 IN 24 or 48 MHz clock input, selectable through bit 5 of CR24.
t
4.2 General Purpose I/O Port
SYMBOL PIN I/O FUNCTION
PWR_CTL# 69 OD Power supply control
16u
GP20 I/O General purpose I/O port 2 bit 0.
16tu
(KBRST) Alternate Function from GP20: Keyboard reset (KBC P20)
SMI # 70 OD
12t
For the power management, the SMI is active low by the power
management events, that generate and SCI in ACPI mode.
(CR2B bit 4_3 = 00, default)
GP21 I/O General purpose I/O port 2 bit 1. (CR2B bit 4_3 = 01)
12t
(P13) Alternate Function from GP21: KBC P13 I/O port.
P16 I/O KBC P16 I/O port. (CR2B bit 4_3 = 10)
12t
PANSWOUT#
72 OD Panel Switch output. (CR2B bit 5 = 0, default)
12t
GP22
I/O General purpose I/O port 2 bit 2. (CR2B bit 5 = 1)
12t
(P14) Alternate Function from GP22: KBC P14 I/O port.
Publication Release Date: January, 2010
-8 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.2 General Purpose I/O Port ,continued
SYMBOL PIN I/O FUNCTION
PANSWIN# 73 IN Panel Switch input. (CR2B bit 7_6 = 00, default)
t
GP23 I/O General purpose I/O port 2 bit 3. (CR2B bit 7_6 = 01)
12t
(P15) Alternate Function from GP23: KBC P15 I/O port
SUSC#
39 IN Suspend C input
ts
(GA20)
Alternate Function from GP25: GATE A20 (KBC P21)
GP25 I/O General purpose I/O port 2 bit 5.
12
GP24 40 I/O General purpose I/O port 2 bit 4.
12
4.3 Serial Port Interface
SYMBOL PIN I/O FUNCTION
CTSA# 41 IN Clear To Send is the modem control input.
t
48
CTSB# The function of these pins can be tested by reading Bit 4 of the
handshake status register.
DSRA# 42 IN Data Set Ready. An active low signal indicates the modem or
t
data set is ready to establish a communication link and transfer
DSRB# 49
data to the UART.
43 I/O UART A Request To Send. An active low signal informs the
8t
RTSA#
modem or data set that the controller is ready to send data.
During power-on reset, this pin is pulled down internally and is
HEFRAS
defined as HEFRAS, which provides the power-on value for
CR26 bit 6 (HEFRAS). A 4.7 kΩ is recommended if intends to
pull up. (select 370H as configuration I/O port′s address)
50 I/O UART B Request To Send. An active low signal informs the
8t
RTSB#
modem or data set that the controller is ready to send data.
Publication Release Date: January, 2010
-9 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.3 Serial Port Interface, continued
SYMBOL PIN I/O FUNCTION
44 I/O UART A Data Terminal Ready. An active low signal informs the
8t
DTRA#
modem or data set that the controller is ready to communicate.
During power-on reset, this pin is pulled down internally and is
PNPCSV#
defined as PNPCSV#, which provides the power-on value for
CR24 bit 0 (PNPCSV#). A 4.7 kΩ is recommended if intends to
pull up. (clear the default value of FDC, UARTs, and PRT)
51 I/O UART B Data Terminal Ready. An active low signal informs the
8t
DTRB#
modem or data set that controller is ready to communicate.
SINA 45, 52 IN Serial Input. Used to receive serial data through the
t
SINB communication link.
46 I/O UART A Serial Output. Used to transmit serial data out to the
8t
SOUTA
communication link.
During power-on reset, this pin is pulled down internally and is
PENKBC
defined as PENKBC, which provides the power-on value for
CR24 bit 2 (ENKBC). A 4.7 k Ω resistor is recommended if
intends to pull up. (enable KBC)
SOUTB 53 I/O UART B Serial Output. During power-on reset, this pin is pulled
8t
down internally and is defined as PEN48, which provides the
PEN48
power-on value for CR24 bit 6 (EN48). A 4.7 kΩ resistor is
recommended if intends to pull up.
DCDA# 47 IN Data Carrier Detect. An active low signal indicates the modem or
t
data set has detected a data carrier.
DCDB# 54
RIA# 65 IN Ring Indicator. An active low signal indicates that a ring signal is
t
being received from the modem or data set.
66
RIB#
4.4 Infrared Interface
SYMBOL PIN I/O FUNCTION
IRRX 37 IN Infrared Receiver input.
cs
IRTX 38 OUT Infrared Transmitter Output.
12t
Publication Release Date: January, 2010
-10 - Revision 1.5
W83977EF-AW /W83977EG-AW
4.5 Multi-Mode Parallel Port
The following pins have alternate functions, which are controlled by CR28 and L3-CRF0.
SYMBOL PIN I/O FUNCTION
PRINTER MODE: SLCT
SLCT 18 IN
t
An active high input on this pin indicates that the printer is
selected. This pin is pulled high internally. Refer to description of
the parallel port for definition of this pin in ECP and EPP mode.
EXTENSION FDD MODE:
OD WE2#
12
This pin is for Extension FDD B; its function is the same as the
WE# pin of FDC.
EXTENSION 2FDD MODE: WE2#
OD
12
This pin is for Extension FDD A and B; it function is the same as
the WE# pin of FDC.
PE 19 IN PRINTER MODE: PE
t
An active high input on this pin indicates that the printer has
detected the end of the paper. This pin is pulled high internally.
Refer to description of the parallel port for definition of this pin in
ECP and EPP mode.
OD EXTENSION FDD MODE: WD2#
12
This pin is for Extension FDD B; its function is the same as the
WD# pin of FDC.
OD EXTENSION 2FDD MODE: WD2#
12
This pin is for Extension FDD A and B; its function is the same as
the WD# pin of FDC.
Publication Release Date: January, 2010
-11 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.5 Multi-Mode Parallel Port, continued
SYMBOL PIN I/O FUNCTION
BUSY 21 IN PRINTER MODE: BUSY
t
An active high input indicates that the printer is not ready to
receive data. This pin is pulled high internally. Refer to
description of the parallel port for definition of this pin in ECP and
EPP mode.
OD
12
EXTENSION FDD MODE: MOB2#
This pin is for Extension FDD B; the function of this pin is the
same as the MOB# pin of FDC.
OD
12
EXTENSION 2FDD MODE:MOB2#
This pin is for Extension FDD A and B; the function of this pin is
the same as the MOB# pin of FDC.
ACK# 22 IN PRINTER MODE: ACK#
t
An active low input on this pin indicates that the printer has
received data and is ready to accept more data. This pin is
pulled high internally. Refer to description of the parallel port for
definition of this pin in ECP and EPP mode.
EXTENSION FDD MODE: DSB2#
OD
12
This pin is for the Extension FDD B; its functions is the same as
the DSB# pin of FDC.
EXTENSION 2FDD MODE: DSB2#
OD
12
This pin is for Extension FDD A and B; it functions is the same as
the DSB# pin of FDC.
ERR# 34 IN PRINTER MODE: ERR#
t
An active low input on this pin indicates that the printer has
encountered an error condition. This pin is pulled high internally.
Refer to description of the parallel port for definition of this pin in
ECP and EPP mode.
EXTENSION FDD MODE: HEAD2#
OD
12
This pin is for Extension FDD B; its function is the same as the
HEAD#pin of FDC.
OD
12
EXTENSION 2FDD MODE: HEAD2#
This pin is for Extension FDD A and B; its function is the same as
the HEAD# pin of FDC.
Publication Release Date: January, 2010
-12 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.5 Multi-Mode Parallel Port, continued
SYMBOL PIN I/O FUNCTION
SLIN# 32 OD
PRINTER MODE: SLIN#
12
Output line for detection of printer selection. This pin is pulled
high internally. Refer to description of the parallel port for
definition of this pin in ECP and EPP mode.
EXTENSION FDD MODE:STEP2#
OD
12
This pin is for Extension FDD B; its function is the same as the
STEP# pin of FDC.
EXTENSION 2FDD MODE: STEP2#
OD
12
This pin is for Extension FDD A and B; its function is the same as
the STEP# pin of FDC.
INIT# 33 OD PRINTER MODE: INIT#
12
Output line for the printer initialization. This pin is pulled high
internally. Refer to description of the parallel port for definition of
this pin in ECP and EPP mode.
EXTENSION FDD MODE: DIR2#
OD
12
This pin is for Extension FDD B; its function is the same as the
DIR# pin of FDC.
EXTENSION 2FDD MODE: DIR2#
OD
12
This pin is for Extension FDD A and B; its function is the same as
the DIR# pin of FDC.
AFD# 35 OD PRINTER MODE: AFD#
12
An active low output from this pin causes the printer to auto feed
a line after a line is printed. This pin is pulled high internally.
Refer to description of the parallel port for definition of this pin in
ECP and EPP mode.
EXTENSION FDD MODE: DRVDEN0
OD
12
This pin is for Extension FDD B; its function is the same as the
DRVDEN0 pin of FDC.
EXTENSION 2FDD MODE: DRVDEN0
OD
12
This pin is for Extension FDD A and B; its function is the same as
the DRVDEN0 pin of FDC.
Publication Release Date: January, 2010
-13 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.5 Multi-Mode Parallel Port, continued
SYMBOL PIN I/O FUNCTION
STB# 36 OD PRINTER MODE: STB#
12
An active low output is used to latch the parallel data into the
printer. This pin is pulled high internally. Refer to description of
the parallel port for definition of this pin in ECP and EPP mode.
- EXTENSION FDD MODE: This pin is a tri-state output.
- EXTENSION 2FDD MODE: This pin is a tri-state output.
31 I/O PRINTER MODE: PD0
PD0
24t
Parallel port data bus bit 0. Refer to description of the parallel
port for definition of this pin in ECP and EPP mode.
IN EXTENSION FDD MODE: INDEX2#
t
This pin is for Extension FDD B; the function of this pin is the
same as the INDEX# pin of FDC. It is pulled high internally.
IN EXTENSION 2FDD MODE: INDEX2#
t
This pin is for Extension FDD A and B; the function of this pin is
the same as the INDEX# pin of FDC. It is pulled high internally.
30 I/O PRINTER MODE: PD1
PD1
24t
Parallel port data bus bit 1. Refer to description of the parallel
port for definition of this pin in ECP and EPP mode.
IN EXTENSION FDD MODE: TRAK02#
t
This pin is for Extension FDD B; the function of this pin is the
same as the TRAK0# pin of FDC. It is pulled high internally.
EXTENSION. 2FDD MODE: TRAK02#
IN
t
This pin is for Extension FDD A and B; the function of this pin is
the same as the TRAK0# pin of FDC. It is pulled high internally.
29 I/O PRINTER MODE: PD2
PD2
24t
Parallel port data bus bit 2. Refer to description of the parallel
port for definition of this pin in ECP and EPP mode.
EXTENSION FDD MODE: WP2#
IN
t
This pin is for Extension FDD B; the function of this pin is the
same as the WP# pin of FDC. It is pulled high internally.
EXTENSION. 2FDD MODE: WP2#
IN
t
This pin is for Extension FDD A and B; the function of this pin is
the same as the WP# pin of FDC. It is pulled high internally.
Publication Release Date: January, 2010
-14 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.5 Multi-Mode Parallel Port, continued
SYMBOL PIN I/O FUNCTION
28 I/O PRINTER MODE: PD3
PD3
24t
Parallel port data bus bit 3. Refer to description of the parallel
port for definition of this pin in ECP and EPP mode.
IN
t
EXTENSION FDD MODE: RDATA2#
This pin is for Extension FDD B; the function of this pin is the
same as the RDATA# pin of FDC. It is pulled high internally.
IN
t EXTENSION 2FDD MODE: RDATA2#
This pin is for Extension FDD A and B; this function of this pin is
the same as the RDATA# pin of FDC. It is pulled high internally.
27 I/O PRINTER MODE: PD4
PD4
24t
Parallel port data bus bit 4. Refer to description of the parallel
port for definition of this pin in ECP and EPP mode.
IN EXTENSION FDD MODE: DSKCHG2#
t
This pin is for Extension FDD B; the function of this pin is the
same as the DSKCHG# pin of FDC. It is pulled high internally.
EXTENSION 2FDD MODE: DSKCHG2#
IN
t
This pin is for Extension FDD A and B; this function of this pin is
the same as the DSKCHG# pin of FDC. It is pulled high internally.
26 I/O PRINTER MODE: PD5
PD5
24t
Parallel port data bus bit 5. Refer to description of the parallel
port for definition of this pin in ECP and EPP mode.
-
EXTENSION FDD MODE: This pin is a tri-state output.
-
EXTENSION 2FDD MODE: This pin is a tri-state output.
24 I/O PRINTER MODE: PD6
PD6
24t
Parallel port data bus bit 6. Refer to description of the parallel
port for definition of this pin in ECP and EPP mode.
-
EXTENSION FDD MODE: This pin is a tri-state output.
EXTENSION. 2FDD MODE: MOA2#
OD
24
This pin is for Extension FDD A; its function is the same as the
MOA# pin of FDC.
Publication Release Date: January, 2010
-15 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.5 Multi-Mode Parallel Port, continued
SYMBOL PIN I/O FUNCTION
23 I/O PRINTER MODE: PD7
PD7
24t
Parallel port data bus bit 7. Refer to description of the parallel
port for definition of this pin in ECP and EPP mode.
EXTENSION FDD MODE: This pin is a tri-state output.
-
EXTENSION 2FDD MODE: DSA2#
OD
24
This pin is for Extension FDD A; its function is the same as the
DSA# pin of FDC.
4.6 FDC Interface
SYMBOL PIN I/O FUNCTION
DRVDEN0 2 OD Drive Density Select bit 0.
24
DRVDEN1 3 OD Drive Density Select bit 1. (CR2A bit 1_0 = 00, default)
24
GP10 IO General purpose I/O port 1 bit 0. (CR2A bit 1_0 = 01)
24t
(IRQIN1) Alternate Function from GP10: Interrupt channel input.
P12 IO KBC P12 I/O port. (CR2A bit 1_0 = 10)
24t
SCI# OUT System Control Interrupt (CR2A bit 1_0 = 11)
12t
HEAD# 5 OD Head select. This open drain output determines which disk drive
24
head is active.
Logic 1 = side 0
Logic 0 = side 1
WE# 9 OD Write enable. An open drain output.
24
WD# 10 OD Write data. This logic low open drain writes pre-compensation
24
serial data to the selected FDD. An open drain output.
STEP# 11 OD Step output pulses. This active low open drain output produces a
24
pulse to move the head to another track.
DIR# 12 OD Direction of the head step motor. An open drain output.
24
Logic 1 = outward motion
Logic 0 = inward motion
MOB# 13 OD Motor B On. When set to 0, this pin enables disk drive 1. This is
24
an open drain output.
Publication Release Date: January, 2010
-16 - Revision 1.5
W83977EF-AW /W83977EG-AW
1.6 FDC Interface, continued
SYMBOL PIN I/O FUNCTION
DSA# 14 OD Drive Select A. When set to 0, this pin enables disk drive A. This
24
is an open drain output.
DSB# 15 OD Drive Select B. When set to 0, this pin enables disk drive B. This
24
is an open drain output.
MOA# 16 OD Motor A On. When set to 0, this pin enables disk drive 0. This is
24
an open drain output.
DSKCHG# 4 IN Diskette change. This signal is active low at power on and
cs
whenever the diskette is removed. This input pin is pulled up
internally by a 1 KΩ resistor. The resistor can be disabled by bit 7
of L0-CRF0 (FIPURDWN).
RDATA# 6 IN The read data input signal from the FDD. This input pin is pulled
cs
up internally by a 1 KΩ resistor. The resistor can be disabled by
bit 7 of L0-CRF0 (FIPURDWN).
WP# 7 IN Write protected. This active low Schmitt input from the disk drive
cs
indicates that the diskette is write-protected. This input pin is
pulled up internally by a 1 KΩ resistor. The resistor can be
disabled by bit 7 of L0-CRF0 (FIPURDWN).
TRAK0# 8 IN Track 0. This Schmitt-triggered input from the disk drive is active
cs
low when the head is positioned over the outermost track. This
input pin is pulled up internally by a 1 KΩ resistor. The resistor
can be disabled by bit 7 of L0-CRF0 (FIPURDWN).
INDEX# 17 IN This Schmitt-triggered input from the disk drive is active low
cs
when the head is positioned over the beginning of a track marked
by an index hole. This input pin is pulled up internally by a 1 KΩ
resistor. The resistor can be disabled by bit 7 of L0-CRF0
(FIPURDWN).
Publication Release Date: January, 2010
-17 - Revision 1.5
W83977EF-AW /W83977EG-AW
4.7 KBC Interface
SYMBOL PIN I/O FUNCTION
KDATA 59 I/O Keyboard Data
16u
MDATA 60 I/O PS2 Mouse Data
16u
KCLK 67 I/O Keyboard Clock
16u
MCLK 68 I/O PS2 Mouse Clock
16u
GA20 56 I/O KBC GATE A20 (P21) Output. (CR2A bit 6 = 0, default)
12t
GP11 I/O General purpose I/O port 1 bit 1. (CR2A bit 6 = 1)
12t
(IRQIN2) Alternate Function from GP11: Interrupt channel input.
KBRST 57 I/O W83C45 Keyboard Reset (P20) Output. (CR2A bit 7 = 0, default)
12t
GP12 I/O General purpose I/O port 1 bit 2. (CR2A bit 7 = 1)
12t
(WDTO) Alternate Function 1 from GP12 : Watchdog timer output.
KBLOCK 58 IN W83C45 KINH (P17) Input. (CR2B bit 0 = 0, default)
ts
GP13 I/O General purpose I/O port 1 bit 3. (CR2B bit 0 = 1)
16t
4.8 POWER PINS
SYMBOL PIN FUNCTION
VCC 20, 55, 85, +5V power supply for the digital circuitry
115
VSB 71 +5V stand-by power supply for the digital circuitry
GND 25, 62, 90, Ground
120
4.9 ACPI Interface
SYMBOL PIN I/O FUNCTION
VBAT 64 NA battery voltage input
XTAL1 63 IN 32.768Khz Clock Input
C
XTAL2 61 O 32.768Khz Clock Output
8t
Publication Release Date: January, 2010
-18 - Revision 1.5
W83977EF-AW /W83977EG-AW
5. FDC FUNCTIONAL DESCRIPTION
5.1 W83977EF-AW/EG FDC
The floppy disk controller of W83977EF-AW/EG integrates all of the logic required for floppy disk
control. The FDC implements a PC/AT or PS/2 solution. All programmable options default to
compatible values. The FIFO provides better system performance in multi-master systems. The
digital data separator supports up to 2 M bits/sec data rate.
The FDC includes the following blocks: AT interface, Precompensation, Data Rate Selection, Digital
Data Separator, FIFO, and FDC Core.
5.1.1 AT interface
The interface consists of the standard asynchronous signals:RD#, WR#, A0-A3, IRQ, DMA control,
and a data bus. The address lines select between the configuration registers, the FIFO and
control/status registers. This interface can be switched between PC/AT, Model 30, or PS/2 normal
modes. The PS/2 register sets are a superset of the registers found in a PC/AT.
5.1.2 FIFO (Data)
The FIFO is 16 bytes in size and has programmable threshold values. All command parameter
information and disk data transfers go through the FIFO. Data transfers are governed by the RQM and
DIO bits in the Main Status Register.
The FIFO defaults to disabled mode after any form of reset. This maintains PC/AT hardware
compatibility. The default values can be changed through the CONFIGURE command. The advantage
of the FIFO is that it allows the system a larger DMA latency without causing disk errors. The following
tables give several examples of the delays with a FIFO. The data are based upon the following
formula:
THRESHOLD # × (1/DATA/RATE) *8 - 1.5 μS = DELAY
FIFO THRESHOLD MAXIMUM DELAY TO SERVICING AT 500K BPS
Data Rate
1 Byte
1 × 16 μS - 1.5 μS = 14.5 μS
2 Byte
2 × 16 μS - 1.5 μS = 30.5 μS
8 Byte
8 × 16 μS - 1.5 μS = 6.5 μS
15 Byte 15 × 16 μS - 1.5 μS = 238.5 μS
FIFO THRESHOLD MAXIMUM DELAY TO SERVICING AT 1M BPS
Data Rate
1 Byte
1 × 8 μS - 1.5 μS = 6.5 μS
2 Byte 2 × 8 μS - 1.5 μS = 14.5 μS
8 Byte
8 × 8 μS - 1.5 μS = 62.5 μS
15 Byte
15 × 8 μS - 1.5 μS = 118.5 μS
Publication Release Date: January, 2010
-19 - Revision 1.5
W83977EF-AW /W83977EG-AW
At the start of a command the FIFO is always disabled and command parameters must be sent based
upon the RQM and DIO bit settings in the main status register. When the FDC enters the command
execution phase, it clears the FIFO of any data to ensure that invalid data are not transferred.
An overrun and underrun will terminate the current command and the data transfer. Disk writes will
complete the current sector by generating a 00 pattern and valid CRC. Reads require the host to
remove the remaining data so that the result phase may be entered.
DMA transfers are enabled with the SPECIFY command and are initiated by the FDC by activating the
DRQ pin during a data transfer command. The FIFO is enabled directly by asserting DACK# and
addresses need not be valid.
Note that if the DMA controller is programmed to function in verify mode a pseudo read is performed
by the FDC based only onDACK#. This mode is only available when the FDC has been configured
into byte mode (FIFO disabled) and is programmed to do a read. With the FIFO enabled the above
operation is performed by using the new VERIFY command. No DMA operation is needed.
5.1.3 Data Separator
The function of the data separator is to lock onto the incoming serial read data. When a lock is
achieved the serial front end logic of the chip is provided with a clock which is synchronized to the
read data. The synchronized clock, called the Data Window, is used to internally sample the serial
data portion of the bit cell, and the alternate state samples the clock portion. Serial to parallel
conversion logic separates the read data into clock and data bytes.
The Digital Data Separator (DDS) has three parts: control logic, error adjustment, and speed tracking.
The DDS circuit cycles once every 12 clock cycles ideally. Any data pulse input will be synchronized
and then adjusted by immediate error adjustment. The control logic will generate RDD and RWD for
every pulse input. During any cycle where no data pulse is present, the DDS cycles are based on
speed. A digital integrator is used to keep track of the speed changes in the input data stream.
5.1.4 Write Precompensation
The write precompensation logic is used to minimize bit shifts in the RDDATA stream from the disk
drive. Shifting of bits is a known phenomenon in magnetic media and is dependent on the disk media
and the floppy drive.
The FDC monitors the bit stream that is being sent to the drive. The data patterns that require
precompensation are well known. Depending upon the pattern, the bit is shifted either early or late
relative to the surrounding bits.
5.1.5 Perpendicular Recording Mode
The FDC is also capable of interfacing directly to perpendicular recording floppy drives. Perpendicular
recording differs from the traditional longitudinal method in that the magnetic bits are oriented
vertically. This scheme packs more data bits into the same area.
FDCs with perpendicular recording drives can read standard 3.5" floppy disks and can read and write
perpendicular media. Some manufacturers offer drives that can read and write standard and
perpendicular media in a perpendicular media drive.
Publication Release Date: January, 2010
-20 - Revision 1.5
W83977EF-AW /W83977EG-AW
A single command puts the FDC into perpendicular mode. All other commands operate as they
normally do. The perpendicular mode requires a 1 Mbps data rate for the FDC. At this data rate the
FIFO eases the host interface bottleneck due to the speed of data transfer to or from the disk.
5.1.6 FDC Core
The W83977EF-AW/EG FDC is capable of performing twenty commands. Each command is initiated
by a multi-byte transfer from the microprocessor. The result can also be a multi-byte transfer back to
the microprocessor. Each command consists of three phases: command, execution, and result.
Command
The microprocessor issues all required information to the controller to perform a specific operation.
Execution
The controller performs the specified operation.
Result
After the operation is completed, status information and other housekeeping information is provided to
the microprocessor.
5.1.7 FDC Commands
Command Symbol Descriptions:
C: Cylinder number 0 - 256
D: Data Pattern
DIR: Step Direction
DIR = 0, step out
DIR = 1, step in
DS0: Disk Drive Select 0
DS1: Disk Drive Select 1
DTL: Data Length
EC: Enable Count
EOT: End of Track
EFIFO: Enable FIFO
EIS: Enable Implied Seek
EOT: End of track
FIFOTHR: FIFO Threshold
Publication Release Date: January, 2010
-21 - Revision 1.5
W83977EF-AW /W83977EG-AW
GAP: Gap length selection
GPL: Gap Length
H: Head number
HDS: Head number select
HLT: Head Load Time
HUT: Head Unload Time
LOCK: Lock EFIFO, FIFOTHR, PTRTRK bits prevent affected by software reset
MFM: MFM or FM Mode
MT: Multitrack
N: The number of data bytes written in a sector
NCN: New Cylinder Number
ND: Non-DMA Mode
OW: Overwritten
PCN: Present Cylinder Number
POLL: Polling Disable
PRETRK: Precompensation Start Track Number
R: Record
RCN: Relative Cylinder Number
R/W: Read/Write
SC: Sector/per cylinder
SK: Skip deleted data address mark
SRT: Step Rate Time
ST0: Status Register 0
ST1: Status Register 1
ST2: Status Register 2
ST3: Status Register 3
WG: Write gate alters timing of WE
Publication Release Date: January, 2010
-22 - Revision 1.5
W83977EF-AW /W83977EG-AW
(1) Read Data
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W MT MFM SK 0 0 1 1 0 Command codes
W 0 0 0 0 0 HDS DS1 DS0
W ---------------------- C ------------------------ Sector ID information prior
to command execution
W ---------------------- H ------------------------
W ---------------------- R ------------------------
W ---------------------- N ------------------------
W -------------------- EOT -----------------------
W -------------------- GPL -----------------------
W -------------------- DTL -----------------------
Execution Data transfer between the
FDD and system
Result R -------------------- ST0 ----------------------- Status information after
R command execution
-------------------- ST1 -----------------------
R
-------------------- ST2 -----------------------
R ---------------------- C ------------------------ Sector ID information after
command execution
R ---------------------- H ------------------------
R ---------------------- R ------------------------
R ---------------------- N ------------------------
Publication Release Date: January, 2010
-23 - Revision 1.5
W83977EF-AW /W83977EG-AW
(2) Read Deleted Data
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W MT MFM SK 0 1 1 0 0 Command codes
W 0 0 0 0 0 HDS DS1 DS0
W ---------------------- C ------------------------ Sector ID information prior
to command execution
W ---------------------- H ------------------------
W ---------------------- R ------------------------
W ---------------------- N ------------------------
W -------------------- EOT -----------------------
W -------------------- GPL -----------------------
W -------------------- DTL -----------------------
Execution Data transfer between the
FDD and system
Result R -------------------- ST0 ----------------------- Status information after
command execution
R -------------------- ST1 -----------------------
R -------------------- ST2 -----------------------
R ---------------------- C ------------------------ Sector ID information after
command execution
R ---------------------- H ------------------------
R ---------------------- R ------------------------
R ---------------------- N ------------------------
Publication Release Date: January, 2010
-24 - Revision 1.5
W83977EF-AW /W83977EG-AW
(3) Read A Track
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 MFM 0 0 0 0 1 0 Command codes
W 0 0 0 0 0 HDS DS1 DS0
W ---------------------- C ------------------------ Sector ID information prior
to command execution
W ---------------------- H ------------------------
W ---------------------- R ------------------------
W ---------------------- N ------------------------
W -------------------- EOT -----------------------
W -------------------- GPL -----------------------
W -------------------- DTL -----------------------
Execution Data transfer between the
FDD and system; FDD
reads contents of all
cylinders from index hole to
EOT
Result R -------------------- ST0 ----------------------- Status information after
command execution
R -------------------- ST1 -----------------------
R -------------------- ST2 -----------------------
R ---------------------- C ------------------------ Sector ID information after
command execution
R ---------------------- H ------------------------
R ---------------------- R ------------------------
R ---------------------- N ------------------------
Publication Release Date: January, 2010
-25 - Revision 1.5
W83977EF-AW /W83977EG-AW
(4) Read ID
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 MFM 0 0 1 0 1 0 Command codes
W 0 0 0 0 0 HDS DS1 DS0
Execution The first correct ID
information on the cylinder
is stored in Data Register
Result R -------------------- ST0 ----------------------- Status information after
command execution
R -------------------- ST1 -----------------------
R -------------------- ST2 -----------------------
R ---------------------- C ------------------------ Disk status after the
R command has been
---------------------- H ------------------------
completed
R
---------------------- R ------------------------
R
---------------------- N ------------------------
(5) Verify
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W MT MFM SK 1 0 1 1 0 Command codes
W EC 0 0 0 0 HDS DS1 DS0
W ---------------------- C ------------------------ Sector ID information prior
to command execution
W ---------------------- H ------------------------
W ---------------------- R ------------------------
W ---------------------- N ------------------------
W -------------------- EOT -----------------------
W -------------------- GPL -----------------------
-------------------- DTL/SC -------------------
Execution No data transfer takes
place
Result R -------------------- ST0 ----------------------- Status information after
command execution
R -------------------- ST1 -----------------------
R -------------------- ST2 -----------------------
R ---------------------- C ------------------------ Sector ID information after
command execution
R ---------------------- H ------------------------
R ---------------------- R ------------------------
R ---------------------- N ------------------------
Publication Release Date: January, 2010
-26 - Revision 1.5
W83977EF-AW /W83977EG-AW
(6) Version
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 0 0 1 0 0 0 0 Command code
Result R 1 0 0 1 0 0 0 0 Enhanced controller
(7) Write Data
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W MT MFM 0 0 0 1 0 1 Command codes
W 0 0 0 0 0 HDS DS1 DS0
W ---------------------- C ------------------------ Sector ID information prior
to Command execution
W ---------------------- H ------------------------
W ---------------------- R ------------------------
W ---------------------- N ------------------------
W -------------------- EOT -----------------------
W -------------------- GPL -----------------------
W -------------------- DTL -----------------------
Execution Data transfer between the
FDD and system
Result R -------------------- ST0 ----------------------- Status information after
Command execution
R -------------------- ST1 -----------------------
R -------------------- ST2 -----------------------
R ---------------------- C ------------------------ Sector ID information after
Command execution
R ---------------------- H ------------------------
R ---------------------- R ------------------------
R ---------------------- N ------------------------
Publication Release Date: January, 2010
-27 - Revision 1.5
W83977EF-AW /W83977EG-AW
(8) Write Deleted Data
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W MT MFM 0 0 1 0 0 1 Command codes
W 0 0 0 0 0 HDS DS1 DS0
W ---------------------- C ------------------------ Sector ID information prior
to command execution
W ---------------------- H ------------------------
W ---------------------- R ------------------------
W ---------------------- N ------------------------
W -------------------- EOT -----------------------
W -------------------- GPL -----------------------
W -------------------- DTL -----------------------
Execution Data transfer between the
FDD and system
Result R -------------------- ST0 ----------------------- Status information after
command execution
R -------------------- ST1 -----------------------
R -------------------- ST2 -----------------------
R ---------------------- C ------------------------ Sector ID information after
command execution
R ---------------------- H ------------------------
R ---------------------- R ------------------------
R ---------------------- N ------------------------
Publication Release Date: January, 2010
-28 - Revision 1.5
W83977EF-AW /W83977EG-AW
(9) Format A Track
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 MFM 0 0 1 1 0 1 Command codes
W 0 0 0 0 0 HDS DS1 DS0
W ---------------------- N ------------------------ Bytes/Sector
W --------------------- SC ----------------------- Sectors/Cylinder
W --------------------- GPL --------------------- Gap 3
W ---------------------- D ------------------------ Filler Byte
Execution W ---------------------- C ------------------------ Input Sector Parameters
for Each
W ---------------------- H ------------------------
Sector
W ---------------------- R ------------------------
Repeat:
W ---------------------- N ------------------------
Result R -------------------- ST0 ----------------------- Status information after
command execution
R -------------------- ST1 -----------------------
R -------------------- ST2 -----------------------
R ---------------- Undefined -------------------
R
---------------- Undefined -------------------
R
---------------- Undefined -------------------
R
---------------- Undefined -------------------
(10) Recalibrate
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 0 0 0 0 1 1 1 Command codes
W 0 0 0 0 0 0 DS1 DS0
Execution Head retracted to Track 0
Interrupt
Publication Release Date: January, 2010
-29 - Revision 1.5
W83977EF-AW /W83977EG-AW
(11) Sense Interrupt Status
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 0 0 0 1 0 0 0 Command code
Result R ---------------- ST0 ------------------------- Status information at the end
of each seek operation
R ---------------- PCN -------------------------
(12) Specify
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 0 0 0 0 0 1 1 Command codes
W | ---------SRT ----------- | --------- HUT ---------- |
W |------------ HLT ----------------------------------| ND
(13) Seek
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 0 0 0 1 1 1 1 Command codes
W 0 0 0 0 0 HDS DS1 DS0
W -------------------- NCN -----------------------
Execution R Head positioned over proper
cylinder on diskette
(14) Configure
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 0 0 1 0 0 1 1 Configure information
W 0 0 0 0 0 0 0 0
W 0 EIS EFIFO POLL | ------ FIFOTHR ----|
W | --------------------PRETRK ----------------------- |
Execution Internal registers written
Publication Release Date: January, 2010
-30 - Revision 1.5
W83977EF-AW /W83977EG-AW
(15) Relative Seek
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 1 DIR 0 0 1 1 1 1 Command codes
W 0 0 0 0 0 HDS DS1 DS0
W | -------------------- RCN ---------------------------- |
(16) Dumpreg
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 0 0 0 1 1 1 0 Registers placed in FIFO
Result R ----------------------- PCN-Drive 0--------------------
R ----------------------- PCN-Drive 1 -------------------
R ----------------------- PCN-Drive 2--------------------
R ----------------------- PCN-Drive 3 -------------------
R --------SRT ------------------ | --------- HUT --------
R ----------- HLT -----------------------------------| ND
R ------------------------ SC/EOT ----------------------
R LOCK 0 D3 D2 D1 D0 GAP WG
R 0 EIS EFIFO POLL | ------ FIFOTHR --------
R -----------------------PRETRK -------------------------
(17) Perpendicular Mode
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 0 0 1 0 0 1 0 Command Code
W OW 0 D3 D2 D1 D0 GAP WG
(18) Lock
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W LOCK 0 0 1 0 1 0 0 Command Code
Result R 0 0 0 LOCK 0 0 0 0
Publication Release Date: January, 2010
-31 - Revision 1.5
W83977EF-AW /W83977EG-AW
(19) Sense Drive Status
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W 0 0 0 0 0 1 0 0 Command Code
W 0 0 0 0 0 HDS DS1 DS0
Result R ---------------- ST3 ------------------------- Status information about
disk drive
(20) Invalid
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command W ------------- Invalid Codes ----------------- Invalid codes (no
operation- FDC goes to
standby state)
Result R -------------------- ST0 ---------------------- ST0 = 80H
Publication Release Date: January, 2010
-32 - Revision 1.5
W83977EF-AW /W83977EG-AW
5.2 Register Descriptions
There are several status, data, and control registers in W83977EF-AW. These registers are defined
below:
ADDRESS REGISTER
OFFSET READ WRITE
base address + 0 SA REGISTER
base address + 1 SB REGISTER
base address + 2 DO REGISTER
base address + 3 TD REGISTER TD REGISTER
base address + 4 MS REGISTER DR REGISTER
base address + 5 DT (FIFO) REGISTER DT (FIFO) REGISTER
base address + 7 DI REGISTER CC REGISTER
5.2.1 Status Register A (SA Register) (Read base address + 0)
This register is used to monitor several disk interface pins in PS/2 and Model 30 modes. In PS/2 mode,
the bit definitions for this register are as follows:
2
1
7 6 5 4 3 0
DIR
WP#
INDEX#
HEAD
TRAK0#
STEP
DRV2#
INIT PENDING
INIT PENDING (Bit 7):
This bit indicates the value of the floppy disk interrupt output.
DRV2# (Bit 6):
0 A second drive has been installed
1 A second drive has not been installed
STEP (Bit 5):
This bit indicates the complement of STEP# output.
TRAK0#(Bit 4):
This bit indicates the value of TRAK0# input.
HEAD (Bit 3):
This bit indicates the complement of HEAD# output.
Publication Release Date: January, 2010
-33 - Revision 1.5
W83977EF-AW /W83977EG-AW
0 side 0
1 side 1
INDEX#(Bit 2):
This bit indicates the value of INDEX# output.
WP#(Bit 1):
0 disk is write-protected
1 disk is not write-protected
DIR (Bit 0)
This bit indicates the direction of head movement.
0 outward direction
1 inward direction
In PS/2 Model 30 mode, the bit definitions for this register are as follows:
2
1
7 6 5 4 3 0
DIR#
WP
INDEX
HEAD#
TRAK0
STEP F/F
DRQ
INIT PENDING
INIT PENDING (Bit 7):
This bit indicates the value of the floppy disk interrupt output.
DRQ (Bit 6):
This bit indicates the value of DRQ output pin.
STEP F/F (Bit 5):
This bit indicates the complement of latched STEP# output.
TRAK0 (Bit 4):
This bit indicates the complement of TRAK0# input.
HEAD# (Bit 3):
This bit indicates the value of HEAD# output.
0 side 1
1 side 0
INDEX (Bit 2):
This bit indicates the complement of INDEX# output.
Publication Release Date: January, 2010
-34 - Revision 1.5
W83977EF-AW /W83977EG-AW
WP (Bit 1):
0 disk is not write-protected
1 disk is write-protected
DIR#(Bit 0)
This bit indicates the direction of head movement.
0 inward direction
1 outward direction
5.2.2 Status Register B (SB Register) (Read base address + 1)
This register is used to monitor several disk interface pins in PS/2 and Model 30 modes. In PS/2 mode,
the bit definitions for this register are as follows:
2
1
7 6 5 4 3
0
1
1
MOT EN A
MOT EN B
WE
RDATA Toggle
WDATA Toggle
Drive SEL0
Drive SEL0 (Bit 5):
This bit indicates the status of DO REGISTER bit 0 (drive select bit 0).
WDATA Toggle (Bit 4):
This bit changes state at every rising edge of the WD# output pin.
RDATA Toggle (Bit 3):
This bit changes state at every rising edge of the RDATA# output pin.
WE (Bit 2):
This bit indicates the complement of the WE# output pin.
MOT EN B (Bit 1)
This bit indicates the complement of the MOB# output pin.
MOT EN A (Bit 0)
This bit indicates the complement of the MOA# output pin.
In PS/2 Model 30 mode, the bit definitions for this register are as follows:
Publication Release Date: January, 2010
-35 - Revision 1.5
W83977EF-AW /W83977EG-AW
2
1
7 6 5 4 3
0
DSC#
DSD#
WE F/F
RDATA F/F
WD F/F
DSA#
DSB#
DRV2#
DRV2# (Bit 7):
0 A second drive has been installed
1 A second drive has not been installed
DSB# (Bit 6):
This bit indicates the status of DSB# output pin.
DSA# (Bit 5):
This bit indicates the status of DSA# output pin.
WD F/F(Bit 4):
This bit indicates the complement of the latched WD# output pin at every rising edge of the WD#
output pin.
RDATA F/F(Bit 3):
This bit indicates the complement of the latched RDATA# output pin .
WE F/F (Bit 2):
This bit indicates the complement of latched WE# output pin.
DSD# (Bit 1):
0 Drive D has been selected
1 Drive D has not been selected
DSC# (Bit 0):
0 Drive C has been selected
1 Drive C has not been selected
Publication Release Date: January, 2010
-36 - Revision 1.5
W83977EF-AW /W83977EG-AW
5.2.3 Digital Output Register (DO Register) (Write base address + 2)
The Digital Output Register is a write-only register controlling drive motors, drive selection, DRQ/IRQ
enable, and FDC resetting. All the bits in this register are cleared by the MR pin. The bit definitions are
as follows:
76 3 1-0
54 2
Drive Select: 00 select drive A
01 select drive B
10 select drive C
11 select drive D
Floppy Disk Controller Reset
Active low resets FDC
DMA and INT Enable
Active high enable DRQ/IRQ
Motor Enable A. Motor A on when active high
Motor Enable B. Motor B on when active high
Motor Enable C. Motor C on when active high
Motor Enable D. Motor D on when active high
5.2.4 Tape Drive Register (TD Register) (Read base address + 3)
This register is used to assign a particular drive number to the tape drive support mode of the data
separator. This register also holds the media ID, drive type, and floppy boot drive information of the
floppy disk drive. In normal floppy mode, this register includes only bit 0 and 1. The bit definitions are
as follows:
2
7 6 5 4 3 1
0
XX X X
XX
Tape sel 0
Tape sel 1
If three mode FDD function is enabled (EN3MODE = 1 in CR9), the bit definitions are as follows:
2
1
7 6 5 4 3
0
Tape Sel 0
Tape Sel 1
Floppy boot drive 0
Floppy boot drive 1
Drive type ID0
Drive type ID1
Media ID0
Media ID1
Publication Release Date: January, 2010
-37 - Revision 1.5
W83977EF-AW /W83977EG-AW
Media ID1 Media ID0 (Bit 7, 6):
These two bits are read only. These two bits reflect the value of CR8 bit 3, 2.
Drive type ID1 Drive type ID0 (Bit 5, 4):
These two bits reflect two of the bits of CR7. Which two bits are reflected depends on the last drive
selected in the DO REGISTER.
Floppy Boot drive 1, 0 (Bit 3, 2):
These two bits reflect the value of CR8 bit 1, 0.
Tape Sel 1, Tape Sel 0 (Bit 1, 0):
These two bits assign a logical drive number to the tape drive. Drive 0 is not available as a tape drive
and is reserved as the floppy disk boot drive.
TAPE SEL 1 TAPE SEL 0 DRIVE SELECTED
0 0 None
0 1 1
1 0 2
1 1 3
5.2.5 Main Status Register (MS Register) (Read base address + 4)
The Main Status Register is used to control the flow of data between the microprocessor and the
controller. The bit definitions for this register are as follows:
6 0
7 5 4 32 1
FDD 0 Busy, (D0B = 1), FDD number 0 is in the SEEK mode.
FDD 1 Busy, (D1B = 1), FDD number 1 is in the SEEK mode.
FDD 2 Busy, (D2B = 1), FDD number 2 is in the SEEK mode.
FDD 3 Busy, (D3B = 1), FDD number 3 is in the SEEK mode.
FDC Busy, (CB). A read or write command is in the process when CB = HIGH.
Non-DMA mode, the FDC is in the non-DMA mode, this bit is set only during the
execution phase in non-DMA mode.
Transition to LOW state indicates execution phase has ended.
DATA INPUT/OUTPUT, (DIO). If DIO= HIGH then transfer is from Data Register to the processor.
If DIO = LOW then transfer is from processor to Data Register.
Request for Master (RQM). A high on this bit indicates Data Register is ready to send or receive data to or from the processor.
5.2.6 Data Rate Register (DR Register) (Write base address + 4)
The Data Rate Register is used to set the transfer rate and write precompensation. The data rate of
the FDC is programmed by the CC REGISTER for PC-AT and PS/2 Model 30 and PS/2 mode, and
not by the DR REGISTER. The real data rate is determined by the most recent write to either of the
DR REGISTER or CC REGISTER.
Publication Release Date: January, 2010
-38 - Revision 1.5
W83977EF-AW /W83977EG-AW
1
7 6 5 4 3 2
0
0
DRATE0
DRATE1
PRECOMP0
PRECOMP1
PRECOMP2
POWER DOWN
S/W RESET
S/W RESET (Bit 7):
This bit is the software reset bit.
POWER-DOWN (Bit 6):
0 FDC in normal mode
1 FDC in power-down mode
PRECOMP2 PRECOMP1 PRECOMP0 (Bit 4, 3, 2):
These three bits select the value of write precompensation. The following tables show the
precompensation values for the combination of these bits.
PRECOMP PRECOMPENSATION DELAY
2 1 0 250K - 1 Mbps 2 Mbps Tape drive
0 0 0 Default Delays Default Delays
0 0 1 41.67 nS 20.8 nS
0 1 0 83.34 nS 41.17 nS
0 1 1 125.00 nS 62.5nS
1 0 0 166.67 nS 83.3 nS
1 0 1 208.33 nS 104.2 nS
1 1 0 250.00 nS 125.00 nS
1 1 1 0.00 nS (disabled) 0.00 nS (disabled)
DATA RATE DEFAULT PRECOMPENSATION DELAYS
250 KB/S 125 nS
300 KB/S 125 nS
500 KB/S 125 nS
1 MB/S 41.67nS
2 MB/S 20.8 nS
Publication Release Date: January, 2010
-39 - Revision 1.5
W83977EF-AW /W83977EG-AW
DRATE1 DRATE0 (Bit 1, 0):
These two bits select the data rate of the FDC and reduced write current control.
00 500 KB/S (MFM), 250 KB/S (FM), RWC#= 1
01 300 KB/S (MFM), 150 KB/S (FM), RWC#= 0
10 250 KB/S (MFM), 125 KB/S (FM), RWC#= 0
11 1 MB/S (MFM), Illegal (FM), RWC#= 1
The 2 MB/S data rate for Tape drive is only supported by setting 01 to DRATE1 and DRATE0 bits, as
well as setting 10 to DRT1 and DRT0 bits which are two of the Configure Register CRF4 or CRF5 bits
in logic device 0. Please refer to the function description of CRF4 or CRF5 and data rate table for
individual data rates setting.
5.2.7 FIFO Register (R/W base address + 5)
The Data Register consists of four status registers in a stack with only one register presented to the
data bus at a time. This register stores data, commands, and parameters and provides diskette-drive
status information. Data bytes are passed through the data register to program or obtain results after
a command. In the W83977EF-AW/EG, this register defaults to FIFO disabled mode after reset. The
FIFO can change its value and enable its operation through the CONFIGURE command.
Status Register 0 (ST0)
7-6 5 3 2 1-0
4
US1, US0 Drive Select:
00 Drive A selected
01 Drive B selected
10 Drive C selected
11 Drive D selected
HD Head address:
1 Head selected
0 Head selected
NR Not Ready:
1 Drive is not ready
0 Drive is ready
EC Equipment Check:
1 When a fault signal is received from the FDD or the track
0 signal fails to occur after 77 step pulses
0 No error
SE Seek end:
1 seek end
0 seek error
IC Interrupt Code:
00 Normal termination of command
01 Abnormal termination of command
10 Invalid command issue
11 Abnormal termination because the ready signal from FDD changed state during command executio
Publication Release Date: January, 2010
-40 - Revision 1.5
W83977EF-AW /W83977EG-AW
Status Register 1 (ST1)
7 6 5 4 3 2
1 0
Missing Address Mark. 1 When the FDC cannot detect the data address mark
or the data address mark has been deleted.
NW (Not Writable). 1 If a write Protect signal is detected from the diskette drive during
execution of write data.
ND (No DATA). 1 If specified sector cannot be found during execution of a read, write or verifly data.
Not used. This bit is always 0.
OR (Over Rum). 1 If the FDC is not serviced by the host system within a certain time interval during data transfer.
DE (data Error).1 When the FDC detects a CRC error in either the ID field or the data field.
Not used. This bit is always 0.
EN (End of track). 1 When the FDC tries to access a sector beyond the final sector of a cylinder.
Status Register 2 (ST2)
70 4 3 2 1
6 5
MD (Missing Address Mark in Data Field).
1 If the FDC cannot find a data address mark
(or the address mark has been deleted)
when reading data from the media
0 No error
BC (Bad Cylinder)
1 Bad Cylinder
0 No error
SN (Scan Not satisfied)
1 During execution of the Scan command
0 No error
SH (Scan Equal Hit)
1 During execution of the Scan command, if the equal condition is satisfied
0 No error
WC (Wrong Cylinder)
1 Indicates wrong Cylinder
DD (Data error in the Data field)
1 If the FDC detects a CRC error in the data field
0 No error
CM (Control Mark)
1 During execution of the read data or scan command
0 No error
Not used. This bit is always 0
Status Register 3 (ST3)
7 6 5 4 3 2 1 0
US0 Unit Select 0
US1 Unit Select 1
HD Head Address
TS Two-Side
TO Track 0
RY Ready
WP Write Protected
FT Fault
Publication Release Date: January, 2010
-41 - Revision 1.5
W83977EF-AW /W83977EG-AW
5.2.8 Digital Input Register (DI Register) (Read base address + 7)
The Digital Input Register is an 8-bit read-only register used for diagnostic purposes. In a PC/XT or AT
only Bit 7 is checked by the BIOS. When the register is read, Bit 7 shows the complement
ofDSKCHG#, while other bits of the data bus remain in tri-state. Bit definitions are as follows:
7 6 5
4 3 2 1 0
x x x x x x
x
Reserved for the hard disk controller
x
During a read of this register, these bits are in tri-stat
DSKCHG
In the PS/2 mode, the bit definitions are as follows:
7 6 5 4 3
2 1 0
11 1 1
HIGH DENS#
DRATE0
DRATE1
DSKCHG
DSKCHG (Bit 7):
This bit indicates the complement of the DSKCHG# input.
Bit 6-3: These bits are always a logic 1 during a read.
DRATE1 DRATE0 (Bit 2, 1):
These two bits select the data rate of the FDC. Refer to the DR register bits 1 and 0 for the settings
corresponding to the individual data rates.
HIGHDENS#(Bit 0):
0 500 KB/S or 1 MB/S data rate (high density FDD)
1 250 KB/S or 300 KB/S data rate
Publication Release Date: January, 2010
-42 - Revision 1.5
W83977EF-AW /W83977EG-AW
In the PS/2 Model 30 mode, the bit definitions are as follows:
7 6 5 4 3 2
1 0
0 00
DRATE0
DRATE1
NOPREC
DMAEN
DSKCHG#
DSKCHG (Bit 7):
This bit indicates the status of DSKCHG# input.
Bit 6-4: These bits are always a logic 1 during a read.
DMAEN (Bit 3):
This bit indicates the value of DO REGISTER bit 3.
NOPREC (Bit 2):
This bit indicates the value of CC REGISTER NOPREC bit.
DRATE1 DRATE0 (Bit 1, 0):
These two bits select the data rate of the FDC.
5.2.9 Configuration Control Register (CC Register) (Write base address + 7)
This register is used to control the data rate. In the PC/AT and PS/2 mode, the bit definitions are as
follows:
4 2
6 5 3 1
7 0
xx x x x x
DRATE0
DRATE1
X: Reserved
Bit 7-2: Reserved. These bits should be set to 0.
DRATE1 DRATE0 (Bit 1, 0):
These two bits select the data rate of the FDC.
In the PS/2 Model 30 mode, the bit definitions are as follows:
Publication Release Date: January, 2010
-43 - Revision 1.5
W83977EF-AW /W83977EG-AW
2
1
7 6 5 4 3 0
XX X
XX
DRATE0
DRATE1
NOPREC
X: Reserved
Bit 7-3: Reserved. These bits should be set to 0.
NOPREC (Bit 2):
This bit indicates no precompensation. It has no function and can be set by software.
DRATE1 DRATE0 (Bit 1, 0):
These two bits select the data rate of the FDC.
Publication Release Date: January, 2010
-44 - Revision 1.5
W83977EF-AW /W83977EG-AW
6. UART PORT
6.1 Universal Asynchronous Receiver/Transmitter (UART A, UART B)
The UARTs are used to convert parallel data into serial format on the transmit side and convert serial
data to parallel format on the receiver side. The serial format, in order of transmission and reception,
is a start bit, followed by five to eight data bits, a parity bit (if programmed) and one, one and half (five-
bit format only) or two stop bits. The UARTs are capable of handling divisors of 1 to 65535 and
producing a 16x clock for driving the internal transmitter logic. Provisions are also included to use this
16x clock to drive the receiver logic. The UARTs also support the MIDI data rate. Furthermore, the
UARTs also include complete modem control capability and a processor interrupt system that may be
software trailed to the computing time required to handle the communication link. The UARTs have a
FIFO mode to reduce the number of interrupts presented to the CPU. In each UART, there are 16-
byte FIFOs for both receive and transmit mode.
6.2 Register Address
6.2.1 UART Control Register (UCR) (Read/Write)
The UART Control Register controls and defines the protocol for asynchronous data communications,
including data length, stop bit, parity, and baud rate selection.
5 4 2
7 6 3 1 0
Data length select bit 0 (DLS0)
Data length select bit 1(DLS1)
Multiple stop bits enable (MSBE)
Parity bit enable (PBE)
Even parity enable (EPE)
Parity bit fixed enable (PBFE)
Set silence enable (SSE)
Baudrate divisor latch access bit (BDLAB)
Bit 7: BDLAB. When this bit is set to a logical 1, designers can access the divisor (in 16-bit binary
format) from the divisor latches of the baudrate generator during a read or write operation.
When this bit is reset, the Receiver Buffer Register, the Transmitter Buffer Register, or the
Interrupt Control Register can be accessed.
Bit 6: SSE. A logical 1 forces the Serial Output (SOUT) to a silent state (a logical 0). Only IRTX is
affected by this bit; the transmitter is not affected.
Bit 5: PBFE. When PBE and PBFE of UCR are both set to a logical 1,
(1) if EPE is logical 1, the parity bit is fixed as logical 0 to transmit and check.
(2) if EPE is logical 0, the parity bit is fixed as logical 1 to transmit and check.
Publication Release Date: January, 2010
-45 - Revision 1.5
W83977EF-AW /W83977EG-AW
TABLE 6-1 UART Register Bit Map
Bit Number
Register Address Base 0 1 2 3 4 5 6 7
+ 0 Receiver RBR RX Data RX Data RX Data RX Data RX Data RX Data RX Data RX Data
Buffer
BDLAB = 0 Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7
Register
(Read Only)
+ 0 Transmitter TBR TX Data TX Data TX Data TX Data TX Data TX Data TX Data TX Data
Buffer Register
BDLAB = 0 Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7
(Write Only)
+ 1 Interrupt Control ICR RBR Data TBR USR HSR 0 0 0 0
Register Ready Empty Interrupt Interrupt
BDLAB = 0
Interrupt Interrupt Enable Enable
Enable Enable
(EUSRI) (EHSRI)
(ERDRI) (ETBREI)
+ 2 Interrupt Status ISR "0" if Interrupt Interrupt Interrupt 0 0 FIFOs FIFOs
Register Interrupt Status Status Status
Enabled Enabled
(Read Only) Pending
Bit (0) Bit (1) Bit (2)**
** **
+ 2 UART FIFO UFR FIFO RCVR XMIT DMA Reserved Reversed RX RX
Control Enable FIFO FIFO Mode Interrupt Interrupt
Register Reset Reset Select Active Level Active Level
(Write Only) (LSB) (MSB)
+ 3 UART Control UCR Data Data Multiple Parity Even Parity Set Baudrate
Register Length Length Stop Bits Bit Parity Bit Fixed Silence Divisor
Select Select Enable Enable Enable Enable Enable Latch
Bit 0 Bit 1 Access Bit
(MSBE) (PBE) (EPE) PBFE) (SSE)
(DLS0) (DLS1)
(BDLAB)
+ 4 Handshake HCR Data Request Loopback IRQ Internal 0 0 0
Control Terminal to RI Enable Loopback
Register Ready Send Input Enable
(DTR) (RTS)
+ 5 UART Status USR RBR Data Overrun Parity Bit No Stop
Silent TBR TSR RX FIFO
Register Ready Error Error Bit Byte Empty Empty Error
Error Detected Indication
(RDR) (OER) (PBER) (TBRE) (TSRE)
(NSER) (SBD) (RFEI) **
+ 6 Handshake HSR CTS DSR RI Falling DCD Clear Data Set Ring Data Carrier
Status Register Toggling Toggling Edge Toggling to Send Ready Indicator Detect
(DCD)
(TCTS) (TDSR) (FERI) (TDCD) (CTS) (DSR) (RI)
+ 7 User Defined UDR Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7
Register
+ 0 Baudrate BLL Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7
Divisor Latch
BDLAB = 1
Low
+ 1 Baudrate BHL Bit 8 Bit 9 Bit 10 Bit 11 Bit 12 Bit 13 Bit 14 Bit 15
Divisor Latch
BDLAB = 1
High
*: Bit 0 is the least significant bit. The least significant bit is the first bit serially transmitted or received.
**: These bits are always 0 in 16450 Mode.
Publication Release Date: January, 2010
-46 - Revision 1.5
W83977EF-AW /W83977EG-AW
Bit 4: EPE. This bit describes the number of logic 1's in the data word bits and parity bit only when bit
3 is programmed. When this bit is set, an even number of logic 1's are sent or checked. When
the bit is reset, an odd number of logic 1's are sent or checked.
Bit 3: PBE. When this bit is set, the position between the last data bit and the stop bit of the SOUT will
be stuffed with the parity bit at the transmitter. For the receiver, the parity bit in the same
position as the transmitter will be detected.
Bit 2: MSBE. This bit defines the number of stop bits in each serial character that is transmitted or
received.
(1) If MSBE is set to a logical 0, one stop bit is sent and checked.
(2) If MSBE is set to a logical 1, and data length is 5 bits, one and a half stop bits are sent and
checked.
(3) If MSBE is set to a logical 1, and data length is 6, 7, or 8 bits, two stop bits are sent and
checked.
Bits 0 and 1: DLS0, DLS1. These two bits define the number of data bits that are sent or checked in
each serial character.
TABLE 6-2 WORD LENGTH DEFINITION
DLS1 DLS0 DATA LENGTH
0 0 5 bits
0 1 6 bits
1 0 7 bits
1 1 8 bits
Publication Release Date: January, 2010
-47 - Revision 1.5
W83977EF-AW /W83977EG-AW
6.2.2 UART Status Register (USR) (Read/Write)
This 8-bit register provides information about the status of the data transfer during communication.
2
70 6 4 3 1
5
RBR Data ready (RDR)
Overrun error (OER)
Parity bit error (PBER)
No stop bit error (NSER)
Silent byte detected (SBD)
Transmitter Buffer Register empty (TBRE)
Transmitter Shift Register empty (TSRE)
RX FIFO Error Indication (RFEI)
Bit 7: RFEI. In 16450 mode, this bit is always set to a logic 0. In 16550 mode, this bit is set to a logic 1
when there is at least one parity bit error, no stop bit error or silent byte detected in the FIFO. In
16550 mode, this bit is cleared by reading from the USR if there are no remaining errors left in
the FIFO.
Bit 6: TSRE. In 16450 mode, when TBR and TSR are both empty, this bit will be set to a logical 1. In
16550 mode, if the transmit FIFO and TSR are both empty, it will be set to a logical 1. Other
thanthese two cases, this bit will be reset to a logical 0.
Bit 5: TBRE. In 16450 mode, when a data character is transferred from TBR to TSR, this bit will be set
to a logical 1. If ETREI of ICR is a logical 1, an interrupt will be generated to notify the CPU to
write the next data. In 16550 mode, this bit will be set to a logical 1 when the transmit FIFO is
empty. It will be reset to a logical 0 when the CPU writes data into TBR or FIFO.
Bit 4: SBD. This bit is set to a logical 1 to indicate that received data are kept in silent state for a full
word time, including start bit, data bits, parity bit, and stop bits. In 16550 mode, it indicates the
same condition for the data on top of the FIFO. When the CPU reads USR, it will clear this bit to
a logical 0.
Bit 3: NSER. This bit is set to a logical 1 to indicate that the received data have no stop bit. In 16550
mode, it indicates the same condition for the data on top of the FIFO. When the CPU reads
USR, it will clear this bit to a logical 0.
Bit 2: PBER. This bit is set to a logical 1 to indicate that the parity bit of received data is wrong. In
16550 mode, it indicates the same condition for the data on top of the FIFO. When the CPU
reads USR, it will clear this bit to a logical 0.
Bit 1: OER. This bit is set to a logical 1 to indicate received data have been overwritten by the next
received data before they were read by the CPU. In 16550 mode, it indicates the same
condition instead of FIFO full. When the CPU reads USR, it will clear this bit to a logical 0.
Bit 0: RDR. This bit is set to a logical 1 to indicate received data are ready to be read by the CPU in
the RBR or FIFO. After no data are left in the RBR or FIFO, the bit will be reset to a logical 0.
6.2.3 Handshake Control Register (HCR) (Read/Write)
Publication Release Date: January, 2010
-48 - Revision 1.5
W83977EF-AW /W83977EG-AW
This register controls the pins of the UART used for handshaking peripherals such as modem, and
controls the diagnostic mode of the UART.
7 5 4 3 2 1 0
6
0
0 0
Data terminal ready (DTR)
Request to send (RTS)
Loopback RI input
IRQ enable
Internal loopback enable
Bit 4: When this bit is set to a logical 1, the UART enters diagnostic mode by an internal loopback, as
follows:
(1) SOUT is forced to logical 1, and SIN is isolated from the communication link instead of the
TSR.
(2) Modem output pins are set to their inactive state.
(3) Modem input pins are isolated from the communication link and connect internally as DTR
(bit 0 of HCR) →DSR#, RTS ( bit 1 of HCR) →CTS#, Loopback RI input ( bit 2 of HCR) →
RI#and IRQ enable ( bit 3 of HCR) →DCD#.
Aside from the above connections, the UART operates normally. This method allows the
CPU to test the UART in a convenient way.
Bit 3: The UART interrupt output is enabled by setting this bit to a logic 1. In the diagnostic mode this
bit is internally connected to the modem control input DCD#.
Bit 2: This bit is used only in the diagnostic mode. In the diagnostic mode this bit is internally
connected to the modem control input RI#.
Bit 1: This bit controls the RTS# output. The value of this bit is inverted and output to RTS#.
Bit 0: This bit controls the DTR# output. The value of this bit is inverted and output to DTR#.
6.2.4 Handshake Status Register (HSR) (Read/Write)
This register reflects the current state of four input pins for handshake peripherals such as a modem
and records changes on these pins.
70 6 5 4 3 2 1
toggling (TCTS)
CTS#
toggling (TDSR)
DSR#
RI falling edge (FERI)
toggling (TDCD)
DCD#
Clear to send (CTS)
Data set ready (DSR)
Ring indicator (RI)
Data carrier detect (DCD)
Publication Release Date: January, 2010
-49 - Revision 1.5
W83977EF-AW /W83977EG-AW
Bit 7: This bit is the opposite of the DCD# input. This bit is equivalent to bit 3 of HCR in loopback
mode.
Bit 6: This bit is the opposite of the RI # input. This bit is equivalent to bit 2 of HCR in loopback
mode.
Bit 5: This bit is the opposite of the DSR# input. This bit is equivalent to bit 0 of HCR in loopback
mode.
Bit 4: This bit is the opposite of the CTS# input. This bit is equivalent to bit 1 of HCR in loopback
mode.
Bit 3: TDCD. This bit indicates that the DCD# pin has changed state after HSR was read by the CPU.
Bit 2: FERI. This bit indicates that the RI # pin has changed from low to high state after HSR was
read by the CPU.
Bit 1: TDSR. This bit indicates that the DSR# pin has changed state after HSR was read by the CPU.
Bit 0: TCTS. This bit indicates that the CTS# pin has changed state after HSR was read.
6.2.5 UART FIFO Control Register (UFR) (Write only)
This register is used to control the FIFO functions of the UART.
70 6 5 4 3 2 1
FIFO enable
Receiver FIFO reset
Transmitter FIFO reset
DMA mode select
Reserved
Reserved
RX interrupt active level (LSB)
RX interrupt active level (MSB)
Bit 6, 7: These two bits are used to set the active level for the receiver FIFO interrupt. For example, if
the interrupt active level is set as 4 bytes, once there are more than 4 data characters in the
receiver FIFO, the interrupt will be activated to notify the CPU to read the data from the FIFO.
TABLE 6-3 FIFO TRIGGER LEVEL
BIT 7 BIT 6 RX FIFO INTERRUPT ACTIVE LEVEL (BYTES)
0 0 01
0 1 04
1 0 08
1 1 14
Bit 4, 5: Reserved
Bit 3: When this bit is programmed to logic 1, the DMA mode will change from mode 0 to mode 1 if
UFR bit 0 = 1.
Publication Release Date: January, 2010
-50 - Revision 1.5
W83977EF-AW /W83977EG-AW
Bit 2: Setting this bit to a logical 1 resets the TX FIFO counter logic to initial state. This bit will clear to
a logical 0 by itself after being set to a logical 1.
Bit 1: Setting this bit to a logical 1 resets the RX FIFO counter logic to initial state. This bit will clear to
a logical 0 by itself after being set to a logical 1.
Bit 0: This bit enables the 16550 (FIFO) mode of the UART. This bit should be set to a logical 1 before
other bits of UFR are programmed.
6.2.6 Interrupt Status Register (ISR) (Read only)
This register reflects the UART interrupt status, which is encoded by different interrupt sources into 3
bits.
7 6 5 4 3 2 1
0
00
0 if interrupt pending
Interrupt Status bit 0
Interrupt Status bit 1
Interrupt Status bit 2
FIFOs enabled
FIFOs enabled
Bit 7, 6: These two bits are set to a logical 1 when UFR bit 0 = 1.
Bit 5, 4: These two bits are always logic 0.
Bit 3: In 16450 mode, this bit is 0. In 16550 mode, both bit 3 and 2 are set to a logical 1 when a time-
out interrupt is pending.
Bit 2, 1: These two bits identify the priority level of the pending interrupt, as shown in the table below.
Bit 0: This bit is a logical 1 if there is no interrupt pending. If one of the interrupt sources has occurred,
this bit will be set to a logical 0.
TABLE 6-4 INTERRUPT CONTROL FUNCTION
ISR INTERRUPT SET AND FUNCTION
Bit Bit Bit Bit Interrupt Interrupt Type Interrupt Source Clear Interrupt
3 2 1 0 priority
0 0 0 1 - - No Interrupt pending -
0 1 1 0 First UART Receive 1. OER = 1 2. PBER =1 Read USR
Status
3. NSER = 1 4. SBD = 1
0 1 0 0 Second RBR Data Ready 1. RBR data ready 1. Read RBR
2. FIFO interrupt active level 2. Read RBR until FIFO
reached data under active level
Publication Release Date: January, 2010
-51 - Revision 1.5
W83977EF-AW /W83977EG-AW
1 1 0 0 Second FIFO Data Timeout Data present in RX FIFO for 4 Read RBR
characters period of time since last
access of RX FIFO.
0 0 1 0 Third TBR Empty TBR empty 1. Write data into TBR
2. Read ISR (if priority is
third)
0 0 0 0 Fourth Handshake status 1. TCTS = 1 2. TDSR = 1 Read HSR
3. FERI = 1 4. TDCD = 1
** Bit 3 of ISR is enabled when bit 0 of UFR is logical 1.
6.2.7 Interrupt Control Register (ICR) (Read/Write)
This 8-bit register allows the five types of controller interrupts to activate the interrupt output signal
separately. The interrupt system can be totally disabled by resetting bits 0 through 3 of the Interrupt
Control Register (ICR). A selected interrupt can be enabled by setting the appropriate bits of this
register to a logical 1.
7 6 5 4 3 2 1 0
0 00 0
RBR data ready interrupt enable (ERDRI)
TBR empty interrupt enable (ETBREI)
UART receive status interrupt enable (EUSRI)
Handshake status interrupt enable (EHSRI)
Bit 7-4: These four bits are always logic 0.
Bit 3: EHSRI. Setting this bit to a logical 1 enables the handshake status register interrupt.
Bit 2: EUSRI. Setting this bit to a logical 1 enables the UART status register interrupt.
Bit 1: ETBREI. Setting this bit to a logical 1 enables the TBR empty interrupt.
Bit 0: ERDRI. Setting this bit to a logical 1 enables the RBR data ready interrupt.
6.2.8 Programmable Baud Generator (BLL/BHL) (Read/Write)
Two 8-bit registers, BLL and BHL, compose a programmable baud generator that uses 24 MHz to
16
generate a 1.8461 MHz frequency and divides it by a divisor from 1 to 2 -1. The output frequency of
the baud generator is the baud rate multiplied by 16, and this is the base frequency for the transmitter
and receiver. The table in the next page illustrates the use of the baud generator with a frequency of
1.8461 MHz. In high-speed UART mode (refer to CR0C bit7 and CR0C bit6), the programmable baud
generator directly uses 24 MHz and the same divisor as the normal speed divisor. In high-speed
mode, the data transmission rate can be as high as 1.5M bps.
6.2.9 User-defined Register (UDR) (Read/Write)
This is a temporary register that can be accessed and defined by the user.
Publication Release Date: January, 2010
-52 - Revision 1.5
W83977EF-AW /W83977EG-AW
TABLE 6-5 BAUD RATE TABLE
BAUD RATE FROM DIFFERENT PRE-DIVIDER
Pre-Div: 13 Pre-Div:1.625 Pre-Div: 1.0 Decimal divisor used Error Percentage between
to generate 16X desired and actual
1.8461M Hz 14.769M Hz 24M Hz
clock
50 400 650 2304 **
75 600 975 **
1536
110 880 1430 1047 0.18%
134.5 1076 1478.5 857 0.099%
150 1200 1950 768 **
300 2400 3900 384 **
600 4800 7800 192 **
1200 9600 15600 96 **
1800 14400 23400 **
64
2000 16000 26000 58 0.53%
2400 19200 31200 **
48
3600 28800 46800 32 **
4800 38400 62400 **
24
7200 57600 93600 16 **
9600 76800 124800 **
12
19200 153600 249600 6 **
38400 307200 499200 3 **
57600 460800 748800 2 **
115200 921600 1497600 1 **
** The percentage error for all baud rates, except where indicated otherwise, is 0.16%.
Note. Pre-Divisor is determined by CRF0 of UART A and B.
Publication Release Date: January, 2010
-53 - Revision 1.5
W83977EF-AW /W83977EG-AW
7. PARALLEL PORT
7.1 Printer Interface Logic
The parallel port of W83977EF-AW/EG makes possible the attachment of various devices that accept
eight bits of parallel data at standard TTL level. W83977EF-AW/EG supports an IBM XT/AT
compatible parallel port (SPP), bi-directional parallel port (BPP), Enhanced Parallel Port (EPP),
Extended Capabilities Parallel Port (ECP), Extension FDD mode (EXTFDD), Extension 2FDD mode
(EXT2FDD) on the parallel port. Refer to the configuration registers for more information on disabling,
power-down, and on selecting the mode of operation.
Table 7-1 shows the pin definitions for different modes of the parallel port.
TABLE 7-1-1 PARALLEL PORT CONNECTOR AND PIN DEFINITIONS
PIN NUMBER
HOST PIN
OF W83977EF- SPP EPP ECP
CONNECTOR ATTRIBUTE
AW
2
1 36 O nSTB nWrite nSTB, HostClk
2-9 31-26, 24-23 I/O PD<0:7> PD<0:7> PD<0:7>
2
10 22 I nACK Intr nACK, PeriphClk
2
11 21 I BUSY nWait BUSY, PeriphAck
2
12 19 I PE PE PEerror, nAckReverse
2
13 18 I SLCT Select SLCT, Xflag
2
14 35 O nAFD nDStrb nAFD, HostAck
1 2
15 34 I nERR nError nFault , nPeriphRequest
1 2
16 33 O nINIT nInit nINIT , nReverseRqst
1 2
17 32 O nSLIN nAStrb nSLIN , ECPMode
Notes:
n
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the W83977EG-AW have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
Winbond W29C011A-15 Memory Module - 1-megabit, 5-volt only CMOS flash memory with a standard 5V powe...
Manufacturers







What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods