Elite.Parts Manufacturers W WINBOND W83697HG
About product Features Datasheet FAQ

WINBOND W83697HG

Image of WINBOND W83697HG

Description

WINBOND-W83697HG

Part Number

W83697HG

Price

Request Quote

Manufacturer

WINBOND

Lead Time

Request Quote

Category

PRODUCTS - W

Features

Datasheet

pdf file

W83697HG-Winbond-datasheet1-1751999065.pdf

704 KiB

Extracted Text

W83697HF/HG Data Sheet WINBOND LPC I/O WINBOND LPC I/O W83697HF W83697HG Date: May 30, 2005 Revision: A1 Publication Release Date: May 30, 2005 - i - Revision A1 W83697HF/ HG Table of Content- 1. GENERAL DESCRIPTION ......................................................................................................... 1 2. FEATURES ................................................................................................................................. 2 3. BLOCK DIAGRAM FOR W83697HF .......................................................................................... 5 4. PIN CONFIGURATION FOR W83697HF................................................................................... 6 5. PIN DESCRIPTION.................................................................................................................... 7 5.1 LPC Interface.................................................................................................................. 8 5.2 FDC Interface ................................................................................................................. 9 5.3 Multi-Mode Parallel Port ............................................................................................... 10 5.4 Serial Port Interface ...................................................................................................... 15 5.5 Infrared Port.................................................................................................................. 16 5.6 Flash ROM Interface..................................................................................................... 16 5.7 Hardware Monitor Interface .......................................................................................... 17 5.8 Game Port & MIDI Port................................................................................................. 18 5.9 POWER PINS............................................................................................................... 19 6. HARDWARE MONITOR ........................................................................................................... 20 6.1 General Description...................................................................................................... 20 6.2 Access Interface ........................................................................................................... 20 6.2.1 LPC interface..................................................................................................................20 6.3 Analog Inputs................................................................................................................ 22 6.3.1 Monitor over 4.096V voltage:..........................................................................................23 6.3.2 Monitor negative voltage:................................................................................................23 6.3.3 Temperature Measurement Machine..............................................................................24 6.4 FAN Speed Count and FAN Speed Control ................................................................. 25 6.4.1 Fan speed count.............................................................................................................25 6.4.2 Fan speed control...........................................................................................................27 6.5 SMI# interrupt mode ..................................................................................................... 28 6.5.1 Voltage SMI# mode : ......................................................................................................28 6.5.2 Fan SMI# mode :............................................................................................................28 6.5.3 The W83697HF temperature sensor 1 SMI# interrupt has two modes:..........................29 6.5.4 The W83697HF temperature sensor 2 SMI# interrupt has two modes and it is programmed at CR[4Ch] bit 6. ...................................................................................................30 6.6 OVT# interrupt mode .................................................................................................... 31 6.6.1 The W83697HF temperature sensor 2 Over-Temperature (OVT#) has the following modes 31 6.7 REGISTERS AND RAM ............................................................................................... 32 7. CONFIGURATION REGISTER ................................................................................................ 62 - ii - W83697HF/ HG 7.1 Plug and Play Configuration ......................................................................................... 62 7.2 Compatible PnP............................................................................................................ 62 7.2.1 Extended Function Registers..........................................................................................62 7.2.2 Extended Functions Enable Registers (EFERs) .............................................................63 7.2.3 Extended Function Index Registers (EFIRs), Extended Function Data Registers(EFDRs) 63 7.3 Configuration Sequence ............................................................................................... 63 7.3.1 Enter the extended function mode..................................................................................63 7.3.2 Configurate the configuration registers...........................................................................63 7.3.3 Exit the extended function mode ....................................................................................63 7.3.4 Software programming example.....................................................................................64 7.4 Chip (Global) Control Register ..................................................................................... 65 7.5 Logical Device 0 (FDC)................................................................................................. 70 7.6 Logical Device 1 (Parallel Port) .................................................................................... 73 7.7 Logical Device 2 (UART A)........................................................................................... 74 7.8 Logical Device 3 (UART B)........................................................................................... 75 7.9 Logical Device 6 (CIR).................................................................................................. 76 7.10 Logical Device 7 (Game Port GPIO Port 1).................................................................. 77 7.11 Logical Device 8 (MIDI Port and GPIO Port 5)............................................................. 78 7.12 Logical Device 9 (GPIO Port 2 ~ GPIO Port 4 ) ........................................................... 80 7.13 Logical Device A (ACPI) ............................................................................................... 82 7.14 Logical Device B (Hardware Monitor)........................................................................... 87 8. SPECIFICATIONS .................................................................................................................... 88 8.1 Absolute Maximum Ratings.......................................................................................... 88 8.2 DC CHARACTERISTICS.............................................................................................. 88 9. APPLICATION CIRCUITS ........................................................................................................ 96 9.1 Parallel Port Extension FDD......................................................................................... 96 9.2 Parallel Port Extension 2FDD....................................................................................... 97 9.3 Four FDD Mode ............................................................................................................ 97 10. ORDERING INSTRUNCTION .................................................................................................. 98 11. HOW TO READ THE TOP MARKING...................................................................................... 98 12. PACKAGE DIMENSIONS......................................................................................................... 99 13. APPENDIX A : DEMO CIRCUIT ............................................................................................. 100 14. REVISION HISTORY.............................................................................................................. 105 Publication Release Date: May 30, 2005 - iii - Revision A1 W83697HF/ HG 1. GENERAL DESCRIPTION The W83697HF is evolving product from Winbond's most popular I/O family. They feature a whole new interface, namely LPC (Low Pin Count) interface, which will be supported in the new generation chip-set. This interface as its name suggests is to provide an economical implementation of I/O's interface with lower pin count and still maintains equivalent performance as its ISA interface counterpart. Approximately 40 pin counts are saved in LPC I/O comparing to ISA implementation. With this additional freedom, we can implement more devices on a single chip as demonstrated in W83697HF's integration of Game Port and MIDI Port. It is fully transparent in terms of software which means no BIOS or device driver update is needed except chip-specific configuration. The disk drive adapter functions of W83697HF include a floppy disk drive controller compatible with the industry standard 82077/ 765, data separator, write pre-compensation circuit, decode logic, data rate selection, clock generator, drive interface control logic, and interrupt and DMA logic. The wide range of functions integrated onto the W83697HF greatly reduces the number of components required for interfacing with floppy disk drives. The W83697HF supports four 360K, 720K, 1.2M, 1.44M, or 2.88M disk drives and data transfer rates of 250 Kb/s, 300 Kb/s, 500 Kb/s,1 Mb/s, and 2 Mb/s. The W83697HF provides two high-speed serial communication ports (UARTs), one of which supports serial Infrared communication. Each UART includes a 16-byte send/receive FIFO, a programmable baud rate generator, complete modem control capability, and a processor interrupt system. Both UARTs provide legacy speed with baud rate up to 115.2k bps and also advanced speed with baud rates of 230k, 460k, or 921k bps which support higher speed modems. In addition, the W83697HF provides IR functions: IrDA 1.0 (SIR for 1.152K bps) and TV remote IR (Consumer IR, supporting NEC, RC-5, extended RC-5, and RECS-80 protocols). The W83697HF supports one PC-compatible printer port (SPP), Bi-directional Printer port (BPP) and also Enhanced Parallel Port (EPP) and Extended Capabilities Port (ECP). Through the printer port interface pins, also available are: Extension FDD Mode and Extension 2FDD Mode allowing one or two external floppy disk drives to be connected. The configuration registers support mode selection, function enable/disable, and power down function selection. Furthermore, the configurable PnP features are compatible with the plug-and-play feature demand of Windows TM 95/98 , which makes system resource allocation more efficient than ever. The W83697HF provides a set of flexible I/O control functions to the system designer through a set of General Purpose I/O ports. These GPIO ports may serve as simple I/O or may be individually configured to provide a predefined alternate function. General Purpose Port 1 is designed to be functional even in power down mode (VCC is off).  The W83697HF is made to fully comply with Microsoft PC98 and PC99 Hardware Design Guide, and meet the requirements of ACPI. The W83697HF contains a game port and a MIDI port. The game port is designed to support 2 joysticks and can be applied to all standard PC game control devices, They are very important for a entertainment or consumer computer. The W83697HF provides Flash ROM interface. That can support up to 4M legacy flash ROM. The W83697HF support hardware status monitoring for personal computers. It can be used to monitor several critical hardware parameters of the system, including power supply voltages, fan speeds, and temperatures, which are very important for a high-end computer system to work stably and properly. Moreover, W83697HF support TM TM the Smart Fan control system, including the thermal Cruise ” and speed Cruise ” functions. Smart Fan can make system more stable and user friendly. Publication Release Date: May 30, 2005 - 1 - Revision A1 W83697HF/ HG 2. FEATURES General • Meet LPC Spec. 1.01 • Support LDRQ#(LPC DMA), SERIRQ (serial IRQ) • Include all the features of Winbond I/O W83877TF • Integrate Hardware Monitor functions • Compliant with Microsoft PC98/PC99 Hardware Design Guide • Support DPM (Device Power Management), ACPI • Programmable configuration settings • Single 24 or 48 MHz clock input FDC • Compatible with IBM PC AT disk drive systems • Variable write pre-compensation with track selectable capability • Support vertical recording format • DMA enable logic • 16-byte data FIFOs • Support floppy disk drives and tape drives • Detects all overrun and under run conditions • Built-in address mark detection circuit to simplify the read electronics • FDD anti-virus functions with software write protect and FDD write enable signal (write data signal was forced to be inactive) • Support up to four 3.5-inch or 5.25-inch floppy disk drives • Completely compatible with industry standard 82077 • 360K/720K/1.2M/1.44M/2.88M format; 250K, 300K, 500K, 1M, 2M bps data transfer rate • Support 3-mode FDD, and its Win95/98 driver UART • Two high-speed 16550 compatible UARTs with 16-byte send/receive FIFOs • MIDI compatible • Fully programmable serial-interface characteristics: --- 5, 6, 7 or 8-bit characters --- Even, odd or no parity bit generation/detection --- 1, 1.5 or 2 stop bits generation • Internal diagnostic capabilities: • --- Loop-back controls for communications link fault isolation --- Break, parity, overrun, framing error simulation 16 • Programmable baud generator allows division of 1.8461 MHz and 24 MHz by 1 to (2 -1) • Maximum baud rate up to 921k bps for 14.769 MHz and 1.5M bps for 24 MHz - 2 - W83697HF/ HG • Infrared • Support IrDA version 1.0 SIR protocol with maximum baud rate up to 115.2K bps • Support SHARP ASK-IR protocol with maximum baud rate up to 57,600 bps • Support Consumer IR with Wake-Up function. • Parallel Port • Compatible with IBM parallel port • Support PS/2 compatible bi-directional parallel port • Support Enhanced Parallel Port (EPP) − Compatible with IEEE 1284 specification • Support Extended Capabilities Port (ECP) − Compatible with IEEE 1284 specification • Extension FDD mode supports disk drive B; and Extension 2FDD mode supports disk drives A and B through parallel port • Enhanced printer port back-drive current protection • Game Port • Support two separate Joysticks • Support every Joystick two axes (X,Y) and two buttons (S1,S2) controllers • MIDI Port • The baud rate is 31.25 K baud rate • 16-byte input FIFO • 16-byte output FIFO • Flash ROM Interface • Support up to 4M flash ROM • General Purpose I/O Ports • 48 programmable general purpose I/O ports • General purpose I/O ports can serve as simple I/O ports, watch dog timer output, power LED output, infrared I/O pins, suspend LED output, Beep output • Functional in power down mode Publication Release Date: May 30, 2005 - 3 - Revision A1 W83697HF/ HG Hardware Monitor Functions TM TM • Smart fan control system, support thermal Cruise ” and speed Cruise ” TM • 2 thermal inputs from optionally remote thermistors or 2N3904 transistors or Pentium II/III thermal diode output • 6 positive voltage inputs (typical for +12V, -12V, +5V, -5V, +3.3V, Vcore) • 2 intrinsic voltage monitoring (typical for Vbat, +5VSB) • 2 fan speed monitoring inputs • 2 fan speed control • Build in Case open detection circuit • WATCHDOG comparison of all monitored values • Programmable hysteresis and setting points for all monitored items • Over temperature indicate output • Automatic Power On voltage detection Beep • Issue SMI#, IRQ, OVT# to activate system protection TM • Winbond Hardware Doctor Support TM TM • Intel LDCM / Acer ADM compatible Package • 128-pin PQFP - 4 - W83697HF/ HG 3. BLOCK DIAGRAM FOR W83697HF LRESET#, LCLK, LFRAME#, LAD[3:0], LDRQ#, SERIRQ LPC Interface Joystick interface Floppy drive Game FDC signals interface signals Port MSI Serial port A, B MIDI URA, B interface signals MSO IRRX General-purpose GPIO IR I/O pins IRTX Hardware monitor HM CIR CIRRX# channel and Vref Flash ROM Printer port Flash PRT interface signals interface signals ROM ACPI Publication Release Date: May 30, 2005 - 5 - Revision A1 W83697HF/ HG 4. PIN CONFIGURATION FOR W83697HF VT VT VT VTI I I IN N N N2 2 2 2 103 103 103 103 103 64 64 64 64 64 IR IR IR IRR R R RX X X X 63 63 63 63 63 RIB RIB RIB RIB# # # # VT VT VT VTI I I IN N N N1 1 1 1 104 104 104 104 104 AV AV AV AVC C C CC C C C 62 62 62 62 62 DCDB DCDB DCDB DCDB# # # # 105 105 105 105 105 VR VR VR VRE E E EF F F F 61 61 61 61 61 SOU SOU SOU SOUT T T TB/ B/ B/ B/PEN PEN PEN PEN4 4 4 48 8 8 8 106 106 106 106 106 60 60 60 60 60 GN GN GN GND D D D VC VC VC VCOR OR OR ORE E E E 107 107 107 107 107 +3 +3 +3 +3. . . .3 3 3 3V V V VI I I IN N N N 108 108 108 108 108 59 59 59 59 59 SI SI SI SIN N N NB B B B +1 +1 +1 +12 2 2 2V V V VI I I IN N N N 58 58 58 58 58 DT DT DT DTRB RB RB RB# # # # 109 109 109 109 109 -1 -1 -1 -12V 2V 2V 2VIIIIN N N N 57 57 57 57 57 RT RT RT RTS S S SB B B B# # # # 110 110 110 110 110 -5 -5 -5 -5VI VI VI VIN N N N 111 111 111 111 111 56 56 56 56 56 DS DS DS DSRB RB RB RB# # # # AG AG AG AGN N N ND D D D 55 55 55 55 55 CT CT CT CTS S S SB B B B# # # # 112 112 112 112 112 FA FA FA FAN N N NIIIIO O O O2 2 2 2 RIA RIA RIA RIA# # # # 113 113 113 113 113 54 54 54 54 54 FA FA FA FAN N N NIIIIO O O O1 1 1 1 53 53 53 53 53 DCDA DCDA DCDA DCDA# # # # 114 114 114 114 114 FA FA FA FAN N N NP P P PW W W WM M M M2 2 2 2 115 115 115 115 115 52 52 52 52 52 SOU SOU SOU SOUT T T TA/ A/ A/ A/PEN PEN PEN PENR R R RO O O OM M M M# # # # FA FA FA FAN N N NP P P PW W W WM M M M1 1 1 1 116 116 116 116 116 W W W W83697H 83697H 83697H 83697HF F F F 51 51 51 51 51 SI SI SI SIN N N NA A A A OVT OVT OVT OVT# # # #/ / / /S S S SM M M MI I I I# # # # 50 50 50 50 50 D D D DT T T TR R R RA A A A#/ #/ #/ #/PN PN PN PNP P P PC C C CSV# SV# SV# SV# 117 117 117 117 117 BEE BEE BEE BEEP P P P 118 118 118 118 118 49 49 49 49 49 RT RT RT RTS S S SA A A A# # # #////HE HE HE HEF F F FR R R RA A A AS S S S M MS SI I/ /GP5 GP51 1/ /W WD DT TO# O# 48 48 48 48 48 DS DS DS DSRA RA RA RA# # # # 119 119 119 119 119 M M M MS S S SO/ O/ O/ O/GP GP GP GP5 5 5 50 0 0 0/ / / /P P P PLE LE LE LED D D D 47 47 47 47 47 CT CT CT CTS S S SA A A A# # # # 120 120 120 120 120 46 46 46 46 46 ST ST ST STB B B B# # # # GPAS GPAS GPAS GPAS2/ 2/ 2/ 2/GP1 GP1 GP1 GP17 7 7 7 121 121 121 121 121 GPBS GPBS GPBS GPBS2/ 2/ 2/ 2/GP1 GP1 GP1 GP16 6 6 6 45 45 45 45 45 VC VC VC VCC C C C 122 122 122 122 122 GPA GPA GPA GPAY Y Y Y/ / / /G G G GP15 P15 P15 P15 123 123 123 123 123 44 44 44 44 44 AF AF AF AFD D D D# # # # 43 43 43 43 43 IN IN IN INIT IT IT IT# # # # GPB GPB GPB GPBY Y Y Y/ / / /G G G GP14 P14 P14 P14 124 124 124 124 124 GPB GPB GPB GPBX X X X/ / / /G G G GP1 P1 P1 P13 3 3 3 42 42 42 42 42 PD PD PD PD0 0 0 0 125 125 125 125 125 GPA GPA GPA GPAX X X X/ / / /G G G GP1 P1 P1 P12 2 2 2 41 41 41 41 41 PD PD PD PD1 1 1 1 126 126 126 126 126 40 40 40 40 40 PD PD PD PD2 2 2 2 GPBS GPBS GPBS GPBS1/ 1/ 1/ 1/GP1 GP1 GP1 GP11 1 1 1 127 127 127 127 127 GPAS GPAS GPAS GPAS1/ 1/ 1/ 1/GP1 GP1 GP1 GP10 0 0 0 128 128 128 128 128 39 39 39 39 39 PD PD PD PD3 3 3 3 - 6 - D D D DRV RV RV RVDE DE DE DEN0 N0 N0 N0 102 102 102 102 102 VBAT VBAT VBAT VBAT 1 1 1 1 101 101 101 101 101 INDE INDE INDE INDEX X X X# # # # C C C CASEOP ASEOP ASEOP ASEOPE E E EN N N N# # # # 2 2 2 2 100 100 100 100 100 MO MO MO MOA A A A# # # # CI CI CI CIRRX RRX RRX RRX 3 3 3 3 99 99 99 99 99 D D D DSB# SB# SB# SB# VSB VSB VSB VSB 4 4 4 4 98 98 98 98 98 VC VC VC VCC C C C PM PM PM PME# E# E# E# 5 5 5 5 D D D DSA# SA# SA# SA# 97 97 97 97 97 ME ME ME MEMW MW MW MW# # # #/ / / /G G G GP P P P5 5 5 52 2 2 2 6 6 6 6 96 96 96 96 96 MO MO MO MOB B B B# # # # ME ME ME MEMR MR MR MR# # # #G G G GP P P P5 5 5 53 3 3 3 7 7 7 7 DIR# DIR# DIR# DIR# 95 95 95 95 95 R R R RO O O OM M M MC C C CS#/ S#/ S#/ S#/G G G GP5 P5 P5 P54 4 4 4 8 8 8 8 94 94 94 94 94 ST ST ST STEP# EP# EP# EP# X X X XD D D DO/ O/ O/ O/GP2 GP2 GP2 GP20 0 0 0 9 9 9 9 93 93 93 93 93 WD# WD# WD# WD# XD XD XD XD1 1 1 1/ / / /G G G GP P P P2 2 2 21 1 1 1 10 10 10 10 WE WE WE WE# # # # 92 92 92 92 92 XD XD XD XD2 2 2 2/ / / /G G G GP P P P2 2 2 22 2 2 2 11 11 11 11 91 91 91 91 91 T T T TR R R RAK0# AK0# AK0# AK0# XD XD XD XD3 3 3 3/ / / /G G G GP P P P2 2 2 23 3 3 3 12 12 12 12 WP WP WP WP# # # # 90 90 90 90 90 GN GN GN GND D D D 13 13 13 13 RDA RDA RDA RDAT T T TA A A A# # # # 89 89 89 89 89 XD XD XD XD4 4 4 4/ / / /G G G GP P P P2 2 2 24 4 4 4 14 14 14 14 88 88 88 88 88 H H H HEAD EAD EAD EAD# # # # XD XD XD XD5 5 5 5/ / / /G G G GP P P P2 2 2 25 5 5 5 15 15 15 15 87 87 87 87 87 D D D DS S S SK K K KCHG CHG CHG CHG# # # # XD XD XD XD6 6 6 6/ / / /G G G GP P P P2 2 2 26 6 6 6 16 16 16 16 CL CL CL CLK K K KIIIIN N N N 86 86 86 86 86 XD XD XD XD7 7 7 7/ / / /G G G GP P P P2 2 2 27 7 7 7 17 17 17 17 GN GN GN GND D D D 85 85 85 85 85 XA XA XA XA0 0 0 0/ / / /G G G G P P P P3 3 3 30 0 0 0 18 18 18 18 84 84 84 84 84 PC PC PC PCI I I IC C C CLK LK LK LK XA XA XA XA1 1 1 1/ / / /G G G G P P P P3 3 3 31 1 1 1 19 19 19 19 L L L LDRQ DRQ DRQ DRQ# # # # 83 83 83 83 83 XA XA XA XA2 2 2 2/ / / /G G G G P P P P3 3 3 32 2 2 2 20 20 20 20 S S S SE E E ERI RI RI RIRQ RQ RQ RQ 82 82 82 82 82 XA XA XA XA3 3 3 3/ / / /G G G G P P P P3 3 3 33 3 3 3 21 21 21 21 81 81 81 81 81 V V V VCC3 CC3 CC3 CC3 XA XA XA XA4 4 4 4/ / / /G G G G P P P P3 3 3 34 4 4 4 22 22 22 22 LA LA LA LAD D D D3 3 3 3 80 80 80 80 80 XA XA XA XA5 5 5 5/ / / /G G G G P P P P3 3 3 35 5 5 5 23 23 23 23 79 79 79 79 79 LAD LAD LAD LAD2 2 2 2 XA XA XA XA6 6 6 6/ / / /G G G G P P P P3 3 3 36 6 6 6 24 24 24 24 LAD LAD LAD LAD1 1 1 1 78 78 78 78 78 XA XA XA XA7 7 7 7/ / / /G G G G P P P P3 3 3 37 7 7 7 25 25 25 25 LA LA LA LAD D D D0 0 0 0 77 77 77 77 77 XA XA XA XA8 8 8 8/ / / /G G G G P P P P4 4 4 40 0 0 0 26 26 26 26 76 76 76 76 76 L L L LF F F FR R R RAM AM AM AME# E# E# E# XA XA XA XA9 9 9 9/ / / /G G G G P P P P4 4 4 41 1 1 1 27 27 27 27 LR LR LR LRE E E ESET SET SET SET# # # # 75 75 75 75 75 VC VC VC VCC C C C 28 28 28 28 SLC SLC SLC SLCT T T T 74 74 74 74 74 XA XA XA XA1 1 1 1 0 0 0 0/ / / /G G G GP P P P4 4 4 42 2 2 2 29 29 29 29 PE PE PE PE 73 73 73 73 73 XA XA XA XA1 1 1 1 1 1 1 1/ / / /G G G GP P P P4 4 4 43 3 3 3 30 30 30 30 72 72 72 72 72 BU BU BU BUSY SY SY SY XA XA XA XA1 1 1 1 2 2 2 2/ / / /G G G GP P P P4 4 4 44 4 4 4 31 31 31 31 AC AC AC ACK# K# K# K# 71 71 71 71 71 XA XA XA XA1 1 1 1 3 3 3 3/ / / /G G G GP P P P4 4 4 45 5 5 5 32 32 32 32 E E E ERR# RR# RR# RR# 70 70 70 70 70 XA XA XA XA1 1 1 1 4 4 4 4/ / / /G G G GP P P P4 4 4 46 6 6 6 33 33 33 33 69 69 69 69 69 SLI SLI SLI SLIN N N N# # # # XA XA XA XA1 1 1 1 5 5 5 5/ / / /G G G GP P P P4 4 4 47 7 7 7 34 34 34 34 PD PD PD PD7 7 7 7 68 68 68 68 68 XA XA XA XA1 1 1 1 6 6 6 6/ / / /G G G GP P P P5 5 5 55 5 5 5 35 35 35 35 67 67 67 67 67 PD PD PD PD6 6 6 6 XA XA XA XA1 1 1 1 7 7 7 7/ / / /G G G GP P P P5 5 5 56 6 6 6 36 36 36 36 PD PD PD PD5 5 5 5 66 66 66 66 66 XA XA XA XA1 1 1 1 8 8 8 8/ / / /G G G GP P P P5 5 5 57 7 7 7 37 37 37 37 PD PD PD PD4 4 4 4 65 65 65 65 65 IR IR IR IRT T T TX X X X 38 38 38 38 W83697HF/ HG 5. PIN DESCRIPTION Note: Please refer to Section 10.2 DC CHARACTERISTICS for details PIN DESCRIPTION I/O TTL level bi-directional pin with 8mA source-sink capability 8t I/O TTL level bi-directional pin with 12mA source-sink capability 12t I/O TTL level bi-directional pin with 24 mA source-sink capability 24t I/O 3.3V TTL level bi-directional pin with 12mA source-sink capability 12tp3 I/O TTL level Schmitt-trigger bi-directional pin with 12mA source-sink capability 12ts I/O TTL level Schmitt-trigger bi-directional pin with 24mA source-sink capability 24ts I/O 3.3V TTL level Schmitt-trigger bi-directional pin with 24mA source-sink capability 24tsp3 I/OD TTL level bi-directional pin and open-drain output with 12mA sink capability 12t I/OD TTL level bi-directional pin and open-drain output with 24mA sink capability 24t I/OD CMOS level bi-directional pin and open-drain output with 24mA sink capability 24c I/OD Bi-directional pin with analog input and open-drain output with 24mA sink capability 24a I/OD TTL level Schmitt-trigger bi-directional pin and open-drain output with 12mA sink capability 12ts I/OD TTL level Schmitt-trigger bi-directional pin and open-drain output with 24mA sink capability 24ts I/OD CMOS level Schmitt-trigger bi-directional pin and open-drain output with 12mA sink capability 12cs I/OD CMOS level Schmitt-trigger bi-directional pin and open-drain output with 16mA sink capability 16cs I/OD CMOS level Schmitt-trigger bi-directional pin and open-drain output with 24mA sink capability 24cs CMOS level Schmitt-trigger bi-directional pin with internal pull down resistor and open-drain output I/OD 12csd with 12mA sink capability CMOS level Schmitt-trigger bi-directional pin with internal pull up resistor and open-drain output with I/OD 12csu 12mA sink capability O Output pin with 4 mA source-sink capability 4 O Output pin with 8 mA source-sink capability 8 O Output pin with 12 mA source-sink capability 12 O Output pin with 16 mA source-sink capability 16 O Output pin with 24 mA source-sink capability 24 O 3.3V output pin with 12 mA source-sink capability 12p3 O 3.3V output pin with 24 mA source-sink capability 24p3 OD Open-drain output pin with 8 mA sink capability 8 OD Open-drain output pin with 12 mA sink capability 12 OD Open-drain output pin with 24 mA sink capability 24 OD 3.3V open-drain output pin with 12 mA sink capability 12p3 IN TTL level input pin t IN tp3 3.3V TTL level input pin Publication Release Date: May 30, 2005 - 7 - Revision A1 W83697HF/ HG PIN DESCRIPTION, Continued. PIN DESCRIPTION IN TTL level input pin with internal pull down resistor td IN TTL level input pin with internal pull up resistor tu IN TTL level Schmitt-trigger input pin ts IN 3.3V TTL level Schmitt-trigger input pin tsp3 IN c CMOS level input pin IN cu CMOS level input pin with internal pull up resistor IN CMOS level input pin with internal pull down resistor cd IN CMOS level Schmitt-trigger input pin cs IN CMOS level Schmitt-trigger input pin with internal pull up resistor csu 5.1 LPC Interface SYMBOL PIN I/O FUNCTION System clock input. According to the input frequency 24MHz or IN CLKIN 17 tp3 48MHz, it is selectable through register. Default is 24MHz input. PME# 98 OD Generated PME event. 12p3 IN PCICLK 19 PCI clock 33 MHz input. tsp3 O LDRQ# 20 Encoded DMA Request signal. 12p3 SERIRQ 21 I/O12tp3 Serial IRQ input/Output. These signal lines communicate address, control, and data I/O LAD[3:0] 23-26 12tp3 information over the LPC bus between a host and a peripheral. LFRAME# 27 IN Indicates start of a new cycle or termination of a broken cycle. tsp3 IN LRESET# 28 Reset signal. It can connect to PCIRST# signal on the host. tsp3 - 8 - W83697HF/ HG 5.2 FDC Interface SYMBOL PIN I/O FUNCTION OD DRVDEN0 1 Drive Density Select bit 0. 24 This Schmitt-triggered input from the disk drive is active low when the head is positioned over the beginning of a track marked IN INDEX# 2 by an index hole. This input pin is pulled up internally by a 1 KΩ csu resistor. The resistor can be disabled by bit 7 of L0-CRF0 (FIPURDWN). Motor A On. When set to 0, this pin enables disk drive 0. This is OD MOA# 3 24 an open drain output. Drive Select B. When set to 0, this pin enables disk drive B. OD DSB# 4 24 This is an open drain output. Drive Select A. When set to 0, this pin enables disk drive A. OD DSA# 6 24 This is an open drain output. Motor B On. When set to 0, this pin enables disk drive 1. This is OD MOB# 7 24 an open drain output. Direction of the head step motor. An open drain output. OD DIR# 8 Logic 1 = outward motion 24 Logic 0 = inward motion Step output pulses. This active low open drain output produces OD STEP# 9 24 a pulse to move the head to another track. Write data. This logic low open drain writes pre-compensation OD WD# 10 24 serial data to the selected FDD. An open drain output. WE# 11 OD Write enable. An open drain output. 24 Track 0. This Schmitt-triggered input from the disk drive is active low when the head is positioned over the outermost track. This IN TRAK0# 12 csu input pin is pulled up internally by a 1 KΩ resistor. The resistor can be disabled by bit 7 of L0-CRF0 (FIPURDWN). Write protected. This active low Schmitt input from the disk drive indicates that the diskette is write-protected. This input pin is IN WP# 13 csu pulled up internally by a 1 KΩ resistor. The resistor can be disabled by bit 7 of L0-CRF0 (FIPURDWN). The read data input signal from the FDD. This input pin is pulled IN RDATA# 14 up internally by a 1 KΩ resistor. The resistor can be disabled by csu bit 7 of L0-CRF0 (FIPURDWN). HEAD# 15 OD Head select. This open drain output determines which disk drive 24 head is active. Logic 1 = side 0 Logic 0 = side 1 DSKCHG# 16 IN Diskette change. This signal is active low at power on and csu whenever the diskette is removed. This input pin is pulled up internally by a 1 KΩ resistor. The resistor can be disabled by bit 7 of L0-CRF0 (FIPURDWN). Publication Release Date: May 30, 2005 - 9 - Revision A1 W83697HF/ HG 5.3 Multi-Mode Parallel Port The following pins have alternate functions, which are controlled by CR28 and L3-CRF0. SYMBOL PIN I/O FUNCTION PRINTER MODE: An active high input on this pin indicates that the printer is IN ts SLCT 29 selected. This pin is pulled high internally. Refer to the description of the parallel port for definition of this pin in ECP and EPP mode. OD EXTENSION FDD MODE: WE2# 12 WE2# This pin is for Extension FDD B; its function is the same as the pin of FDC. WE# EXTENSION 2FDD MODE: WE2# This pin is for Extension FDD A and B; its function is the same as the pin of FDC. WE# PRINTER MODE: An active high input on this pin indicates that the printer has PE IN ts 30 detected the end of the paper. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. OD EXTENSION FDD MODE: WD2# 12 WD2# This pin is for Extension FDD B; its function is the same as the pin of FDC. WD# EXTENSION 2FDD MODE: WD2# This pin is for Extension FDD A and B; its function is the same as the pin of FDC. WD# - 10 - W83697HF/ HG 5.3 Multi-Mode Parallel Port, continued SYMBOL PIN I/O FUNCTION PRINTER MODE: IN t An active high input indicates that the printer is not ready to BUSY 31 receive data. This pin is pulled high internally. Refer to the description of the parallel port for definition of this pin in ECP and EPP mode. OD EXTENSION FDD MODE: MOB2# 12 MOB2# This pin is for Extension FDD B; its function is the same as the MOB# pin of FDC. EXTENSION 2FDD MODE: MOB2# This pin is for Extension FDD A and B; its function is the same as the MOB# pin of FDC. PRINTER MODE: ACK# IN ts An active low input on this pin indicates that the printer has received data and is ready to accept more data. This pin is ACK# pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. EXTENSION FDD MODE: DSB2# 32 OD 12 This pin is for the Extension FDD B; its functions is the same as the DSB# pin of FDC. DSB2# EXTENSION 2FDD MODE: DSB2# This pin is for Extension FDD A and B; its function is the same as the DSB# pin of FDC. PRINTER MODE: ERR# ERR# IN ts An active low input on this pin indicates that the printer has encountered an error condition. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. 33 EXTENSION FDD MODE: HEAD2# OD 12 This pin is for Extension FDD B; its function is the same as the HEAD2# HEAD#pin of FDC. EXTENSION 2FDD MODE: HEAD2# This pin is for Extension FDD A and B; its function is the same as the HEAD# pin of FDC. Publication Release Date: May 30, 2005 - 11 - Revision A1 W83697HF/ HG 5.3 Multi-Mode Parallel Port, continued SYMBOL PIN I/O FUNCTION SLIN# 34 OD PRINTER MODE: SLIN# 12 Output line for detection of printer selection. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. EXTENSION FDD MODE: STEP2# OD 12 STEP2# This pin is for Extension FDD B; its function is the same as the STEP# pin of FDC. EXTENSION 2FDD MODE: STEP2# This pin is for Extension FDD A and B; its function is the same as the STEP# pin of FDC. INIT# 43 OD PRINTER MODE: INIT# 12 Output line for the printer initialization. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. EXTENSION FDD MODE: DIR2# OD 12 DIR2# This pin is for Extension FDD B; its function is the same as the DIR# pin of FDC. EXTENSION 2FDD MODE: DIR2# This pin is for Extension FDD A and B; its function is the same as the DIR# pin of FDC. AFD# 44 OD PRINTER MODE: AFD# 12 An active low output from this pin causes the printer to auto feed a line after a line is printed. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. OD EXTENSION FDD MODE: DRVDEN0 12 DRVDEN0 This pin is for Extension FDD B; its function is the same as the DRVDEN0 pin of FDC. EXTENSION 2FDD MODE: DRVDEN0 This pin is for Extension FDD A and B; its function is the same as the DRVDEN0 pin of FDC. - 12 - W83697HF/ HG 5.3 Multi-Mode Parallel Port, continued SYMBOL PIN I/O FUNCTION STB# 46 OD PRINTER MODE: STB# 12 An active low output is used to latch the parallel data into the printer. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. - EXTENSION FDD MODE: This pin is a tri-state output. - EXTENSION 2FDD MODE: This pin is a tri-state output. PD0 42 I/O PRINTER MODE: PD0 12ts Parallel port data bus bit 0. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. INDEX2# IN EXTENSION FDD MODE: INDEX2# ts This pin is for Extension FDD B; its function is the same as the INDEX# pin of FDC. It is pulled high internally. EXTENSION 2FDD MODE: INDEX2# This pin is for Extension FDD A and B; its function is the same as the INDEX# pin of FDC. It is pulled high internally. PD1 41 I/O PRINTER MODE: PD1 12ts Parallel port data bus bit 1. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. IN EXTENSION FDD MODE: TRAK02# ts TRAK02# This pin is for Extension FDD B; its function is the same as the TRAK0# pin of FDC. It is pulled high internally. EXTENSION. 2FDD MODE: TRAK02# This pin is for Extension FDD A and B; its function is the same as the TRAK0# pin of FDC. It is pulled high internally. PD2 40 I/O PRINTER MODE: PD2 12ts Parallel port data bus bit 2. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. IN EXTENSION FDD MODE: WP2# ts This pin is for Extension FDD B; its function is the same as the WP# pin of FDC. It is pulled high internally. EXTENSION. 2FDD MODE: WP2# This pin is for Extension FDD A and B; its function is the same as the WP# pin of FDC. It is pulled high internally. Publication Release Date: May 30, 2005 - 13 - Revision A1 W83697HF/ HG 5.3 Multi-Mode Parallel Port, continued SYMBOL PIN I/O FUNCTION PD3 39 I/O PRINTER MODE: PD3 12ts Parallel port data bus bit 3. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. IN EXTENSION FDD MODE: RDATA2# ts RDATA2# This pin is for Extension FDD B; its function is the same as the RDATA# pin of FDC. It is pulled high internally. EXTENSION 2FDD MODE: RDATA2# This pin is for Extension FDD A and B; its function is the same as the RDATA# pin of FDC. It is pulled high internally. PD4 38 I/O PRINTER MODE: PD4 12ts Parallel port data bus bit 4. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. EXTENSION FDD MODE: DSKCHG2# IN DSKCHG2# ts This pin is for Extension FDD B; the function of this pin is the same as the DSKCHG# pin of FDC. It is pulled high internally. EXTENSION 2FDD MODE: DSKCHG2# This pin is for Extension FDD A and B; this function of this pin is the same as the DSKCHG# pin of FDC. It is pulled high internally. PD5 37 I/O PRINTER MODE: PD5 12ts Parallel port data bus bit 5. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. - EXTENSION FDD MODE: This pin is a tri-state output. - EXTENSION 2FDD MODE: This pin is a tri-state output. PD6 36 I/O PRINTER MODE: PD6 12ts Parallel port data bus bit 6. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. - EXTENSION FDD MODE: This pin is a tri-state output. EXTENSION. 2FDD MODE: MOA2# OD MOA2# 12 This pin is for Extension FDD A; its function is the same as the MOA# pin of FDC. PD7 35 I/O PRINTER MODE: PD7 12ts Parallel port data bus bit 7. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. - EXTENSION FDD MODE: This pin is a tri-state output. OD EXTENSION 2FDD MODE: DSA2# 12 DSA2# This pin is for Extension FDD A; its function is the same as the DSA# pin of FDC. - 14 - W83697HF/ HG 5.4 Serial Port Interface SYMBOL PIN I/O FUNCTION CTSA# 47 IN Clear To Send. It is the modem control input. t CTSB# 55 The function of these pins can be tested by reading bit 4 of the handshake status register. DSRA# 48 IN Data Set Ready. An active low signal indicates the modem or t data set is ready to establish a communication link and transfer DSRB# 56 data to the UART. 49 O UART A Request To Send. An active low signal informs the 8 RTSA# modem or data set that the controller is ready to send data. During power-on reset, this pin is pulled down internally and is HEFRAS defined as HEFRAS, which provides the power-on value for CR26 INcd bit 6 (HEFRAS). A 4.7 kΩ is recommended if intends to pull up. (select 4EH as configuration I/O port′s address) 57 O UART B Request To Send. An active low signal informs the 8 RTSB# modem or data set that the controller is ready to send data. 50 O UART A Data Terminal Ready. An active low signal informs the 8 DTRA# modem or data set that the controller is ready to communicate. During power-on reset, this pin is pulled down internally and is PNPCSV# INcd defined as , which provides the power-on value for PNPCSV# CR24 bit 0 ( ). A 4.7 kΩ is recommended if intends to PNPCSV# pull up. (clear the default value of FDC, UARTs, and PRT) 58 O UART B Data Terminal Ready. An active low signal informs the 8 DTRB# modem or data set that controller is ready to communicate. SINA 51 IN Serial Input. It is used to receive serial data through the t SINB communication link. 59 52 O UART A Serial Output. It is used to transmit serial data out to the 8 SOUTA communication link. During power on reset , this pin is pulled down internally and is defined as PENROM#, which provides the power on value for PENROM# INcd CR24 bit 1. A 4.7kΩ is recommended if intends to pull up . SOUTB 61 O UART B Serial Output. During power-on reset, this pin is pulled 8 down internally and is defined as PEN48, which provides the PEN48 INcd power-on value for CR24 bit 6 (EN48). A 4.7 kΩ resistor is recommended if intends to pull up. DCDA# 53 IN Data Carrier Detect. An active low signal indicates the modem or t data set has detected a data carrier. DCDB# 62 RIA# 54 IN Ring Indicator. An active low signal indicates that a ring signal is t being received from the modem or data set. RIB# 63 Publication Release Date: May 30, 2005 - 15 - Revision A1 W83697HF/ HG 5.5 Infrared Port SYMBOL PIN I/O FUNCTION IRRX 64 INts Alternate Function Input: Infrared Receiver input. General purpose I/O port 3 bit 6. IRTX 65 O12 Alternate Function Output: Infrared Transmitter Output. General purpose I/O port 3 bit 7. CIRRX# 100 IN Consumer IR receiving input. This pin can Wake-Up system t from S5 cold. 5.6 Flash ROM Interface SYMBOL PIN I/O FUNCTION XA18-XA16 66-68 O12 Flash ROM interface Address[18:16] GP57-GP55 I/OD General purpose I/O port 5 bit7-5 12t XA15-XA10 69-74 O12 Flash ROM interface Address[15:10] GP47-GP42 I/OD General purpose I/O port 4 bit7-2 12t XA9-XA8 76-77 O12 Flash ROM interface Address[9:8] GP41-GP40 I/OD General purpose I/O port 4 bit1-0 12t XA7-XA0 78-85 O12 Flash ROM interface Address[7:0] I/OD GP37-GP30 12t General purpose I/O port 3 bit7-0 XD7-XD4 86-89 I/O12t Flash ROM interface Data Bus[7:4] I/OD GP27-GP24 12t General purpose I/O port 2 bit7-4 XD3-XD0 91-94 I/O12t Flash ROM interface Data Bus [3:0] GP23-GP20 I/OD General purpose I/O port 2 bit3-0 12t ROMCS# 95 O12 Flash ROM interface Chip Select I/OD 12t GP54 General purpose I/O port 5 bit4 MEMR# 96 O12 Flash ROM interface Memory Read Enable I/OD GP53 12t General purpose I/O port 5 bit3 MEMW# 97 O12 Flash ROM interface Memory Write Enable I/OD GP52 12t General purpose I/O port 5 bit2 - 16 - W83697HF/ HG 5.7 Hardware Monitor Interface SYMBOL PIN I/O FUNCTION CASEOPEN# 101 IN CASE OPEN. An active low signal from an external device when t case is opened. VBAT 102 Power Battery Voltage Input VTIN2 103 AIN Temperature sensor 2 input. It is used for CPU temperature detect. VTIN1 104 AIN Temperature sensor 1 input. It is used for system temperature detect. VREF 106 AOUT Reference Voltage Output. VCORE 107 AIN 0V to 4.096V FSR Analog Inputs. +3.3VIN 108 AIN 0V to 4.096V FSR Analog Inputs. +12VIN 109 AIN 0V to 4.096V FSR Analog Inputs. -12VIN 110 AIN 0V to 4.096V FSR Analog Inputs. -5VIN 111 AIN 0V to 4.096V FSR Analog Inputs. FANIO[2:1] 113- I/O 0V to +5V amplitude fan tachometer input. 12ts 114 Alternate Function: Fan on-off control output. These multifunctional pins can be programmable input or output. FANPWM[2:1] 115- O Fan speed control. Use the Pulse Width Modulation (PWM) 12 knowledge to control the Fan's RPM. 116 OVT# / 117 OD Over temperature Shutdown Output. It indicated the VTIN1 or 24 VTIN2 is over temperature limit. System Management Interrupt. OD SMI# 24 BEEP 118 OD8 Beep function for hardware monitor. This pin is low after system reset. Publication Release Date: May 30, 2005 - 17 - Revision A1 W83697HF/ HG 5.8 Game Port & MIDI Port SYMBOL PIN I/O FUNCTION MSI 119 INt MIDI serial data input . GP51 I/OD General purpose I/O port 5 bit 1. 12t WDTO# Alternate Function : O 12 Watch dog timer output. MSO 120 O12 MIDI serial data output. GP50 I/OD General purpose I/O port 5 bit 0. 12t PLED Alternate Function Output(Default) O 12 Power LED output, this signal is low after system reset. GPAS2 121 INcsu Active-low, Joystick I switch input 2. This pin has an internal pull-up resistor. (Default) General purpose I/O port 1 bit 7. GP17 I/OD 12csu GPBS2 122 INcsu Active-low, Joystick II switch input 2. This pin has an internal pull-up resistor. (Default) General purpose I/O port 1 bit 6. GP16 I/OD 12csu GPAY 123 I/OD Joystick I timer pin. this pin connect to Y positioning variable 12cs resistors for the Joystick. (Default) General purpose I/O port 1 bit 5. I/OD12cs GP15 GPBY 124 I/OD Joystick II timer pin. this pin connect to Y positioning variable 12cs resistors for the Joystick. (Default) General purpose I/O port 1 bit 4. I/OD12cs GP14 GPBX 125 I/OD Joystick II timer pin. this pin connect to X positioning variable 12cs resistors for the Joystick. (Default) General purpose I/O port 1 bit 3. GP13 I/OD12cs GPAX 126 I/OD Joystick I timer pin. this pin connect to X positioning variable 12cs resistors for the Joystick. (Default) General purpose I/O port 1 bit 2. I/OD12cs GP12 GPBS1 127 INcsu Active-low, Joystick II switch input 1. This pin has an internal pull-up resistor. (Default) General purpose I/O port 1 bit 1. GP11 I/OD 12csu GPAS1 128 INcsu Active-low, Joystick I switch input 1. This pin has an internal pull-up resistor. (Default) General purpose I/O port 1 bit 0. GP10 I/OD 12csu - 18 - W83697HF/ HG 5.9 POWER PINS SYMBOL PIN FUNCTION VCC 5, 45, 75, +5V power supply for the digital circuitry. VSB 99 +5V stand-by power supply for the digital circuitry. VCC3V 22 +3.3V power supply for driving 3V on host interface. AVCC 105 Analog VCC input. Internally supplier to all analog circuitry. AGND 112 Internally connected to all analog circuitry. The ground reference for all analog inputs.. GND 18, 60, 90, Ground. Publication Release Date: May 30, 2005 - 19 - Revision A1 W83697HF/ HG 6. HARDWARE MONITOR 6.1 General Description The W83697HF can be used to monitor several critical hardware parameters of the system, including power supply voltages, fan speeds, and temperatures, which are very important for a high-end computer system to work stable and properly. W83697HF provides LPC interface to access hardware . An 8-bit analog-to-digital converter (ADC) was built inside W83697HF. The W83697HF can simultaneously monitor 7 analog voltage inputs, 2 fan tachometer inputs, 2 remote temperature, one case-open detection signal. The remote temperature sensing can be performed by thermistors, or TM 2N3904 NPN-type transistors, or directly from Intel Deschutes CPU thermal diode output. Also the W83697HF provides: 2 PWM (pulse width modulation) outputs for the fan speed control; beep tone output for warning; SMI#(through serial IRQ) , OVT#, GPO# signals for system protection events. Through the application software or BIOS, the users can read all the monitored parameters of system from time to time. And a pop-up warning can be also activated when the monitored item was out of TM TM the proper/preset range. The application software could be Winbond's Hardware Doctor , or Intel LDCM (LanDesk Client Management), or other management application software. Also the users can set up the upper and lower limits (alarm thresholds) of these monitored parameters and to activate one programmable and maskable interrupts. An optional beep tone could be used as warning signal when the monitored parameters is out of the preset range. 6.2 Access Interface The W83697HF provides two interface for microprocessor to read/write hardware monitor internal registers. 6.2.1 LPC interface The first interface uses LPC Bus to access which the ports of low byte (bit2~bit0) are defined in the port 5h and 6h. The other higher bits of these ports is set by W83697HF itself. The general decoded address is set to port 295h and port 296h. These two ports are described as following: Port 295h: Index port. Port 296h: Data port. The register structure is showed as the Figure 9.1 - 20 - W83697HF/ HG Configuration Register 40h SMI# Status/Mask Registers 41h, 42h, 44h, 45h Fan Divisor Register 47h Device ID 48h Monitor Value Registers 20h~3Fh ISA ISA and Data Address 60h~7Fh (auto-increment) Bus Bus VID<4>/Device ID Port 5h 49h Temperature 2, 3 Serial Bus Address Index Register 4Ah Control Register 4Bh~4Dh Select Bank for 50h~5Fh Reg. 4Eh Winbond Vendor ID 4Fh BANK 0 R-T Table Value BEEP Control Register Port 6h Winbond Test Register 50h~58h Data Register BANK 1 Temperature 2 Control/Staus Registers 50h~56h BANK 2 Reserved 50h~56h BANK 4 Additional Control/Staus Registers 50h~5Ch BANK 5 Additional Limit Value & Value RAM 50h~57h Figure 9.1 : ISA interface access diagram Publication Release Date: May 30, 2005 - 21 - Revision A1 W83697HF/ HG 6.3 Analog Inputs The maximum input voltage of the analog pin is 4.096V because the 8-bit ADC has a 16mv LSB. Really, the application of the PC monitoring would most often be connected to power suppliers. The CPU V-core voltage ,+3.3V ,battery and 5VSB voltage can directly connected to these analog inputs. The +12V,-12V and -5V voltage inputs should be reduced a factor with external resistors so as to obtain the input range. As Figure 9.2 shows. Pin 100 VCOREA Pin 99 VCOREB Positive Inputs Pin 98 +3.3VIN Pin 97 AVCC(+5V) Pin 74 VBAT Pin 61 5VSB R1 +12VIN Pin 96 V1 8-bit ADC Positive Input R2 with 16mV LSB R3 N12VIN Pin 95 V2 Negative Input R5 N5VIN Pin 94 V3 R6 R4 R 10K, 1% VREF Pin 101 VTIN3 Pin 102 Typical Thermister Connectio Pin 103 VTIN2 R Pin 104 THM VTIN1 10K, 25 C **The Connections of VTIN1 and VTI are same as VTIN3 Figure. 9.2 - 22 - W83697HF/ HG 6.3.1 Monitor over 4.096V voltage: The input voltage +12VIN can be expressed as following equation. R 2 12VIN=× V 1 RR + 12 The value of R1 and R2 can be selected to 28K Ohms and 10K Ohms, respectively, when the input voltage V1 is 12V. The node voltage of +12VIN can be subject to less than 4.096V for the maximun input range of the 8-bit ADC. The Pin 97 is connected to the power supply VCC with +5V. There are two functions in this pin with 5V. The first function is to supply internal analog power in the W83697HF and the second function is that this voltage with 5V is connected to internal serial resistors to monitor the +5V voltage. The value of two serial resistors are 34K ohms and 50K ohms so that input voltage to ADC is 2.98V which is less than 4.096V of ADC maximum input voltage. The express equation can represent as follows. 50KΩ VV=× CC ≅ 29 . 8V in 50KK ΩΩ + 34 where VCC is set to 5V. The Pin 61 is connected to 5VSB voltage. W83697HF monitors this voltage and the internal two serial resistors are 17K Ω and 33K Ω so that input voltage to ADC is 3.3V which less than 4.096V of ADC maximum input voltage. 6.3.2 Monitor negative voltage: The negative voltage should be connected two series resistors and a positive voltage VREF (is equal to 3.6V). In the Figure 9.2, the voltage V2 and V3 are two negative voltage which they are -12V and - 5V respectively. The voltage V2 is connected to two serial resistors then is connected to another terminal VREF which is positive voltage. So as that the voltage node N12VIN can be obtain a posedge voltage if the scales of the two serial resirtors are carefully selected. It is recommanded from Winbond that the scale of two serial resistors are R3=232K ohms and R4=56K ohm. The input voltage of node N12VIN can be calculated by following equation. 232KΩ N12VIN=+() VREF V×( ) +V 22 232KK ΩΩ + 56 where VREF is equal 3.6V. If the V2 is equal to -12V then the voltage is equal to 0.567V and the converted hexdecimal data is set to 35h by the 8-bit ADC with 16mV-LSB.This monitored value should be converted to the real negative votage and the express equation is shown as follows. N12VIN −VREF × β V = 2 1− β Where β is 232K/(232K+56K). If the N2VIN is 0.567 then the V2 is approximately equal to -12V. Publication Release Date: May 30, 2005 - 23 - Revision A1 W83697HF/ HG The another negative voltage input V3 (approximate -5V) also can be evaluated by the similar method and the serial resistors can be selected with R5=120K ohms and R6=56K ohms by the Winbond recommended. The expression equation of V3 With -5V voltage is shown as follows. N5VIN −VREF × γ V = 3 1− γ Where the γ is set to 120K/(120K+56K). If the monitored ADC value in the N5VIN channel is 0.8635, VREF=3.6V and the parameter γ is 0.6818 then the negative voltage of V3 can be evalated to be -5V. 6.3.3 Temperature Measurement Machine The temperature data format is 8-bit two's-complement for sensor 2 and 9-bit two's-complement for sensor 1. The 8-bit temperature data can be obtained by reading the CR[27h]. The 9-bit temperature data can be obtained by reading the 8 MSBs from the Bank1 CR[50h] and the LSB from the Bank1 CR[51h] bit 7. The format of the temperature data is show in Table 1. 8-BIT DIGITAL OUTPUT 9-BIT DIGITAL OUTPUT TEMPERATURE 8-BIT BINARY 8-BIT HEX 9-BIT BINARY 9-BIT HEX +125°C 0111,1101 7Dh 0,1111,1010 0FAh +25°C 0001,1001 19h 0,0011,0010 032h +1°C 0000,0001 01h 0,0000,0010 002h +0.5°C - - 0,0000,0001 001h +0°C 0000,0000 00h 0,0000,0000 000h -0.5°C - - 1,1111,1111 1FFh -1°C 1111,1111 FFh 1,1111,1110 1FFh -25°C 1110,0111 E7h 1,1100,1110 1CEh -55°C 1100,1001 C9h 1,1001,0010 192h Table 2. 6.3.3.1. Monitor temperature from thermistor: The W83697HF can connect three thermistors to measure three different envirment temperature. The specification of thermistor should be considered to (1) β value is 3435K, (2) resistor value is 10K ohms at 25°C. In the Figure 9.2, the themistor is connected by a serial resistor with 10K Ohms, then connect to VREF (Pin 101). TM 6.3.3.2. Monitor temperature from Pentium II thermal diode or bipolar transistor 2N3904 TM The W83697HF can alternate the thermistor to Pentium II (Deschutes) thermal diode interface or TM transistor 2N3904 and the circuit connection is shown as Figure 9.3. The pin of Pentium II D- is connected to power supply ground (GND) and the pin D+ is connected to pin VTINx in the W83697HF. The resistor R=30K ohms should be connected to VREF to supply the diode bias current and the bypass capacitor C=3300pF should be added to filter the high frequency noise. The transistor 2N3904 should be connected to a form with a diode, that is, the Base (B) and Collector (C) in the 2N3904 should be tied togeter to act as a thermal diode. - 24 - W83697HF/ HG VREF R=30K, 1% Bipolar Transistor Temperature Sensor VTINx C=3300pF C B 2N3904 W83627HF E R=30K, 1% OR Pentium II CPU D+ VTINx Therminal C=3300pF Diode D- Figure 9.3 6.4 FAN Speed Count and FAN Speed Control 6.4.1 Fan speed count Inputs are provides for signals from fans equipped with tachometer outputs. The level of these signals should be set to TTL level, and maximum input voltage can not be over +5.5V. If the input signals from the tachometer outputs are over the VCC, the external trimming circuit should be added to reduce the voltage to obtain the input specification. The normal circuit and trimming circuits are shown as Figure 9.4. Determine the fan counter according to: 6 13 . 5 ×10 Count = RPM × Divisor In other words, the fan speed counter has been read from register CR28 or CR29 or CR2A, the fan speed can be evaluated by the following equation. 6 13 . 5 ×10 RPM = Count × Divisor The default divisor is 2 and defined at CR47.bit7~4, CR4B.bit7~6, and Bank0 CR5D.bit5~7 which are three bits for divisor. That provides very low speed fan counter such as power supply fan. The followed table is an example for the relation of divisor, PRM, and count. Publication Release Date: May 30, 2005 - 25 - Revision A1 W83697HF/ HG NOMINAL TIME PER TIME FOR DIVISOR COUNTS 70% RPM PRM REVOLUTION 70% 1 8800 6.82 ms 153 6160 9.74 ms 2 (default) 4400 13.64 ms 153 3080 19.48 ms 4 2200 27.27 ms 153 1540 38.96 ms 8 1100 54.54 ms 153 770 77.92 ms 16 550 109.08 ms 153 385 155.84 ms 32 275 218.16 ms 153 192 311.68 ms 64 137 436.32 ms 153 96 623.36 ms 128 68 872.64 ms 153 48 1246.72 ms Table 1. +12V +5V +12V Pull-up resister Pull-up resister 4.7K Ohms 4.7K Ohms diode diode +12V +12V 14K~39K Fan Input Fan Input FAN Out FAN Out Pin 111-113 Pin 111-113 GND GND 10K W83627HF W83627HF FAN FAN Connector Connector Fan with Tach Pull-Up to +5V Fan with Tach Pull-Up to +12V, or Totem-Pole Output and Register Attenuator +12V +12V Pull-up resister < 1K diode diode Pull-up resister or totem-pole output > 1K +12V +12V Fan Input FAN Out FAN Out Pin 111-113 Pin 111-113 Fan Input > 1K GND GND 3.9V Zener 3.9V Zener W83627HF W83627HF FAN FAN Connector Connector Fan with Tach Pull-Up to +12V, or Totem-Pole Fan with Tach Pull-Up to +12V and Zener Clamp Output and Zener Clamp Figure 9.4 - 26 - W83697HF/ HG 6.4.2 Fan speed control The W83697HF provides 2 sets for fan PWM speed control. The duty cycle of PWM can be programmed by a 8-bit registers which are defined in the Bank0 CR5A and CR5B. The default duty cycle is set to 100%, that is, the default 8-bit registers is set to FFh. The expression of duty can be represented as follows. Programmed 8- bit Register Value Duty−= cycle(%) × 100% 255 The PWM clock frequency also can be program and defined in the Bank0.CR5C . The application circuit is shown as follows. +12V R1 R2 PNP Transistor D G PWM Clock Input NMOS S + C FAN - Figure 9.5 Publication Release Date: May 30, 2005 - 27 - Revision A1 W83697HF/ HG 6.5 SMI# interrupt mode 6.5.1 Voltage SMI# mode : SMI# interrupt for voltage is Two-Times Interrupt Mode. Voltage exceeding high limit or going below low limit will causes an interrupt if the previous interrupt has been reset by reading all the interrupt Status Register. (Figure 9.6 ) 6.5.2 Fan SMI# mode : SMI# interrupt for fan is Two-Times Interrupt Mode. Fan count exceeding the limit, or exceeding and then going below the limit, will causes an interrupt if the previous interrupt has been reset by reading all the interrupt Status Register. (Figure 9.7 ) High limit Fan Count limit Low limit SMI# SMI# ** * * * * *Interrupt Reset when Interrupt Status Registers are read Figure 9.6 Figure 9.7 - 28 - W83697HF/ HG 6.5.3 The W83697HF temperature sensor 1 SMI# interrupt has two modes: (1) Comparator Interrupt Mode Setting the T (Temperature Hysteresis) limit to 127°C will set temperature sensor 1 SMI# to HYST the Comparator Interrupt Mode. Temperature exceeds T (Over Temperature) Limit causes an O interrupt and this interrupt will be reset by reading all the Interrupt Status Register. Once an interrupt event has occurred by exceeding T , then reset, if the temperature remains above the O T , the interrupt will occur again when the next conversion has completed. If an interrupt event O has occurred by exceeding T and not reset, the interrupts will not occur again. The interrupts O will continue to occur in this manner until the temperature goes below T . (Figure 9.8 ) O (2) Two-Times Interrupt Mode Setting the T lower than T will set temperature sensor 1 SMI# to the Two-Times Interrupt HYST O Mode. Temperature exceeding T causes an interrupt and then temperature going below T O HYST will also cause an interrupt if the previous interrupt has been reset by reading all the interrupt Status Register. Once an interrupt event has occurred by exceeding T , then reset, if the O temperature remains above the T , the interrupt will not occur. (Figure 9.9 ) HYST T HYST 127'C T T OI OI T HYST SMI# SMI# ** ** * * * *Interrupt Reset when Interrupt Status Registers are read Figure 9.8 Figure 9.9 Publication Release Date: May 30, 2005 - 29 - Revision A1 W83697HF/ HG 6.5.4 The W83697HF temperature sensor 2 SMI# interrupt has two modes and it is programmed at CR[4Ch] bit 6. (1) Comparator Interrupt Mode Temperature exceeding T causes an interrupt and this interrupt will be reset by reading all the O Interrupt Status Register. Once an interrupt event has occurred by exceeding T , then reset, if O the temperature remains above the T , the interrupt will occur again when the next conversion HYST has completed. If an interrupt event has occurred by exceeding T and not reset, the interrupts O will not occur again. The interrupts will continue to occur in this manner until the temperature goes below T . ( Figure 9.10 ) HYST (2) Two-Times Interrupt Mode Temperature exceeding T causes an interrupt and then temperature going below T will also O HYST cause an interrupt if the previous interrupt has been reset by reading all the interrupt Status Register. Once an interrupt event has occurred by exceeding T , then reset, if the temperature O remains above the T , the interrupt will not occur. (Figure 9.11 ) HYST T T OI OI T T HYST HYST SMI# SMI# ** ** * * * * *Interrupt Reset when Interrupt Status Registers are read Figure 9.10 Figure 9.11 - 30 - W83697HF/ HG 6.6 OVT# interrupt mode The OVT# signal is only related with temperature sensor 2 (VTIN2 ). 6.6.1 The W83697HF temperature sensor 2 Over-Temperature (OVT#) has the following modes (1) Comparator Mode : Setting Bank1/2 CR[52h] bit 2 to 0 will set OVT# signal to comparator mode. Temperature exceeding T causes the OVT# output activated until the temperature is less than T . ( Figure O HYST 9.12) (2) Interrupt Mode: Setting Bank1/2 CR[52h] bit 2 to 1 will set OVT# signal to interrupt mode. Setting Temperature exceeding T causes the OVT# output activated indefinitely until reset by reading temperature O sensor 2 or sensor 3 registers. Temperature exceeding T , then OVT# reset, and then O temperature going below T will also cause the OVT# activated indefinitely until reset by HYST reading temperature sensor2 or sensor 3 registers. Once the OVT# is activated by exceeding T , then reset, if the temperature remains above T , the OVT# will not be activated O HYST again.( Figure 9.12) To T HYST OVT# (Comparator Mode; default) OVT# ** * * (Interrupt Mode) *Interrupt Reset when Temperature 2/3 is read Publication Release Date: May 30, 2005 - 31 - Revision A1 W83697HF/ HG 6.7 REGISTERS AND RAM Address Register (Port x5h) Data Port: Port x5h Power on Default Value 00h Attribute: Bit 6:0 Read/write , Bit 7: Read Only Size: 8 bits 7 6 5 4 3 2 1 0 Data Bit7: Read Only The logical 1 indicates the device is busy because of a Serial Bus transaction or another LPC bus transaction. With checking this bit, multiple LPC drivers can use W83697HF hardware monitor without interfering with each other or a Serial Bus driver. It is the user's responsibility not to have a Serial Bus and LPC bus operations at the same time. This bit is: Set: with a write to Port x5h or when a Serial Bus transaction is in progress. Reset: with a write or read from Port x6h if it is set by a write to Port x5h. Bit 6-0: Read/Write Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Busy Address Pointer (Power On default 00h) (Power On default A6 A5 A4 A3 A2 A1 A0 0) - 32 - W83697HF/ HG Address Pointer Index (A6-A0) POWER ON VALUE OF A6-A0 REGISTERS AND RAM REGISTERS: IN NOTES IN HEX BINARY Configuration Register 40h 00001000 Auto-increment to the address of Interrupt Status Register 1 41h 00000000 Interrupt Status Register 2 after a read or write to Port x6h. Interrupt Status Register 2 42h 00000000 Auto-increment to the address of SMI#Ý Mask Register 1 43h 00000000 SMIÝ Mask Register 2 after a read or write to Port x6h. SMIÝ Mask Register 2 44h 00000000 AUTO-INCREMENT TO THE ADDRESS OF NMI MASK NMI Mask Register 1 45h 00000000 REGISTER 2 AFTER A READ OR WRITE TO PORT X6H NMI Mask Register 2 46h 01000000 Fan Divisor Register 47h <7:4> = 0101; Reserved 48h Device ID Register 49h <7:1> = 0000001 Reserved 4Ah Reserved 4Bh SMI#/OVT# Property 4Ch <7:0> = 00000000 Select Register FAN IN/OUT and BEEP 4Dh <7:0> = 00010101 Control Register <7> = 1 ; Register 50h-5Fh Bank 4Eh <6:3> = Reserved ; Select Register <2:0> = 000 <7:0> = 01011100 Winbond Vendor ID (High Byte) 4Fh Register <7:0> = 10100011 (Low Byte) Publication Release Date: May 30, 2005 - 33 - Revision A1 W83697HF/ HG Address Pointer Index (A6-A0), continued POWER ON VALUE OF A6-A0 REGISTERS AND RAM REGISTERS: IN NOTES IN HEX BINARY Auto-increment to the next POST RAM 00-1Fh location after a read or write to Port x6h and stop at 1Fh. Value RAM 20-3Fh Auto-increment to the next Value RAM 60-7Fh location after a read or write to Port x6h and stop at 7Fh. Bank1 Temperature 2 Registers 50h-56h Bank2 Reserved 50h-56h Bank4 Additional Configuration 50h- Registers 5Dh - 34 - W83697HF/ HG Data Register (Port x6h) Data Port: Port x6h Power on Default Value 00h Attribute: Read/write Size: 8 bits 7 6 5 4 3 2 1 0 Data Bit 7-0: Data to be read from or to be written to RAM and Register. Configuration Register  Index 40h Register Location: 40h Power on Default Value 01h Attribute: Read/write Size: 8 bits 7 6 5 4 3 2 1 0 START SMI#Enable RESERVED INT_Clear RESERVED RESERVED RESERVED INITIALIZATION Bit 7: A one restores power on default value to all registers except the Serial Bus Address register. This bit clears itself since the power on default is zero. Bit 6: Reserced Bit 5: Reserved Bit 4: Reserved Bit 3: A one disables the SMI# output without affecting the contents of Interrupt Status Registers. The device will stop monitoring. It will resume upon clearing of this bit. Bit 2: Reserved Bit 1: A one enables the SMI# Interrupt output. Bit 0: A one enables startup of monitoring operations, a zero puts the part in standby mode. Note: The outputs of Interrupt pins will not be cleared if the user writes a zero to this location after an interrupt has occurred unlike "INT_Clear'' bit. Publication Release Date: May 30, 2005 - 35 - Revision A1 W83697HF/ HG Interrupt Status Register 1 Index 41h Register Location: 41h Power on Default Value 00h Attribute: Read Only Size: 8 bits 7 6 5 4 3 2 1 0 VCORE Reserved +3.3VIN AVCC TEMP1 TEMP2 FAN1 FAN2 Bit 7: A one indicates the fan count limit of FAN2 has been exceeded. Bit 6: A one indicates the fan count limit of FAN1 has been exceeded. Bit 5: A one indicates a High limit of VTIN2 has been exceeded from temperature sensor 2. Bit 4: A one indicates a High limit of VTIN1 has been exceeded from temperature sensor 1. Bit 3: A one indicates a High or Low limit of +5VIN has been exceeded. Bit 2: A one indicates a High or Low limit of +3.3VIN has been exceeded. Bit 1: Reserved Bit 0: A one indicates a High or Low limit of VCORE has been exceeded. Interrupt Status Register 2  Index 42h Register Location: 42h Power on Default Value 00h Attribute: Read Only Size: 8 bits 7 6 5 4 3 2 1 0 +12VIN -12VIN -5VIN Reserved CaseOpen Reserved Reserved Reserved - 36 - W83697HF/ HG Bit 7-6:Reserved.This bit should be set to 0. Bit 5: Reserved. Bit 4: A one indicates case has been opened. Bit 3: Reserved. Bit 2: A one indicates a High or Low limit of -5VIN has been exceeded. Bit1: A one indicates a High or Low limit of -12VIN has been exceeded. Bit0: A one indicates a High or Low limit of +12VIN has been exceeded. SMI# Mask Register 1  Index 43h Register Location: 43h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 VCORE Reserved +3.3VIN AVCC TEMP1 TEMP2 FAN1 FAN2 Bit 7-0: A one disables the corresponding interrupt status bit for SMI interrupt. SMI# Mask Register 2  Index 44h Register Location: 44h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 +12VIN -12VIN -5VIN Reserved CaseOpen Reserved Reserved Reserved Bit 7-6: Reserved. This bit should be set to 0. Bit 5-0: A one disables the corresponding interrupt status bit for SMI interrupt. Publication Release Date: May 30, 2005 - 37 - Revision A1 W83697HF/ HG Reserved Register  Index 45h Chassis Clear Register -- Index 46h Register Location: 46h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Chassis Clear Bit 7: Set 1 , clear case open event. This bit self clears after clearing case open event. Bit 6-0:Reserved. This bit should be set to 0. Fan Divisor Register  Index 47h Register Location: 47h Power on Default Value 5fh Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 Reserved Reserved Reserved Reserved FAN1DIV_B0 FAN1DIV_B1 FAN2DIV_B0 FAN2DIV_B1 Bit 7-6: FAN2 Speed Control. Bit 5-4: FAN1 Speed Control. Bit 3-0: Reserved Note : Please refer to Bank0 CR[5Dh] , Fan divisor table. - 38 - W83697HF/ HG Value RAM  Index 20h- 3Fh or 60h - 7Fh (auto-increment) ADDRESS A6- ADDRESS A6-A0 WITH DESCRIPTION A0 AUTO-INCREMENT 20h 60h VCORE reading 21h 61h Reserved 22h 62h +3.3VIN reading 23h 63h AVCC(+5V) reading 24h 64h +12VIN reading 25h 65h -12VIN reading 26h 66h -5VIN reading 27h 67h Temperature sensor 1 reading FAN1 reading 28h 68h Note: This location stores the number of counts of the internal clock per revolution. FAN2 reading 29h 69h Note: This location stores the number of counts of the internal clock per revolution. 2Bh 6Bh VCORE High Limit 2Ch 6Ch VCORE Low Limit 2Dh 6Dh Reserved 2Eh 6Eh Reserved 2Fh 6Fh +3.3VIN High Limit 30h 70h +3.3VIN Low Limit 31h 71h AVCC(+5V) High Limit 32h 72h AVCC(+5V) Low Limit 33h 73h +12VIN High Limit 34h 74h +12VIN Low Limit 35h 75h -12VIN High Limit Publication Release Date: May 30, 2005 - 39 - Revision A1 W83697HF/ HG Value RAM  Index 20h- 3Fh or 60h - 7Fh (auto-increment), continued ADDRESS A6- ADDRESS A6-A0 WITH DESCRIPTION A0 AUTO-INCREMENT 36h 76h -12VIN Low Limit 37h 77h -5VIN High Limit 38h 78h -5VIN Low Limit 39h 79h Temperature sensor 1 (VTIN1) High Limit 3Ah 7Ah Temperature sensor 1 (VTIN1) Hysteresis Limit FAN1 Fan Count Limit 3Bh 7Bh Note: It is the number of counts of the internal clock for the Low Limit of the fan speed. FAN2 Fan Count Limit 3Ch 7Ch Note: It is the number of counts of the internal clock for the Low Limit of the fan speed. 3Dh 7Dh Reserved. 3E- 3Fh 7E- 7Fh Reserved Setting all ones to the high limits for voltages and fans (0111 1111 binary for temperature) means interrupts will never be generated except the case when voltages go below the low limits. Device ID Register - Index 49h Register Location: 49h Power on Default Value <7:1> is 000,0001 binary Size: 8 bits 7 6 5 4 3 2 1 0 Reserved DID<6:0> Bit 7-1: Read Only - Device ID<6:0> Bit 0 : Reserved Reserved - Index 4Bh - 40 - W83697HF/ HG SMI#/OVT# Property Select Register- Index 4Ch Register Location: 4Ch Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 Reserved Reserved OVTPOL DIS_OVT Reserved Reserved T2_INTMode Reserved Bit 7: Reserved. User Defined. Bit6: Set to 1, the SMI# output type of Temperature 2(VTIN2) is set to Comparator Interrupt mode. Set to 0, the SMI# output type is set to Two-Times Interrupt mode. (default 0) Bit5: Reserved. User Defined. Bit 4: Reserved Bit 3: Disable temperature sensor 2 over-temperature (OVT) output if set to 1. Default 0, enable OVT# (Temp 2) output through pin OVT#. Bit 2: Over-temperature polarity. Write 1, OVT# active high. Write 0, OVT# active low. Default 0. Bit 1: Reserved. Bit 0: OVT# mode select. Set 1 to ACPI Mode, Set 0 to Comparator or Interrupt mode. Default 0. FAN IN/OUT and BEEP Control Register- Index 4Dh Register Location: 4Dh Power on Default Value 15h Attribute: Read/Write Size: 8 bits Publication Release Date: May 30, 2005 - 41 - Revision A1 W83697HF/ HG 7 6 5 4 3 2 1 0 FANINC1 FANOPV1 FANINC2 FANOPV2 Reserved Reserved Reserved Reserved Bit 7~4: Reserved. Bit 3: FAN 2 output value if FANINC2 sets to 0. Write 1, then pin 113 always generate logic high signal. Write 0, pin 113 always generates logic low signal. This bit default 0. Bit 2: FAN 2 Input Control. Set to 1, pin 113 acts as FAN clock input, which is default value. Set to 0, this pin 113 acts as FAN control signal and the output value of FAN control is set by this register bit 3. Bit 1: FAN 1 output value if FANINC1 sets to 0. Write 1, then pin 114 always generate logic high signal. Write 0, pin 114 always generates logic low signal. This bit default 0. Bit 0: FAN 1 Input Control. Set to 1, pin 114 acts as FAN clock input, which is default value. Set to 0, this pin 114 acts as FAN control signal and the output value of FAN control is set by this register bit 1. Register 50h ~ 5Fh Bank Select Register - Index 4Eh Register Location: 4Eh Power on Default Value 80h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 BANKSEL0 BANKSEL1 BANKSEL2 Reserved Reserved Reserved Reserved HBACS Bit 7: HBACS- High byte access. Set to 1, access Register 4Fh high byte register. Set to 0, access Register 4Fh low byte register. Default 1. Bit 6-3: Reserved. This bit should be set to 0. Bit 2-0: Index ports 0x50~0x5F Bank select. - 42 - W83697HF/ HG Winbond Vendor ID Register - Index 4Fh (No Auto Increase) Register Location: 4Fh Power on Default Value <15:0> = 5CA3h Attribute: Read Only Size: 16 bits 15 8 7 0 VIDH VIDL Bit 15-8: Vendor ID High Byte if CR4E.bit7=1.Default 5Ch. Bit 7-0: Vendor ID Low Byte if CR4E.bit7=0. Default A3h. Winbond Test Register -- Index 50h - 55h (Bank 0) BEEP Control Register 1-- Index 56h (Bank 0) Register Location: 56h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 EN_VC_BP Reserved EN_V33_BP EN_AVCC_BP EN_T1_BP EN_T2_BP EN_FAN1_BP EN_FAN2_BP Bit 7: Enable BEEP Output from FAN 2 if the monitor value exceed the limit value. Write 1, enable BEEP output, which is default value. Bit 6: Enable BEEP Output from FAN 1 if the monitor value exceed the limit value. Write 1, enable BEEP output, which is default value. Bit 5: Enable BEEP Output from Temperature Sensor 2 if the monitor value exceed the limit value. Write 1, enable BEEP output. Default 0 Publication Release Date: May 30, 2005 - 43 - Revision A1 W83697HF/ HG Bit 4: Enable BEEP output for Temperature Sensor 1 if the monitor value exceed the limit value. Write 1, enable BEEP output. Default 0 Bit 3: Enable BEEP output from AVCC (+5V), Write 1, enable BEEP output if the monitor value exceed the limits value. Default 0, that is disable BEEP output. Bit 2: Enable BEEP output from +3.3V. Write 1, enable BEEP output, which is default value. Bit 1: Reserved Bit 0: Enable BEEP Output from VCORE if the monitor value exceed the limits value. Write 1, enable BEEP output, which is default value BEEP Control Register 2-- Index 57h (Bank 0) Register Location: 57h Power on Default Value 80h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 EN_V12_BP EN_NV12_BP EN_NV5_BP Reserved EN_CASO_BP Reserved Reserved EN_GBP Bit 7: Enable Global BEEP. Write 1, enable global BEEP output. Default 1. Write 0, disable all BEEP output. Bit 6: Reserved. This bit should be set to 0. Bit5: Reserved Bit 4: Enable BEEP output for case open if case opend. Write 1, enable BEEP output. Default 0. Bit 3: Reserved Bit 2: Enable BEEP output from -5V, Write 1, enable BEEP output if the monitor value exceed the limits value. Default 0, that is disable BEEP output. Bit 1: Enable BEEP output from -12V, Write 1, enable BEEP output if the monitor value exceed the limits value. Default 0, that is disable BEEP output. Bit 0: Enable BEEP output from +12V, Write 1, enable BEEP output if the monitor value exceed the limits value. Default 0, that is disable BEEP output. - 44 - W83697HF/ HG Chip ID -- Index 58h (Bank 0) Register Location: 58h Power on Default Value 60h Attribute: Read Only Size: 8 bits 7 6 5 4 3 2 1 0 CHIPID Bit 7: Winbond Chip ID number. Read this register will return 60h. Register -- Index 59h (Bank 0) Register Location: 59h Power on Default Value <7>=0 and <6:4> = 111 and <3:0> = 0000 Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 Reserved Reserved Reserved Reserved SELPIIV1 SELPIIV2 Reserved Reserved Bit 7-6: Reserved Bit 5: Temperature sensor diode 2. Set to 1, select Pentium II compatible Diode. Set to 0 to select 2N3904 Bipolar mode. Bit 4: Temperature sensor diode 1. Set to 1, select Pentium II compatible Diode. Set to 0 to select 2N3904 Bipolar mode. Bit 3-0: Reserved Publication Release Date: May 30, 2005 - 45 - Revision A1 W83697HF/ HG Reserved -- Index 5Ah (Bank 0) Reserved -- Index 5Bh (Bank 0) Reserved -- Index 5Ch (Bank 0) ACPI Temperature Increment Register -- Index 5Fh (Bank 0) Register Location: 5Fh Power on Default Value <7:0> = 0x00 Attribute: Read/Write Size: 7 bits Bit Name Attribute Description 7 Reserved Reserved Reserved 6-0 DIFFREG[6:0] Read/Write ACPI Temperature Increment Register. If set to this register to non-zero value, the OVT# signal will be activated at pointer of the temperature of times of DIFFREG. VBAT Monitor Control Register -- Index 5Dh (Bank 0) Register Location: 5Dh Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 EN_VBAT_MNT DIODES1 DIODES2 Reserved Reserved FANDIV1_B2 FANDIV2_B2 Reserved Bit 7: Reserved. Bit 6: Fan2 divisor Bit 2. Bit 5: Fan1 divisor Bit 2. Bit 4 –3 : Reserved. Bit 2: Sensor 2 type selection. Set to 1, select bipolar sensor. Set to 0, select thermistor sensor. Bit 1: Sensor 1 type selection. Set to 1, select bipolar sensor. Set to 0, select thermistor sensor. Bit 0: Set to 1, enable battery voltage monitor. Set to 0, disable battery voltage monitor. If enable this bit, the monitor value is value after one monitor cycle. Note that the monitor cycle time is at least 300ms for W83697HF hardware monitor. - 46 - W83697HF/ HG Fan divisor table : BIT 2 BIT 1 BIT 0 FAN DIVISOR BIT 2 BIT 1 BIT 0 FAN DIVISOR 0 0 0 1 1 0 0 16 0 0 1 2 1 0 1 32 0 1 0 4 1 1 0 64 0 1 1 8 1 1 1 128 Reserved Register -- 5Eh (Bank 0) Reserved Register -- 5Fh (Bank 0) Temperature Sensor 2 Temperature (High Byte) Register - Index 50h (Bank 1) Register Location: 50h Attribute: Read Only Size: 8 bits 7 6 5 4 3 2 1 0 TEMP2<8:1> ° Bit 7: Temperature <8:1> of sensor 2, which is high byte, means 1 C. Temperature Sensor 2 Temperature (Low Byte) Register - Index 51h (Bank 1) Register Location: 51h Attribute: Read Only Size: 8 bits 7 6 5 4 3 2 1 0 Reserved TEMP2<0> ° Bit 7: Temperature <0> of sensor2, which is low byte, means 0.5 C. Bit 6-0: Reserved. Publication Release Date: May 30, 2005 - 47 - Revision A1 W83697HF/ HG Temperature Sensor 2 Configuration Register - Index 52h (Bank 1) Register Location: 52h Power on Default Value 00h Size: 8 bits 7 6 5 4 3 2 1 0 STOP2 INTMOD Reserved FAULT FAULT Reserved Reserved Reserved Bit 7-5: Read - Reserved. This bit should be set to 0.   Bit 4-3: Read/Write - Number of faults to detect before setting OVT# output to avoid false tripping due to noise. Bit 2: Read - Reserved. This bit should be set to 0. Bit 1: Read/Write - OVT# Interrupt mode select. This bit default is set to 0, which is compared mode. When set to 1, interrupt mode will be selected. Bit 0: Read/Write - When set to 1 the sensor will stop monitor. Temperature Sensor 2 Hysteresis (High Byte) Register - Index 53h (Bank 1) Register Location: 53h Power on Default Value 4Bh Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 THYST2<8:1> Bit 7-0: Temperature hysteresis bit 8-1, which is High Byte. The temperature default 75 degree C. - 48 - W83697HF/ HG Temperature Sensor 2 Hysteresis (Low Byte) Register - Index 54h (Bank 1) Register Location: 54h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 Reserved THYST2<0> Bit 7: Hysteresis temperature bit 0, which is low Byte. Bit 6-0: Reserved. Temperature Sensor 2 Over-temperature (High Byte) Register - Index 55h (Bank 1) Register Location: 55h Power on Default Value 50h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 TOVF2<8:1> Bit 7-0: Over-temperature bit 8-1, which is High Byte. The temperature default 80 degree C. Publication Release Date: May 30, 2005 - 49 - Revision A1 W83697HF/ HG Temperature Sensor 2 Over-temperature (Low Byte) Register - Index 56h (Bank 1) Register Location: 56h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 Reserved TOVF2<0> Bit 7: Over-temperature bit 0, which is low Byte. Bit 6-0: Reserved. Interrupt Status Register 3 -- Index 50h (BANK4) Register Location: 50h Power on Default Value 00h Attribute: Read Only Size: 8 bits 7 6 5 4 3 2 1 0 5VSB VBAT Reserved Reserved Reserved Reserved Reserved Reserved Bit 7-2: Reserved. Bit 1: A one indicates a High or Low limit of VBAT has been exceeded. Bit 0: A one indicates a High or Low limit of 5VSB has been exceeded. - 50 - W83697HF/ HG SMI# Mask Register 3 -- Index 51h (BANK 4) Register Location: 51h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 5VSB VBAT Reserved Reserved Reserved Reserved Reserved Reserved Bit 7-2: Reserved. Bit 1: A one disables the corresponding interrupt status bit for SMI interrupt. Bit 0: A one disables the corresponding interrupt status bit for SMI interrupt. Reserved Register -- Index 52h (Bank 4) BEEP Control Register 3-- Index 53h (Bank 4) Register Location: 53h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 EN_5VSB_BP EN_VBAT_BP Reserved Reserved Reserved EN_USER_BP Reserved Reserved Bit 7-6: Reserved. Bit 5: User define BEEP output function. Write 1, the BEEP is always active. Write 0, this function is inactive. (Default 0) Bit 4-2: Reserved. Bit 1: Enable BEEP output from VBAT. Write 1, enable BEEP output, which is default value. Bit 0: Enable BEEP Output from 5VSB. Write 1, enable BEEP output, which is default value. Publication Release Date: May 30, 2005 - 51 - Revision A1 W83697HF/ HG Temperature Sensor 1 Offset Register -- Index 54h (Bank 4) Register Location: 54h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 OFFSET1<7:0> Bit 7-0: Temperature 1 base temperature. The temperature is added by both monitor value and offset value. Temperature Sensor 2 Offset Register -- Index 55h (Bank 4) Register Location: 55h Power on Default Value 00h Attribute: Read/Write Size: 8 bits 7 6 5 4 3 2 1 0 OFFSET2<7:0> Bit 7-0: Temperature 2 base temperature. The temperature is added by both monitor value and offset value. Reserved Register -- Index 57h--58h - 52 - W83697HF/ HG Real Time Hardware Status Register I -- Index 59h (Bank 4) Register Location: 59h Power on Default Value 00h Attribute: Read Only Size: 8 bits 7 6 5 4 3 2 1 0 VCORE_STS Reserved +3.3VIN_STS AVCC_STS TEMP1_STS TEMP2_STS FAN1_STS FAN2_STS Bit 7: FAN 2 Status. Set 1, the fan speed counter is over the limit value. Set 0, the fan speed counter is in the limit range. Bit 6: FAN 1 Status. Set 1, the fan speed counter is over the limit value. Set 0, the fan speed counter is in the limit range. Bit 5: Temperature sensor 2 Status. Set 1, the voltage of temperature sensor is over the limit value. Set 0, the voltage of temperature sensor is in the limit range. Bit 4: Temperature sensor 1 Status. Set 1, the voltage of temperature sensor is over the limit value. Set 0, the voltage of temperature sensor is in the limit range. Bit 3: AVCC Voltage Status. Set 1, the voltage of +5V is over the limit value. Set 0, the voltage of +5V is in the limit range. Bit 2: +3.3V Voltage Status. Set 1, the voltage of +3.3V is over the limit value. Set 0, the voltage of +3.3V is in the limit range. Bit 1: Reserved Bit 0: VCORE Voltage Status. Set 1, the voltage of VCORE A is over the limit value. Set 0, the voltage of VCORE A is in the limit range. Real Time Hardware Status Register II -- Index 5Ah (Bank 4) Register Location: 5Ah Power on Default Value 00h Attribute: Read Only Size: 8 bits Publication Release Date: May 30, 2005 - 53 - Revision A1 W83697HF/ HG 7 6 5 4 3 2 1 0 +12VIN_STS -12VIN_STS -5VIN_STS Reserved CASE_STS Reserved Reserved Reserved Bit 7-6: Reserved Bit 5: Reserved Bit 4: Case Open Status. Set 1, the case open sensor is sensed the high value. Set 0 Bit 3: Reserved Bit 2: -5V Voltage Status. Set 1, the voltage of -5V is over the limit value. Set 0, the voltage of -5V is during the limit range. Bit 1: -12V Voltage Status. Set 1, the voltage of -12V is over the limit value. Set 0, the voltage of - 12V is during the limit range. Bit 0: +12V Voltage Status. Set 1, the voltage of +12V is over the limit value. Set 0, the voltage of +12V is in the limit range. Real Time Hardware Status Register III -- Index 5Bh (Bank 4) Register Location: 5Bh Power on Default Value 00h Attribute: Read Only Size: 8 bits 7 6 5 4 3 2 1 0 5VSB_STS VBAT_STS Reserved Reserved Reserved Reserved Reserved Reserved Bit 7-2: Reserved. Bit 1: VBAT Voltage Status. Set 1, the voltage of VBAT is over the limit value. Set 0, the voltage of VBAT is during the limit range. Bit 0: 5VSB Voltage Status. Set 1, the voltage of 5VSB is over the limit value. Set 0, the voltage of 5VSB is in the limit range. - 54 - W83697HF/ HG Reserved Register -- Index 5Ch (Bank 4) Reserved Register -- Index 5Dh (Bank 4) Value RAM 2 Index 50h - 5Ah (auto-increment) (BANK 5) ADDRESS A6-A0 DESCRIPTION AUTO-INCREMENT 50h 5VSB reading 51h VBAT reading 52h Reserved 53h Reserved 54h 5VSB High Limit 55h 5VSB Low Limit. 56h VBAT High Limit 57h VBAT Low Limit Winbond Test Register -- Index 50h (Bank 6) FAN 1 Pre-Scale Register--Index00h(Bank 0) Power on default [7:0] = 0000-0001 b READ/WRIT BIT NAME DESCRIPTION E 7 PWM_CLK_SEL1 Read/Write PWM Input Clock Select. This bit select Fan 1 input clock to pre-scale divider. 0: 24 MHz 1: 180 KHz 6-0 PRE_SCALE1[6:0] Read/Write Fan 1 Input Clock Pre-Scale. The divider of input clock is the number defined by pre-scale. Thus, writing 1 transfers the input clock directly to counter. The maximum divider is 128 (7Fh). 01h : divider is 1 02h : divider is 2 03h : divider is 3 : : PWM frequency = (Input Clock / Pre-scale) / 256 Publication Release Date: May 30, 2005 - 55 - Revision A1 W83697HF/ HG FAN 1 Duty Cycle Select Register-- 01h (Bank 0) Power on default [7:0] 1111,1111 b BIT NAME READ/WRITE DESCRIPTION 7-0 F1_DC[7:0] Read/Write FanPWM1 Duty Cycle. This 8-bit register determines the number of input clock cycles, out of 256-cycle period, during which the PWM output is high. During smart fan 1 control mode, read this register will return smart fan duty cycle. 00h: PWM output is always logical Low. FFh: PWM output is always logical High. XXh: PWM output logical High percentage is (XX/256*100%) during one cycle. FAN 2 Pre-Scale Register-- Index 02h Power on default [7:0] = 0000,0001 b READ/WRIT BIT NAME DESCRIPTION E PWM 2 Input Clock Select. This bit select Fan 2 input clock to pre-scale divider. 7 PWM_CLK_SEL2 Read/Write 0: 1 MHz 1: 125 KHz Fan 2 Input Clock Pre-Scale. The divider of input clock is the number defined by pre-scale. Thus, writing 0 transfers the input clock directly to counter. The maximum divider is 128 (7Fh). 01h : divider is 1 6-0 PRE_SCALE2[6:0] Read/Write 02h : divider is 2 03h : divider is 3 : : PWM frequency = (Input Clock / Pre-scale) / 256 - 56 - W83697HF/ HG FAN2 Duty Cycle Select Register-- Index 03h Power on default [7:0] = 1111,1111 b BIT NAME READ/WRITE DESCRIPTION 7-0 F2_DC[7:0] Read/Write FanPWM2 Duty Cycle. This 8-bit register determines the number of input clock cycles, out of 256-cycle period, during which the PWM output is high. During smart fan 2 control mode, read this register will return smart fan duty cycle. 00h: PWM output is always logical Low. FFh: PWM output is always logical High. XXh: PWM output logical High percentage is XX/256*100% during one cycle. FAN Configuration Register-- Index 04h Power on default [7:0] = 0000,0000 b BIT NAME READ/WRITE DESCRIPTION 7-2 Reserved Read/Write Reserved 5-4 FAN2_MODE Read/Write FAN 2 PWM Control Mode. 00 - Manual PWM Control Mode. (Default) 01 - Thermal Cruise mode. 10 - Fan Speed Cruise Mode. 11 - Reserved. 3-2 FAN1_MODE Read/Write FAN 1 PWM Control Mode. 00 - Manual PWM Control Mode. (Default) 01 - Thermal Cruise mode. 10 - Fan Speed Cruise Mode. 11 - Reserved. 1 FAN2_OB Read/Write Enable Fan 2 as Output Buffer. Set to 0, FANPWM2 can drive logical high or logical low. Set to 1, FANPWM2 is open-drain 0 FAN1_OB Read/Write Enable Fan 1 as Output Buffer. Set to 1, FANPWM1 can drive logical high or logical low. Set to 1, FANPWM1 is open-drain Publication Release Date: May 30, 2005 - 57 - Revision A1 W83697HF/ HG VTIN1 Target Temperature Register/ Fan 1 Target Speed Register -- Index 05h Power on default [7:0] = 0000,0000 b CPUT1 target temperature register for Thermal Cruise mode. BIT NAME READ/WRITE DESCRIPTION 7 Reserved Read/Write Reserved. VTIN1 Target Temperature. Only for Thermal 6-0 TEMP_TAR_T1[6:0] Read/Write Cruise Mode while CR84h bit3-2 is 01. Fan 1 target speed register for Fan Speed Cruise mode. BIT NAME READ/WRITE DESCRIPTION SPD_TAR_FAN1[7 Fan 1 Target Speed Control. Only for Fan Speed 7-0 Read/Write :0] Cruise Mode while CR84h bit3-2 is 10. VTIN2 Target Temperature Register/ Fan 2 Target Speed Register -- Index 06h Power on - [7:0] = 0000,0000 b CPUT2 target temperature register for Thermal Cruise mode. BIT NAME READ/WRITE DESCRIPTION 7 Reserved Read/Write Reserved. TEMP_TAR_T2[6: VTIN2 Target Temperature. Only for Thermal 6-0 Read/Write 0] Cruise Mode while CR84h bit5-4 is 01. Fan 2 target speed register for Fan Speed Cruise mode. BIT NAME READ/WRITE DESCRIPTION SPD_TAR_FAN2[7 Fan 2 Target Speed Control. Only for Fan Speed 7-0 Read/Write :0] Cruise Mode while CR84h bit5-4 is 10. - 58 - W83697HF/ HG Tolerance of Target Temperature or Target Speed Register -- Index 07h Power on default [7:0] = 0001,0001 b Tolerance of CPUT1/CPUT2 target temperature register. BIT NAME READ/WRITE DESCRIPTION Tolerance of VTIN2 Target Temperature. Only for 7-4 TOL_T2[3:0] Read/Write Thermal Cruise mode. Tolerance of VTIN1 Target Temperature. Only for 3-0 TOL_T1[3:0] Read/Write Thermal Cruise mode. Tolerance of Fan 1/2 target speed register. BIT NAME READ/WRITE DESCRIPTION Tolerance of Fan 2 Target Speed Count. Only for 7-4 TOL_FS2[3:0] Read/Write Fan Speed Cruise mode. Tolerance of Fan 1 Target Speed Count. Only for 3-0 TOL_FS1[3:0] Read/Write Fan Speed Cruise mode. Fan 1 PWM Stop Duty Cycle Register -- Index 08h Power on default [7:0] = 0000,0001 b BIT NAME READ/WRITE DESCRIPTION In Thermal Cruise mode, PWM duty will be 0 if it 7-0 STOP_DC1[7:0] Read/Write decreases to under this value. This register should be written a non-zero minimum PWM stop duty cycle. Fan 2 PWM Stop Duty Cycle Register -- 09h (Bank 0) Power on default [7:0] = 0000,0001 b READ/WRIT BIT NAME DESCRIPTION E In Thermal Cruise mode, PWM duty will be 0 if it decreases to under this register value. This register 7-0 STOP_DC2[7:0] Read/Write should be written a non-zero minimum PWM stop duty cycle. Publication Release Date: May 30, 2005 - 59 - Revision A1 W83697HF/ HG Fan 1 Start-up Duty Cycle Register -- Index 0Ah Power on default [7:0] = 0000,0001 b BIT NAME READ/WRITE DESCRIPTION In Thermal Cruise mode, PWM duty will increase from 0 to this register value to provide a minimum 7-0 START_DC1[7:0] Read/Write duty cycle to turn on the fan. This register should be written a fan start-up duty cycle. Fan 2 Start-up Duty Cycle Register -- Index 0Bh Power on default [7:0] = 0000,0001 b BIT NAME READ/WRITE DESCRIPTION In Thermal Cruise mode, PWM duty will increase from 0 to this register value to provide a minimum 7-0 START_DC2[7:0] Read/Write duty cycle to turn on the fan. This register should be written a fan start-up duty cycle. Fan 1 Stop Time Register -- Index 0Ch Power on default [7:0] = 0011,1100 b BIT NAME READ/WRITE DESCRIPTION In Thermal Cruise mode, this register determines the time of which PWM duty is from stop duty cycle to 0 7-0 STOP_TIME1[7:0] Read/Write duty cycle. The unit of this register is 0.1 second. The default value is 6 seconds. Fan 2 Stop Time Register -- Index 0Dh Power on default [7:0] = 0011,1100 b BIT NAME READ/WRITE DESCRIPTION In Thermal Cruise mode, this register determines the time of which PWM duty is from stop duty cycle to 0 7-0 STOP_TIME2[7:0] Read/Write duty cycle. The unit of this register is 0.1 second. The default value is 6 seconds. - 60 - W83697HF/ HG Fan Step Down Time Register -- Index 0Eh Power on defualt [7:0] = 0000,1010 b BIT NAME READ/WRITE DESCRIPTION The time interval, which is 0.1 second unit, to 7-0 STEP_UP_T[7:0] Read/Write decrease PWM duty in Smart Fan Control mode. Fan Step Up Time Register -- Index 0Fh Power on default [7:0] = 0000,1010 b BIT NAME READ/WRITE DESCRIPTION The time interval, which is 0.1 second unit, to 7-0 STEP_DOWN_T[7:0] Read/Write increase PWM duty in Smart Fan Control mode. Publication Release Date: May 30, 2005 - 61 - Revision A1 W83697HF/ HG 7. CONFIGURATION REGISTER 7.1 Plug and Play Configuration The W83697HF uses Compatible PNP protocol to access configuration registers for setting up different types of configurations. In W83697HF, there are eleven Logical Devices (from Logical Device 0 to Logical Device B with the exception of logical device 4 for backward compatibility) which correspond to eleven individual functions: FDC (logical device 0), PRT (logical device 1), UART1 (logical device 2), UART2 (logical device 3), CIR (Consumer IR, logical device 6), GPIO1 (logical device 7), GPIO5(logical device 8),GPIO2 ~GPIO4(logical device 9), ACPI ((logical device A), and Hardware monitor (logical device B). Each Logical Device has its own configuration registers (above CR30). Host can access those registers by writing an appropriate logical device number into logical device select register at CR7. 7.2 Compatible PnP 7.2.1 Extended Function Registers In Compatible PnP, there are two ways to enter Extended Function and read or write the configuration registers. HEFRAS (CR26 bit 6) can be used to select one out of these two methods of entering the Extended Function mode as follows: HEFRAS ADDRESS AND VALUE 0 write 87h to the location 2Eh twice 1 write 87h to the location 4Eh twice After Power-on reset, the value on RTSA# (pin 49) is latched by HEFRAS of CR26. In Compatible PnP, a specific value (87h) must be written twice to the Extended Functions Enable Register (I/O port address 2Eh or 4Eh). Secondly, an index value (02h, 07h-FFh) must be written to the Extended Functions Index Register (I/O port address 2Eh or 4Eh same as Extended Functions Enable Register) to identify which configuration register is to be accessed. The designer can then access the desired configuration register through the Extended Functions Data Register (I/O port address 2Fh or 4Fh). After programming of the configuration register is finished, an additional value (AAh) should be written to EFERs to exit the Extended Function mode to prevent unintentional access to those configuration - 62 - W83697HF/ HG registers. The designer can also set bit 5 of CR26 (LOCKREG) to high to protect the configuration registers against accidental accesses. The configuration registers can be reset to their default or hardware settings only by a cold reset (pin MR = 1). A warm reset will not affect the configuration registers. 7.2.2 Extended Functions Enable Registers (EFERs) After a power-on reset, the W83697HF enters the default operating mode. Before the W83697HF enters the extended function mode, a specific value must be programmed into the Extended Function Enable Register (EFER) so that the extended function register can be accessed. The Extended Function Enable Registers are write-only registers. On a PC/AT system, their port addresses are 2Eh or 4Eh (as described in previous section). 7.2.3 Extended Function Index Registers (EFIRs), Extended Function Data Registers(EFDRs) After the extended function mode is entered, the Extended Function Index Register (EFIR) must be loaded with an index value (02h, 07h-FEh) to access Configuration Register 0 (CR0), Configuration Register 7 (CR07) to Configuration Register FE (CRFE), and so forth through the Extended Function Data Register (EFDR). The EFIRs are write-only registers with port address 2Eh or 4Eh on PC/AT systems; the EFDRs are read/write registers with port address 2Fh or 4Fh on PC/AT systems. 7.3 Configuration Sequence To program W83697HF configuration registers, the following configuration sequence must be followed: (1). Enter the extended function mode (2). Configure the configuration registers (3). Exit the extended function mode 7.3.1 Enter the extended function mode To place the chip into the extended function mode, two successive wrtites of 0x87 must be applied to Extended Function Enable Registers(EFERs, i.e. 2Eh or 4Eh). 7.3.2 Configurate the configuration registers The chip selects the logical device and activates the desired logical devices through Extended Function Index Register(EFIR) and Extended Function Data Register(EFDR). EFIR is located at the same address as EFER, and EFDR is located at address (EFIR+1). First, write the Logical Device Number (i.e.,0x07) to the EFIR and then write the number of the desired logical device to the EFDR. If accessing the Chip(Global) Control Registers, this step is not required. Secondly, write the address of the desired configuration register within the logical device to the EFIR and then write (or read) the desired configuration register through EFDR. 7.3.3 Exit the extended function mode To exit the extended function mode, one write of 0xAA to EFER is required. Once the chip exits the extended function mode, it is in the normal running mode and is ready to enter the configuration mode. Publication Release Date: May 30, 2005 - 63 - Revision A1 W83697HF/ HG 7.3.4 Software programming example The following example is written in Intel 8086 assembly language. It assumes that the EFER is located at 2Eh, so EFIR is located at 2Eh and EFDR is located at 2Fh. If HEFRAS (CR26 bit 6) is set, 4Eh can be directly replaced by 4Eh and 2Fh replaced by 4Fh. ;----------------------------------------------------------------------------------- ; Enter the extended function mode ,interruptible double-write | ;----------------------------------------------------------------------------------- MOV DX,2EH MOV AL,87H OUT DX,AL OUT DX,AL ;----------------------------------------------------------------------------- ; Configurate logical device 1, configuration register CRF0 | ;----------------------------------------------------------------------------- MOV DX,2EH MOV AL,07H OUT DX,AL ; point to Logical Device Number Reg. MOV DX,2FH MOV AL,01H OUT DX,AL ; select logical device 1 ; MOV DX,2EH MOV AL,F0H OUT DX,AL ; select CRF0 MOV DX,2FH MOV AL,3CH OUT DX,AL ; update CRF0 with value 3CH ;------------------------------------------ ; Exit extended function mode | ;------------------------------------------ MOV DX,2EH MOV AL,AAH OUT DX,AL - 64 - W83697HF/ HG 7.4 Chip (Global) Control Register CR02 (Default 0x00, Write Only) Bit 7 - 1: Reserved. Bit 0: SWRST --> Soft Reset. CR07 Bit 7 - 0: LDNB7 - LDNB0 --> Logical Device Number Bit 7 - 0 CR20 Bit 7 - 0: DEVIDB7 - DEBIDB0 --> Device ID Bit 7 - Bit 0 = 0x 60 (read only). CR21 Bit 7 - 0: DEVREVB7 - DEBREVB0 --> Device Rev = 0x1X (read only). X : Version change number (Bit 3~0). CR22 (Default 0xff) Bit 7~ 5: Reserved. Bit 4: HMPWD = 0 Power down = 1 No Power down Bit 3: URBPWD = 0 Power down = 1 No Power down Bit 2: URAPWD = 0 Power down = 1 No Power down Bit 1: PRTPWD = 0 Power down = 1 No Power down Bit 0: FDCPWD = 0 Power down = 1 No Power down Publication Release Date: May 30, 2005 - 65 - Revision A1 W83697HF/ HG CR23 (Default 0x00) Bit 7 ~ 1: Reserved. Bit 0: IPD (Immediate Power Down). When set to 1, it will put the whole chip into power down mode immediately. CR24 (Default 0x00) Bit 7 : Reserved. Bit 6: CLKSEL(Enable 48Mhz) = 0 The clock input on Pin 1 should be 24 Mhz. = 1 The clock input on Pin 1 should be 48 Mhz. The corresponding power-on setting pin is SOUTB (pin 61). Bit[5:4]: ROM size select =00 1M =01 2M =10 4M =11 Reserved Bit3:MEMW# Select (PIN97) = 0 MEMW# Disable = 1 MEMW# Enable Bit2:Reserved Bit1 : Enable Flash ROM Interface = 0 Flash ROM Interface is enabled after hardware reset = 1 Flash ROM Interface is disabled after hardware reset This bit is read only, and set/reset by power-on setting pin. The corresponding power-on setting pin is PENROM#(pin 52) Bit 0: PNPCSV# = 0 The Compatible PnP address select registers have default values. = 1 The Compatible PnP address select registers have no default value. The corresponding power-on setting pin is DTRA# (pin 50). CR25 (Default 0x00) Bit 7 ~ 4: Reserved Bit 3: URBTRI Bit 2: URATRI Bit 1: PRTTRI Bit 0: FDCTRI. - 66 - W83697HF/ HG CR26 (Default 0x00) Bit 7: SEL4FDD = 0 Select two FDD mode. = 1 Select four FDD mode. Bit 6: HEFRAS These two bits define how to enable Configuration mode. The corresponding power-on setting pin is RTSA #(pin 49). HEFRAS Address and Value = 0 Write 87h to the location 2E twice. = 1 Write 87h to the location 4E twice. Bit 5: LOCKREG = 0 Enable R/W Configuration Registers. = 1 Disable R/W Configuration Registers. Bit4: Reserved Bit 3: DSFDLGRQ = 0 Enable FDC legacy mode on IRQ and DRQ selection, then DO register bit 3 is effective on selecting IRQ = 1 Disable FDC legacy mode on IRQ and DRQ selection, then DO register bit 3 is not effective on selecting IRQ Bit 2: DSPRLGRQ = 0 Enable PRT legacy mode on IRQ and DRQ selection, then DCR bit 4 is effective on selecting IRQ = 1 Disable PRT legacy mode on IRQ and DRQ selection, then DCR bit 4 is not effective on selecting IRQ Bit 1: DSUALGRQ = 0Enable UART A legacy mode IRQ selecting, then MCR bit 3 is effective on selecting IRQ = 1Disable UART A legacy mode IRQ selecting, then MCR bit 3 is not effective on selecting IRQ Bit 0: DSUBLGRQ = 0 Enable UART B legacy mode IRQ selecting, then MCR bit 3 is effective on selecting IRQ = 1 Disable UART B legacy mode IRQ selecting, then MCR bit 3 is not effective on selecting IRQ Publication Release Date: May 30, 2005 - 67 - Revision A1 W83697HF/ HG CR28 (Default 0x00) Bit 7 - 3: Reserved. Bit 2 - 0: PRTMODS2 - PRTMODS0 = 0xx Parallel Port Mode = 100 Reserved = 101 External FDC Mode = 110 Reserved = 111 External two FDC Mode CR29 (GPIO1,5(50~51) & Game port & MIDI port Select default 0x00 ) Bit 7 : Port Select (select Game Port or General Purpose I/O Port 1) = 0 Game Port = 1 General Purpose I/O Port 1 (pin121~128 select function GP10~GP17) Bit [6:5] : (Pin119) 00 MSI 01 WDTO# 10 Reserved 11 GP51 Bit[4:3] : (Pin 120) 00 MSO 01 PLED 10 Reserved 11 GP50 Bit 2 :(Pin117) OVT# & SMI Select(Pin117) = 0 OVT# = 1 SMI# Bit 1~0 : Reserved - 68 - W83697HF/ HG CR2A(GPIO2 ~ 5& Flash ROM Interface Select Default 0xFF if PENROM# = 0 during POR, default 0x00 otherwise) Bit 7 : (PIN 86 ~89 & 91 ~94) = 0 GPIO 2 = 1 Flash IF (xD7 ~ XD0) Bit 6 : (PIN 78 ~ 85) = 0 GPIO 3 = 1 Flash IF (XA7 ~ XA0) Bit 5 : (PIN 69 ~ 74 & 76 ~77) = 0 GPIO 4 = 1 Flash IF (XA!5 ~ XA10 & XA7 ~ A0) Bit 4: (PIN 66 ~ 68 & 95 ~ 97) = 0 GPIO 5(GP52 ~ 57) = 1 Flash IF(XA18 ~ XA16 , ROMCS#, MEMR #, MEMW#) Bit 0~3 : Reserved Publication Release Date: May 30, 2005 - 69 - Revision A1 W83697HF/ HG 7.5 Logical Device 0 (FDC) CR30 (Default 0x01 if PNPCSV = 0 during POR, default 0x00 otherwise) Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive. CR60, CR 61 (Default 0x03, 0xf0 if PNPCSV = 0 during POR, default 0x00, 0x00 otherwise) These two registers select FDC I/O base address [0x100:0xFF8] on 8 byte boundary. CR70 (Default 0x06 if PNPCSV = 0 during POR, default 0x00 otherwise) Bit 7 - 4: Reserved. Bit 3 - 0: These bits select IRQ resource for FDC. CR74 (Default 0x02 if PNPCSV = 0 during POR, default 0x04 otherwise) Bit 7 - 3: Reserved. Bit 2 - 0: These bits select DRQ resource for FDC. = 0x00 DMA0 = 0x01 DMA1 = 0x02 DMA2 = 0x03 DMA3 = 0x04 - 0x07 No DMA active CRF0 (Default 0x0E) FDD Mode Register Bit 7: FIPURDWN This bit controls the internal pull-up resistors of the FDC input pins RDATA, INDEX, TRAK0, DSKCHG, and WP. = 0 The internal pull-up resistors of FDC are turned on.(Default) = 1 The internal pull-up resistors of FDC are turned off. Bit 6: INTVERTZ This bit determines the polarity of all FDD interface signals. = 0 FDD interface signals are active low. = 1 FDD interface signals are active high. Bit 5: DRV2EN (PS2 mode only) When this bit is a logic 0, indicates a second drive is installed and is reflected in status register A. - 70 - W83697HF/ HG Bit 4: Swap Drive 0, 1 Mode = 0 No Swap (Default) = 1 Drive and Motor select 0 and 1 are swapped. Bit 3 - 2 Interface Mode = 11 AT Mode (Default) = 10 (Reserved) = 01 PS/2 = 00 Model 30 Bit 1: FDC DMA Mode = 0 Burst Mode is enabled = 1 Non-Burst Mode (Default) Bit 0: Floppy Mode = 0 Normal Floppy Mode (Default) = 1 Enhanced 3-mode FDD CRF1 (Default 0x00) Bit 7 - 6: Boot Floppy = 00 FDD A = 01 FDD B = 10 FDD C = 11 FDD D Bit 5, 4: Media ID1, Media ID0. These bits will be reflected on FDC's Tape Drive Register bit 7, 6. Bit 3 - 2: Density Select = 00 Normal (Default) = 01 Normal = 10 1 ( Forced to logic 1) = 11 0 ( Forced to logic 0) Bit 1: DISFDDWR = 0 Enable FDD write. = 1 Disable FDD write(forces pins WE, WD stay high). Bit 0: SWWP = 0 Normal, use WP to determine whether the FDD is write protected or not. = 1 FDD is always write-protected. Publication Release Date: May 30, 2005 - 71 - Revision A1 W83697HF/ HG CRF2 (Default 0xFF) Bit 7 - 6: FDD D Drive Type Bit 5 - 4: FDD C Drive Type Bit 3 - 2: FDD B Drive Type Bit 1 - 0: FDD A Drive Type CRF4 (Default 0x00) FDD0 Selection: Bit 7: Reserved. Bit 6: Precomp. Disable. = 1 Disable FDC Precompensation. = 0 Enable FDC Precompensation. Bit 5: Reserved. Bit 4 - 3: DRTS1, DRTS0: Data Rate Table select (Refer to TABLE A). = 00 Select Regular drives and 2.88 format = 01 3-mode drive = 10 2 Meg Tape = 11 Reserved Bit 2: Reserved. Bit 1:0: DTYPE0, DTYPE1: Drive Type select (Refer to TABLE B). CRF5 (Default 0x00) FDD1 Selection: Same as FDD0 of CRF4. TABLE A DRIVE RATE TABLE DATA RATE SELECTED DATA RATE SELDEN SELECT DRTS1 DRTS0 DRATE1 DRATE0 MFM FM 1 1 1Meg --- 1 0 0 0 0 500K 250K 1 0 1 300K 150K 0 1 0 250K 125K 0 1 1 1Meg --- 1 0 1 0 0 500K 250K 1 0 1 500K 250K 0 1 0 250K 125K 0 1 1 1Meg --- 1 1 0 0 0 500K 250K 1 0 1 2Meg --- 0 1 0 250K 125K 0 - 72 - W83697HF/ HG TABLE B DTYPE0 DTYPE1 DRVDEN0(PIN 2) DRVDEN1(PIN 3) DRIVE TYPE 4/2/1 MB 3.5”“ 0 0 SELDEN DRATE0 2/1 MB 5.25” 2/1.6/1 MB 3.5” (3-MODE) 0 1 DRATE1 DRATE0 1 0 DRATE0 SELDEN 1 1 DRATE0 DRATE1 7.6 Logical Device 1 (Parallel Port) CR30 (Default 0x01 if PNPCSV = 0 during POR, default 0x00 otherwise) Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive. CR60, CR 61 (Default 0x03, 0x78 if PNPCSV = 0 during POR, default 0x00, 0x00 otherwise) These two registers select Parallel Port I/O base address. [0x100:0xFFC] on 4 byte boundary (EPP not supported) or [0x100:0xFF8] on 8 byte boundary (all modes supported, EPP is only available when the base address is on 8 byte boundary). CR70 (Default 0x07 if PNPCSV = 0 during POR, default 0x00 otherwise) Bit 7 - 4: Reserved. Bit [3:0]: These bits select IRQ resource for Parallel Port. CR74 (Default 0x04) Bit 7 - 3: Reserved. Bit 2 - 0: These bits select DRQ resource for Parallel Port. 0x00=DMA0 0x01=DMA1 0x02=DMA2 0x03=DMA3 0x04 - 0x07= No DMA active Publication Release Date: May 30, 2005 - 73 - Revision A1 W83697HF/ HG CRF0 (Default 0x3F) Bit 7: Reserved. Bit 6 - 3: ECP FIFO Threshold. Bit 2 - 0: Parallel Port Mode (CR28 PRTMODS2 = 0) = 100 Printer Mode (Default) = 000 Standard and Bi-direction (SPP) mode = 001 EPP - 1.9 and SPP mode = 101 EPP - 1.7 and SPP mode = 010 ECP mode = 011 ECP and EPP - 1.9 mode = 111 ECP and EPP - 1.7 mode. 7.7 Logical Device 2 (UART A) CR30 (Default 0x01 if PNPCSV = 0 during POR, default 0x00 otherwise) Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive. CR60, CR 61 (Default 0x03, 0xF8 if PNPCSV = 0 during POR, default 0x00, 0x00 otherwise) These two registers select Serial Port 1 I/O base address [0x100:0xFF8] on 8 byte boundary. CR70 (Default 0x04 if PNPCSV = 0 during POR, default 0x00 otherwise) Bit 7 - 4: Reserved. Bit 3 - 0: These bits select IRQ resource for Serial Port 1. CRF0 (Default 0x00) Bit 7 - 2: Reserved. Bit 1 - 0: SUACLKB1, SUACLKB0 = 00 UART A clock source is 1.8462 Mhz (24MHz/13) = 01 UART A clock source is 2 Mhz (24MHz/12) = 10 UART A clock source is 24 Mhz (24MHz/1) = 11 UART A clock source is 14.769 Mhz (24mhz/1.625) - 74 - W83697HF/ HG 7.8 Logical Device 3 (UART B) CR30 (Default 0x01 if PNPCSV = 0 during POR, default 0x00 otherwise) Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive. CR60, CR 61 (Default 0x02, 0xF8 if PNPCSV = 0 during POR, default 0x00, 0x00 otherwise) These two registers select Serial Port 2 I/O base address [0x100:0xFF8] on 8 byte boundary. CR70 (Default 0x03 if PNPCSV = 0 during POR, default 0x00 otherwise) Bit 7 - 4: Reserved. Bit [3:0]: These bits select IRQ resource for Serial Port 2. CRF0 (Default 0x00) Bit 7 - 4: Reserved. Bit 3: RXW4C = 0 No reception delay when SIR is changed from TX mode to RX mode. = 1 Reception delays 4 characters-time (40 bit-time) when SIR is changed from TX mode to RX mode. Bit 2: TXW4C = 0 No transmission delay when SIR is changed from RX mode to TX mode. = 1 Transmission delays 4 characters-time (40 bit-time) when SIR is changed from RX mode to TX mode. Bit 1 - 0: SUBCLKB1, SUBCLKB0 = 00 UART B clock source is 1.8462 Mhz (24MHz/13) = 01 UART B clock source is 2 Mhz (24MHz/12) = 10 UART B clock source is 24 Mhz (24MHz/1) = 11 UART B clock source is 14.769 Mhz (24mhz/1.625) CRF1 (Default 0x00) Bit 7: Reserved. Bit 6: IRLOCSEL. IR I/O pins' location select. = 0 Through SINB/SOUTB. = 1 Through IRRX/IRTX. Bit 5: IRMODE2. IR function mode selection bit 2. Bit 4: IRMODE1. IR function mode selection bit 1. Bit 3: IRMODE0. IR function mode selection bit 0. Publication Release Date: May 30, 2005 - 75 - Revision A1 W83697HF/ HG IR MODE IR FUNCTION IRTX IRRX 00X Disable tri-state high 010* IrDA Active pulse 1.6 µS Demodulation into SINB/IRRX 011* IrDA Active pulse 3/16 bit time Demodulation into SINB/IRRX 100 ASK-IR Inverting IRTX/SOUTB pin routed to SINB/IRRX 101 ASK-IR Inverting IRTX/SOUTB & 500 routed to SINB/IRRX KHZ clock 110 ASK-IR Inverting IRTX/SOUTB Demodulation into SINB/IRRX 111* ASK-IR Inverting IRTX/SOUTB & 500 Demodulation into SINB/IRRX KHZ clock Note: The notation is normal mode in the IR function. Bit 2: HDUPLX. IR half/full duplex function select. = 0 The IR function is Full Duplex. = 1 The IR function is Half Duplex. Bit 1: TX2INV. = 0 the SOUTB pin of UART B function or IRTX pin of IR function in normal condition. = 1 inverse the SOUTB pin of UART B function or IRTX pin of IR function. Bit 0: RX2INV. = 0 the SINB pin of UART B function or IRRX pin of IR function in normal condition. = 1 inverse the SINB pin of UART B function or IRRX pin of IR function 7.9 Logical Device 6 (CIR) CR30 (Default 0x00) Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive. CR60, CR 61 (Default 0x00, 0x00) These two registers select CIR I/O base address [0x100:0xFF8] on 8 byte boundary. CR70 (Default 0x00) Bit 7 - 4: Reserved. Bit [3:0]: These bits select IRQ resource for CIR. - 76 - W83697HF/ HG 7.10 Logical Device 7 (Game Port GPIO Port 1) CR30 (Default 0x00) Bit 7 - 1: Reserved. Bit 0: = 1 Activate Game Port./GP1 = 0 Game Port/GP1 is inactive. CR60, CR 61 (Default 0x02, 0x01 if PNPCSV = 0 during POR, default 0x00 otherwise) These two registers select the Game Port base address [0x100:0xFFF] on 8 byte boundary. CR62, CR 63 (Default 0x00, 0x00) These two registers select the GPIO1 base address [0x100:0xFFF] on 1 byte boundary IO address : CRF1 base address CRF0 (GP10-GP17 I/O selection register. Default 0xFF) When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port. CRF1 (GP10-GP17 data register. Default 0x00) If a port is programmed to be an output port, then its respective bit can be read/written If a port is programmed to be an input port, then its respective bit can only be read. CRF2 (GP10-GP17 inversion register. Default 0x00) When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register. Publication Release Date: May 30, 2005 - 77 - Revision A1 W83697HF/ HG 7.11 Logical Device 8 (MIDI Port and GPIO Port 5) CR30 (MIDI Port Default 0x00) Bit 7 - 1: Reserved. Bit 0: = 1 MIDI/GP5 port is Activate = 0 MIDI/GP5 port is inactive. CR60, CR 61 (Default 0x03, 0x30 if PNPCSV = 0 during POR, default 0x00 otherwise) These two registers select the MIDI Port base address [0x100:0xFFF] on 2byte boundary. CR62, CR 63 (Default 0x00, 0x00 ) These two registers select the GPIO5 base address [0x100:0xFFF] on 4byte boundary. IO address : CRF1 base address IO address + 1 : CRF3 base address IO address + 2 : CRF4 base address IO address + 3 : CRF5 base address CR70 (Default 0x09 if PNPCSV = 0 during POR, default 0x00 otherwise) Bit 7 - 4: Reserved. Bit [3:0]: These bits select IRQ resource for MIDI Port . CRF0 (GP5 selection register. Default 0xFF) When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port. CRF1 (GP5 data register. Default 0x00) If a port is programmed to be an output port, then its respective bit can be read/written. If a port is programmed to be an input port, then its respective bit can only be read. CRF2 (GP5 inversion register. Default 0x00) When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register. - 78 - W83697HF/ HG CRF3 (PLED mode register. Default 0x00) Bit 7 ~ 3 : Reserved . Bit 2: select WDTO# count mode. = 0 second = 1 minute Bit 1 ~ 0: select PLED mode = 00 Power LED pin is tri-stated. = 01 Power LED pin is droved low. = 10 Power LED pin is a 1Hz toggle pulse with 50 duty cycle. = 11 Power LED pin is a 1/4Hz toggle pulse with 50 duty cycle. CRF4 (Default 0x00) Watch Dog Timer Time-out value. Writing a non-zero value to this register causes the counter to load the value to Watch Dog Counter and start counting down. Reading this register returns current value in Watch Dog Counter instead of Watch Dog Timer Time-out value. Bit 7 - 0: = 0x00 Time-out Disable = 0x01 Time-out occurs after 1 second/minute = 0x02 Time-out occurs after 2 second/minutes = 0x03 Time-out occurs after 3 second/minutes ................................................ = 0xFF Time-out occurs after 255 second/minutes CRF5 (Default 0x00) Bit 7 ~ 6 : Reserved . Bit 5: Force Watch Dog Timer Time-out, Write only* = 1 Force Watch Dog Timer time-out event; this bit is self-clearing. Bit 4: Watch Dog Timer Status, R/W = 1 Watch Dog Timer time-out occurred. = 0 Watch Dog Timer counting Bit 3 -0: These bits select IRQ resource for Watch Dog. Setting of 2 selects SMI. Publication Release Date: May 30, 2005 - 79 - Revision A1 W83697HF/ HG 7.12 Logical Device 9 (GPIO Port 2 ~ GPIO Port 4 ) CR30 (Default 0x00) Bit 7 ~ 3: Reserved. Bit 2: = 1 Activate GPIO4. = 0 GPIO4 is inactive Bit 1: = 1 Activate GPIO3. = 0 GPIO3 is inactive Bit 0: = 1 Activate GPIO2. = 0 GPIO2 is inactive. CR60,61(Default 0x00,0x00). These two registers select the GP2,3,4 base address(0x100:FFE) ON 3 bytes boundary. IO address: : CRF1 base address IO address + 1 : CRF3 base address IO address + 2 : CRF7 base address CRF0 (GP2 I/O selection register. Default 0xFF ) When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port. CRF1 (GP2 data register. Default 0x00 ) If a port is programmed to be an output port, then its respective bit can be read/written. If a port is programmed to be an input port, then its respective bit can only be read. CRF2 (GP2 inversion register. Default 0x00 ) When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register. CRF3 (GP3 I/O selection register. Default 0xFF ) When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port. CRF4 (GP3 data register. Default 0x00 ) If a port is programmed to be an output port, then its respective bit can be read/written. If a port is programmed to be an input port, then its respective bit can only be read. CRF5 (GP3 inversion register. Default 0x00 ) When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register. CRF6 (GP4 I/O selection register. Default 0xFF ) When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port. - 80 - W83697HF/ HG CRF7 (GP4 data register. Default 0x00 ) If a port is programmed to be an output port, then its respective bit can be read/written. If a port is programmed to be an input port, then its respective bit can only be read. CRF8 (GP5 inversion register. Default 0x00 ) When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register. Publication Release Date: May 30, 2005 - 81 - Revision A1 W83697HF/ HG 7.13 Logical Device A (ACPI) CR30 (Default 0x00) Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive. CR70 (Default 0x00) Bit 7 - 4: Reserved. PME Bit 3 - 0: These bits select IRQ resources for SMI / CRE0 (Default 0x00) Bit7 : ENCIRWAKEUP. Enable CIR to wake-up system . = 0 Disable CIR wake up function = 1 Enable CIR wake up function Bit 5 : CIR_STS. This bit is cleared by reading 1 this register. = 0 Disable = 1 Enable Bit6, 4 ~ 0 : Reserved CRE 1 (Default 0x00) CIR wake up index register The range of CIR wake up index register is 0x20 ~ 0x2F . CRE 2 CIR wake up data register This register holds the value of wake up key register indicated by CRE1. This register can be read/written. CRE5 (Default 0x00) Bit 7 : Reserved Bit 6 ~ 0 :Compared Code Length . When the compared codes are storage in the data register, these data length should be written to this register. CRE6 (Default 0x00) Bit 7 - 6: Reserved. Bit 5 - 0: CIR Baud Rate Divisor. The clock base of CIR is 32khz, so that the baud rate is 32khz divided by ( CIR Baud Rate Divisor + 1). - 82 - W83697HF/ HG CRE7 (Default 0x00) Bit 7 - 3: Reserved. Bit 2:Reset CIR Power-On function. After using CIR power-on, the software should write logical 1 to restart CIR power-on function. Bit 1: Invert RX Data. = 1 Inverting RX Data. = 0 Not inverting RX Data. Bit 0: Enable Demodulation. = 1 Enable received signal to demodulate. = 0 Disable received signal to demodulate. CRF0 (Default 0x00) Bit 7: CHIPPME. Chip level auto power management enable. = 0 disable the auto power management functions = 1 enable the auto power management functions. Bit 6: CIRPME. Consumer IR port auto power management enable. = 0 disable the auto power management functions = 1 enable the auto power management functions. Bit 5: MIDIPME. MIDI port auto power management enable. = 0 disable the auto power management functions = 1 enable the auto power management functions. Bit 4: Reserved. Return zero when read. Bit 3: PRTPME. Printer port auto power management enable. = 0 disable the auto power management functions. = 1 enable the auto power management functions. Bit 2: FDCPME. FDC auto power management enable. = 0 disable the auto power management functions. = 1 enable the auto power management functions. Bit 1: URAPME. UART A auto power management enable. = 0 disable the auto power management functions. = 1 enable the auto power management functions. Bit 0: URBPME. UART B auto power management enable. = 0 disable the auto power management functions. = 1 enable the auto power management functions. Publication Release Date: May 30, 2005 - 83 - Revision A1 W83697HF/ HG CRF1 (Default 0x00) Bit 7: WAK_STS. This bit is set when the chip is in the sleeping state and an enabled resume event occurs. Upon setting this bit, the sleeping/working state machine will transition the system to the working state. This bit is only set by hardware and is cleared by writing a 1 to this bit position or by the sleeping/working state machine automatically when the global standby timer expires. = 0 the chip is in the sleeping state. = 1 the chip is in the working state. Bit 6 - 5: Devices' trap status. Bit 4: Reserved. Return zero when read. Bit 3 - 0: Devices' trap status. CRF3 (Default 0x00) Bit 7 ~ 4: Reserved. Return zero when read. Bit 3 ~ 0: Device's IRQ status. These bits indicate the IRQ status of the individual device respectively. The device's IRQ status bit is set by their source device and is cleared by writing a 1. Writing a 0 has no effect. Bit 3: PRTIRQSTS. printer port IRQ status. Bit 2: FDCIRQSTS. FDC IRQ status. Bit 1: URAIRQSTS. UART A IRQ status. Bit 0: URBIRQSTS. UART B IRQ status. CRF4 (Default 0x00) Bit 7 ~ 4: Reserved. Return zero when read. Bit 3 ~ 0: These bits indicate the IRQ status of the individual GPIO function or logical device respectively. The status bit is set by their source function or device and is cleared by writing a1. Writing a 0 has no effect. Bit 3: HMIRQSTS. Hardware monitor IRQ status. Bit 2: WDTIRQSTS. Watch dog timer IRQ status. Bit 1: CIRIRQSTS. Consumer IR IRQ status. Bit 0: MIDIIRQSTS. MIDI IRQ status. - 84 - W83697HF/ HG CRF6 (Default 0x00) Bit 7 ~ 4: Reserved. Return zero when read. Bit 3 ~ 0: Enable bits of the PME/ SMI generation due to the device's IRQ. These bits enable the generation of an SMI / PME interrupt due to any IRQ of the devices. SMI / PM E logic output = (PRTIRQEN and PRTIRQSTS) or (FDCIRQEN and FDCIRQSTS) or (URAIRQEN and URAIRQSTS) or (URBIRQEN and URBIRQSTS) or (HMIRQEN and HMIRQSTS) or (WDTIRQEN and WDTIRQSTS) or (IRQIN3EN and IRQIN3STS) or (IRQIN2EN and IRQIN2STS) or (IRQIN1EN and IRQIN1STS) or (IRQIN0EN and IRQIN0STS) Bit 3: PRTIRQEN. = 0 disable the generation of an SMI / PME interrupt due to printer port's IRQ. = 1 enable the generation of an SMI / PME interrupt due to printer port's IRQ. Bit 2: FDCIRQEN. = 0 disable the generation of an SMI / PME interrupt due to FDC's IRQ. = 1 enable the generation of an SMI / PME interrupt due to FDC's IRQ. Bit 1: URAIRQEN. = 0 disable the generation of an SMI / PME interrupt due to UART A's IRQ. = 1 enable the generation of an SMI / PME interrupt due to UART A's IRQ. Bit 0: URBIRQEN. = 0 disable the generation of an SMI / PME interrupt due to UART B's IRQ. = 1 enable the generation of an SMI / PME interrupt due to UART B's IRQ. CRF7 (Default 0x00) Bit 7 ~ 4: Reserved. Return zero when read. Bit 3 ~ 0: Enable bits of the SMI / PME generation due to the GPIO IRQ function or device's IRQ. Bit 3: HMIRQEN. = 0 disable the generation of an SMI / PME interrupt due to hardware monitor's IRQ. = 1 enable the generation of an SMI / PME interrupt due to hardware monitor's IRQ. Publication Release Date: May 30, 2005 - 85 - Revision A1 W83697HF/ HG Bit 2: WDTIRQEN. = 0 disable the generation of an SMI / PME interrupt due to watch dog timer's IRQ. = 1 enable the generation of an SMI / SMI interrupt due to watch dog timer's IRQ. Bit 1: CIRIRQEN. PME = 0 disable the generation of an SMI / interrupt due to CIR's IRQ. PME = 1 enable the generation of an SMI / interrupt due to CIR's IRQ. Bit 0: MIDIIRQEN. = 0 disable the generation of an SMI / PME interrupt due to MIDI's IRQ. = 1 enable the generation of an SMI / PME interrupt due to MIDI's IRQ. CRF9 (Default 0x00) Bit 7 - 3: Reserved. Return zero when read. Bit 2: PME_EN: Select the power management events to be either an PME or SMI interrupt for the IRQ events. Note that: this bit is valid only when SMIPME_OE = 1. = 0 the power management events will generate an SMI event. = 1 the power management events will generate an PME event. Bit 1: FSLEEP: This bit selects the fast expiry time of individual devices. = 0 1 S = 1 8 mS. Bit 0: SMIPME_OE: This is the SMI and PME output enable bit. PME = 0 neither SMI nor will be generated. Only the IRQ status bit is set. PME = 1 an SMI or event will be generated. - 86 - W83697HF/ HG 7.14 Logical Device B (Hardware Monitor) CR30 (Default 0x00) Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive. CR60, CR 61 (Default 0x00, 0x00) These two registers select Hardware Monitor base address [0x100:0xFFF] on 8-byte boundary. CR70 (Default 0x00) Bit 7 - 4: Reserved. Bit 3 - 0: These bits select IRQ resource for Hardware Monitor. Publication Release Date: May 30, 2005 - 87 - Revision A1 W83697HF/ HG 8. SPECIFICATIONS 8.1 Absolute Maximum Ratings PARAMETER RATING UNIT Power Supply Voltage (5V) -0.5 to 7.0 V Input Voltage -0.5 to VDD+0.5 V RTC Battery Voltage VBAT 2.2 to 4.0 V Operating Temperature 0 to +70 ° C Storage Temperature -55 to +150 ° C Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device. 8.2 DC CHARACTERISTICS (Ta = 0° C to 70° C, VDD = 5V ± 10%, VSS = 0V) PARAMETER SYM. MIN. TYP.MAX. UNIT CONDITIONS RTC Battery Quiescent IBAT 2.4 uA VBAT = 2.5 V Current ACPI Stand-by Power VSB = 5.0 V, All ACPI pins Supply Quiescent IBAT 2.0 mA are not connected. Current I/O - TTL level bi-directional pin with 8mA source-sink capability 8t Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Output Low Voltage VOL 0.4 V IOL = 8 mA Output High Voltage VOH 2.4 V IOH = - 8 mA Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0V µA I/O - TTL level bi-directional pin with 12mA source-sink capability 12t Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Output Low Voltage VOL 0.4 V IOL = 12 mA Output High Voltage VOH 2.4 V IOH = -12 mA Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 VIN = 0V µA - 88 - W83697HF/ HG 82 DC CHARACTERISTICS, continued PARAMETER SYM. MIN. TYP.MAX. UNIT CONDITIONS I/O - TTL level bi-directional pin with 24mA source-sink capability 24t Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Output Low Voltage VOL 0.4 V IOL = 24 mA Output High Voltage VOH 2.4 V IOH = -24 mA Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0V µA I/O – 3.3V TTL level bi-directional pin with 12mA source-sink capability 12tp3 Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Output Low Voltage VOL 0.4 V IOL = 12 mA Output High Voltage VOH 2.4 V IOH = -12 mA Input High Leakage ILIH +10 µA VIN = 3.3V Input Low Leakage ILIL -10 VIN = 0V µA I/O - TTL level Schmitt-trigger bi-directional pin with 12mA source-sink capability 12ts Input Low Threshold Vt- 0.5 0.8 1.1 V Voltage Input High Threshold Vt+ 1.6 2.0 2.4 V Voltage Hystersis VTH 0.5 1.2 V VDD=5V Output Low Voltage VOL 0.4 V IOL = 12 mA Output High Voltage VOH 2.4 V IOH = -12 mA Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 µA VIN = 0V I/O - TTL level Schmitt-trigger bi-directional pin with 24mA source-sink capability 24ts Input Low Threshold Vt- 0.5 0.8 1.1 V Voltage Input High Threshold Vt+ 1.6 2.0 2.4 V Voltage Hystersis VTH 0.5 1.2 V VDD=5V Output Low Voltage VOL 0.4 V IOL = 24 mA Output High Voltage VOH 2.4 V IOH = -24 Ma Publication Release Date: May 30, 2005 - 89 - Revision A1 W83697HF/ HG 82 DC CHARACTERISTICS, continued MAX PARAMETER SYM. MIN.TYP. UNIT CONDITIONS . Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0V µA I/O – 3.3V TTL level Schmitt-trigger bi-directional pin with 24mA source-sink capability 24tsp3 Input Low Threshold Vt- 0.5 0.8 1.1 V Voltage Input High Threshold Vt+ 1.6 2.0 2.4 V Voltage Hystersis VTH 0.5 1.2 V VDD=3.3V Output Low Voltage VOL 0.4 V IOL = 24 mA Output High Voltage VOH 2.4 V IOH = -24 mA Input High Leakage ILIH +10 VIN = 3.3V µA Input Low Leakage ILIL -10 VIN = 0V µA I/OD - TTL level bi-directional pin and open-drain output with 12mA sink capability 12t Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Output Low Voltage VOL 0.4 V IOL = 12 mA Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0V µA I/OD - TTL level bi-directional pin and open-drain output with 24mA sink capability 24t Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Output Low Voltage VOL 0.4 V IOL = 24 mA Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 µA VIN = 0V I/OD24 - CMOS level bi-directional pin and open drain output with 24mA sink capability c Input Low Voltage VIL 1.5 V Input High Voltage VIH 3.5 V Output Low Voltage VOL 0.4 V IOL = 24 mA Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 µA VIN = 0 V - 90 - W83697HF/ HG 82 DC CHARACTERISTICS, continued PARAMETER SYM. MIN.TYP.MAX.UNIT CONDITIONS I/OD - Bi-directional pin with analog input and open-drain output with 24mA sink 24a capability Output Low Voltage VOL 0.4 V IOL = 24 mA Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 µA VIN = 0V I/OD - TTL level Schmitt-trigger bi-directional pin and open drain output with 12mA sink 12ts capability Input Low Threshold Vt- 0.5 0.8 1.1 V Voltage Input High Threshold Vt+ 1.6 2.0 2.4 V Voltage Hystersis VTH 0.5 1.2 V VDD=5V Output Low Voltage VOL 0.4 V IOL = 12 mA Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 µA VIN = 0V I/OD - TTL level Schmitt-trigger bi-directional pin and open drain output with 24mA sink 24ts capability Input Low Threshold Vt- 0.5 0.8 1.1 V Voltage Input High Threshold Vt+ 1.6 2.0 2.4 V Voltage Hystersis VTH 0.5 1.2 V VDD=5V Output Low Voltage VOL 0.4 V IOL = 24 mA Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0V µA I/OD12 - CMOS level Schmitt-trigger bi-directional pin and open drain output with 12mA cs sink capability Input Low Threshold Vt- 1.3 1.5 1.7 V VDD = 5 V Voltage Input High Threshold Vt+ 3.2 3.5 3.8 V VDD = 5 V Voltage Hystersis VTH 1.5 2 V VDD = 5 V Output Low Voltage VOL 0.4 V IOL = 12 mA Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 µA VIN = 0 V Publication Release Date: May 30, 2005 - 91 - Revision A1 W83697HF/ HG 82 DC CHARACTERISTICS, continued PARAMETER SYM. MIN.TYP.MAX.UNIT CONDITIONS I/OD16 - CMOS level Schmitt-trigger bi-directional pin and open drain output with 16mA cs sink capability Input Low Threshold Vt- 1.3 1.5 1.7 V VDD = 5 V Voltage Input High Threshold Vt+ 3.2 3.5 3.8 V VDD = 5 V Voltage Hystersis VTH 1.5 2 V VDD = 5 V Output Low Voltage VOL 0.4 V IOL = 16 mA Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0 V µA I/OD24 - CMOS level Schmitt-trigger bi-directional pin and open drain output with 24mA cs sink capability Input Low Threshold Vt- 1.3 1.5 1.7 V VDD = 5 V Voltage Input High Threshold Vt+ 3.2 3.5 3.8 V VDD = 5 V Voltage Hystersis VTH 1.5 2 V VDD = 5 V Output Low Voltage VOL 0.4 V IOL = 24 mA Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0 V µA I/OD12 - CMOS level Schmitt-trigger bi-directional pin with internal pull down resistor and csd open drain output with 12mA sink capability Input Low Threshold Vt- 1.3 1.5 1.7 V VDD = 5 V Voltage Input High Threshold Vt+ 3.2 3.5 3.8 V VDD = 5 V Voltage Hystersis VTH 1.5 2 V VDD = 5 V Output Low Voltage VOL 0.4 V IOL = 12 mA Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 µA VIN = 0 V I/OD12 - CMOS level Schmitt-trigger bi-directional pin with internal pull up resistor and csu open drain output with 12mA sink capability Input Low Threshold Vt- 1.3 1.5 1.7 V VDD = 5 V Voltage Input High Threshold Vt+ 3.2 3.5 3.8 V VDD = 5 V Voltage Hystersis VTH 1.5 2 V VDD = 5 V Output Low Voltage VOL 0.4 V IOL = 12 mA Input High Leakage ILIH +10 µA VIN = 5V - 92 - W83697HF/ HG 82 DC CHARACTERISTICS, continued PARAMETER SYM.MIN.TYP.MAX.UNIT CONDITIONS Input Low Leakage ILIL -10 µA VIN = 0 V O4 - Output pin with 4mA source-sink capability Output Low Voltage VOL 0.4 V IOL = 4 mA Output High Voltage VOH 2.4 V IOH = -4 mA O8 - Output pin with 8mA source-sink capability Output Low Voltage VOL 0.4 V IOL = 8 mA Output High Voltage VOH 2.4 V IOH = -8 mA O12 - Output pin with 12mA source-sink capability Output Low Voltage VOL 0.4 V IOL = 12 mA Output High Voltage VOH 2.4 V IOH = -12 mA O16 - Output pin with 16mA source-sink capability Output Low Voltage VOL 0.4 V IOL = 16 mA Output High Voltage VOH 2.4 V IOH = -16 mA O24 - Output pin with 24mA source-sink capability Output Low Voltage VOL 0.4 V IOL = 24 mA Output High Voltage VOH 2.4 V IOH = -24 mA O - 3.3V output pin with 12mA source-sink capability 12p3 Output Low Voltage VOL 0.4 V IOL = 12 mA Output High Voltage VOH 2.4 V IOH = -12 mA O - 3.3V output pin with 24mA source-sink capability 24p3 Output Low Voltage VOL 0.4 V IOL = 24 mA Output High Voltage VOH 2.4 V IOH = -24 mA OD8 - Open drain output pin with 8mA sink capability Output Low Voltage VOL 0.4 V IOL = 8 mA OD12 - Open drain output pin with 12mA sink capability Output Low Voltage VOL 0.4 V IOL = 12 mA OD24 - Open drain output pin with 24mA sink capability Output Low Voltage VOL 0.4 V IOL = 24 mA OD12p3 - 3.3V open drain output pin with 12mA sink capability Output Low Voltage VOL 0.4 V IOL = 12 mA Publication Release Date: May 30, 2005 - 93 - Revision A1 W83697HF/ HG 82 DC CHARACTERISTICS, continued PARAMETER SYM.MIN. TYP. MAX.UNIT CONDITIONS IN - TTL level input pin t Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0 V µA IN - 3.3V TTL level input pin tp3 Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Input High Leakage ILIH +10 µA VIN = 3.3V Input Low Leakage ILIL -10 µA VIN = 0 V IN - TTL level input pin with internal pull down resistor td Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 µA VIN = 0 V IN - TTL level input pin with internal pull up resistor tu Input Low Voltage VIL 0.8 V Input High Voltage VIH 2.0 V Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0 V µA IN - TTL level Schmitt-trigger input pin ts Input Low Threshold Voltage Vt- 0.8 0.9 1.0 V VDD = 5 V Input High Threshold Voltage Vt+ 1.8 1.9 2.0 V VDD = 5 V Hystersis VTH 0.8 1.0 V VDD = 5 V Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0 V µA IN - 3.3 V TTL level Schmitt-trigger input pin tsp3 Input Low Threshold Voltage Vt- 0.8 0.9 1.0 V VDD = 3.3 V Input High Threshold Voltage Vt+ 1.8 1.9 2.0 V VDD = 3.3 V Hystersis VTH 0.8 1.0 V VDD = 3.3 V Input High Leakage ILIH +10 VIN = 3.3 V µA Input Low Leakage ILIL -10 VIN = 0 V µA - 94 - W83697HF/ HG 82 DC CHARACTERISTICS, continued PARAMETER SYM. MIN. TYP.MAX.UNIT CONDITIONS IN - CMOS level input pin c Input Low Voltage VIL 1.5 V Input High Voltage VIH 3.5 V Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0 V µA IN - CMOS level input pin with internal pull up resistor cu Input Low Voltage VIL 1.5 V Input High Voltage VIH 3.5 V Input High Leakage ILIH +10 µA VIN = 5V Input Low Leakage ILIL -10 µA VIN = 0 V IN - CMOS level input pin with internal pull down resistor cd Input Low Voltage VIL 1.5 V Input High Voltage VIH 3.5 V Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0 V µA IN - CMOS level Schmitt-trigger input pin cs Input Low Threshold Vt- 1.3 1.5 1.7 V VDD = 5 V Voltage Input High Threshold Vt+ 3.2 3.5 3.8 V VDD = 5 V Voltage Hystersis VTH 1.5 2 V VDD = 5 V Input High Leakage ILIH +10 µA VIN = 5 V Input Low Leakage ILIL -10 µA VIN = 0 V IN - CMOS level Schmitt-trigger input pin with internal pull up resistor csu Input Low Threshold Vt- 1.3 1.5 1.7 V VDD = 5 V Voltage Input High Threshold Vt+ 3.2 3.5 3.8 V VDD = 5 V Voltage Hystersis VTH 1.5 2 V VDD = 5 V Input High Leakage ILIH +10 VIN = 5V µA Input Low Leakage ILIL -10 VIN = 0 V µA Publication Release Date: May 30, 2005 - 95 - Revision A1 W83697HF/ HG 9. APPLICATION CIRCUITS 9.1 Parallel Port Extension FDD JP13 13 WE2/SLCT 25 12 JP 13A WD2/PE 24 DCH2 34 33 11 MOB2/BUSY HEAD2 32 31 23 RDD2 30 29 10 WP2 DSB2/ACK 22 28 27 TRK02 9 26 25 PD7 WE2 21 24 23 WD2 8 22 21 PD6 STEP2 20 20 19 DIR2 7 18 17 PD5 MOB2 19 16 15 6 14 13 DCH2/PD4 DSB2 18 12 11 RDD2/PD3 10 9 5 IDX2 17 8 7 STEP2/SLIN 4 6 5 WP2/PD2 16 4 3 RWC2 DIR2/INIT 3 2 1 TRK02/PD1 15 EXT FDC HEAD2/ERR 2 IDX2/PD0 14 RWC2/AFD 1 STB PRINTER PORT Parallel Port Extension FDD Mode Connection Diagram - 96 - W83697HF/ HG 9.2 Parallel Port Extension 2FDD JP13 13 WE2/SLCT 25 JP 13A 12 WD2/PE DCH2 24 34 33 MOB2/BUSY 11 HEAD2 32 31 23 RDD2 30 29 10 WP2 DSB2/ACK 28 27 22 TRK02 26 9 25 DSA2/PD7 WE2 24 21 23 WD2 8 22 21 MOA2/PD6 STEP2 20 20 19 DIR2 7 18 17 PD5 MOB2 16 19 15 DSA2 14 13 6 DCH2/PD4 DSB2 12 11 18 MOA2 RDD2/PD3 10 9 5 IDX2 8 7 STEP2/SLIN 17 6 5 4 WP2/PD2 4 3 16 RWC2 DIR2/INIT 2 1 3 TRK02/PD1 15 EXT FDC HEAD2/ERR 2 IDX2/PD0 14 RWC2/AFD 1 STB PRINTER PORT Parallel Port Extension 2FDD Connection Diagram 9.3 Four FDD Mode 74LS139 7407(2) W83977F G1 1Y0 DSA DSA A1 1Y1 DSB B1 1Y2 DSC DSB 1Y3 DSD 2Y0 MOA MOA 2Y1 MOB G2 MOB 2Y2 MOC 2Y3 A2 MOD B2 Publication Release Date: May 30, 2005 - 97 - Revision A1 W83697HF/ HG 10. ORDERING INSTRUNCTION PART NO. PACKAGE REMARKS W83697HF/W83697HG 128-pin QFP W83697HG is Pb-free package 11. HOW TO READ THE TOP MARKING Example: The top marking of W83697HF inbond W83697HF 421A2B28201234 Example: The top marking of W83697HG inbond W83697HG 421A2B28201234 1st line: Winbond logo 2nd line: the type number: W83697HF, W83697HG 3th line: the tracking code 421 A 2 C 28201234 421: packages made in '04, week 21 A: assembly house ID; A means ASE, S means SPIL.... etc. 2: Winbond internal use. B: IC revision; A means version A, B means version B 282012345: wafer production series lot number - 98 - W83697HF/ HG 12. PACKAGE DIMENSIONS (128-pin PQFP) Dimension in mm Dimension in inch H E Symbol Min Nom Max Min Nom Max E 102 65 A1 0.25 0.35 0.45 0.010 0.014 0.018 A2 2.57 2.72 2.87 0.101 0.107 0.113 103 64 b 0.10 0.20 0.30 0.004 0.008 0.012 0.20 0.004 0.006 0.008 c 0.10 0.15 D 13.90 14.00 14.10 0.547 0.551 0.555 19.90 20.00 20.10 0.783 0.787 0.791 E D HD e 0.50 0.020 HD 17.20 0.669 0.677 0.685 17.00 17.40 23.00 23.20 0.905 0.913 0.921 H 23.40 E 0.95 L 0.65 0.80 0.025 0.031 0.037 128 39 1.60 0.063 L 1 y 0.08 0.003 1 38 e b 7 0 7 0 0 c Note: A 1.Dimension D & E do not include interlead flash. A2 2.Dimension b does not include dambar protrusion/intrusion . See Detail F A1 3.Controlling dimension : Millimeter L y Seating Plane 4.General appearance spec. should be based L 1 on final visual inspection spec. Detail F 5. PCB layout please use the "mm". Publication Release Date: May 30, 2005 - 99 - Revision A1 W83697HF/ HG 13. APPENDIX A : DEMO CIRCUIT XD0 XD1 W83697HF XD2 XD3 XD[0..7] XD[0..7] XD4 XD5 XD6 XD7 XA0 XA1 XA2 XA3 XA4 ROMCS# XA5 MEMR# XA6 MEMW# XA7 PME# XA8 CIRRX XA9 XA[0..18] CASEOPEN XA[0..18] XA10 XA11 XA12 XA13 5VSB (To monitor battery voltage, XA14 VBAT this input should be XA15 VCC connected directly to XA16 battery) XA17 C1 C2 C3 XA18 0.1u 0.1u 0.1u IRTX C4 R1 4.7K IR VCC3V 0.1u 103 64 & VTIN2 VTIN2 IRRX IRRX Temperature Sensing 104 63 VTIN1 VTIN1 RIB# RIB# 105 62 AVCC AVCC DCDB# DCDB# 106 61 COMB VREF VREF SOUTB SOUTB 107 60 VCORE VCORE GND 108 59 SINB +3.3VIN +3.3VIN SINB Voltage SENSING 109 58 DTRB# +12VIN +12VIN DTRB# 110 57 RTSB# -12VIN -12VIN RTSB# 111 56 -5VIN -5VIN U1 DSRB# DSRB# 112 55 AGND AGND CTSB# CTSB# 113 54 FANIO2 FANIO2 RIA# RIA# Fan Speed Seneing 114 53 FANIO1 FANIO1 W83697HF DCDA# DCDA# & Speed Control 115 52 FANPWM2 FANPWM2 SOUTA SOUTA 116 51 FANPWM1 FANPWM1 SINA SINA 117 50 COMA OVT# OVT#/SMI# DTRA# DTRA# 118 49 BEEP BEEP RTSA# RTSA# 119 48 DSRA# MSI MSI/GP51/WDTO DSRA# MIDI PORT 120 47 CTSA# MSO MSO/GP50/PLED CTSA# 121 46 STB# GPAS2 GSAS2/GP17 STB# 122 45 GPBS2 GPBS2/GP16 VCC VCC 123 44 GPAY GPAY/GP15 AFD# AFD# 124 43 GPBY GPBY/GP14 INIT# INIT# GAME PORT 125 42 GPBX GPBX/GP13 PD0 126 41 GPAX GPAX/GP12 PD1 127 40 GPBS1 GPBS1/GP11 PD2 128 39 C5 GPAS1 GPAS1/GP10 PD3 CAP NP 0.1u Printer PD0 PD1 PD[0..7] PD[0..7] PD2 J1 1 2 RWC# PD3 1 2 3 4 PD4 3 4 5 6 PD5 5 6 7 8 INDEX# PD6 7 8 9 10 MOA# PD7 9 10 11 12 DSB# SLIN# 11 12 13 14 DSA# ERR# 13 14 15 16 MOB# 15 16 ACK# 17 18 DIR# 17 18 BUSY 19 20 STEP# 19 20 PE 21 22 WD# 21 22 SLCT 23 24 WE# VCC3V 23 24 25 26 TRAK0# 25 26 27 28 WP# C6 27 28 29 30 RDATA# 0.1u 29 30 31 32 HEAD# |LINK 31 32 33 34 DSKCHG# |697HD2.SCH 33 34 OSC1 C7 |697HD3.SCH 0.1u |697HD4.SCH HEADER 17X2 1 NC |697HD5.SCH VCC 5 OUTPUT PCICLK 24/48MHz LDRQ# VCC3V R2 R FDC R3 R 4.7K SERIRQ LAD3 Winbond Electronic Corp. VCC3V LAD2 4.7K LAD[0..3] LAD1 LAD[0..3] LAD0 Title W83697HF (LPC I/O + H/W + FLASH ROM I/N) LFRAME# Size Document Number Rev LRESET# B 697HD1.SCH 0.4 Date: Thursday, July 11, 2002 Sheet15 of - 100 - 1 102 DRVDEN0 VBAT 2 101 INDEX# CASEOPEN 3 100 MOA# CIRRX 4 99 DSB# VSB 5 98 VCC PME# 6 97 DSA# MEMW#/GP52 7 96 MOB# MEMR#/GP53 8 95 DIR# ROMCS#/GP54 9 94 STEP# XD0/GP20 10 93 WD# XD1/GP21 11 92 WE# XD2/GP22 12 91 TRAK0# XD3/GP23 13 90 WP# GND 14 89 RDATA# XD4/GP24 15 88 HEAD# XD5/GP25 16 87 DSKCHG# XD6/GP26 17 86 CLKIN XD7/GP27 18 85 GND XA0/GP30 19 84 PCICLK XA1/GP31 20 83 LDRQ# XA2/GP32 21 82 SERIRQ XA3/GP33 22 81 VCC3 XA4/GP34 23 80 LAD3 XA5/GP35 24 79 LAD2 XA6/GP36 25 78 LAD1 XA7/GP37 26 77 LAD0 XA8/GP40 27 76 LFRAME# XA9/GP41 28 75 LRESET# VCC 29 74 SLCT XA10/GP42 30 73 PE XA11/GP43 31 72 BUSY XA12/GP44 32 71 ACK# XA13/GP45 33 70 ERR# XA14/GP46 34 69 SLIN# XA15/GP47 35 68 PD7 XA16/GP55 36 67 PD6 XA17/GP56 37 66 PD5 XA18/GP57 38 65 PD4 IRTX W83697HF/ HG COM PORT U2 20 1 VCC VCC +12V +12V IR/CIR CONNECTOR 16 5 NRTSA RTSA# DA1 DY1 15 6 NDTRA DTRA# DA2 DY2 13 8 NSOUTA J2 SOUTA DA3 DY3 19 2 NRIA NDCDA NSINA RIA# RY1 RA1 1 2 18 3 NCTSA NSOUTA NDTRA CTSA# RY2 RA2 3 4 17 4 NDSRA GND NDSRA VCC DSRA# RY3 RA3 5 6 14 7 NSINA NRTSA NCTSA J4 SINA RY4 RA4 7 8 12 9 NDCDA NRIA DCDA# RY5 RA9 9 10 1 6 2 7 CIRRX 11 10 CN2X5B -12V GND -12V IRRX 3 8 IOVSB 4 9 W83778 COMA (UARTA) IRTX 5 10 (SOP20) CN2X5 U3 J3 20 1 NDCDB NSINB VCC +12V VCC +12V 1 2 NSOUTB NDTRB 3 4 16 5 NRTSB GND NDSRB RTSB# DA1 DY1 5 6 15 6 NDTRB NRTSB NCTSB DTRB# DA2 DY2 7 8 THE IOVSB OF PIN 8 IS FOR CIR WAKE-UP FUNCTION. 13 8 NSOUTB NRIB SOUTB DA3 DY3 9 10 19 2 NRIB RIB# RY1 RA1 18 3 NCTSB CN2X5B CTSB# RY2 RA2 17 4 NDSRB DSRB# RY3 RA3 14 7 NSINB SINB RY4 RA4 12 9 NDCDB COMB (UARTB) DCDB# RY5 RA9 11 10 GND -12V -12V W83778 (SOP20) VCC VCC PRT PORT RP1 RP2 10P9R-2.7K 10P9R-2.7K RPACK1 1 2 STB# 3 4 AFD# 5 6 J5 INIT# 7 8 1 SLIN# 14 PD[0..7] 33 2 PD[0..7] 15 RPACK2 3 PD0 1 2 16 PD1 3 4 4 PD2 5 6 17 PD3 7 8 5 18 33 6 19 RPACK3 7 PD4 1 2 20 PD5 3 4 8 PD6 5 6 21 PD7 7 8 9 22 33 10 23 11 ERR# 24 ACK# 12 BUSY 25 PE 13 SLCT DB25 C8 C10 C12 C14 C16 C18 C20 C22 C24 180 180 180 180 180 180 180 180 180 C9 C11 C13 C15 C17 C19 C21 C23 180 180 180 180 180 180 180 180 WINBOND ELECTRONICS CORP. Title W83697HF (LPC I/O + H/W + FLASH ROM I/F) Size Document Number Rev B 697HD2.SCH 0.4 Date: Thursday, July 11, 2002 Sheet25 of Publication Release Date: May 30, 2005 - 101 - Revision A1 2 1 3 4 5 6 7 8 9 10 2 1 3 4 5 6 7 8 9 10 W83697HF/ HG BATTERY CIRCUIT GAME & MIDI PORT CIRCUIT VBAT IO5V IO5V IO5V IO5V IO5V IO5V IO5V BT1 R4 BATTERY 1K L1 R21 R24 R23 R20 R22 INDUCTOR C25 100K 2.2K 2.2K 2.2K 2.2K 0.1UF P1 JP1 8 JP5:1-2 Clear CMOS HEAD3 R14 2.2K 15 MSI 7 2-3 Enable ONNOW functions GPSA2 14 GPSB2 R15 2.2K 6 GPY1 R16 2.2K 13 GPY2 5 R17 2.2K 12 MSO 4 R18 2.2K 11 GPX2 R19 2.2K 3 GPX1 10 GPSB1 2 GPSA1 9 1 R10 R11 R12 R13 PRT 1M 1M 1M 1M C32 0.01U C33 C34 C36 C35 0.01U 0.01U 0.01U 0.01U C28 C29 C30 C31 0.01U 0.01U 0.01U 0.01U FLASH ROM IOVSB CIRCUIT SELECT 2M-FLASH ROM, UNINSTALL R19 R9 OnNow or Wake_up function power SELECT 4M-FLASH ROM, INSTALL R19 R23 OFF, D1,D2 ON: Wake_up fuction 0 R23 ON, D1,D2 OFF:NO Wake_up fuction U4 D1 VCC IOVSB 1 13 XD0 NC/A18 DQ0 XA17 30 14 XD1 C27 5817 A17 DQ1 XA16 2 15 XD2 XD[0..7] 10u R5 A16 DQ2 XD[0..7] XA18 XA15 3 17 XD3 A15 DQ3 XA14 29 18 XD4 A14 DQ4 0 XA13 28 19 XD5 D2 A13 DQ5 XA12 4 20 XD6 A12 DQ6 5VSB XA11 25 21 XD7 A11 DQ7 XA10 23 5817 A10 XA9 26 A9 XA[0..18] XA8 27 XA[0..18] A8 XA7 5 A7 VCC XA6 6 A6 XA5 7 A5 XA4 8 A4 XA3 9 A3 XA2 10 A2 R6 R7 R8 XA1 11 VCC A1 4.7K 4.7K 4.7K XA0 12 A0 32 VCC 31 MEMW# WE# 24 16 MEMR# OE# GND 22 ROMCS# CE# CAP NP W29C020/40 0.1u C26 WINBOND ELECTRONICS CORP. Title W83697HF (LPC I/O + H/W + FLASH ROM I/F) Size Document Number Rev B 697HD3.SCH 0.4 Date: Thursday, July 11, 2002 Sheet35 of - 102 - 3 2 1 W83697HF/ HG Hardware Monitor circuits Temperature Sensing Voltage Sensing R32 R31 56K 1% -12V 232K 1% R27 R CPUVCOA VCORE 10K -12VIN VREF RT1 10K 1% R25 10K 1% -5VIN VREF R28 R (for system) VCC3V +3.3VIN THERMISTOR 10K R34 R33 56K 1% -5V VTIN1 +12VIN 120K 1% R R29 R30 R +12V AGND 28K 1% 10K 1% R26 30K D+ D+ (from Deschutes) D- VTIN2 D- AGND C39 3300P Beep Circuits PWM Circuit for FAN speed control VCC +12V R35 4.7K R47 100 Q1 R36 1K PNP D3 LS1 1N4148 R37 3906 4.7K R46 10K JP2 SPEAKER C37 R38 27K Q2 + 3 FANIO1 R48 510 MOSFET N Q5 FANPWM1 2 BEEP 2N7002 10u R39 3904 1 10K HEADER 3 +12V R41 4.7K Q3 R42 1K D4 PNP 3906 1N4148 R43 4.7K JP3 C38 R44 27K Q4 + FANIO2 R40 510 3 MOSFET N FANPWM2 10u 2 2N7002 R45 1 10K HEADER 3 L2 VCC AVCC FB L3 AGND FB R49 VBAT CASEOPEN# 2M Winbond Electronic Corp. S1 CASEOPEN SW Title W83697HF (LPC I/O+ H/W + FLASH ROM I/F) Size Document Number Rev B 697HD4.SCH 0.4 Date: Thursday, July 11, 2002 Sheet45 of Publication Release Date: May 30, 2005 - 103 - Revision A1 T W83697HF/ HG The version 0.1 is first schematics for W83697HF The version 0.2 change 1.update 697's library 2.The sheet 4 in Case open block,part 74HC14 is U4A & U4B changed to U5A & U5B The version 0.3 chage 1.Case-Open circuit(in page 4) The version 0.4 chage add a pull high resistor 100K in midiin(in page 3) WINBOND ELECTRONICS CORP. Title W83627HF (LPC I/O + H/W + FLASH ROM I/F) Size Document Number Rev B CHANGED NOTICS 0.3 Date: Thursday, July 11, 2002 Sheet55 of - 104 - W83697HF/ HG 14. REVISION HISTORY VERSION DATE PAGE DESCRIPTION First published. 0.40 08/23/99 n.a. For Beta Site customers only H/W monitor register correction 0.41 11/15/99 98, 107, 116 New composition 0.50 11/15/00 All   New update 1.0 12/17/02 1.1 02/18/03 5,6   Add Block Diagram   1.Add pin buffer type description ofOD8. 1.P7   2.Update the functional description of   Pin117~126. 2.P17~18   3. Update the chip control register CR29   4. Add VOH of O12p3,O24p and OD8 3.P74   description in DC specification   5. The pin name WDTO” were replaced by 1.2    WDTO#” 4.P99   6 H/W monitor data correction 12/01/04 Add Pb-free part no of W83697HG 1.3 A1 May 30, 2005 106 ADD Important Notice Publication Release Date: May 30, 2005 - 105 - Revision A1 W83697HF/ HG Important Notice Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Winbond products are not intended for applications wherein failure of Winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales. Headquarters Winbond Electronics Corporation America Winbond Electronics (Shanghai) Ltd. No. 4, Creation Rd. III, 2727 North First Street, San Jose, 27F, 2299 Yan An W. Rd. Shanghai, Science-Based Industrial Park, CA 95134, U.S.A. 200336 China Hsinchu, Taiwan TEL: 1-408-9436666 TEL: 86-21-62365999 TEL: 886-3-5770066 FAX: 1-408-5441798 FAX: 86-21-62365998 FAX: 886-3-5665577 http://www.winbond.com.tw/ Taipei Office Winbond Electronics Corporation Japan Winbond Electronics (H.K.) Ltd. 9F, No.480, Rueiguang Rd., 7F Daini-ueno BLDG, 3-7-18 Unit 9-15, 22F, Millennium City, Neihu District, Taipei, 114, Shinyokohama Kohoku-ku, No. 378 Kwun Tong Rd., Taiwan, R.O.C. Yokohama, 222-0033 Kowloon, Hong Kong TEL: 886-2-8177-7168 TEL: 81-45-4781881 TEL: 852-27513100 FAX: 886-2-8751-3579 FAX: 81-45-4781800 FAX: 852-27552064 Please note that all data and specifications are subject to change without notice. All the trade marks of products and companies mentioned in this data sheet belong to their respective owners. - 106 -

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the W83697HG have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

product

Winbond W24L257AJ-12 Integrated Circuit - 16K X 8 High Speed CMOS Static RAM

product

Winbond W29C011A-15 Memory Module - 1-megabit, 5-volt only CMOS flash memory with a standard 5V powe...

product

Winbond W29C011AP-15 128K x 8 CMOS Flash Memory

product

Winbond W83877TF Enhanced I/O Chip - Integrated I/O, high speed communication ports,

product

Winbond W83977ATF INTEGRATED I/O CONTROLLER

product

Winbond W83977EF-AW Chipset - INTEGRATED I/O CONTROLLER WITHQFP128