NFS110 SERIES AC/DC Single & Multi Output: 110Watts LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110 W AC/DC Universal Input Switch Mode Power Supplies 1 • 7.0 x 4.25 x 1.8 inch package • Overvoltage and short circuit protection • 110 W with 20 CFM • Adjustable outputs • EN55022, EN55011 conducted emissions level B • UL, VDE and CSA safety approvals • CE mark • Available RoHS compliant The NFS110 series is a 110 W universal input ac-dc power supply on a 7 x 4.25 inch card. The NFS110 series has four single and three quad output models and has proven itself to be highly reliable and versatile product for a wide range of communication and industrial applications, with a very high peak current capability on each output for drive and motor applications. The NFS110 provides 80 W of output power with free air convection cooling which can be boosted to 110 W with 20 CFM of air. Standard features include overvoltage and short circuit protection. The series, with full international safety approval and the CE mark, meets conducted emissions EN55022 level B. The NFS110 series is designed for use in low power data networking, computer, telecom and industrial applications such as servers, thermal printers, storage devices, vending machines and POS equipment. 2 YEAR WARRANTY All specifications are typical at nominal input, full load at 25 °C unless otherwise stated SPECIFICATIONS OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Voltage adjustability +5.1 V o/p on multi’s ±3.0% Hold-up time 110 Vac @ 80 W 35 ms 5.1 V single output ±3.0% 110 Vac @ 110 W 17 ms 12 V single output 12-14 Vac 230 Vac @ 80 W 140 ms 15 V single output 15-18 Vac 230 Vac @ 110 W 100 ms 24 V single output 24-30 Vac Efficiency Multiple outputs 70% typical Line regulation LL to HL, FL ±0.1% max. +5.1 V single 70% typical All outputs on all units 12 V and 15 V singles 72% typical 24 V single 75% typical Overshoot/undershoot At turn-on 0% Isolation voltage Input/output 3000 Vac Temperature coefficient All outputs ±0.02%/°C Input/chassis 1500 Vac Overvoltage protection Multi o/p 5.1 Vac only 6.25 Vac ±0.75 Vac Switching frequency At 100 Watts output 20-70 kHz 5.1 Vac single 6.25 Vac ±0.75 Vac At zero load 100-250 kHz 12 Vac single 15.75 Vac ±1.0 Vac 15 Vac single 22 Vac ±1.5 Vac Approvals and VDE0805, EN60950, IEC950 24 Vac single 33 Vac ±2.5 Vac standards IEC1010, UL1950 (See Note 12) CSA C22.2 No. 950 Output power limit Primary power Pin max. 160 W limited Pout min. 110 W Weight Singles 550 g (19.4 oz) Multiple outputs 600 g (21.2 oz) Minimum output current (See Note 13) 0 A MTBF (See Note 9) MIL-HDBK-217E 125,000 hours Short circuit protection Burst mode operation ENVIRONMENTAL SPECIFICATIONS INPUT SPECIFICATIONS Thermal performance Operating, see curve 0 °C to +70 °C (See Notes 9, 10) Non-operating –40 °C to +85 °C Input voltage range 85-264 Vac 120-370 Vdc 0 °C to +50 °C, 80 W amb. convection cooled Input frequency range 47-440 Hz +50 °C to +70 °C, Derate 2 W/°C amb. convection cooled Input surge current 230 Vac 35 A 0 °C to +50 °C, 110 W 20 CFM forced air Safety ground 110 Vac, 50 Hz 0.2 mA, max. leakage current 230 Vac, 50 Hz 0.4 mA, max. +50 °C to +70 °C, Derate 20 CFM forced air 2.75 W/°C Peak, 0 °C to +50 °C, 110 W EMC CHARACTERISTICS max. 60 seconds Conducted emissions EN55022, FCC part 15 Level B Relative humidity Non-condensing 5% to 95% RH Radiated emissions EN55022, FCC part 15 Level A ESD air EN61000-4-2, level 3 Perf. criteria 1 Altitude Operating 10,000 feet max. ESD contact EN61000-4-2, level 4 Perf. criteria 1 Non-operating 40,000 feet max. Surge EN61000-4-5, level 3 Perf. criteria 1 Fast transients EN61000-4-4, level 3 Perf. criteria 1 Vibration (See Note 11) 5-500 Hz 2.4 G approx. Radiated immunity EN61000-4-3, level 3 Perf. criteria 2 File Name: nfs110.pdf Rev (02): 08 Nov 2005 Conducted immunity EN61000-4-6, level 3 Perf. criteria 1 REV23-07-07 NFS110 SERIES AC/DC Single & Multi Output: 110Watts LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110 W AC/DC Universal Input Switch Mode Power Supplies 2 OUTPUT CURRENTS OUTPUT TOTAL (4) (13,14,F) RIPPLE MODEL NUMBERS (5) VOLTAGE REGULATION (1) (2) (3) MAX PEAK FAN +5.1 V 8 A 20 A 10 A 50 mV ±2.0% NFS110-7601PJ +12 V 4.5 A 9 A 5 A 120 mV ±3.0% –12 V 0.5 A 1.5 A 1 A 120 mV ±3.0% –5 V 0.5 A 1.5 A 1 A 50 mV ±3.0% (6) +5.1 V (I ) 8 A 20 A 10 A 50 mV ±2.0% NFS110-7602PJ A (6) +24 V (I ) 3.5 A 4.5 A 4.5 A 240 mV +10/–5.0% B +12 V 4.5 A 9 A 5 A 120 mV ±3.0% –12 V 0.5 A 1.5 A 1 A 120 mV ±3.0% +5.1 V 8 A 20 A 10 A 50 mV ±2.0% NFS110-7604PJ +15 V 4 A 7.5 A 5 A 150 mV ±3.0% –15 V 0.5 A 1.5 A 1 A 150 mV ±3.0% –5 V 0.5 A 1.5 A 1 A 50 mV ±3.0% (7,8) 5.1 V 16 A 22 A 20 A 50 mV ±2.0% NFS110-7605J (7,8) 12 V 7 A 9 A 9 A 120 mV ±2.0% NFS110-7612J (7,8) 15 V 5 A 7.3 A 7.3 A 150 mV ±2.0% NFS110-7615J (7,8) 24 V 3.5 A 4.5 A 4.5 A 240 mV ±2.0% NFS110-7624J Notes TRANSIENT RESPONSE 1 Convection cooled, 80 W maximum. NFS110-7601PJ +5.1 V (7.5 A to 10 A) 150 mV peak, 2 Peak outputs lasting less than 60 seconds with duty cycle less than 10%. 1 ms recovery Total peak power must not exceed 110 W. +12 V (2.5 A to 5 A) 100 mV peak, 3 Forced air, 20 CFM at 1 atmosphere, 110 W maximum. 0.5 ms recovery 4 Figure is peak-to-peak. Output ripple is measured across a 50 MHz -12 V (0.5 A to 1 A) 100 mV peak, bandwidth using a 12 inch twisted pair terminated with a 47 μF capacitor. 0.5 ms recovery 5 Total regulation is defined as the static output regulation at 25 °C, including -5 V (0.5 A to 1 A) 100 mV peak, initial tolerance, line voltage within stated limits and output voltages 0.5 ms recovery adjusted to their factory settings. 6 To achieve stated regulation on the 24 V output on the NFS110-7602PJ, NFS110-7602PJ +5.1V (7.5 A to 10 A) 150 mV peak, the following load condition must be true: I / I ≤ 5, where: A B 1 ms recovery I = +5.1 V output current, and A +24 V (1.5 A to 3 A) 300 mV peak, I = +24 V output current B 1 ms recovery The +24 V output will maintain ±5.0% regulation under the following +12 V (2.5 A to 5 A) 100 mV peak, additional condition: I ≤5 A. A 0.5 ms recovery 7 Single output models have floating outputs which may be referenced as -12 V (0.5 A to 1 A) 100 mV peak, either positive or negative. Higher voltage supplies may be adjusted over a 0.5 ms recovery wide output voltage range, as long as the total output power does not exceed 80 Watts (natural convection) or 110 Watts (forced air). NFS110-7604PJ +5.1 V (7.5 A to 10 A) 150 mV peak, 8 Power fail detect not available on single output models. 1 ms recovery 9 Derating curve is application specific for ambient temperatures >50 °C, for +15 V (2.5 A to 5 A) 100 mV peak, optimum reliability no part of the heatsink should exceed 90 ºC and no 0.5 ms recovery semiconductor case temperature should exceed 100 ºC. -15 V (0.5 A to 1 A) 100 mV peak, 10 Caution: Allow a minimum of 1 second after disconnecting the power when 0.5 ms recovery making thermal measurements. -5 V (0.5 A to 1 A) 100 mV peak, 11 Three orthogonal axes, random vibration, 10 minute test for each axis. 0.5 ms recovery 12 This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. NFS110-7605J +5.1 V (10 A to 20 A) 250 mV peak, 13 Artesyn Technologies recommends a minimum load of 11 W to achieve the 1 ms recovery design MTBF. See the derating curve on page 3. 14 The ‘J’ suffix indicates that these parts are Pb-free (RoHS 6/6) compliant. NFS110-7612J +12 V (4.5 A to 9 A) 360 mV peak, TSE RoHS 5/6 (non Pb-free) compliant versions may be available on 1 ms recovery special request, please contact your local sales representative for details. 15 NOTICE: Some models do not support all options. Please contact your NFS110-7615J +15 V (3.65 A to 7.3 A) 450 mV peak, local Artesyn representative or use the on-line model number search tool at 1 ms recovery http://www.artesyn.com/powergroup/products.htm to find a suitable alternative. NFS110-7624J +24V (2.25 A to 4.5 A) 720 mV peak, 1 ms recovery File Name: nfs110.pdf Rev (02): 08 Nov 2005 NFS110 SERIES AC/DC Single & Multi Output: 110Watts LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110W AC/DC Universal Input Switch Mode Power Supplies 3 AC (J1) mating connector Power fail detect signal (Note 8) OPTIONAL POWER FAIL DETECT TIMING DIAGRAM Molex 09-50-3051 or Molex 09-91-0500 mating connector with 2478 or 50 ms≤T1≤200 ms equivalent crimp terminals. T2 will vary with line and load AC INPUT T3≥3 ms 4.75V 4.75V Pout: 110 W 5V OUTPUT DC (J2) mating connector PFD output is an open collector which Molex 09-50-3131 or Molex 09-91-1300 mating connector with 2478 or HIGH 3.5V MIN will sink ≤40 mA in the low state. LOW equivalent crimp terminals. PFD SIGNAL 0-0.4 MAX T3 T2 T1 0.475 ±0.010 (12.07) DERATING CURVE (See Notes 9, 10) Output Power (Watts) 1.80 (45.72) MAX 1.00 110W ±0.005 (25.4) 20 CFM FORCED AIR COOLING 6-32 UNC 80W 0.050 ±0.020 1.55 ±0.005 3.35 ±0.015 (85.09) (4PL) (1.27) (39.37) PIN 1 Voltage Adjust Optional J2 Power Fail NATURAL Detect Circuit 55W 4.250 CONVECTION ±0.020 (Key = Pin 2) (107.95) COOLING 40W T1 T1 3.750 ±0.005 Pin 1 (95.25) PIN 1 L1 0.156 J1 11W C6 DIA. HOLE 11W MINIMUM LOAD REQUIRED AT 230VAC F1 (4PL) 0W 0°C 10°C 20°C 30°C 40°C 50°C 60°C 70°C 5A, 250 VAC 0.250 6.50 ±0.005 (165.1) ±0.010 (6.35) 7.00 ±0.020 (177.8) 0.250 ±0.010 PIN CONNECTIONS ALL DIMENSIONS IN INCHES (mm) (6.35) J1 –7601PJ –7602PJ –7604PJ SINGLES Mechanical Notes Pin 1 AC Ground AC Ground AC Ground AC Ground A Metallic or non-metallic stand-offs (maximum diameter 5.4 mm) can be Pin 2 AC Neutral AC Neutral AC Neutral AC Neutral used in all four mounting holes without effecting safety approval. B The ground pad of the mounting hole near J1, allows system grounding Pin 3 AC Line AC Line AC Line AC Line through a metal stand-off to the system chassis. C The heat sink is grounded, and allows system grounding by mechanical J2 connection to the system chassis. D The supply must be mechanically supported using the PCB mounting holes Pin 1 +5.1 V +5.1 V +5.1 V V out and may be additionally supported by the heatsink mounting holes. E It is always advisable to attach the power supply heat sink to another Pin 2 +5.1 V +5.1 V +5.1 V V out thermal dissipator (such as a chassis or finned heatsink etc). The resulting Pin 3 +5.1 V +5.1 V +5.1 V V decrease in heat sink mounted component temperatures will improve out power supply lifetime. Pin 4 Return Return Return Return F A standard L-bracket and cover is available for mounting which contains all screws, connectors and necessary mounting hardware. Two different kits Pin 5 Return Return Return Return are available, order part number ‘NFS110 COVER KIT’ or ‘NFS110C’. Pin 6 Return Return Return Return Pin 7 Return Return Return Return Pin 8 +12 V +12 V +15 V V out Pin 9 +12 V +12 V +15 V V out Pin 10 PFD PFD PFD N/C International Safety Standard Approvals Pin 11 –12 V –12 V –15 V N/C VDE0805/EN60950/IEC950/IEC1010 File No. 10401-3336-0049 Licence No. 108333 Pin 12 Removed for Key UL1950 File No. E136005 Pin 13 –5 V +24 V –5 V N/C CSA C22.2 No. 950 File No. LR41062C N/C = no connection. Datasheet © Artesyn Technologies® 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. File Name: nfs110.pdf Rev (02): 08 Nov 2005