<> <> General FA-M3 Basic Input/Output Modules Specifications GS 34M6G01-01E Contents F3XH04 High-Speed Input Module..............................................................................................3 F3XA08, F3XA16, F3XC08, F3XD08, F3XD16, F3XD32 and F3XD64 Input Modules .............................................................................................................................5 F3XD��-�N Input Module ...................................................................................................... 13 F3YD04, F3YA08, F3YC08, F3YC16, F3YD08, F3YD14, F3YD32 and F3YD64 Output Modules......................................................................................................................... 19 F3YD32-1H High-Speed Transistor Output Modules (sink type with short-circuit protector) ...... 29 F3YD32-1P, F3YD64-1P Transistor Output Modules (sink type with short-circuit protector)...... 31 F3YD32-1R, F3YD64-1R Transistor Output Modules (source type with short-circuit protector) ................................................................................... 35 F3WD64-�F Input/Output Modules........................................................................................... 39 F3WD64-�N Input/Output Modules .......................................................................................... 41 F3WD64-�P Input/Output Modules (sink type with short-circuit protector)................................ 43 TA40 Terminal Block Unit ......................................................................................................... 47 TA50-�N Connector Terminal Block Unit KM55-0�� Connector Terminal Block Cable ........................................................................... 49 TA60-0N Connector Terminal Block Unit................................................................................... 53 GS 34M6G01-01E ©Copyright Apr. 2009 10th Edition Apr. 2009 Yokogawa Electric Corporation Blank Page <> <> 3 General F3XH04 High-speed Input Module Specifications General The F3XH04 is a high-speed input module which incorporates the pulse-capture features of the FA-M3. - The pulse-capture features facilitate detection of pulse inputs with shorter on-time than the scan period, which allows the F3XH04 to carry out photo-micro switch input for high-speed sensing. - The interrupt mechanism ensures reliable interrupt processing using a short on-time pulse input. - The minimum pulse width is as short as 50 µs. - The four-independent input system permits connection from different signal systems. - The terminal block is provided with terminals for shielded cables. Components and Functions Specifications Item Specification Input type DC voltage 1 2 Number of inputs 4 Input LEDs : 3 4 Common system 4 independent inputs Indicates the on/off status of inputs. XH04-3N DC IN Isolation method Photocoupler isolation Rated input voltage 24 V DC + Operating voltage range 20.4 - 26.4 V DC IN1 Rated input current 11.2 mA/point (24 V DC) – Input impedance 2.1 KΩ Operating ON 16.0 V DC min. 7.2 mA min. SHIELD voltage/ current OFF 6.0 V DC max. 2.5 mA max. + Input 50 µs max. OFF → ON IN2 response – Terminal block : time ON → OFF 50 µs max. 10-point detachable terminal block. + Minimum input The terminal screws are M3.5 50 µs pulse width IN3 screws with square captive washers. Pulse – capture Selection By DIP switches. features* SHIELD Selection By DIP switches. Set for each point through Ladder + Interrupt Setting Diagram Support Program M3 features* IN4 Input hold The input signal is held for 512 µs after – time detection of an off-to-on transition. Current consumption 30 mA (5 V DC) External connection 10-point terminal block, M3.5 screw Weight 130 g *: The pulse-catch and interrupt features are not available at the same time. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 4 � External Connection Method Internal Circuit Diagram Terminal Block Type F3XH04-3N (High-speed input module) 2 Applicable conductor size 0.33-0.82 mm Wire connection method Solderless Solderless For 3.5 mm terminals terminal Crimping 1+ 0.8 N·m (8 kgf·cm, 6.9lbf·in) torque Solderless terminal Example: + Bus Applicable Japan Solderless Terminal Mfg. - solderless Co., Ltd.:V1.25-M3 interface Nippon Tanshi Co., Ltd.: terminal RAV1.25-3.5 1- Operating Environment There is no restriction on the type of CPU modules that can be used with this module. External Connection Diagram F3XH04-3N (High-speed input module) Model and Suffix Codes Suffix Style Option Model Description Code Code Code 1+ 1 High-speed inputs with F3XH04 -3N . . . . . . . . . . pulse-capture feature, 1– 2 24 V DC, 4 points SHIELD 3 2+ 4 + 2– 5 – 3+ 6 3– 7 SHIELD 8 4+ 9 4– 10 External Dimensions Unit: mm All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Internal bus <> <> 5 General F3XA08, F3XA16, F3XC08, F3XD08, F3XD16, F3XD32 and F3XD64 Specifications Input Modules Note: F3XA16-1N is not UL-crertified. General The input modules for the FA-M3 are listed below. Select the most appropriate modules according to your applications. F3XA08-1N AC input module F3XA08-2N AC input module F3XA16-1N AC input module F3XC08-0C No voltage contact input module F3XC08-0N No voltage contact input module F3XD08-6F DC input module F3XD16-3F DC input module F3XD16-4F DC input module F3XD32-3F DC input module F3XD32-4F DC input module F3XD32-5F DC input module F3XD64-3F DC input module F3XD64-4F DC input module F3XD64-6M DC input module F3XD16-3H DC input module Components and Functions The input modules are divided into terminal block and connector types as shown below. � Terminal Blocks � Connector type • 10-point • 18-point terminal block terminal block 1 5 1 5 9 13 1 5 9 13 17 21 25 29 2 6 2 6 10 14 2 6 10 14 18 22 26 30 Input indication LED Input LEDs 3 7 3 7 11 15 3 7 11 15 19 23 27 31 4 8 4 8 12 16 4 8 12 16 20 24 28 32 Indicates the on/off Indicates on or off status AC IN DC IN DC IN of each input. status of the inputs. DISPLAY 12 1 1 Display selector switch 2 Selects the input LEDs. Not 2 3 available for 32-point modules. 4 3 5 6 4 7 8 Terminal block 5 10- or 18-point COM1 detachable terminal 9 6 block. The terminal 10 One or two 40-pin connectors screws are M3.5 11 Only one connector is available 7 screws with captive 12 for 32-point inputs and the square washers. 13 F3XD64-6M. 8 14 15 16 COM COM2 Display selector LED Indication switch position 1 Indicates the on/off status of inputs 1 to 32. 2 Indicates the on/off status of inputs 33 to 64. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 6 Specifications Operating Voltage/Current Number Isolation Rated Input Operating Voltage Model Input Type Rated Input Voltage of Inputs Method Current Range ON OFF 100 - 120 V AC 5.4 - 6.5 mA/point 85 - 132 V AC 80 V AC min. 40 V AC max. F3XA08-1N 50/60 Hz 100-120V AC,60Hz 50/60Hz 5 mA min. 1 mA max. 8 200 - 240 V AC 5.1 - 6.1 mA/point 170 - 264 V AC 160 V AC min. 70 V AC max. F3XA08-2N AC voltage 50/60 Hz 200-240 V AC,60Hz 50/60Hz 4 mA min. 1 mA max. 100 - 120 V AC 5.4 - 6.5 mA/point 85 - 132 V AC 80 V AC min. 40 V AC max. F3XA16-1N 16 50/60 Hz 100-120 V AC,60Hz 50/60Hz 5 mA min. 1 mA max. 4.1 mA/point (12V DC) 8.0 V DC min. 3.4 V DC max. F3XD08-6F 8 12 - 24 V DC 10.2 - 26.4 V DC 8.5 mA/point 2.6 mA min. 1.0 mA max. (24V DC) 4.1 mA/point 16.0 V DC min. 5.8 V DC max. F3XD16-3F 24 V DC 20.4 - 26.4 V DC 24 V DC 3.2 mA min. 0.9 mA max. 16 4.1 mA/point} 8.0 V DC min. 3.4 V DC max. F3XD16-4F 12 V DC 10.2 - 13.2 V DC 12 V DC 2.6 mA min. 1.0 mA max. 4.1 mA/point 16.0 V DC min. 5.8 V DC max. DC voltage F3XD32-3F 24 V DC 20.4 - 26.4 V DC 24 V DC 3.2 mA min. 0.9 mA max. (sink/source) 4.1 mA/point 8.0 V DC min. 3.4 V DC max. F3XD32-4F 32 12 V DC 10.2 - 13.2 V DC 12 V DC 2.6 mA min. 1.0 mA max. 4.0 mA/point 3.5 V DC min. 1.0 V DC max. F3XD32-5F 5 V DC 4.5 - 5.5 V DC 5 V DC 2.0 mA min. 0.2 mA max. 4.1 mA/point 16.0 V DC min. 5.8 V DC max. F3XD64-3F 24 V DC 20.4 - 26.4 V DC 24 V DC 3.2 mA min. 0.9 mA max. 4.1 mA/point 8.0 V DC min. 3.4 V DC max. 64 F3XD64-4F 12 V DC 10.2 - 13.2 V DC 12 V DC 2.6 mA min. 1.0 mA max. 3.9 mA (12 V DC) 8.0 V DC min. 3.4 V DC max. F3XD64-6M Matrix scan 12 - 24 V DC 10.2 - 26.4 V DC 8.2 mA (24 V DC) 2.6 mA min. 1.0 mA max. DC voltage 4. 7 mA/point 16 V DC min. 5.8 V DC max. F3XD16-3H 16 24 V DC 20.4 - 26.4 V DC (+common) 24 V DC 3.2 mA min. 0.9 mA max. Number Model Input Type Isolation Method Contact Ratings ON Resistance OFF Resistance of Inputs F3XC08-0C No-voltage Transformer 5 V DC min. 8 200 Ω max. 100 kΩmin. contact isolation 20 mA max. F3XC08-0N All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Photocoupler isolation <> <> 7 Maximum ratio Input response External Points/ Current of inputs *2 Weight Interrupt Connection Common Consumption turned on OFFJON ONJOFF simultaneously 10-point 40 mA terminal block 130 g (5 V DC) Selectable from Selectable from M3.5 screw 15 ms max. or 25 ms max. or 30 ms 40 ms 18-point 65 mA terminal block 180 g (5 V DC) M3.5 screw 10-point 40 mA terminal block 130 g (5 V DC) Can be specified for M3.5 screw 100% each input point. 18-point 8 points/ Input sampling Input sampling 65 mA terminal block 160 g common period can be period can be (5 V DC) M3.5 screw specified within specified within 0-16 ms in 0-16 ms in *1 *1 5 levels 5 levels One 40-pin 75 mA 120 g connector (5 V DC) Input sampling Input sampling period can be period can be Two 40-pin 100 mA 60% 160 g specified within specified within connectors (5 V DC) *1 *1 None 0-1 ms in 4 levels 0-1 ms in 4 levels. One 40-pin 110 mA – 16 ms max. 16 ms max. 8 x 8 matrix 130 g connector (5 V DC) Input sampling period Input sampling period can be specified can be specified 8 points/ Can be specified 65 mA 100% 160 g within 0-16 ms in 5 within 0-16 ms in 5 common for each input point. (5 V DC) *1 *1 levels levels Maximum ratio Input response External Points/ Current of inputs *2 Weight Interrupt Connection Common Consumption turned on OFFJON ONJOFF simultaneously Separate 170 g commons Selectable from 2.0 Selectable from 2.0 10-point terminal Can be specified for 100% 75 mA ms max. or 17 ms ms max. or 17 ms block M3.5 screw each input point. 8 points/ 140 g common Note: See external dimensions for dimensions of the modules. *1: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or F3SP67 is used. For other CPU modules, the specification is the same as the F3XD††-†N. The actual response time can be obtained by adding the following values: For F3XD††-†F: 100 µs (OFF J ON) 300 µs (ON JOFF) For F3XD16-3H: 10 µs *2: If the input interrupt is to be used with the F3XD††-†F, set the input sampling period to at least 62.5 µs. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 8 Internal Circuit Diagram F3XA08-1N F3XC08-0C F3XA08-2N +5V F3XA16-1N 1 1 Bus c1 interface COM Bus 8 interface 9 COM Clock generator F3XD08-6F F3XC08-0N F3XD16-3F +5V F3XD16-4F 1 1 Bus interface – + Bus + – 8 interface 8 9 COM 9 COM Clock generator F3XD16-3H F3XD32-3F F3XD32-4F F3XD32-5F 1 9 COM Bus 8 interface 8 Bus 9 COM interface 1 F3XD64-3F F3XD64-6M F3XD64-4F 12V/24VDC OUT8 • • • 9 COM • Bus • • • interface 8 OUT2 Bus OUT1 interface 1 1 DATA8 DATA7 • • Display selector • 2 1 DATA1 2 Display selector 1 : CN1 2 : CN2 All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 ~ ~ ~ ~ Internal bus Internal bus Internal bus Internal bus ~ Input interface Internal bus Internal bus Internal bus Internal bus + – – + + – – + + – <> <> 9 External Connection Diagram F3XA08-1N F3XC08-0C F3XC08-0N F3XA08-2N 1 1 1 1 1 c1 2 2 1 2 2 2 3 3 3 2 c2 3 4 4 4 3 3 5 4 5 c3 5 4 6 5 6 4 6 7 5 c4 6 7 8 7 6 5 7 9 8 8 c5 7 10 8 COM 6 9 8 11 c6 COM 10 12 9 7 13 10 c7 14 Note: Viewed from the front of the module. 8 15 c8 Note: Viewed from the front of the module. 16 17 18 Note: Viewed from the front of the module. F3XA16-1N F3XD08-6F 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 5 4 -+ 5 5 6 6 5 +- 7 6 7 6 8 8 7 COM1 7 9 8 9 8 10 10 COM 11 9 11 12 12 10 13 13 14 14 Note: Viewed from the front of the module. 15 15 16 16 17 COM2 18 Note: Viewed from the front of the module. F3XD16-3F F3XD16-3H F3XD32-3F F3XD16-4F F3XD32-4F 1 1 F3XD32-5F 2 1 2 1 3 2 3 2 4 BA 3 4 - 3 5 20 20 4 5 - + + 4 6 19 19 5 6 COM4 COM2 + - 5 7 18 18 6 7 32 16 6 8 7 17 17 8 31 15 7 COM1 8 16 16 9 30 14 8 9 COM1 15 15 10 9 29 13 10 - + - + 9 14 14 11 28 12 10 11 - + - 10 + 13 13 12 11 12 27 11 11 12 12 - 13 26 10 12 13 12 11 11 14 - + + 13 25 9 14 13 15 10 10 + - COM3 COM1 15 14 14 9 9 16 15 24 8 16 15 17 8 8 COM2 23 7 16 16 18 7 7 17 22 6 COM2 6 6 18 21 5 + - - + 5 5 20 4 - Note: Viewed from the front of the module. - + + Note: Viewed from the front of the module. 4 4 19 3 3 3 18 2 2 2 17 1 1 1 Note: Viewed from the front of the module. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 10 F3XD64-3F F3XD64-4F BA BA CN1 CN2 20 20 20 20 19 19 19 19 COM4 COM2 COM8 COM6 18 18 18 18 32 16 64 48 17 17 17 17 31 15 63 47 16 16 16 16 30 14 62 46 15 15 15 15 29 13 61 45 + - - + +-+ - 14 14 14 14 28 12 60 44 - + + - - + + - 13 13 13 13 27 11 59 43 12 12 12 12 26 10 58 42 11 11 11 11 25 9 57 41 10 10 10 10 COM3 COM1 COM7 COM5 9 9 9 9 24 8 56 40 8 8 8 8 23 7 55 39 7 7 7 7 22 6 54 38 6 6 6 6 21 5 53 37 + - + + - - + - 5 5 5 5 20 4 52 36 - - + + + - - + 4 4 4 4 19 3 51 35 3 3 3 3 18 2 50 34 2 2 2 2 17 1 49 33 1 1 1 1 FA020528.VSD Note: Viewed from the front of the module. F3XD64-6M Note: Viewed from the front of the module. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 11 � Terminal Arrangement � External Connection Method Terminal 10-point 18-point Connector Type Connector Connector Block Type terminal block terminal block Flat cable, 32-point 64-point 2 Applicable 2 0.26 mm 0.08 - 1.27 mm connector connector 0.33 - 0.82 mm 2 max. 0.20 mm pitch, conductor size BA BA BA 2 0.08 mm 12 20 20 20 20 20 20 Wire connection 1 1 Solderless Soldered Solderless Solderless 19 19 19 19 19 19 method 2 18 18 18 18 18 18 Rated wire 2 3 75°C min. 17 17 17 17 17 17 temperature 4 16 16 16 16 16 16 Copper Wire Material 3 5 15 15 15 15 15 15 Solderless For 3.5 mm 6 — 14 14 14 14 14 14 terminals terminal 4 7 13 13 13 13 13 13 0.8 N·m Crimping 8 {8 kgf·cm, — 12 12 12 12 12 12 torque 6.9 lbf·in} 5 9 11 11 11 11 11 11 Example: 10 10 10 10 10 10 10 Japan 6 11 Solderless 9 9 9 9 9 9 12 Applicable Terminal 8 8 8 8 8 8 solderless Mfg Co., Ltd.: — 7 13 7 7 7 7 7 7 V1.25-M3 terminal 14 Nippon Tanshi 6 6 6 6 6 6 8 15 Co., Ltd.: 5 5 5 5 5 5 RAV1.25-3.5 16 4 4 4 4 4 4 9 17 3 3 3 3 3 3 � Applicable External Connectors 18 2 2 2 2 2 2 Connection Method Applicable Connector 10 1 1 1 1 1 1 Fujitsu : FCN-361J040-AU connector Soldered type FCN-360C040-B connector cover M3.5 Fujitsu : FCN-363J040 housing M3.5 Solderless type FCN-363J-AU contact FCN-360C040-B connector cover 8.2 mm 7.1 mm Fujitsu : Solderless type FCN-367J040-AU/F 8.2 mm 6.4 mm 7.1 mm Operating Environment There is no restriction on the type of CPU modules that can be used with this module. Model and Suffix Codes Model Suffix code Style code Option code Description 100-120 V AC input, 8 points F3XA08 -1N . . . . . . . . . . F3XA08 -2N . . . . . . . . . . 200-240 V AC input, 8 points F3XA16 -1N . . . . . . . . . . 100-120 V AC input, 16 points No-voltage contact, 8 points (with separate commons) F3XC08 -0C . . . . . . . . . . F3XC08 -0N . . . . . . . . . . No-voltage contact, 8 points F3XD08 -6F . . . . . . . . . . DC input sink/source, 12-24 V DC, 8 points DC input sink/source, 24 V DC, 16 points F3XD16 -3F . . . . . . . . . . DC input sink/source, 12 V DC, 16 points F3XD16 -4F . . . . . . . . . . F3XD32 -3F . . . . . . . . . . DC input sink/source, 24 V DC, 32 points* F3XD32 -4F . . . . . . . . . . DC input sink/source, 12 V DC, 32 points* DC input sink/source, 5 V DC, 32 points* F3XD32 -5F . . . . . . . . . . F3XD64 -3F . . . . . . . . . . DC input sink/source, 24 V DC, 64 points* F3XD64 -4F . . . . . . . . . . DC input sink/source, 12 V DC, 64 points* DC input matrix scan 12-24 V DC, 64 points* F3XD64 -6M . . . . . . . . . . F3XD16 -3H . . . . . . . . . . DC input (sink, +common), 24 V DC, 16 points (Quick response type) *: See the section on spare parts in FA-M3 Range-free Multi-controller (GS 34M6A01-01E) for information on connectors. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Solderless terminal <> <> 12 External Dimensions F3XA08, F3XC08, F3XD08 F3XA16 Unit: mm F3XD16 F3XD32 F3XD64-3F, F3XD64-4F F3XD64-6M All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 13 General F3XD��-�N Input Module Specifications General The F3XD��-�N input modules for the FA-M3 are listed below. Select the most appropriate modules according to your applications. F3XD08-6N DC input module F3XD16-3N DC input module F3XD16-4N DC input module F3XD32-3N DC input module F3XD32-4N DC input module F3XD32-5N DC input module F3XD64-3N DC input module F3XD64-4N DC input module Components and Functions The input modules are divided into terminal block and connector types as given below. � Terminal block � Connector • 10-point • 18-point terminal block terminal block 1 5 1 5 9 13 1 5 9 13 17212529 2 6 2 6 10 14 2 6 10 14 18222630 Input LEDs Input LEDs 3 7 3 7 11 15 3 7 11 15 19232731 4 8 4 8 12 16 4 8 12 16 20242832 Indicates the on/off Indicates the on/off DC IN DC IN DC IN status of the inputs. status of the inputs. DISPLAY 12 1 1 Display selector switch 2 Selects the input LEDs. 2 3 Not available for 32- 4 point modules. 3 5 6 4 7 8 Terminal block 5 One or two 40-pin connectors COM1 10- or 18-point Only one connector is 9 detachable terminal 6 available for 32-point 10 block. The terminal inputs. screws are M3.5 screws 11 7 with captive square 12 washers. 13 8 14 15 COM 16 COM2 DisplaySelector LED Indication Switch Position 1 Indicates the on/off status of inputs 1 to 32. 2 Indicates the on/off status of inputs 33 to 64. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 ~ ~ ~ <> <> 14 Specifications Operating Voltage/Current Input Number Isolation Rated Input Operating Model Rated Input Current Type of Inputs Method Voltage Voltage Range ON OFF 4.1 mA/point (12V DC) 8.0 V DC min. 3.4 V DC max. F3XD08-6N 8 12-24V DC 10.2 - 26.4 V DC 8.5 mA/point (24V DC) 2.6 mA min. 1.0 mA max. 4.1 mA/point 16.0 V DC min. 5.8 V DC max. F3XD16-3N 24 V DC 20.4 - 26.4 V DC 24 V DC 3.2 mA min. 0.9 mA max. 16 4.1 mA/point 8.0 V DC min. 3.4 V DC max. F3XD16-4N 12 V DC 10.2 - 13.2 V DC 12 V DC 2.6 mA min. 1.0 mA max. 4.1 mA/point 16.0 V DC min. 5.8 V DC max. 24 V DC 20.4 - 26.4 V DC F3XD32-3N 24 V DC 3.2 mA min. 0.9 mA max. 4.1 mA/point 8.0 V DC min. 3.4 V DC max. 32 F3XD32-4N 12 V DC 10.2 - 13.2 V DC 12 V DC 2.6 mA min. 1.0 mA max. 4.0 mA/point 3.5 V DC min. 1.0 V DC max. F3XD32-5N 5 V DC 4.5 - 5.5 V DC 5 V DC 2.0 mA min. 0.2 mA max. 4.1 mA/point 16.0 V DC min. 5.8 V DC max. F3XD64-3N 24 V DC 20.4 - 26.4 V DC 24 V DC 3.2 mA min. 0.9 mA max. 64 4.1 mA/point 8.0 V DC min. 3.4 V DC max. F3XD64-4N 12 V DC 10.2 - 13.2 V DC 12 V DC 2.6 mA min. 1.0 mA max. Note: See external dimensions for dimensions of the modules. Internal Circuit Diagram F3XD08-6N DC input module F3XD32-3N DC input module F3XD16-3N DC input module F3XD32-4N DC input module F3XD16-4N DC input module F3XD32-5N DC input module 1 9 COM 8 – + + – Bus Bus + – interface 8 – + interface 9 COM 1 F3XD64-3N DC input module F3XD64-4N DC input module 9 COM 8 + – Bus – + interface 1 1 Display selector 2 All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 DC voltage (sink/source) Photocoupler isolation Internal bus Internal bus Internal bus <> <> 15 Input response External *2 Current Common line type Interrupt Weight Connection Consumption OFFJON ONJOFF 10-point terminal 40 mA 130 g block M3.5 screw (5 V DC) 18-point 65 mA terminal block 160 g (5 V DC) Selectable from Selectable from M3.5 screw Can be specified for 2.0 ms max. or 3.5 ms max. or each input point. 17 ms 18.5 ms 8 points/common One 40-pin 75 mA 120 g connector (5 V DC) Two 40-pin 100 mA 1.0 ms max. 2.5 ms max. None 160 g connectors (5 V DC) External Connection Diagram F3XD16-3N DC input module F3XD16-4N DC input module F3XD08-6N DC input module 1 1 1 1 2 2 2 2 3 3 3 4 3 – + 4 5 4 5 4 + – – + 6 5 6 5 7 + – 7 6 8 6 8 7 COM1 9 7 9 8 10 8 10 11 COM 11 9 12 12 – + 13 10 Note : Viewed from the front of the module. 13 14 + – 14 15 15 16 16 17 F3XD32-3N DC input module COM2 18 F3XD32-4N DC input module F3XD32-5N DC input module Note : Viewed from the front of the module. BA 20 20 19 19 COM4 COM2 18 18 32 16 17 17 31 15 16 16 30 14 15 15 29 13 – – + + 14 14 28 12 – – + + 13 13 27 11 12 12 26 10 11 11 25 9 10 10 COM3 COM1 9 9 24 8 8 8 23 7 7 7 22 6 6 6 21 5 – + – + 5 5 20 4 – – + + 4 4 19 3 3 3 18 2 2 2 17 1 1 1 Note : Viewed from the front of the module. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 16 F3XD64-3N DC input module F3XD64-4N DC input module BA BA CN1 20 20 CN2 20 20 19 19 19 19 COM4 COM2 COM8 COM6 18 18 18 18 32 16 64 48 17 17 17 17 31 15 63 47 16 16 16 16 30 14 62 46 15 15 15 15 29 13 61 45 – + – + – – + + 14 14 14 14 28 12 60 44 – – + + – + + – 13 13 13 13 27 11 59 43 12 12 12 12 26 10 58 42 11 11 11 11 25 9 57 41 10 10 10 10 COM3 COM1 COM7 COM5 9 9 9 9 24 8 56 40 8 8 8 8 23 7 55 39 7 7 7 7 22 6 54 38 6 6 6 6 21 5 53 37 + – – + – + + – 5 5 5 5 – 20 4 52 36 – – + + + – + 4 4 4 4 19 3 51 35 3 3 3 3 18 2 50 34 2 2 2 2 17 1 49 33 1 1 1 1 Note : Viewed from the front of the module. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 17 � Terminal Arrangement � External Connection Method Terminal 10-point 18-point Connector Type Connector Connector Block Type terminal block terminal block Flat cable, 32-point 64-point 2 Applicable 2 0.26 mm 0.08 - 1.27 mm connector connector 0.33 - 0.82 mm 2 max. 0.20 mm pitch, conductor size BA BA BA 2 0.08 mm 12 20 20 20 20 20 20 Wire connection 1 1 Solderless Soldered Solderless Solderless 19 19 19 19 19 19 method 2 18 18 18 18 18 18 Rated wire 2 3 75°C min. 17 17 17 17 17 17 temperature 4 16 16 16 16 16 16 Copper Wire Material 3 5 15 15 15 15 15 15 Solderless For 3.5 mm 6 — 14 14 14 14 14 14 terminals terminal 4 7 13 13 13 13 13 13 0.8 N·m Crimping 8 {8 kgf·cm, — 12 12 12 12 12 12 torque 6.9 lbf·in} 5 9 11 11 11 11 11 11 Example: 10 10 10 10 10 10 10 Japan 6 11 Solderless 9 9 9 9 9 9 12 Applicable Terminal 8 8 8 8 8 8 solderless Mfg Co., Ltd.: — 7 13 7 7 7 7 7 7 V1.25-M3 terminal 14 Nippon Tanshi 6 6 6 6 6 6 8 15 Co., Ltd.: 5 5 5 5 5 5 RAV1.25-3.5 16 4 4 4 4 4 4 9 17 3 3 3 3 3 3 � Applicable External Connectors 18 2 2 2 2 2 2 Connection Method Applicable Connector 10 1 1 1 1 1 1 Fujitsu : FCN-361J040-AU connector Soldered type FCN-360C040-B connector cover M3.5 Fujitsu : FCN-363J040 housing M3.5 Solderless type FCN-363J-AU contact FCN-360C040-B connector cover 8.2 mm 7.1 mm Fujitsu : Solderless type FCN-367J040-AU/F 8.2 mm 6.4 mm 7.1 mm Operating Environment There is no restriction on the type of CPU modules that can be used with this module. Model and Suffix Codes Model Suffix code Style code Option code Description F3XD08 -6N . . . . . . . . . . DC input sink/source, 12-24 V DC, 8 points DC input sink/source, 24 V DC, 16 points F3XD16 -3N . . . . . . . . . . DC input sink/source, 12 V DC, 16 points F3XD16 -4N . . . . . . . . . . F3XD32 -3N . . . . . . . . . . DC input sink/source, 24 V DC, 32 points* F3XD32 -4N . . . . . . . . . . DC input sink/source, 12 V DC, 32 points* DC input sink/source, 5 V DC, 32 points* F3XD32 -5N . . . . . . . . . . F3XD64 -3N . . . . . . . . . . DC input sink/source, 24 V DC, 64 points* F3XD64 -4N . . . . . . . . . . DC input sink/source, 12 V DC, 64 points* *: See the section on spare parts in the FA-M3 Range-free Multi-controller (GS 34M6A01-01E) for information on connectors. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Solderless terminal <> <> 18 External Dimensions F3XD08 F3XD16 Unit: mm F3XD32 F3XD64-3N, F3XD64-4N All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 19 F3YD04, F3YA08, F3YC08, General F3YC16, F3YD08, F3YD14, Specifications F3YD32 and F3YD64 Output Modules General Note: The F3YA08-2N module is not UL-certified. The output modules for the FA-M3 are listed below. Select the most appropriate modules according to your applications. F3YD04-7N Transistor output module F3YA08-2N TRIAC output module F3YC08-0C Relay output module F3YC08-0N Relay output module F3YC16-0N Relay output module F3YD08-6A Transistor output module F3YD08-6B Transistor output module F3YD08-7A Transistor output module F3YD14-5A Transistor output module F3YD14-5B Transistor output module F3YD32-1A Transistor output module F3YD32-1B Transistor output module F3YD32-1T TTL output module F3YD64-1A Transistor output module F3YD64-1F Transistor output module F3YD64-1M Transistor output module Components and Functions The output modules are divided into terminal block and connector types as given below. � Terminal block • 10-point • 18-point terminal block terminal block 1 5 1 5 9 13 1 5 9 13 17 21 25 29 2 6 2 6 10 14 2 6 10 14 18 22 26 30 Output LEDs Output LEDs 3 7 3 7 11 15 19 23 27 31 3 7 11 4 8 Indicates the on/off 4 8 12 16 20 24 28 32 4 8 12 Indicates the on/off status of YD�8-�N �� OUT status of the outputs. Y��� -�� �� OUT YD��-1� DC OUT the outputs. DISPLAY L 12 1 L Display selector switch 1 L Selects the output LEDs. Not 2 L available for 32-point modules. 3 L L L 4 2 L 5 L 6 L 7 L 8 L L Terminal block 3 One or two 40-pin connectors 10- or 18-point COM 1 Only one connector is available detachable terminal L for 32-point inputs and the block. The terminal 9 L F3YD64-1M. screws are M3.5 L L 10 4 L screws with captive 11 L square washers. 12 Display Selector L LED Indication 13 Switch Position L 14 Indicates the on/off status COM 2 1 of outputs 1 to 32. Indicates the on/off status 2 of outputs 33 to 64. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 20 Specifications Response Time Number of Points/ Isolation Rated Load Maximum load Model Output Type Outputs Common Method Voltage current OFFJON ONJOFF All points F3YD04-7N Transistor contact 4 24 V DC 2 A/point 5 ms max. 3 ms max. independent Photocoupler 1 A/point (0 - 40°C) Isolation 8 points/ 1/2 cycle F3Y A08-2N TRIAC contact 100－240 V AC 0.7 A/point (40 - 55°C) 1 ms max. common +1 ms max. 3 A/common All points DC AC *4 F3YC08-0C 2 A/point independent Mechanical Relay contact 10 ms max. 10 ms max. Isolation 5－ 100－ 2 A/point *4 F3YC08-0N 24 V 240 V 8 8 A/common Transistor contact F3YD08-6 A (sink type) 8 points/ 1 A/point common 4 A/common Transistor contact F3YD08-6B (source type) Photocoupler Transistor contact 2 A/point 12－24 V DC 1 ms max. 1 ms max. F3YD08-7A Isolation (sink type) 8 A/common Transistor contact 8 points/ F3YD14-5 A (sink type) common 0.5 A/point 14 6 points/ 2 A/common Transistor contact F3YD14-5B common (source type) DC AC Mechanical 2 A/point *4 F3YC16-0N Relay contact 16 10 ms max. 10 ms max. 5－ 100－ Isolation 8 A/common 24 V 240 V Transistor contact F3YD32-1 A (sink type) 0.1 A/point 12－24 V DC 0.5 A/common Transistor contact 32 8 points/ F3YD32-1B (source type) common Transistor contact 16 mA/point F3YD32-1T 5 V DC 1 ms max. 1 ms max. (TTL output) 128 mA/common Photocoupler Isolation F3YD64-1 A Transistor contact 0.1 A/point 24 V DC (sink type) 0.4 A/common *1 64 F3YD64-1F Transistor contact F3YD64-1M 8 x 8 matrix 12－24 V DC 0.1 A 16 ms max. 16 ms max. ( matrix scan) Note: See external dimensions for dimensions of the modules. *1: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or F3SP67 is used, the output for CPU fatal errors can be set either to HOLD or RESET. *2 When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or F3SP67 is used, all points can be specified in 16-point units. *3 For details on the module behavior when the CPU fails, see the Severity of Failures and LED Display” in the FA-M3 Range-free Multi-controller (GS 34M6A01-01E). *4 The relays in the relay output modules are not of hermetically sealed type. Dust or corrosive gases in the installation environment will adversely affect the service life of the relays. Relays that are switched on and off in an atmosphere containing silicone gases from silicone-based materials may suffer from poor electrical contact due to SiO (silicon dioxide) formed and deposited on the surfaces of their contacts. Risks of bad contact due to silicon 2 gases are especially high under load conditions below 24 VDC and 500 mA. In such environments, we recommend the use of transistor output modules or other modules employing semiconductor elements instead. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 21 Off-time CPU Error Surge Current External Power External *3 Life ON voltage Leakage Output Weight Protector Consumption Supply Connection Current HOLD/RESET 0.5 V DC 0.1 mA 85 mA Zener diode 140 g max. max. (5 V DC) 10 -point terminal ― block M3.5 screw 1.5 V AC 3 mA CR absorber 130 mA 150 g max. max. Varistor (5 V DC) Not required Mechanical Electrical 18 -point terminal 180 g block M3.5 screw 205 mA ― ― None 20, 000, 000 100, 000 (5 V DC) operations or operations or 160 g more more 10 -point terminal block M3.5 screw 60 mA 12－24 V DC 130 g (5 V DC) 10 mA When a sequence 0.5 V DC 0.1 mA CPU is used: ― Active clamp max. max. Initial value: RESET 120 mA 12－24 V DC All module 160 g (5 V DC) 20 mA outputs can be *2 set collectively . 18 -point terminal block M3.5 screw When a BASIC Mechanical Electrical CPU is used: 380 mA 20, 000, 000 100, 000 No setting ― ― None Not required 220 g (5 V DC) operations or operations or function; more more Always set to HOLD. 0.5 V DC 0.1 mA 210 mA 12－24 V DC 100 g max. max. (5 V DC) 115 mA One 40-pin connector 210 mA 5 V DC ― ― 110 g ― Zener diode (5 V DC) 60 mA 0.5 V DC 275 mA 24 V DC Two 40-pin 160 g max. (5 V DC) 150 mA connectors 0.1 mA max. 1.5 V DC 125 mA 12－24 V DC One 40-pin 110 g max. (5 V DC) 40 mA connector All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 22 Internal Circuit Diagram F3YD04-7N Transistor output module F3YA08-2N TRIAC output module 1 L Bus 1P L interface + Bus – interface 8 1N L 9 4N COM F3YD08-7A Transistor output module F3YD08-6B Transistor output module F3YD08-6A Transistor output module F3YD14-5B Transistor output module F3YD14-5A Transistor output module Bus 1 Bus 1 L L interface interface + – – + 8 8 L L 9 COM 9 COM 10 10 F3YC08-0N Relay output module F3YC08-0C Relay output module F3YC16-0N Relay output module 5 V line 5 V line 1 1 L L c1 Bus Bus interface interface 8 L 9 COM F3YD32-1B Transistor output module F3YD32-1A Transistor output module 10 10 9 COM 9 COM 8 Bus Bus L 8 L interface interface + – – + 1 1 L L All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Internal bus Internal bus Internal bus Internal bus ~ ~ ~ Internal bus Internal bus Internal bus Internal bus ~ ~ ~ ~ <> <> 23 F3YD64-1A Transistor output module F3YD32-1T TTL output module F3YD64-1F Transistor output module 10 10 9 COM 9 COM 8 8 Bus L Bus L interface – interface + 1 – + Display selector 1 2 1 L L F3YD64-1M Transistor output module 12 / 24V DC OUT 8 • • • • OUT 2 Bus interface OUT 1 DATA 8 DATA 7 • • • DATA 1 1 2 Display selector All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Internal bus Internal bus Output interface ~ Internal bus ~ <> <> 24 External Connection Diagram F3YD04-7N Transistor output module F3YA08-2N TRIAC output module – + 1P 1P L 1 1 1 L 1 – + 1N 1N L 2 – + 2 2 L 2 2P 2P L 3 3 3 L 3 + – 2N 2N 4 L – + 4 4 L 4 3P 3P 5 L 5 5 L 5 + – 3N 3N 6 L – + 6 6 L 6 4P 4P 7 L 7 7 L 7 – + 4N 4N 8 L 8 8 L 8 COM 9 9 9 10 10 10 Note: Viewed from the front of the module. Note: Viewed from the front of the module. F3YC08-0C Relay output module F3YC08-0N Relay output module F3YC16-0N Relay output module 1 1 1 L 1 1 L L 1 2 c1 L 2 2 2 3 L 2 2 L 3 3 L 3 4 L 3 c2 L 4 4 5 4 L 5 3 5 L 4 L 6 L c3 5 6 6 L 5 7 4 L 7 7 6 L 8 L 6 c4 L 8 8 COM1 7 9 5 L 7 9 L 9 8 L c5 10 10 L 8 10 L 11 6 COM 11 L 11 9 L 12 c6 12 12 10 L 13 7 13 L 13 L 14 c7 14 14 Note: Viewed from the front of the module. L 15 8 15 L 15 L 16 c8 16 16 L 17 17 COM2 18 18 Note: Viewed from the front of the module. Note: Viewed from the front of the  module. F3YD08-6A Transistor output module F3YD08-6B Transistor output module F3YD08-7A Transistor output module 1 1 L 1 L 1 2 2 L 2 L 2 3 3 L 3 L 3 4 4 L 4 L 4 5 5 L 5 L 5 – + 6 6 L 6 L 6 + – 7 7 L 7 L 7 8 8 L 8 L 8 COM COM 9 9 12–24V 0V 10 10 Note: Viewed from the front of the module. Note: Viewed from the front of the module. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 25 F3YD14-5A Transistor output module F3YD14-5B Transistor output module 1 1 L 1 L 1 2 2 L 2 L 2 3 3 3 3 L L 4 4 – L L + 4 4 5 5 + L 5 L 5 – 6 6 L L 6 6 7 7 L 7 L 7 8 8 L 8 L 8 COM1 COM1 9 9 12–24V 0V 10 10 9 9 L 11 L 11 10 10 L 12 L 12 11 11 13 – 13 L L + 12 12 L 14 L 14 + 13 13 – L 15 L 15 14 14 L L 16 16 COM2 COM2 17 17 12–24V 0V 18 18 Note: Viewed from the front of the module. Note: Viewed from the front of the module. F3YD32-1A Transistor output module F3YD32-1B Transistor output module BA BA 12—24V 12—24V 0V 0V 20 20 20 20 COM4 COM4 COM2 COM2 19 19 19 19 32 32 16 16 L 18 18 L L 18 18 L 31 31 15 15 L 17 17 L L 17 17 L 30 30 14 14 L 16 16 L L 16 16 L 29 13 29 13 L 15 15 L L 15 15 L 28 12 28 12 L 14 14 L L 14 14 L 27 11 27 11 L 13 13 L L 13 13 L 26 10 26 10 L 12 12 L L 12 12 L 25 9 25 9 L 11 11 L L 11 11 L 12—24V 12—24V 0V 0V 10 10 10 10 COM3 COM1 COM3 COM1 9 9 9 9 24 8 24 8 L 8 8 L 8 8 23 7 23 7 L 7 7 L 7 7 22 6 22 6 6 6 6 6 L L 21 5 21 5 5 5 5 5 L L 20 4 20 4 L 4 4 L 4 4 19 3 19 3 L 3 3 L 3 3 18 2 18 2 L 2 2 L 2 2 17 1 17 1 L 1 1 L 1 1 Note: Viewed from the front of the module. Note: Viewed from the front of the module. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 + + + + + + + + <> <> 26 F3YD32-1T TTL output module F3YD64-1A Transistor output module F3YD64-1F Transistor output module CN1 CN2 BA BA BA +24V +24V +24V +24V 5V 5V 20 20 20 20 20 20 COM4 COM2 COM8 COM6 COM4 COM2 19 19 19 19 19 19 32 16 64 48 32 16 L 18 18 L L 18 18 L L 18 18 L 31 15 63 47 31 15 L 17 17 L L 17 17 L L 17 17 L 30 14 62 46 30 14 L 16 16 L L 16 16 L L 16 16 L 29 13 61 45 29 13 L 15 15 L L 15 15 L L 15 15 L + + + 28 12 60 44 28 12 L 14 14 L L 14 14 L L 14 14 L 27 11 59 43 27 11 L 13 13 L L 13 13 L L 13 13 L 26 10 58 42 26 10 L 12 12 L L 12 12 L L 12 12 L 25 9 57 41 25 9 L 11 11 L L 11 11 L L 11 11 L +24V +24V +24V +24V 5V 5V 10 10 10 10 10 10 COM3 COM1 COM7 COM5 COM3 COM1 9 9 9 9 9 9 24 8 56 40 24 8 8 8 8 8 L L L L L 8 8 L 23 7 55 39 23 7 7 7 7 7 L L L L L 7 7 L 22 6 54 38 22 6 L 6 6 L L 6 6 L 6 6 L L 21 5 53 37 21 5 L 5 5 L L 5 5 L 5 5 L L + + + 20 4 52 36 20 4 L 4 4 L L 4 4 L L 4 4 L 19 3 51 35 19 3 L 3 3 L L 3 3 L L 3 3 L 18 2 50 34 18 2 L 2 2 L L 2 2 L L 2 2 L 17 1 49 33 17 1 1 1 1 1 L L L L L 1 1 L Note: Viewed from the front of the module. Note: Viewed from the front of the module. F3YD64-1M Transistor output module BA 12 / 24V+ 12 / 24V + 20 20 12 / 24V – 12 / 24V – 19 19 18 18 OUT 8 17 17 OUT 8 7 16 16 7 6 15 15 6 5 14 14 5 4 13 13 4 3 12 12 3 2 11 11 2 OUT 1 10 10 OUT 1 9 9 DATA 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4 3 3 3 2 2 2 DATA 1 1 1 Note: Viewed from the front of the module. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 + + + + + + <> <> 27 � Terminal Arrangement � External Connection Method Terminal 10-point 18-point Connector Type Connector Connector Block Type terminal block terminal block Flat cable, 32-point 64-point 2 Applicable 2 0.26 mm 0.08 - 1.27 mm connector connector 0.33 - 0.82 mm 2 max. 0.20 mm pitch, conductor size BA BA BA 2 0.08 mm 12 20 20 20 20 20 20 Wire connection 1 1 Solderless Soldered Solderless Solderless 19 19 19 19 19 19 method 2 18 18 18 18 18 18 Rated wire 2 3 75°C min. 17 17 17 17 17 17 temperature 4 16 16 16 16 16 16 Copper Wire Material 3 5 15 15 15 15 15 15 Solderless For 3.5 mm 6 — 14 14 14 14 14 14 terminals terminal 4 7 13 13 13 13 13 13 0.8 N·m Crimping 8 {8 kgf·cm, — 12 12 12 12 12 12 torque 6.9 lbf·in} 5 9 11 11 11 11 11 11 Example: 10 10 10 10 10 10 10 Japan 6 11 Solderless 9 9 9 9 9 9 12 Applicable Terminal 8 8 8 8 8 8 solderless Mfg Co., Ltd.: — 7 13 7 7 7 7 7 7 V1.25-M3 terminal 14 Nippon Tanshi 6 6 6 6 6 6 8 15 Co., Ltd.: 5 5 5 5 5 5 RAV1.25-3.5 16 4 4 4 4 4 4 9 17 3 3 3 3 3 3 � Applicable External Connectors 18 2 2 2 2 2 2 Connection Method Applicable Connector 10 1 1 1 1 1 1 Fujitsu : FCN-361J040-AU connector Soldered type FCN-360C040-B connector cover M3.5 Fujitsu : FCN-363J040 housing M3.5 Solderless type FCN-363J-AU contact FCN-360C040-B connector cover 8.2 mm 7.1 mm Fujitsu : Solderless type FCN-367J040-AU/F 8.2 mm 6.4 mm 7.1 mm Operating Environment There is no restriction on the type of CPU modules that can be used with this module. Model and Suffix Codes Model Suffix code Style code Option code Description Transistor output, 24 V DC 2 A, 4 points, all points independent F3YD04 -7N . . . . . . . . . . F3Y A08 -2N . . . . . . . . . . TRIAC output, 100－240 V AC 1 A, 8 points Relay output, 24 V DC, 100－240 V AC 2 A, 8 points, all points independent F3YC08 -0C . . . . . . . . . . F3YC08 -0N . . . . . . . . . . Relay output, 24 V DC, 100－240 V AC 2 A, 8 points Relay output, 24 V DC, 100－240 V AC 2 A, 16 points F3YC16 -0N . . . . . . . . . . F3YD08 -6 A . . . . . . . . . . Transistor output (sink type), 12－24 V DC 1 A, 8 points Transistor output (source type), 12－24 V DC 1 A, 8 points F3YD08 -6B . . . . . . . . . . F3YD08 -7A . . . . . . . . . . Transistor output (sink type), 12－24 V DC 2 A, 8 points Transistor output (sink type), 12－24 V DC 0.5 A, 14 points F3YD14 -5 A . . . . . . . . . . F3YD14 -5B . . . . . . . . . . Transistor output (source type), 12－24 V DC 0.5 A, 14 points Transistor output (sink type), 12－24 V DC 0.1 A, 32 points* F3YD32 -1 A . . . . . . . . . . F3YD32 -1B . . . . . . . . . . Transistor output (source type), 12－24 V DC 0.1 A, 32 points* TTL output, 5 V DC, 32 points* F3YD32 -1T . . . . . . . . . . F3YD64 -1 A . . . . . . . . . . Transistor output (sink type), 24 V DC 0.1 A, 64 points* Transistor output (sink type), 24 V DC 0.1 A, 64 points* F3YD64 -1F . . . . . . . . . . F3YD64 -1M . . . . . . . . . . Transistor output (matrix scan), 12－24 V DC 0.1 A, 64 points *: See the section on spare parts in the FA-M3 Range-free Multi-controller (GS 34M6A01-01E) for information on connectors. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Solderless terminal <> <> 28 External Dimensions F3YA08, F3YD04, F3YC08-0N, F3YD08 F3YD14, F3YC08-0C,F3YC16 Unit: mm F3YD32 F3YD64-1A, F3YD64-1F F3YD64-1M All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 29 F3YD32-1H General High-Speed Transistor Output Modules Specifications (sink type with short-circuit protector) General F3YD32-1H is a high-speed transistor output module with 32 outputs. Features - Built-in protection against output short-circuit - High speed response of 0.1 ms max. - Support for multi-channel pulse output applications Specifications Item F3YD32-1H Output type Transistor contact (sink type) Number of points 32 8 points/common Common line type Isolation method Photocoupler isolation 1500 V AC for one minute between the group - Ensure that the polarity of the external power supply is correct. of terminals for external connection and the Withstanding voltage Otherwise, a short-circuit condition may damage an output element, internal circuit with smoldering and scattering of broken pieces. Rated load voltage 12 to 24 V DC - Ensure that the polarity of the external power supply is correct. (10.2 to 26.4 V DC) (Operating voltage range) Otherwise, a short-circuit condition may damage an output element, 0.1 A/point and cause smoldering and scattering of chips. Beware that wrongly Maximum load current 0.5 A/common connecting a connector wired for F3XD32 or F3XD64 to the module 0.1 ms max. Response OFF→ON may disable the protectors and damage internal elements. *2: If an inductive load, such as a relay, is to be connected, a surge time ON→OFF 0.1 ms max. protector is also required on the load side. Connect a surge protector ON voltage 0.5 V DC max. or a diode across the load nearby so that the module output terminal Off-time leak current 0.1 mA max. voltage will not exceed the specified operating load voltage range. Service life Mechanical — *3: The contact operation of the output block of the circuit and the LED display operate independently and thus may be inconsistent in the Short Limits short-circuit current. *1 event of an error. Protectors -circuit *4: For details on the module behavior when the CPU fails, see the Shuts off output when overheat is detected. Overheat Severity of Failures and LED Display” in the FA-M3 Range-free *2 Surge Protector Active clamp Multi-controller (GS 34M6A01-01E). None Fuse *5: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or 165 mA (5 V DC) F3SP67 is used, all points can be specified in 16-point units. Current consumption *3 Output display LED (Lit when output is on) When a sequence CPU is used: Components and Functions Output status when Initial value: RESET *5 *4 All module outputs can be set collectively. program stops When a BASIC CPU is used: HOLD/RESET 1 5 9 13 172125 29 No setting function; 2 6 10 141822 26 30 3 7 1115 19232731 always set to HOLD 4 8 121620 2428 32 Indicates the on/off status External power supply 12 to 24 V DC, 30 mA of the outputs. External connection One 40-pin connector 110 g Weight *1: Operation of the protection circuitry: - If short-circuit occurs, the ON voltage increases and the short-circuit current is limited within the range 1-3 A. - If the short-circuit condition is removed, normal operation resumes. - If the short-circuit condition persists, the short-circuit current may cause the temperature of the output element to reach approx. 160°C, triggering the overheat protector to shut down the output. - If the temperature of the overheated output element then drops by approximately 10°C, normal operation resumes. - The overheat protector will not be triggered if the module is operated normally within its specifications with no short-circuit condition. - Both the short-circuit protector and overheat protector are designed to control outputs individually. Under some short-circuit conditions, however, the overheat protector may shut down not only its associated output but also other outputs. - Short-circuit and overheat protectors are designed to protect the output element against short-term short-circuit. Never leave the module in prolonged short-circuit condition. Otherwise, the module enclosure may deteriorate or the PCB may be discolored. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 30 External Connection Diagram Applicable External Connectors Connection Method Applicable Connector Fujitsu: F3YD32-1H Soldered type FCN-361J040-AU connector FCN-360C040-B connector cover Fujitsu: FCN-363J040 connector Solderless type FCN-363J-AU contact FCN-360C040-B connector cover Fujitsu: Solderless type FCN-367J040-AU/F Operating Environment This module is compatible with all CPU module types. Model and Suffix Codes Suffix Style Option Model Description Code Code Code Transistor output, 32 points F3YD32 -1H . . . . . . . . . . (high-speed output with short-circuit protector) Note: Viewed from the front of the module. External Dimensions Terminal Arrangement F3YD32-1H Unit: mm Internal Circuit Diagram 10 Constant voltage circuit 9 COM 8 Ｌ Bus Interface - + Overheat protector Overcurrent protector 1 Ｌ External Connection Method 0.08-0.20 2 Applicable 0.26 mm 2 Flat cable, 1.27 mm mm 2 conductor size max. pitch, 0.08 mm max. Wire connection Soldered Solderless Solderless method Rated wire 75°C min. temperature Wire material Copper All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Internal bus <> <> 31 F3YD32-1P, F3YD64-1P General Transistor Output Modules Specifications (sink type with short-circuit protector) General F3YD32-1P and F3YD64-1P are 32- and 64-point transistor output modules respectively. Features - The modules have built-in protection against output short-circuit. Specifications Model F3YD32-1P F3YD64-1P - Short-circuit and overheat protectors are designed to protect the Output type Transistor contact (sink type) output element against short-term short-circuit. Never leave the Number of points 32 64 module in prolonged short-circuit condition. Otherwise, the module 8 points/common enclosure may deteriorate or the PCB may be discolored. Common line type - Ensure that the polarity of the external power supply is correct. Isolation method Photocoupler isolation Otherwise, a short-circuit condition may damage an output element, 1500 V AC for one minute between the and cause smoldering and scattering of chips. Beware that wrongly group of terminals for external connection Withstanding voltage connecting a connector wired for F3XD32 or F3XD64 to the module and the internal circuit may disable the protectors and damage internal elements. Rated load voltage 12 to 24 V DC *2: If an inductive load, such as a relay, is to be connected, a surge (10.2 to 26.4 V DC) (Operating voltage range) protector is also required on the load side. Connect a surge protector 0.1 A/point 0.1 A/point or a diode across the load nearby so that the module output terminal Maximum load current 0.5 A/common 0.4 A/common voltage will not exceed the specified operating load voltage range. Response OFF→ON 1 ms max. *3: The contact operation of the output block of the circuit and the LED display operate independently and thus may be inconsistent in the time 1 ms max. ON→OFF event of an error. ON voltage 0.5 V DC max. *4: For details on the module behavior when the CPU fails, see the Off-time leak current 0.1 mA max. Severity of Failures and LED Display” in the FA-M3 Range-free Multi-controller (GS 34M6A01-01E). Service life Mechanical — *5: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or Short Controlled short-circuit current F3SP67 is used, all points can be specified in 16-point units. *1 Protectors -circuit Output shutdown Overheat *2 Components and Functions Surge Protector Active clamp circuit None Fuse Current consumption 160 mA (5 V DC) 275 mA (5 V DC) 1 5 9 13 17 21 25 29 2 6 10 14 18 22 26 30 LED (Lit when 3 7 11 15 19 23 27 31 Output LEDs 4 8 12 16 20 24 28 32 LED (Lit when outputs are turned on *3 Indicates the on/off status of Output display DC I/O output is on) for a switched LED the outputs. DISPLAY group) 12 Display Selector Switch When a sequence CPU is used: Default: RESET Switches display of output Output status when Can be set globally on a LEDs. Not present on 32-point *5 *4 program stops module-by-module basis modules. HOLD/RESET When a BASIC CPU is used: No setting function; The status is always HOLD 12 to 24 V DC 12 to 24 V DC External power supply 55 mA 95 mA One or two 40-pin connectors One 40-pin Two 40-pin External connection 32-point modules have only connector connectors one connector. 110 g 130 g Weight *1: Operation of the protection circuitry: - If short-circuit occurs, the ON voltage increases and the short-circuit current is limited within the range 1-3 A. - If the short-circuit condition is removed, normal operation resumes. - If the short-circuit condition persists, the short-circuit current may cause the temperature of the output element to reach approx. 160°C, triggering the overheat protector to shut down the output. - If the temperature of the overheated output element then drops by Display Selector about 10°C, normal operation resumes. Output LEDs 1-32 Switch Position - The overheat protector will not be triggered if the module is operated normally within its specifications with no short-circuit condition. 1 Indicates on/off statuses of outputs 1 to 32. - Both the short-circuit protector and overheat protector are designed 2 Indicates on/off statuses of outputs 33 to 64. to control outputs individually. Under some short-circuit conditions, however, the overheat protector may shut down not only its associated output but also other outputs. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 32 External Connection Diagram Internal Circuit Diagram F3YD32-1P External Connection Method 2 0.08-0.20 Applicable 0.26 mm Flat cable, 1.27 mm 2 mm 2 conductor size max. pitch, 0.08 mm max. Wire connection Soldered Solderless Solderless method Rated wire Note: Viewed from the front of the module. 75°C min. temperature Copper Wire material F3YD64-1P Applicable External Connectors Connection Method Applicable Connector Fujitsu: Soldered type FCN-361J040-AU connector FCN-360C040-B connector cover Fujitsu: FCN-363J040 connector Solderless type FCN-363J-AU contact FCN-360C040-B connector cover Fujitsu: Solderless type FCN-367J040-AU/F Operating Environment This module is compatible with all CPU module types. Note: Viewed from the front of the module. Model and Suffix Codes Suffix Style Option Model Description Terminal Arrangement Code Code Code 32-point 64-point 32-point transistor F3YD32 -1P . . . . . . . . . . output with short-circuit protector 64-point transistor -1P . . . . . . . . . . output with short-circuit F3YD64 protector All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Internal bus <> <> 33 External Dimensions Unit: mm F3YD32-1P F3YD64-1P All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 34 Blank Page All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 35 F3YD32-1R, F3YD64-1R General Transistor Output Modules Specifications (source type with short-circuit protector) General F3YD32-1R and F3YD64-1R are 32- and 64-point transistor output modules respectively. Features The modules have built-in protection against output short-circuit. Specifications Model F3YD32-1R F3YD64-1R Output type Transistor contact (source-type) Number of points 32 64 - Short-circuit and overheat protectors are designed to protect the output element against short-term short-circuit. Never leave the 8 points/common Common line type module in prolonged short-circuit condition. Otherwise, the module Isolation method Photocoupler isolation enclosure may deteriorate or the PCB may be discolored. 1500 V AC for one minute between the - Ensure that the polarity of the external power supply is correct. Withstanding voltage group of terminals for external connection Otherwise, a short-circuit condition may damage an output element, and cause smoldering and scattering of chips. and the internal circuit - Beware that wrongly connecting a connector wired for F3XD32 or *1 Rated load voltage 12 to 24 V DC F3XD64 to the module may disable the protectors and damage (10.2 to 26.4 V DC) (Operating voltage range) internal elements. *3: If an inductive load, such as a relay, is to be connected, a surge 0.1 A/point 0.1 A/point Maximum load current protector is also required on the load side. Connect a surge 0.5 A/common 0.4 A/common protector or a diode across the load nearby so that the module 1 ms max. Response OFF→ON output terminal voltage will not exceed the specified operating load time 1 ms max. voltage range. ON→OFF *4: The contact operation of the output block of the circuit and the LED 0.5 V DC max. ON voltage display operate independently and thus may be inconsistent in the Off-time leak current 0.1 mA max. event of an error. *5: For details on the module’s behavior when the CPU fails, see the Service life Mechanical — Severity of Failures and LED Display” in the FA-M3 Range-free Short Multi-controller (GS 34M6A01-01E). Controlled short-circuit current. *2 Protectors -circuit *6: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or F3SP67 is used, all points can be specified in 16-point units. Output shutdown Overheat *3 None Surge Protector Components and Functions None Fuse 170 mA (5 V DC) 275 mA (5 V DC) Current consumption LED (Lit when 1 5 9 1317212529 2 6 101418222630 3 7 11 1519232731 LED (Lit when output outputs are turned Output LEDs *4 4 8 121620242832 Output display is on) on for a switched Indicates the on/off status of YD 1R DC OUT LED group) DISPLAY the outputs. When a sequence CPU is used: 12 Initial value: RESET Output status when All module outputs can be set collectively. Display Selector Switch *6 *5 program stops Switches display of output When a BASIC CPU is used: HOLD/RESET LEDs. Not present on 32-point No setting function; modules. always set to HOLD 12 to 24 V DC 12 to 24 V DC *1 External power supply 60 mA 110 mA One or two 40-pin connectors One 40-pin Two 40-pin External connection 32-point modules have only connector connectors Weight 110 g 130 g one connector. *1 The external power supply and the load power supply must be identical. Using separate power sources is not allowed even if they have the same voltage. *2: Operation of the protection circuitry: - If short-circuit occurs, the ON voltage increases and the short-circuit current is limited within the range 1-3 A. - If the short-circuit condition is removed, normal operation resumes. - If the short-circuit condition persists, the short-circuit current may cause the temperature of the output element to reach approx. Display Selector Output LEDs 1-32 160°C, triggering the overheat protector to shut down the output. Switch Position - If the temperature of the overheated output element then drops by 1 Indicates on/off statuses of outputs 1 to 32. about 10°C, normal operation resumes. Indicates on/off statuses of outputs 33 to 64. 2 - The overheat protector will not be triggered if the module is operated normally within its specifications with no short-circuit condition. - Short-circuit protectors are designed to control outputs individually. On the other hand, the overheat protectors control outputs in pairs: OUT1 and OUT2, OUT3 and OUT4, …, OUT63 and OUT64. Under some short-circuit conditions, however, a overheat protector may shut down not only its associated outputs but also other outputs. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 36 External Connection Diagram Internal Circuit Diagram F3YD32-1R Constant 9COM voltage circuit 8 Ｌ Bus interface + Overheat protector Overcurrent protector - 1 Ｌ 10 External Connection Method 2 2 Applicable 0.26 mm 0.08-0.20 mm Flat cable, 1.27 mm 2 conductor size max. max. pitch, 0.08 mm Wire connection Soldered Solderless Solderless method Rated wire 75°C min. temperature Note: Viewed from the front of the module. Copper Wire material F3YD64-1R Applicable External Connectors Connection Method Applicable Connector Fujitsu: FCN-361J040-AU connector Soldered type FCN-360C040-B connector cover Fujitsu: FCN-363J040 connector Solderless type FCN-363J-AU contact FCN-360C040-B connector cover Fujitsu: Solderless type FCN-367J040-AU/F Operating Environment This module is compatible with all CPU module types. Model and Suffix Codes Suffix Style Option Model Description Code Code Code 32-point transistor F3YD32 -1R . . . . . . . . . . output with short-circuit Note: Viewed from the front of the module. protector 64-point transistor Terminal Arrangement F3YD64 -1R . . . . . . . . . . output with short-circuit protector 32-point 64-point All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Internal bus <> <> 37 External Dimensions Unit: mm F3YD32-1R F3YD64-1R All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 38 Blank Page All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 39 F3WD64-†F General Input/Output Module Specifications General The F3WD64 Input/Output Module is intended for use in an input/output slot of the FA-M3 Range-free Multi-controller. It has 32-point inputs and outputs (sink type) and is provided with two 40-pin connectors. Each input/output point is isolated from the internal circuit by a photocoupler. The F3WD64 input/output module uses an 8-point/common configuration for both input and output. The operating voltage is either 12 V DC or 24 V DC. Specifications *1 *1 Item F3WD64-3F F3WD64-4F Input type DC voltage 32 (Terminal Nos. 01 to 32) Number of inputs Common line type 8 points/common Isolation method Photocoupler Isolation Rated input voltage 24 V DC 12 V DC (operating voltage range) (20.4 to 26.4 V DC) (10.2 to 13.2 V DC) Rated input current 4.1 mA/point (24 V DC) 4.1 mA/point (12 V DC) Components and Functions 16 V DC min. 8 V DC min. ON Operating 3.2 mA min. 2.6 mA min. voltage/current 5.8 V DC max. 3.4 V DC max. 1 5 9 13 17 21 25 29 OFF 2 6 10 14 18 22 26 30 0.9 mA max. 1.0 mA max. Input/Output LEDs 3 7 11 15 19 23 27 31 4 8 12 16 20 24 28 32 Input sampling period can be specified between 0 Indicates the on/off status OFF JON *2 DC I/O and 1 ms in 4 levels of the inputs and outputs. Response time DISPLAY Input sampling period can be specified between 0 ONJOFF *2 IN OUT and 1 ms in 4 levels Display selector switch Interrupt None Selects the input/output Maximum ratio of inputs LED indication. 60% 100% turned on simultaneously Output Type Transistor contact (sink type) Number of outputs 32 (Terminal Nos. 33 to 64) Common line type 8 points/common Isolation method Photocoupler Isolation Two 40-pin connectors Rated Load Voltage 24 V DC 12 V DC (operating voltage range) (20.4 to 26.4 V DC) (10.2 to 13.2 V DC) Maximum load current 0.1 A/point, 0.4 A/common OFFJON 1 ms max. Response time ONJOFF 1 ms max. ON voltage 0.5 V DC max. 0.1 mA max. OFF-time leakage current Surge Protector Zener diode When a sequence CPU is used: Initial value: RESET Output status when program All module outputs can be set collectively *3 *4 stops on a module basis Display selector LED Indication HOLD/RESET When a BASIC CPU is used: switch position No setting function; Indicates the on/off status of IN always set to HOLD. inputs 1 to 32. Indicates the on/off status of 24 V DC, 60 mA 12 V DC, 60 mA External power supply OUT outputs 33 to 64. Input/Output status Lit when status is on (Input or output status indication indication can be selected using a switch.) Current Consumption 200 mA External Connection Two 40-pin connectors Weight 160 g *1: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or F3SP67 is used, the output for CPU fatal errors can be set either to HOLD or RESET. *2: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or F3SP67 is used. For other CPU modules, the specification is the same as the F3WD64-†N.The actual response time can be obtained by adding the following values: - 100 µs (OFF J ON) - 300 µs (ON J OFF) *3: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or F3SP67 is used, all points can be specified in 16-point units. *4: For details on the module behavior when the CPU fails, see the Severity of Failures and LED Display” in the FA-M3 Range-free Multi-controller (GS 34M6A01-01E). All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Common Output Block Input Block ~ ~ <> <> 40 Internal Circuit Diagram External Connection Method Connector Type 2 Flat cable, Applicable 0.26 mm 0.08 - 10 1.27 mm pitch, 2 conductor size max. 0.20 mm 2 0.08 mm Wire connection 9 COM Soldered Solderless Solderless method 8 Rated wire – 75 °C min. L temperature + Copper Wire Material Bus 1 interface L 9COM Applicable External Connectors 8 Connection Applicable Connector + Method – Fujitsu : 1 1 FCN-361J040-AU connector Soldered type Display FCN-360C040-B connector cover 2 selector Fujitsu : FCN-363J040 housing Solderless type FCN-363J-AU contact External Connection Diagram FCN-360C040-B connector cover Fujitsu : CN2(Output block) Solderless type FCN-367J040-AU / F CN1(Input block) BA BA 12/24V* 12/24V* 20 20 20 20 COM8 COM6 19 19 19 19 Operating Environment COM4 COM2 64 48 18 18 L L 18 18 32 16 63 47 17 17 There is no restriction on the type of CPU modules that L 17 17 L 31 15 62 46 16 16 L 16 16 L can be used with this module. 30 14 61 45 15 15 L 15 15 L 29 13 ＋ － － ＋ ＋ 60 ＋ 44 14 14 L L 14 14 28 12 59 － ＋ ＋ － 43 13 13 L L 13 13 27 11 58 42 Model and Suffix Codes 12 12 L L 12 12 26 10 57 41 11 11 L L 11 11 Suffix Style Option 25 9 Model Description 12/24V* 12/24V* 10 10 10 10 code code code COM3 COM1 COM7 COM5 9 9 9 9 24 8 56 40 F3WD64 -3F . . . . . . . . . . 24 V DC input/output 8 8 L 8 8 L 23 7 55 39 7 7 L 7 7 L F3WD64 -4F . . . . . . . . . . 12 V DC input/output 22 6 54 38 6 6 L 6 6 L 21 5 ＋ － － ＋ *: See the section on spare parts in FA-M3 Range-free Multi-controller 53 37 5 5 L L 5 5 20 4 ＋ 52 36 ＋ (GS 34M6A01-01E) for information on connectors. － ＋ ＋ － 4 4 L L 4 4 19 3 51 35 3 3 L L 3 3 18 2 50 34 2 2 L L 2 2 17 1 49 33 External Dimensions 1 1 L L 1 1 F3WD64-�F Note : Viewed from the front of the module. * : 24 V for F3WD64-3F and 12 V for F3WD64-4F. Unit: mm All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Internal bus + – <> <> 41 F3WD64-†N General Input/Output Module Specifications General The F3WD64 Input/Output Module is intended for use in an input/output slot of the FA-M3. It has 32-point inputs and outputs (sink type) and is provided with two 40-pin connectors. Each input/output point is isolated from the internal circuit by a photocoupler. The F3WD64 input/output module uses an 8-point/common configuration for both input and output. The operating voltage is either 12 V DC or 24 V DC. Specifications Item F3WD64-3N F3WD64-4N Input type DC voltage 32 (Terminal Nos. 01 to 32) Number of inputs Common line type 8 points/common Isolation method Photocoupler Isolation Rated input voltage 24 V DC 12 V DC (operating voltage (20.4 to 26.4 V DC) (10.2 to 13.2 V DC) range) Rated input current 4.1 mA/point (24 V DC) 4.1 mA/point (12 V DC) Components and Functions 16 V DC min. 8 V DC min. Operating ON 3.2 mA min. 2.6 mA min. voltage/cur 5.8 V DC max. 3.4 V DC max. rent OFF 1 5 9 13 17 21 25 29 0.9 mA max. 1.0 mA max. 2 6 10 14 18 22 26 30 Input/Output LEDs 3 7 11 15 19 23 27 31 Response OFFJON 1.0 ms max. 4 8 12 16 20 24 28 32 Indicates the on/off status DC I/O time ONJOFF 2.5 ms max. of the inputs and outputs. DISPLAY Interrupt None IN OUT Maximum ratio of Display selector switch 60% 100% inputs turned on Selects the input/output simultaneously LED indication. Output type Transistor contact (sink type) Number of outputs 32 (Terminal Nos. 33 to 64) Common line type 8 points/common Isolation method Photocoupler isolation Rated load voltage 24 V DC 12 V DC Two 40-pin connectors (operating voltage (20.4 to 26.4 V DC) (10.2 to 13.2 V DC) range) Maximum load current 0.1 A/point 0.4 A/common Response OFFJON 1 ms max. time ONJOFF 1 ms max. ON voltage 0.5 V DC max. OFF-time leakage 0.1 mA max. current Surge Protector Zener diode When a sequence CPU is used: Initial value: RESET Output status when *1 All module outputs can be set collectively. *2 Display selector program stops LED Indication When a BASIC CPU is used: switch position HOLD/RESET No setting function; Indicates the on/off status of always set to HOLD. IN inputs 1 to 32. External power supply 24 V DC, 60 mA 12 V DC, 60 mA Indicates the on/off status of Input/Output status Lit when status is on (Input or output status indication can be OUT outputs 33 to 64. selected using a switch.) indication Current consumption 200 mA External connection Two 40-pin connectors Weight 160 g *1: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or F3SP67 is used, all points can be specified in 16- point units. *2: For details on the module’s behavior when the CPU fails, see the Severity of Failures and LED Display” in the FA-M3 Range-free Multi-controller (GS 34M6A01-01E). All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Common Output Block Input Block ~ ~ <> <> 42 Internal Circuit Diagram External Connection Method Connector Type 2 Flat cable, Applicable 0.26 mm 0.08 - 10 1.27 mm pitch, 2 conductor size max. 0.20 mm 2 0.08 mm Wire connection 9 COM Soldered Solderless Solderless method 8 Rated wire – 75 °C min. L temperature + Copper Wire Material Bus 1 interface L 9COM Applicable External Connectors 8 Connection Applicable Connector + Method – Fujitsu : 1 1 FCN-361J040- AU connector Soldered type Display FCN-360C040-B connector cover 2 selector Fujitsu : FCN-363J040 housing Solderless type FCN-363J- AU contact External Connection Diagram FCN-360C040-B connector cover Fujitsu : CN2(Output block) Solderless type FCN-367J040- AU / F CN1(Input block) BA BA 12/24V* 12/24V* 20 20 20 20 COM8 COM6 19 19 19 19 COM4 COM2 64 48 18 18 Operating Environment L 18 18 L 32 16 63 47 17 17 L L 17 17 31 15 There is no restriction on the type of CPU modules that 62 46 16 16 L 16 16 L 30 14 61 45 15 15 can be used with this module. L L 15 15 29 13 ＋ ＋ ＋ － － ＋ 60 44 14 14 L 14 14 L 28 12 59 43 － ＋ ＋ － 13 13 L L 13 13 27 11 58 42 12 12 L 12 12 L Model and Suffix Codes 26 10 57 41 11 11 L L 11 11 25 9 12/24V* 12/24V* 10 10 10 10 Suffix Style Option COM3 COM1 COM7 COM5 Model Description 9 9 9 9 code code code 24 8 56 40 8 8 L 8 8 L 23 7 55 39 F3WD64 -3N . . . . . . . . . . 24 V DC input/output 7 7 L L 7 7 22 6 54 38 6 6 L 6 6 L F3WD64 -4N . . . . . . . . . . 12 V DC input/output 21 5 ＋ － － ＋ 53 37 5 5 L L 5 5 20 4 ＋ ＋ 52 36 － ＋ ＋ － *: See the section on spare parts in FA-M3 Range-free Multi-controller 4 4 L 4 4 L 19 3 51 35 3 3 (GS 34M6A01-01E) for information on connectors. L L 3 3 18 2 50 34 2 2 L L 2 2 17 1 49 33 1 1 L L 1 1 External Dimensions Note : Viewed from the front of the module. F3WD64-�N * : 24 V for F3WD64-3N and 12 V for F3WD64-4N. Unit: mm All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Internal bus + – <> <> 43 F3WD64-†P General Input/Output Module Specifications (sink type with short-circuit protector) General The F3WD64 Input/Output Module is intended for use in an input/output slot of the FA-M3. It has 32-point inputs and outputs (sink type) and is provided with two 40-pin connectors. Each input/output point is isolated from the internal circuit by a photocoupler. The F3WD64 input/output module uses an 8-point/common configuration for both input and output. The operating voltage is either 12 V DC or 24 V DC. Features The modules have built-in protection against output short-circuit. Specifications *1: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or Item F3WD64-3P F3WD64-4P F3SP67 is used. For other CPU modules, the OFF J ON response Input type DC voltage time is 1.0 ms (max.) and the OFF J ON response time is 2.5 ms (max.). The actual response time can be obtained by adding the Number of inputs 32 (Terminal Nos. 01 to 32) following values: Common line type 8 points/common Isolation method Photocoupler Isolation - 100 µs (OFF J ON) 1500 V AC for one minute between the group of - 300 µs (ON J OFF) Withstanding voltage terminals for external connection and the *2: Operation of the protection circuitry: internal circuit - If short-circuit occurs, the ON voltage increases and the short-circuit Rated input voltage 24V DC 12V DC current is limited within the range 1-3 A. (Operating voltage range) (20.4 to 26.4V DC) (10.2 to 13.2V DC) - If the short-circuit condition is removed, normal operation resumes. 4.1 mA/point (24 V 4.1 mA/point (12 V DC) - If the short-circuit condition persists, the short-circuit current may Rated input current DC) cause the temperature of the output element to reach approx. 160°C, 16 V DC min. 8 V DC min. triggering the overheat protector to shut down the output. Operating ON 3.2 mA min. 2.6 mA min. voltage/ - If the temperature of the overheated output element then drops by 5.8 V DC max. 3.4 V DC max. current OFF about 10°C, normal operation resumes. 0.9 mA max. 1.0 mA max. - The overheat protector will not be triggered if the module is operated Input sampling period can be specified OFFJON *1 Response between 0 and 1 ms in 4 levels normally within its specifications with no short-circuit condition. time Input sampling period can be specified - Both the short-circuit protector and overheat protector are designed to ONJOFF *1 between 0 and 1 ms in 4 levels control outputs individually. Under some short-circuit conditions, Interrupt None however, the overheat protector may shut down not only its associated Maximum ratio of inputs output but also other outputs. 60% 100% turned on simultaneously - Short-circuit and overheat protectors are designed to protect the Output type Transistor contact (sink type) output element against short-term short-circuit. Never leave the Number of outputs 32 (Terminal Nos. 33 to 64) module in prolonged short-circuit condition. Otherwise, the module Common line type 8 points/common enclosure may deteriorate or the PCB may be discolored. Isolation method Photocoupler isolation - Ensure that the polarity of the external power supply is correct. Rated load voltage 24 V DC 12 V DC Otherwise, a short-circuit condition may damage an output element, (Operating voltage range) (20.4 to 26.4 V DC) (10.2 to 13.2 V DC) and cause smoldering and scattering of chips. Beware that wrongly Maximum load current 0.1 A/point 0.4 A/common connecting a connector wired for F3XD32 or F3XD64 to the module Response OFFJON 1 ms max. may disable the protectors and damage internal elements. time ONJOFF 1 ms max. *3: If an inductive load, such as a relay, is to be connected, a surge ON voltage 0.5 V DC max. protector is also required on the load side. Connect a surge protector OFF-time leakage current 0.1 mA max. or a diode across the load nearby so that the module output terminal Short voltage will not exceed the specified operating load voltage range. Controlled short-circuit current *2 -circuit Protectors *4: For details on the module behavior when the CPU fails, see the Overheat Output shutdown Severity of Failures and LED Display” in the FA-M3 Range-free *3 Surge Protector Active clamp circuit Multi-controller (GS 34M6A01-01E). Fuse None *5: When F3SP28, F3SP38, F3SP53, F3SP58, F3SP59, F3SP66 or When a sequence CPU is used: F3SP67 is used, all points can be specified in 16-point units. Default: RESET Output status when *6: The contact operation of the output block of the circuit and the LED *4 Can be set globally on a module-by-module program stops display operate independently and thus may be inconsistent in the *5 basis HOLD/RESET event of an error. When a BASIC CPU is used: No setting function; the status is always HOLD. External power supply 24 V DC, 55 mA 12 V DC, 55 mA 1500 V AC for one minute between the group of Withstanding voltage terminals for external connection and the internal circuit Input/Output status Lit when status is on (Input or output status *6 indication indication can be selected using a switch.) Current consumption 170 mA External connection Two 40-pin connectors Weight 120 g All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 Common Output Block Input Block <> <> 44 Components and Functions Terminal Arrangement 1 5 9 13 17 21 25 29 2 6 10 14 18 22 26 30 Input/Output LEDs 3 7 11 15 19 23 27 31 4 8 12 16 20 24 28 32 Indicates the on/off status WD64 P DC I/O of the inputs and outputs. DISPLAY IN OUT Display selector switch Selects the input/output LED indication. Two 40-pin connectors External Connection Method Display selector LED Indication Connector Type switch position Indicates the on/off status of Flat cable, 2 IN Applicable 0.26 mm 0.08 - inputs 1 to 32. 2 1.27 mm pitch, conductor size max. 0.20 mm 2 Indicates the on/off status of 0.08 mm OUT outputs 33 to 64. Wire connection Soldered Solderless Solderless method Internal Circuit Diagram Rated wire 75 °C min. temperature Constant Wire Material Copper 10 voltage circuit 9COM 8 Applicable External Connectors L - Connection Applicable Connector + Method Overheat protector Overcurrent protector Bus 1 Fujitsu : Interface L Soldered type FCN-361J040- AU connector 9 COM FCN-360C040-B connector cover 8 Fujitsu : - + FCN-363J040 housing - + Solderless type FCN-363J- AU contact FCN-360C040-B connector cover IN Fujitsu : 1 Display Solderless type FCN-367J040- AU / F OUT selector Operating Environment External Connection Diagram There is no restriction on the type of CPU modules that CN2(Output block) CN1(Input block) can be used with this module. BA BA 12/24V* 12/24V* 20 20 20 20 COM8 COM6 19 19 19 19 COM4 COM2 64 48 18 18 L 18 18 L Model and Suffix Codes 32 16 63 47 17 17 L L 17 17 31 15 62 46 16 16 Suffix Style Option L 16 16 L 30 14 Model Description 61 45 15 15 L L code code code 15 15 29 13 ＋ ＋ ＋ － － ＋ 60 44 14 14 L 14 14 L 28 12 24 V DC input/output 59 43 . . . . . . . . . . － ＋ ＋ － 13 13 L L 13 13 27 11 F3WD64 -3P (with short-circuit 58 42 12 12 L 12 12 L protector) 26 10 57 41 11 11 L L 11 11 25 9 12/24V* 12/24V* 10 10 . . . . . . . . . . 12 V DC input/output 10 10 COM3 COM1 COM7 COM5 9 9 (with short-circuit F3WD64 -4P 9 9 24 8 56 40 8 8 protector) L 8 8 L 23 7 55 39 7 7 L L 7 7 22 6 *: See the section on spare parts in the FA-M3 Range-free 54 38 6 6 L 6 6 L 21 5 Multi-controller (GS 34M6A01-01E) for information on connectors. ＋ － － ＋ 53 37 5 5 L L 5 5 20 4 ＋ ＋ 52 36 － ＋ ＋ － 4 4 L 4 4 L 19 3 51 35 3 3 L L 3 3 18 2 50 34 2 2 L L 2 2 17 1 49 33 1 1 L L 1 1 Note : Viewed from the front of the module. * : 24 V for F3WD64-3P and 12 V for F3WD64-4P. All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 45 External Dimensions F3WD64-�P Unit: mm All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 46 Blank Page All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 47 TA40-0N General Terminal Block Unit Specifications General The TA40-0N Terminal Block Unit is intended for use in the input/output modules that conform to the connector specifications of the FA-M3 Range-free Multi-controller and the FA500 Intelligent Programmable Controller. It allows direct wiring for its slim connector profile. The TA40-0N can be used effectively not only for permanent connections but also for temporary connections such as during debugging. - The ultra-slim connector saves space on the power switch board. - It permits direct mounting on an input/output module, which leads to cost reduction and dispenses with the need for cables. - It can be used with all FA-M3 and FA500 40-pin input/ output connectors. - Using a European type terminal block relieves the user from the burden of soldering or crimping. - It can be secured on an input/output module with screws to facilitate stable operation. External Dimensions Specifications Unit: mm Item Specification 40 Number of points Rated voltage 5-24 V DC Operating voltage range 4.5 - 26.4 V DC Maximum current 0.5 A DC / 1 point 2 Applicable conductor size 0.08 - 0.26 mm ( AWG23 - 28) M2 (slotted head screw) Terminal block screw Clamping screw M2.6 (cross head screw) Color Black Weight 50 g Note: The connector terminal block cannot be used with the F3YP04, F3YP08, F3YP14, F3YP18, F3NC32 and F3NC34 modules. Environment Conditions Item Specification Ambient operating 0°C - 55°C temperature 10 - 90% RH 11.8 4 61.4 Ambient operating humidity (non-condensing) Must be free from the presence of Operating atmosphere corrosive gases or heavy dust. Model and Suffix Codes Suffix Style Option Model Description code code code Terminal block unit, 40 TA40 -0N . . . . . . . . . . points All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 75.4 <> <> 48 Blank Page All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 49 TA50-�N General Connector Terminal Block Unit Specifications KM55-0�� Connector Terminal Block Cable connecting a module and a connector terminal block, select a General suitable cable from the list above. The TA50-0N and TA50-1N Connector Terminal Block Units are intended for use in the input/output modules that conform to the connector specifications of the FA-M3 Range-free Multi-controller or the FA500 Intelligent Programmable Controller. - The TA50-0N and TA50-1N are connected to an input/output unit via the KM55-0�� Connector Terminal Block, which saves space and reduces wiring on the power switch board. - Use of the connector terminal block unit with the connector terminal block cable eliminates soldering work for wiring. - The TA50-0N and TA50-1N can be secured with mounting screws or DIN rails. Terminal Arrangement (TA50-0N) Specifications (TA50-�N) B 1 2 3 4 5 6 7 8 9 1011121314151617181920 Specification 1 2 3 4 5 6 7 8 9 1011121314151617181920 A Item TA50-0N TA50-1N 10 mm Number of points 40 Rated voltage 5-24 V DC Operating voltage range 4.5 - 26.4 V DC Maximum current 0.5 A DC / 1 point Applicable conductor 2 2 2 mm max. 1.25 mm max. size Terminal block screw M3.5 M3 Solderless ø8 mm Solderless ø5.8 mm 8.2 mm Applicable terminal max. max. HIF3B A-40P A-2.54DS A Connector (MIL standard compliant) Terminal Arrangement (TA50-1N) Mounting method 35-mm wide DIN rail or screw mounting M4 (2 points) B 1 234567891011121314151617181920 Clamping screw Color Black Gray 12345 67891011121314151617181920 A Weight 300 g 175 g 7 mm Note: The connector terminal blocks cannot be used with the F3YP04, F3YP08, F3YP14, F3YP18, F3NC32 and F3NC34 modules. Environment Specifications (TA50-�N) Item Specification Ambient operating 0 - 55°C temperature Ambient operating 6 mm 10 - 90% RH (non-condensing) humidity Must be free from the presence of corrosive Operating atmosphere Internal Connection Diagram gases or heavy dust. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 To connector 1 3 5 7 9 1113 151719 2123252729 313335 3739 Specifications (KM55-0��) Item Specification B1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 KM55-005 0.5 m To screw terminal A 12 34 56 7 8 91011121314151617181920 KM55-010 1.0 m KM55-015 1.5 m Note: The pin assignment of the screw terminal matches that of the KM55-020 2.0 m module connectors. KM55-025 2.5 m KM55-030 3.0 m Note: As the connector terminal block does not come with a cable for All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 50 External Dimensions � TA50-0N 2-ø4.5 hole Unit: mm Faceplate 40.5 207 217 226 Note: With a terminal cover Mounting dimension ±0.15 217 M4 � TA50-1N Unit: mm 2-ø4.5 3 5.6 14 141.6 oval holes 150 45 Note: With a terminal cover Mounting dimension ±1 141.6 M4 All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 5 16.5 4 45 17.5 11 4.5 5 40.5 ±0.15 50 55 60 4 <> <> 51 � KM55-0�� Model L +e KM55-005 0.5 m 5 cm KM55-010 1.0 m 1.5 m KM55-015 KM55-020 2.0 m 10 cm KM55-025 2.5 m KM55-030 3.0 m +e* L -0 Model and Suffix Codes Suffix Style Option Model Description code code code -0N . . . . . . . . . . Connector terminal block unit, 40 points（M3.5 screw） TA50 -1N . . . . . . . . . . Connector terminal block unit, 40 points（M3 screw） -005 . . . . . . . . . . Connector terminal block cable, 0.5 m -010 . . . . . . . . . . Connector terminal block cable, 1.0 m -015 . . . . . . . . . . Connector terminal block cable, 1.5 m KM55 -020 . . . . . . . . . . Connector terminal block cable, 2.0 m Connector terminal block cable, 2.5 m -025 . . . . . . . . . . -030 . . . . . . . . . . Connector terminal block cable, 3.0 m All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 52 Blank Page All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 <> <> 53 TA60-0N General Connector Terminal Block Unit Specifications General The TA60-0N Terminal Block Unit is intended for use in the input/output modules that conform to the connector specifications of the FA-M3 Range-free Multi-controller and the FA500 Intelligent Programmable Controller. - The TA60-0N is connected to an input/output unit via the KM55-0�� Connector Terminal Block, which saves space and reduces wiring on the power switch board. - Use of the connector terminal block unit with the connector terminal block cable eliminates soldering work for wiring. - The TA60-0N can be secured with mounting screws or DIN rails. Internal Circuit Diagram - Using a European type terminal block allows a more 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 To connector compact and space-saving design. 1 3 5 7 9 1113 15 1719 2123252729 313335 3739 Specifications B1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Item Specification To screw terminal A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Number of Outputs 40 Note: The pin assignment of the screw terminal matches that of the 5-24 V DC Rated voltage module connectors. Operating voltage range 4.5 - 26.4 V DC 0.5 A DC / 1 point Maximum current 2 Applicable conductor size 0.08 - 0.26 mm （AWG23 - 28） External Dimension M2 (European type terminal) Terminal block screw HIF3B A-40PA-2.54DSA Unit: mm Connector (MIL standard compliant) 35-mm wide DIN rail or screw mounting 37.6 Mounting method Clamping screw M4 (2 points) 99.6 14 Gray Color Weight 80 g Note1: The connector terminal block cannot be used with the F3YP04, F3YP08, F3YP14, F3YP18, F3NC32 and F3NC34 modules. Note2: As the connector terminal block does not come with a cable for connecting a module and a connector terminal block, use the KM55-0�� connector terminal block cable. 2-ø4.5 x 5.6 108 oval holes Environment Specifications Item Specification Ambient operating 0°C - 55°C temperature Ambient operating 10 - 90% RH (non-condensing) humidity Must be free from the presence of corrosive Operating atmosphere gases or heavy dust. Mounting dimension ±1 99.6 M4 Model and Suffix Codes Suffix Style Option Model Description code code code Connector terminal block unit, TA60 -0N ･･････ ･･････ 40 points (European type terminal) All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6G01-01E Apr. 2009-00 16.5 4 45 <> <> 54 Items to Specify When Ordering 1. Model and suffix codes All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 34M6C01-01E Apr. 2009-00 Subject to change without notice.