Manufacturers
YAGEO 4311-119-00087
Description
ANTENNA TDMA LP-MODE CERAMIC SMD
Part Number
4311-119-00087
Price
Request Quote
Manufacturer
YAGEO
Lead Time
Request Quote
Category
PRODUCTS - 4
Datasheet
Extracted Text
WIDE BAND MULTILAYER CERAMIC ANTENNA FOR 850~950MHz 1 Product Specification (Preliminary) QUICK REFERENCE DATA Size 16.5*14*0.9 mm Working Frequency 850~950MHz Gain 1.5 dBi Max VSWR 2 max Polarization Linear Azimuth Omni-directional Impedance 50Ω o Operating Temperature -55~125 C Termination Ni/Sn (Environmentally-Friendly Leadless) o Resistance to soldering heats 260 C, 10 sec. Special Environmental Concerns- Green Products Design: The foil making process is using environmentally friendly aqueous solvent technology. Termination is lead free and packing materials can be re-cycled 1 All the technical data and information contained herein are subject to change without prior notice Print date 02/10/16 R&D Preliminary use only Mar. 13, 02 Oct. 14, 02 Multilayer Ceramic Antenna 4311 119 00087 (LP Mode) for 850~950MHz AN0870000716141B Grant/Cliff. Oct. 14, 02 sheet 190-1 A4 Page 1 spec.doc PHYCOMP Ltd. APPLICATION 17mm 2mm Suggested Layout (60*20 mm ground plane) Clearance Ground plane (back side) (no ground plane) 3mm Ceramic RF Antenna Module 3mm 50ΩTransmission Line Solder Land Pattern for Antenna Figure Remark Dimensions L 17.00 � 0.10 mm L C C W 14.40 � 0.10 mm S1 S1 F Feed pad 1.00 � 0.10 mm F S2 W C 0.90 � 0.10 mm S1 Mount pad 1.40 � 0.10 mm S1 S1 S2 1.00 � 0.10 mm Mount pad Print date 02/10/16 R&D Preliminary use only Mar. 13, 02 Oct. 14, 02 Multilayer Ceramic Antenna 4311 119 00087 (LP Mode) for 850~950MHz AN0870000716141B Grant/Cliff. Oct. 14, 02 sheet 190-2 A4 Page 2 spec.doc PHYCOMP Ltd. MECHANICAL DATA Figure Dimension Port L - 16.5±0.5mm s1 s1 s1 s2 s2 s2 s1 s1 s1 W - 14.0±0.5mm s1 s1 s2 s2 s1 s1 T - 0.9±0.2mm C C F Feed termination 2.1±0.25mm C - 1.0±0.3mm L L S1 Solder termination 1.70±0.35mm S2 Solder termination C C 2.1±0.25mm w w T T s1 s1 Fs Fs11 s1 s1 s1 s1 s1 s1 F F F Radiation Pattern Polar plot -180 -180 -135 -225 -135 -225 -90 -270 -90 -270 -45 45 -45 45 0 0 H Plane E Plane Print date 02/10/16 R&D Preliminary use only Mar. 13, 02 Oct. 14, 02 Multilayer Ceramic Antenna 4311 119 00087 (LP Mode) for 850~950MHz AN0870000716141B Grant/Cliff. Oct. 14, 02 sheet 190-3 A4 Page 3 spec.doc PHYCOMP Ltd. Return Loss Signal DEMO Board 90 mm 25 mm 50 ohm transmission line Print date 02/10/16 R&D Preliminary use only Mar. 13, 02 Oct. 14, 02 Multilayer Ceramic Antenna 4311 119 00087 (LP Mode) for 850~950MHz AN0870000716141B Grant/Cliff. Oct. 14, 02 sheet 190-4 A4 Page 4 spec.doc PHYCOMP Ltd. RELIABILITY DATA (Reference to IEC Specification) IEC IEC 384-10/ 6006868-2 TEST PROCEDURE REQUIREMENTS CECC 32 TEST 100 METHOD CLAUSE 4.4 Mounting The antenna can be No visible damage mounted on printed- circuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive 4.5 Visual inspection Any applicable method In accordance with and dimension specification (no chip using � 10 check off 3 mm) magnification 4.6.1 Antenna Central Frequency Standard test board o in page 4 at 20 C 4.8 Adhesion A force of 5 N applied No visible damage for 10 s to the line joining the terminations and in a plane parallel to the substrate 4.9 Bond strength of Mounted in accordance No visible damage plating on end face with CECC 32 100, paragraph 4.4 Conditions: bending No visible damage 0.25 mm at a rate of 1mm/s, radius jig. 340 mm,1 mm warp on FR4 board of 90 mm length Print date 02/10/16 R&D Preliminary use only Mar. 13, 02 Oct. 14, 02 Multilayer Ceramic Antenna 4311 119 00087 (LP Mode) for 850~950MHz AN0870000716141B Grant/Cliff. Oct. 14, 02 sheet 190-5 A4 Page 5 spec.doc PHYCOMP Ltd. IEC IEC 384-10/ 6006868-2 TEST PROCEDURE REQUIREMENTS CECC 32 TEST 100 METHOD CLAUSE 4.10 Tb Resistance to The terminations 260 � 5 �C for 10 � 0.5 s soldering heat in a static solder bath shall be well tinned after recovery and Central Freq. Change � 6% Resistance to Using visual 260 � 5 �C for 30 � 1 s leaching in a static solder bath enlargement of � 10, dissolution of the termination shall not exceed 10% 4.11 Ta Solderability Zero hour test, and test The termination must be well tinned, at after storage (20 to 24 months) in original least 75% is well atmosphere; un-mounted tinned at termination chips completely immersed for 2 � 0.5 s in 235 � 5�C. 4.12 Na Rapid change of -55 �C (30 minutes) to No visible damage temperature Central Freq. Change +125 �C (30 minutes); 5 � 6% cycles 4.14 Ca Damp heat No visible damage 500 � 12 hours at 60 �C; 2 hours recovery 90 to 95 % RH Central Freq. Change � 6% 4.15 Endurance No visible damage 500 � 12 hours at 125 2 hours recovery �C; Central Freq. Change � 6% Print date 02/10/16 R&D Preliminary use only Mar. 13, 02 Oct. 14, 02 Multilayer Ceramic Antenna 4311 119 00087 (LP Mode) for 850~950MHz AN0870000716141B Grant/Cliff. Oct. 14, 02 sheet 190-6 A4 Page 6 spec.doc PHYCOMP Ltd. ORDERING INFORMATION: 12NC Ordering Code The antennas may be ordered by using the 12 NC ordering code. These code numbers can be determined by the following rules: 4311 1 19 00 087 F C M S T A F. Family Code C. Packing Type Code 43 = Antenna 13 = Bulk, 1000 pcs 11 = 1000 pcs in tape M. Materials Code 1 = High Frequency Material S. Size Code 19 = 16.5 * 14 * 0.9 mm T. Tolerance 00 = 80 M Hz Band Width A. Working Frequency 087 = 850~950MHz Example: 12NC 4311 119 00087 Product description: Antenna (43) by 1000 pcs (11) of High Frequency Material (1), Size 16.5*14*0.9 mm (19); Tolerance (00) of 80 MHz (VSWR<2) Working Frequency (087) = 870~950MHz ORDERING INFORMATION: Method II- by Clear Text Code (Temporary) The antennas may be ordered by using the 16-digit clear text ordering code. These code numbers can be determined by the following rules: AN0870000716141B (Clear Text Code Example) AN 0870 00 07 1614 1 B Product Central Freq. Bandwidth Material Size Quantities Packing AN= 0870=870MHz 00= 80MHz 07=K7 1614=16*14* 1 = 1K B = Bulk Antenna ~ 950MHz 0.9 mm Print date 02/10/16 R&D Preliminary use only Mar. 13, 02 Oct. 14, 02 Multilayer Ceramic Antenna 4311 119 00087 (LP Mode) for 850~950MHz AN0870000716141B Grant/Cliff. Oct. 14, 02 sheet 190-7 A4 Page 7 spec.doc PHYCOMP Ltd. Revision Control: Revision Date Content Remark March 13, 2002 New Issued Oct. 14, 2002 Modify dimension and termination width (S1, F, C, S2) Print date 02/10/16 R&D Preliminary use only Mar. 13, 02 Oct. 14, 02 Multilayer Ceramic Antenna 4311 119 00087 (LP Mode) for 850~950MHz AN0870000716141B Grant/Cliff. Oct. 14, 02 sheet 190-8 A4 Page 8 spec.doc PHYCOMP Ltd.
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the 4311-119-00087 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods