Manufacturers
SCEPTRE PXX2410AW
Description
Sceptre PXX2410AW Adapter - 8W-25W, 5VDC-24VDC PXX AC Interchangeable Wallplug External Power Supply, Adapter
Part Number
PXX2410AW
Price
Request Quote
Manufacturer
SCEPTRE
Lead Time
Request Quote
Category
PRODUCTS - P
Specifications
Burn In
The power supply shall withstand a minimum of 4 hours Burn-In test under full load at 35? ~40? room temperatue, after test, product shall operate normally.
Component Derating
Semiconductor junction temperatures shall not exceed the manufacturer’s maximum thermal rating
Dropping (packed)
1 corner, 3 edges, and 3 surfaces (Height: 1m)
Efficiency
81.7% minimum at input (115Vac to 230Vac) and rated output Load. International Efficiency Level V
Hazardous Substances
The components and materials used shall be compliant with EU Directive 2003/95/EC “RoHS”
Hold Up Time
10 ms minimum at 115Vac/60Hz input at maximum load, and 20 ms minimum at
Input Current
0.600Arms maximum at the rated inputvoltage range and rated DC output load.
Input Frequency
Nominal: 50 to 60 Hz., Range: 47 to 63 Hz.
Input Voltage
Nominal: 100 to 240 Vac., Range: 90 to 264 Vac.
Inrush Current
50Amps maximum at 100-240Vac input, cold start with rated DC output load
Operating Temperature
0 °C to 40 °C, at full load operation
Output Transient Response
The power supply shall maintain outputtransient response time within 800mV with a loading current change from 20% to 80% of maximum current and 0.5A/µs rise up /down test at end of output terminal.
Output Voltage
22.8V~25.2V no load, 22.8V~25.2V full load
Over-Current Protection
The adaptor must have a current limiting function on the output voltage. In overload mode, the output must drop to a low voltage.
Over-Voltage Protection
Over-voltage protection shall be included in the adaptor circuit. A single component failure must not cause an over voltage.
Relative Humidity
10% @ 0 °C & 90% @40 °C
Reliability
When the power supply is operating withinthe limits of this specification,
Ripple And Noise
Ripple and noise levels are measured at 20MHz bandwidth limit with parallel capacitors (10uF and 0.1uF) connecting across the output of power supply.
Short-Circuit Protection
The adaptor must withstand a continuousshort circuit on the output without damage.
Stand By Power
The input power should be less than 0.3W with no load
Storage Temperature
-30 °C to 70 °C without package
Turn On Delay
During turn on and turn off, no output voltage shall exceed its nominal voltage by more than 10% and no output shall change its polarity with respect to its return line. All outputs shall reach their steady state values within 3 seconds of turn on.
Features
- Application: charger, power source for instruments, computer peripherals, and consumer electronics, etc
- CE/FCC/CTICK/PSE and CCC compliant
- Efficency IV/V
- EMI: EN55022
- EMS: IEC 61000-4-2/3/4
- Input 90~264Vac
- Output 5Vdc-24Vdc
- Overvoltage,overload and short-circuit protection
- UL1310 and UL60950-1, CSA/TUV to EN60950-1 approvals
- US, Europ, UK and Australia AC prong available
Datasheet
Extracted Text
GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com Customer: Customer Model Number: Product Part Number: PXX2410AW 1. SCOPE: Purpose of this document is to specify the functional requirements of the 24W wall mounted AC-DC switching power supply with exchangeable AC input prong. 2. INPUT CHARACTERISTICS: 2.1 Input Voltage: Nominal: 100 to 240 Vac. Range: 90 to 264 Vac. 2.2 Input Frequency: Nominal: 50 to 60 Hz. Range: 47 to 63 Hz. 2.3 Input Current: 0.600Arms maximum at the rated input voltage range and rated DC output load. 2.4 Inrush Current: 50Amps maximum at 100-240Vac input, cold start with rated DC output load @ 25 °C ambient temperature. 2.5 Stand By Power The input power should be less than 0.3W with no load 3. OUTPUT CHARACTERISTICS: 3.1 Power Voltage Min.Load Max.load Peak Output Power 24Vdc 0A 1000mA - 24W 3.2 Output Voltage 22.8V~25.2V no load 22.8V~25.2V full load DWG Control Number: 91-0240XX-19 Revision: 2 Date: 12/07/11 Page 1 of 7 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 3.3 Ripple And Noise: Ripple and noise levels are measured at 20MHz bandwidth limit with parallel capacitors (10uF and 0.1uF) connecting across the output of power supply. Voltage Ripple And Noise (Max.) 24Vdc 150mVp-p 3.4 Turn On Delay During turn on and turn off, no output voltage shall exceed its nominal voltage by more than 10% and no output shall change its polarity with respect to its return line. All outputs shall reach their steady state values within 3 seconds of turn on. 3.5 Hold Up Time 10 ms minimum at 115Vac/60Hz input at maximum load, and 20 ms minimum at 230Vac/50Hz input at maximum load. 3.6 Output Transient Response The power supply shall maintain output transient response time within 800mV with a loading current change from 20% to 80% of maximum current and 0.5A/µs rise up /down test at end of output terminal. 3.7 Efficiency: 81.7% minimum at input (115Vac to 230Vac) and rated output Load. International Efficiency Level V 3.8 Output connector specification: Please see our website www.gpelectronics.com 3.9 Hazardous Substances The components and materials used shall be compliant with EU Directive 2003/95/EC “RoHS” 4. PROTECTION REQUIREMENT: 4.1 Over-Voltage Protection Over-voltage protection shall be included in the adaptor circuit. A single component failure must not cause an over voltage. 4.2 Over-Current Protection The adaptor must have a current limiting function on the output voltage. In overload mode, the output must drop to a low voltage. 4.3 Short-Circuit Protection The adaptor must withstand a continuous short circuit on the output without damage. DWG Control Number: 91-0240XX-19 Revision: 2 Date: 12/07/11 Page 2 of 7 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 5. ENVIRONMENTAL REQUIREMENT: 5.1 Operating Temperature: 0 °C to 40 °C, at full load operation 5.2 Storage Temperature: -30 °C to 70 °C without package 5.3 Relative Humidity: 10% @ 0 °C & 90% @40 °C 5.4 Dropping (packed): 1 corner, 3 edges, and 3 surfaces (Height: 1m) 5.5 Reliability: When the power supply is operating within the limits of this specification, the MTBF will be approximately 100,000 hours @ 25° C 5.6 Burn In: The power supply shall withstand a minimum of 4 hours Burn-In test under full load at 35℃ ~40℃ room temperatue, after test, product shall operate normally. 5.7 Component Derating: Semiconductor junction temperatures shall not exceed the manufacturer’s maximum thermal rating 6. SAFETY APPROVAL: 6.1 Item Standard DWG Control Number: 91-0240XX-19 Revision: 2 Date: 12/07/11 Page 3 of 7 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 6.2 Dielectric Strength (Hi-Pot): Primary to secondary, 4242 Vac/3.5mA 1 minute for type test, 3 seconds for product. 6.3 Insulation Resistance: Input to output: 10MOhms min. at 500Vdc 6.4 Leakage Current: The leakage current shall be less than 0.25mA for Class II when the power supply is operated maximum input voltage and maximum frequency. 7. EMC STANDARDS 7.1 EMI Standards The power supply shall meet the radiated and conducted emission requirements for FCC PART 15 CLASS B, EN55022 CLASS B, J55022 7.2 EMS Standards The power supply shall meet the following EMS standards 7.2.1 IEC61000-4-2 Electrostatic Discharge (ESD) Static – discharge test by contract or air should be conducted with Static – discharge teeter, energy storage capacitance of 150pF, and discharge resistance of 330Ω. 8KV air discharge, 4KV contact discharge, Performance Criterion B. 7.2.2 IEC61000-4-3 Radiated Electromagnetic Fields(RS) Radio- frequency Electromagnetic Field Susceptibility Test, RS, 80- 1000MHz,3V/m, 80%AM(1KHz), Performance Criterion A. 7.2.3 IEC61000-4-4 Electrical Fast Transient / Burst (EFT) Power Line to Line: 1KV Performance Criterion B. 7.2.4 IEC61000-4-5 Lightning Surge Attachment Lightning Surge voltage of differential and common modes shall be applied across AC input lines and across input and frame ground. Power Line to Line: 1KV Line to Earth : Performance Criterion B. 7.2.5 IEC61000-4-6 Conducted Radio Frequecy Disturbances (CS) Conducted Radio Frequency Disturbances Test, CS, 0.15-80 MHz, 3V/m, 80%AM, 1KHz, Performance Criterion A. DWG Control Number: 91-0240XX-19 Revision: 2 Date: 12/07/11 Page 4 of 7 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 7.2.6 IEC61000-4-11 Voltange Dips/Short Interruption/Variaions Voltage Dips, 30% reduction- 10ms, Performance Criterion B, 60% Reduction – 100ms, Performance Criterion C, Voltage Interruptions>95% Reduction- 5000ms, Performance Criterion C 8. MECHANICAL REQUIREMENT: 8.1 Enclosure: Adaptor dimension in millimeter (mm): L: 81 x W: 49 x H: 34 8.2 Input Connector: - Detachable wall mounted input prong - Four types of interchangeable AC input prong: UL, UK, SAA, VDE - Refer to section AC Prong Mechanical Drawing for more information DWG Control Number: 91-0240XX-19 Revision: 2 Date: 12/07/11 Page 5 of 7 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com MECHANICAL DRAWING (Dimensions in mm) Output cord AWG#20 DWG Control Number: 91-0240XX-19 Revision: 2 Date: 12/07/11 Page 6 of 7 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com OUTPUT CONNECTOR: BARREL, CENTER POSITIVE FEMALE, WITH 2.5MM AND 2.1MM INNER DIAMETER ARE STANDARD PARTS FROM FACTORY. PLEASE REFER TO PRODUCT CATALOG OR “OUTPUT CONNECTOR” LINK ON WEBSITE, WWW.SCEPTREPOWER.COM, FOR MORE OPTIONS OF CONNECTORS. NAMEPLATE: DWG Control Number: 91-0240XX-19 Revision: 2 Date: 12/07/11 Page 7 of 7
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the PXX2410AW have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
Sceptre PDR-12100A Power Supply - Easy mounting (one-step Installation), Separation of AC and DC. Ex...
Request a Quote
The quote request has been received
Close
Facing challenges or have inquiries? Feel free to contact us!
Call Us +1-469-283-2440
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods