GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com Customer: Customer Model Number: Product Part Number: PB-1295A 1. SAFETY STANDARD The power supply shall be certified by the following international regulatory standards: Country Certified Status Standard UL USA Approved UL 60950-1 CUL Canada Approved CSA C22.2 NO. 60950-1 CE Europe Approved Declared & CE Mark FCC USA Test to Comply FCC, Part 15, Class B 2. DIELECTRIC WITHSTANDING STRENGTH (HI-POT) Primary to Secondary DC2121V, 10mA, 1 minute for type test, 3 seconds for production. 3. INPUT FEATURE 3.1 INPUT RATED VOLTAGE: 100VAC to 240VAC 3.2 INPUT VOLTAGE RANGE: 90VAC to 264VAC. 3.3 INPUT FREQUENCY RANGE: 50Hz to 60Hz. 3.4 INPUT CURRENT: 2.0Amax o 3.5 INRUSH CURRENT: 150Amax. at 100-240VAC input for a cold start at 25 C 3.6 EFFICIENCY: higher than 87%, @ 115/230VAC, 50/60Hz input and full load output, complies to International Efficiency Level V 3.7 NO LOAD POWER CONSUMPTION: less than 0.5W @ 115/230VAC, 50/60Hz input DWG Control Number: 91-1500XX-03 Revision: 1 Date: 07/14/11 Page 1 of 6 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 4. OUTPUT FEATURE RATED OUTPUT SPEC. LIMIT REMARK 12Vdc Min. value Max. value Output Regulation 11.4V 12.6V 12V + 5% Output Load 0.00A 9.5A 20MHz Bandwidth 10uF Ripple and Noise - 200mV Ele.Cap.+0.1uF Cer. Cap. No Load Input Power - 0.5W Input 115-230Vac PFC 0.90 - At the full load 100-240Vac Output Overshoot - 10% Turn-on delay time - 3S Hold up time 10mS/20mS - 115VAC, 60Hz/230VAC, 50Hz Transient response - - 5. PROTECTION FEATURE 5.1 OVER - CURRENT PROTECTION: The power supply shall be hiccupped when any output operating in overload condition under any line condition for an indefinite period of time. The power supply shall be self-recovered when the fault condition is removed. 5.2 OVER - VOLTAGE PROTECTION: The power supply shall be protected when output voltage reaches its over voltage trigger point. The power supply shall be self-recovered when the fault condition is removed. 5.3 SHORT - CIRCUIT PROTECTION: The power supply shall be hiccupped and no damage shall occur when any output operating in a short circuit condition under any line condition for an indefinite period of time. The power supply shall be self-recovered when the fault condition is removed. DWG Control Number: 91-1500XX-03 Revision: 1 Date: 07/14/11 Page 2 of 6 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 6. ENVIRONMENTAL CONDITIONS 6.1 OPERATING The power supply shall be capable of operating continuously in any mode without performance deterioration in the following environmental conditions. 6.1.1 Operating Temperature: Operating Maximum Coefficient of Temperature Power Output De-rating Power o o ( C) (W) (W/ C) 0 to 25 114 0 25 to 30 114 ~112 0.40 30 to 40 112 ~ 98 1.40 40 to 70 98 ~ 65 1.10 6.1.2 Relative Humidity: 10% ~ 90% 6.1.3 Vibration: 1.0mm, 10–25Hz, 15 minutes per cycle for each axis (X, Y, Z) 6.1.4 Cooling: The power supply will operate with convection cooling. Blocking of vents must not cause damage to the power supply. 6.2 NON – OPERATING The power supply shall be capable of withstanding the following environmental conditions for extended periods of time, without sustaining electrical or mechanical damage and subsequent operational deficiencies. o o 6.2.1 Ambient Temperature: -30 C ~ 70 C 6.2.2 Relative Humidity: 10% ~ 90% 6.2.3 Vibration and Shock The power supply shall be designed to withstand normal transportation vibration per MIL–STD-810D, method 514 and procedures X, as it is mounted in the chassis assembly and packed for shipping 7. EMC STANDARDS 7.1 EMI STANDARDS The power supply shall meet the radiated and conducted emission requirements for FCC PART 15, EN55022 CLASS B. DWG Control Number: 91-1500XX-03 Revision: 1 Date: 07/14/11 Page 3 of 6 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 7.2 EMS STANDARDS The power supply shall meet the following EMS standards: 7.2.1 IEC61000-4-2 Electrostatic Discharge (ESD) Static – discharge test by contract or air should be conducted with Static – discharge teeter, energy storage capacitance of 150pF, and discharge resistance of 330Ω. 8KV air discharge, 4KV contact discharge, Performance Criterion B. 7.2.2 IEC61000-4-3 Radiated Electromagnetic Fields(RS) Radio- frequency Electromagnetic Field Susceptibility Test, RS, 80- 1000MHz,3V/m, 80%AM(1KHz), Performance Criterion A. 7.2.3 IEC61000-4-4 Electrical Fast Transient / Burst (EFT) Power Line to Line: 1KV Performance Criterion B. 7.2.4 IEC61000-4-5 Lightning Surge Attachment Lightning Surge voltage of differential and common modes shall be applied across AC input lines and across input and frame ground. Power Line to Line: 1KV Line to Earth : 2KV Performance Criterion B. 7.2.5 IEC61000-4-6 Conducted Radio Frequecy Disturbances (CS) Conducted Radio Frequency Disturbances Test, CS, 0.15-80 MHz, 3V/m, 80%AM, 1KHz, Performance Criterion A. 7.2.6 IEC61000-4-11 Voltange Dips/Short Interruption/Variaions Voltage Dips, 30% reduction- 10ms, Performance Criterion B, 60% Reduction – 100ms, Performance Criterion C, Voltage Interruptions>95% Reduction- 5000ms, Performance Criterion C 8. RELIABILITY AND QUALITY CONTROL 8.1 MTBF When the power supply is operating within the limits of this specification the o MTBF shall be at least 50,000 hours at 25 C (MIL-STD-217F). DWG Control Number: 91-1500XX-03 Revision: 1 Date: 07/14/11 Page 4 of 6 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 8.2 BURN-IN The power supply shall under go a minimum of 4 hours Burn-In test under full o o load at 35 C ~ 40 C. 8.3 COMPONENT DERATING Semiconductor junction temperatures shall not exceed the manufacturer’s maximum thermal rating. 9. WEIGHT The weight of the power supply shall be about 735g. 10. INSULATION RESISTANCE Input to output: 10M OHM(500VDC) 11. LEAKAGE CURRENT The leakage current shall be less than 3.5 mA for Class I when power supply is operated under maximum input voltage and maximum load conditions. 12. ENVIRONMENT-RELATED SUBSTANCES Complies to EU Directive 2002/95/EC “RoHS” 13. MAJOR MEASURE EQUIPMENT A. AC SOURCE AFC-500W □ B. POWER METER : Zentech 2100 □ C. ELECTRONIC LOAD: PRODIGIT 3310C □ D. OSCILLOSCOPE: Lecroy LT354 □ E. DIGITAL MULTIMETER: Fluke 45 □ F. DC POWER: WYK-603 □ G. HI-POT TESTER: GOODWILL GPT-605 □ H. HYBRID RECORDER: YOKOGAWA DR130 □ I. CONS. T/H SIMULATOR: TH-A4H 1-150 □ J. INSULATION RESISTANCE TESTER: EXTECH-7620 □ DWG Control Number: 91-1500XX-03 Revision: 1 Date: 07/14/11 Page 5 of 6 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com Mechanical Specification: (C14 inlet for PB-series; optional C6 inlet for PBD-series) Note: 1. Dimension are shown in mm. 2. DC CORD: AWG#14, UL1571, Length: 1000mm +/- 1% 3. Weight: 735gs approx 4. Optional output connector: PLEASE REFER TO PRODUCT CATALOG OR “OUTPUT CONNECTOR” LINK ON WEBSITE, WWW.SCEPTREPOWER.COM, FOR MORE OPTIONS OF CONNECTORS. DWG Control Number: 91-1500XX-03 Revision: 1 Date: 07/14/11 Page 6 of 6