GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com Customer: Customer Model Number: Product Part Number: PS-12100A 1. INTRODUCTION: PS-12100A is a single output, 120 watts continuous, desktop switching power supply for information technology equipment. 2. ELECTRICAL CHARACTERISTICS: 2.0. Input Characteristics: 2.0.1. Operating Input Voltage Range: Range of input voltage is from 90 to 260VAC 2.0.2. Input frequency range: Input frequency is between 47-63Hz. 2.0.3. Input Current: Input AC Current @90V with rated output load <= 2.5A 2.0.4. Inrush current: Inrush current will not exceed 100A at 230VAC input, cold start, 25°C. 2.1. Output Characteristics: 2.1.1. Output Range: Output LOAD RANGE Load Ripple & Voltage Min. Typ. Max. Regulation Noise(max) +12 VDC 0 A A 10.0 A ± 5 % 180 mVp-p 2.1.2. Line regulation: Line regulation is less the 2% while measuring at rated load and +/- 10% of input voltage variation. 2.1.3. Ripple Test condition: 2.1.3.1. All voltage measured at the output connector, which should be connected with a 47uF capacitor. 2.1.3.2. The ripple is measured from peak to peak with a bandwidth-limit of 20MHz and at the output terminals of the power supply with a 0.1uF ceramic disk capacitor. 2.1.4. No Load Regulation: +/- 5% 2.1.5. Continuous output power: 120W max. DWG Control Number: 91-1200XX-0X Revision: 1 Date: 07/23/09 Page 1 of 1 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 2.2. General features: 2.2.1. Efficiency: Efficiency is at least 85%~88% while measuring at nominal line and rated load. CEC IV Efficiency Regulations Compliance 2.2.2. Hold-up time: Hold-up time is longer than 75mS at nominal line (110VAC) input at rated load, which is measured from the end of the last charging pulse to the 95% drops of the main output voltage. 2.3. Protection: 2.3.1. Over-voltage protection: Over-voltage protection is available on output, if the output (12V) reaches an Over-voltage condition the output shall be shut down. The output will be restored after the removal of over voltage condition. 2.3.2. Short circuit protection: In a short circuit condition, the output will be shut down. The output will be restored after removal of short circuit condition. 2.3.3. Over-load protection: Over-load at the output will not cause damage the adapter; the output will be shut down. The output will be restored after the removal of the overload condition. 2.4. Insulation: 2.4.1. Dielectric strength: From input live and neutral to output should be 4242VDC for 2 seconds (trip current 5mA). From input live and neutral to output should be 2121VDC for 2 seconds (trip current 5mA). 2.4.2. Leakage current: Leakage current flowing from input to output or any external accessible parts will be less than 0.75mA for any admitted value of line voltage. 3. SAFETY AND ELECTROMAGNETIC COMPATIBILITY: Safety requirements: • U.L.60950-1 • C.S.A C22.2 – 60950-1 • TUV EN60950-1 • CE declaration of conformity. Radiated and conducted electromagnetic interference compliance: � FCC Part15, class B � CISPR-22, Class B � EN 55022, class B DWG Control Number: 91-1200XX-0X Revision: 1 Date: 07/23/09 Page 2 of 2 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com 4. ENVIRONMENT CONDITIONS: 4.0. MTBF specified at 25°C ambient temperature and with nominal load, according to MIL-217F:100,000 Hours or above. 4.1. The adapter must be able to withstand the following environment Operating conditions: • Temperatures: 0°C to +35°C • Relative humidity (without condensation): 10% to 95% Storage conditions: • Temperatures: -20°C to +85°C • Relative humidity (without condensation): 5% to 95% 5. MECHANICAL CHARACTERISTICS: 5.0. Connections: 5.0.1. Input connector : IEC-320-C14 inlet 5.0.2. Output Connector assignment: Refer to product catalog for different options. 5.1. Construction: Desktop enclosure plastic case is shown under mechanical drawing. 5.2. Weight: Approximately 620 grams. DWG Control Number: 91-1200XX-0X Revision: 1 Date: 07/23/09 Page 3 of 3 GOLDEN PACIFIC ELECTRONICS, INC. 560 South Melrose Street Placentia, CA 92870 www.gpelectronics.com Mechanical Drawing: Color: Black Unit: mm Notes: BARREL, CENTER POSITIVE FEMALE, WITH 2.5MM AND 2.1MM INNER DIAMETER ARE STANDARD PARTS FROM FACTORY. PLEASE REFER TO PRODUCT CATALOG OR “OUTPUT CONNECTOR” LINK ON WEBSITE, WWW.SCEPTREPOWER.COM, FOR MORE OPTIONS OF CONNECTORS. DWG Control Number: 91-1200XX-0X Revision: 1 Date: 07/23/09 Page 4 of 4