8 EPC-2102 SBC (P5000HX2(-M)) Quick Reference Card This card provides information to help you quickly configure, install, and operate your single-board computer. Keep this card in a convenient location for future use. See the service manual for more detailed information. Front of Switch Block EIDE HDD FDD 2 2 40 34 Closed 1 39 1 33 Open SCSI 1-4 1-3 1-2 1-1 JP3 35 68 IDE/SCSI Activity LED Real-Time Clock with Battery +- 1 34 JP2 SIMM 4 Bank 1 SIMM 3 Serial Port 2 SIMM 2 2 10 Bank 0 SIMM 1 1 9 L2 Cache Serial Port 1 5 9 Pentium Processor with Heatsink 6 1 Parallel Port 1 14 Auxiliary CPU Fan USB JP6 JP9 JP5 JP4 JP7 0 1 - + - 1 1 JP8 JP10 44 25 13 PS/2 Mouse Keyboard 1 2 Reset 910 Ground Not Connected Keyboard Clock Keyboard Data 1 Keyboard Lock +5 V Out 007-01146-0001 © RadiSys Corporation Speaker May 2001 All Rights Reserved Specifications subject to change without notice Printed in USA   Technical and Product Support Jumper Settings Setup Utility Accessing the Web Site Setup Item Default Setting JP9 JP10 Host Bus Speed In-depth printable service manuals and other documentation are Floppy Controller Enabled available for download from the RadiSys Web site: None 1—2 66.6MHz Diskette A / B 3½” 1.44 MB;Not Installed http://www.radisys.com 1—2 None 60.0MHz Floppy Seek during POST Enabled Then click on Support to access a link to the documentation, 1—2 1—2 50.0MHz drivers, and BIOS. Documentation is available at this Web site in IDE Controller Setup Primary (1F0-1F7h) ® ® Adobe Acrobat .PDF format and may be viewed and printed Auto Detect IDE Drives Enabled Bus Core CPU ® ™ using Acrobat JP6 JP8 Reader software. BIOS files are available as self- † ‡ Ratio Speed Large Disk DOS Compatible Enabled extracting disk image files. Links are provided to various partners’ web sites where any files and tools needed to install drivers are None None 2/3 100 MHz Keyboard Typematic Sound Enabled available for download. None 1—2 1/2 133 MHz Keyboard Typematic Rate / Delay 30 chars/sec; 250 msec Calling Technical Support 1—2 1—2 2/5 166 MHz 101-Key Keyboard NumLock at Boot Disabled RadiSys Corporation provides technical support Monday–Friday, 1—2 None 1/3 200 MHz Set Boot Drive Sequence Diskette Drive 8:00 a.m.–5:00 p.m. Central Time in the continental USA and 8:30 a.m.–5:00 p.m. in Europe. None None 1/5 233 MHz Report POST Errors Enabled To expedite your request, have the RadiSys product model and Report Option ROM Errors Enabled serial number available. Then call one of the following numbers: Serial 2 Configuration JP2, Show F2 Message for Setup Enabled • Inside the continental USA, dial 1-800-627-8700. JP3, 2—3 RS-232 Quiet Boot Enable/Disable Disabled Outside the continental USA, dial 1-713-541-8200 (add long &JP5 1—2 RS-422 distance/international codes). Password Options Disabled In Europe, dial +31-36-5365595. 16550 Compatible UART 1 03F8h IRQ 4 Watchdog Timer Inspection of Contents / Packaging of Product 16550 Compatible UART 2 02F8h IRQ 3 JP4 2—3 Inactive The packaging for this product has been tested to assure that it will Select Parallel Port Address 0378h IRQ 7 withstand responsible handling by the carrier. 1—2 Active Parallel Port Mode AT Compatible Caution: Inspect contents immediately and file a claim with the carrier for any damage. Save the shipping box and packaging Next Step OS Configuration Serial Redirection Destination Disabled material to use for any further shipment of this equipment. Serial Redircetion BAUD Rate 56000 JP7 2—3 Normal Operation However, if the packaging is damaged and is not suitable for shipment, call RadiSys Technical Support to obtain new packaging. External Cache Disabled 1—2 Next Step OS optimization The warranty may be void if the product is returned using DRAM Speed 70 ns † unapproved or damaged original packaging. The Bus Core Ratio is based on the Host Bus Speed at 66.6MHz. ‡ DMA Aliasing Disabled The default CPU speed is determined by the processor installed. Returning Your Product ECC/Parity Config Parity A Returned Material Authorization (RMA) number must be written on the outside of the shipping carton of all equipment returned to Memory Gap Block Size Disabled Switch Settings RadiSys for service and/or repair. It is recommended that any Gap Reporting to OS Enabled correspondence included with the carton contents also refer to the Default Monitor Type RMA number. 8 / 16-Bit I/O Recovery Time 4.5 SYSCLOCK SW1-1 Open Monochrome Note: The factory will refuse the shipment if it is sent freight collect ISA Guaranteed Access Time Disabled or if it does not display an RMA number. Closed Color Delayed Transactions Enabled On-Board ROM Access Quick Start ISA Bus Speed 8.25 MHz (based on Host Bus Speed) To begin operating your EPC-2102 single-board computer, perform Open Flash memory enabled; Speaker Config Enabled SW1-2 auxiliary ROM disabled the following: Watchdog Timer Delay 1.2 sec 1. Ensure that all jumper settings match your requirements Closed Flash memory disabled; Allocate USB Resources Disabled 2. Ensure that all switch settings match your requirements. auxiliary ROM enabled 3. Install the SBC onto a passive backplane in a chassis. PS/2 Mouse Config Disabled CMOS RAM 4. Attach all necessary peripheral devices to the appropriate PCI IRQ Line 1 IRQ 9 headers and connectors on the SBC. SW1-3 Open Normal operation PCI IRQ Line 2 IRQ 10 5. Power-on the system. Closed Factory default CMOS values are loaded 6. Run the Setup Utility if you need to change any settings to PCI IRQ Line 3 IRQ 11 match your requirements. Configuration Ports PCI IRQ Line 4 IRQ 15 Note: See the table “Setup Utility” for factory default settings.. SW1-4 Open Map ports to I/O address 270/271 Delay for PCI Config Disabled To avoid damage or injury, always exercise the following Closed Map ports to I/O address 370/371 PCILatency for Bus 0Devices 0Dh-14h Auto precautions when handling the equipment: Use a grounding wrist strap or other static-dissipating device PCI Cache Line Size Auto Default settings are shown in italics Power-off the system � Onboard PCI SCSI Disabled Disconnect all power cords