L5000HX Series SBC QuickReference Card This card provides information to help you quickly configure, install, and operate your Single Board Computer. Keep this card in a convenient location for future use. See the User’s Manual for more detailed information. Front of Switch Block EIDE 1-1 1-2 1-3 1-4 2 40 Open Closed 1 39 FDD 2 34 Serial 2 IDE Activity 1 33 LED 1 2 SIMM 1 9 10 Bank 0 Serial 1 SIMM 2 Speaker 5 9 L2 Cache 6 1 Parallel Pentium Processor 1 with Heatsink 14 25 13 JP5 Battery 1 JP4 JP8 JP3 Keyboard JP1 JP2 Speaker +5V Out JP6 Keyboard Lock Keyboard Data Keyboard Clock Not Connected Ground Reset 1 29095B ©Texas Micro Inc. April 1998 All Rights Reserved Specifications subject to change without notice Printed in USA Primary Secondary QuickStart Jumper Settings Setup Utility JP8B JP8D Setup Item Default Setting To begin operating your L5000HX series SBC, perform the following: Diskette A / B 1.44 MB 3½”; Not Installed 1. Ensure that all jumper settings match your requirements IDE Adapter Type Auto (all 4 possible drives) 2. Ensure that all switch settings match your requirements B1 B2 D1 D2 D3 Write Precomp None 3. Install the SBC onto a passive backplane in a chassis Multi-Sector Transfers Disabled A1 A2 C1 C2 C3 4. Attach all necessary peripheral devices to the appropriate headers LBA Mode Control Enabled on the SBC 32-Bit I/O Disabled 5. Attach all necessary peripheral devices to the appropriate connectors JP8A JP8C on the SBC Transfer Mode Standard Pins on JP8 Jumper Block 6. Power-on the system Video System EGA/VGA JP8A JP8B Host Bus Speed 7. Run the Setup Utility if you need to change any settings to match your External Cache Enabled requirements None B1—B2 66.6MHz Cache System / Video BIOS Area Enabled See the table “Setup Utility” for factory default settings. Note: Cache C800-DFFF Disabled (all regions) A1—A2 None 60.0MHz To avoid damage or injury, always exercise the following System / Video Shadow Enabled A1—A2 B1—B2 50.0MHz precautions when accessing the interior of the chassis and handling the equipment: Regions w/ Legacy ROMs ROM • Use a grounding wrist strap or other static-dissipating device JP8C JP8D Bus CPU Boot Summary Screen Enabled ‡ • Power-off the system Core Speed • Disconnect all power cords Floppy Check Disabled ! † Ratio Quiet Boot Disabled C2—C3 D2—D3 2/3 100 MHz POST Errors Enabled Technical Support C2—C3 D1—D2 1/2 133 MHz Keyboard Numlock Auto Texas Micro provides technical support Monday through Friday between C1—C2 D1—D2 2/5 166 MHz Key Click Disabled 7:00 a.m. and 6:00 p.m., Central Time, in the Continental USA, and Keyboard Auto-Repeat Rate / Delay 30/sec; 1/2 sec between 8:00 a.m. and 6:00 p.m. in Europe. Serial 1 JP1 JP3 JP4 JP5 Serial 1 Port 3F8 IRQ4 To expedite your request, have the Texas Micro product model and serial RS-232 None 1—2 None None Serial 2 Port 2F8 IRQ3 number available. RS-422 1—2 None 1—2 1—2 LPT Port 378 IRQ7 Step Action Parallel Port Mode Output Only Reserved JP2 JP6 1 • In the USA, dial 1-800-627-8700. Technical Diskette Controller Enabled Outside the Continental USA, dial Do Not Alter 1—2 1—2 Support Local Bus IDE Adapter Both Enabled 713-541-8200 (add long distance/ † The Bus Core Ratio is based on the Host Bus Speed at 66.6MHz. international codes as required). DRAM Speed 70 ns ‡ The default CPU speed is determined by the processor installed. • In Europe, dial +31-36-5365595. DMA Aliasing Enabled 8 / 16-Bit I/O Recovery 4.5 2 Upon answer, press 3 for Technical Support. Switch Settings Memory Gap Disabled Watchdog Timer Status Disabled 1 Dial 713-541-8250, 24 hours a day, 7 BBS SW1-1 Default Monitor Type days a week (add long distance/ Watchdog Timer Delay 1.2 sec international codes as required). Open Monochrome Onboard Speaker On Closed Color 2 Set modem/communications equipment: ISA Guaranteed Access Off Protocol: ANSI SW1-2 On-Board ROM Access ISA Bus Speed PCI Clock 4 Data Bits: 8 Parity: None Open Flash memory enabled; ECC/Parity Config Disabled Stop Bits: 1 Crisis Recovery mode disabled PCI IRQ Line 1 / 2 / 3 / 4 Auto Select (all PCI IRQ’s) Closed Flash memory disabled; 3 When you connect, follow the online Plug & Play O/S No Crisis Recovery mode enabled instructions to download software. Large Disk Access Mode DOS SW1-3 CMOS RAM 1 Dial 713-541-8200 or 800-627-8700, 24 Supervisor / User Password Disabled InfoLine hours a day, 7 days a week (add long Fax Service Open Normal operation Password on Boot Disabled distance/international codes as required). Diskette Access Supervisor Closed Factory default CMOS values are loaded 2 Upon answer, press 190 for the InfoLine Fixed Disk Boot Sector Normal SW1-4 Reserved fax service. System Backup Reminder Disabled Open Do Not Alter 3 Follow the instructions to request Virus Check Reminder Disabled documents. Console Redirect Port Disabled Default settings are shown in italics http://www.texasmicro.com Web Site Console Redirect Baud Rate 9600