DIGITAL FIBER SENSOR FX-100SERIES Conforming to EMC Directive Bringing digital fiber sensors closer New possibilities with digital Ţ ber sensors. The FX series is a round 100 for success. Easy to read, multipurpose, and at an economical price. The FX series has been designed to be what customers want it to be. Take a step into the new world that starts with ‘ ’. 100 Easy to read The digital dual-display shines out in the workplace! The digital dual-display allows you to check both the threshold value and incident light intensity at the same time, and it also makes the procedures for setting the various values much easier. The threshold values can be adjusted simply by pressing the (UP) key or the (DOWN) key, so that the sensors can be used at the same sensitivity levels as analog control-type Incident light intensity Threshold value sensors. And of course a key lock function is also included. General purpose Commercially-available press-Ţ t connectors are used, so that the processing costs for connection cables can be greatly reduced. Commercially-availabie connectors Conventional lead time are used so that lead time and spare Conventional (cable type) part numbers can both be reduced. ;Harness processing by outside order after sensor preparation ss p Customer Sensor preparation Sensor installation The connectors used are commercially- Harness 1 Sensor purchase and preparation Harness Processing available connectors, so that processing 2 Harness processing by outside order 2 processor costs and lead time required for carrying out From now on (built-in connector type) Lead time from now on processing after purchase of the sensors can ;Harness processing by outside order ss p be greatly reduced. The same connection Customer Sensor preparation Sensor installation Reduced parts as the DP-100 series of digital pressure Harness 1 Sensor purchase and preparation Harness Processing sensors and the PM-64 series of micro processor 2 Harness processing by outside order 2 photoelectric sensors can be used. Lead time further reduced Using cables with connectors Reduced lead time Customer Sensor preparation Sensor installation Reduced 1 Purchase of sensors and cable with connectors SUNX Ţ ber sensor product lineup Select the best types to suit your application. FX-300 (High function) FX-410 (Volume setting) Digital type FX-101 (Standard type) FX-100 FX-102 (Long sensing range type) Analog control-type FX-311 (General purpose) 1 Digital fiber sensor DIN rail installation also possible "3.2 "0.126 mounting hole 9 mm Direct installation possible without bracket 0.354 in thickness Designed in a 3-layer structure to accommodate basic settings through to advanced settings. Setting details are divided into three levels for clearer operation, so that settings for normal operation are made in ‘RUN mode’, basic settings are made in ‘SET mode’, and advanced functions are set in ‘PRO mode’. This makes setting operations much easier to understand and carry out. RUN mode Functions used during normal operation [ function table ] RUN MODE • Changing threshold values • Key lock • Quick settings • Code settings Simple setting SET mode Functions used when initializing the sensor and carrying out maintenance [ function table ] • Teaching • L-ON / D-ON setting SET MODE • Timer setting • Light-emitting amount selection • Emission frequency setting function PRO mode Equipped with a full complement of digital fiber sensor functions [ function table ] PRO MODE • Shift • External input • Reset • GETA • ECO • Display reversing • Surplus value display • Copy Special and detailed setting • Threshold value seeking cycle setting The same operating system is shared by the widely-acclaimed Digital pressure sensor DP-100 series of digital pressure sensors. The ‘100’ is the indicator DP-100 series for easy handling. 2 Easy for inexperienced operators to use, and experienced operators will still be satisŢ ed too. Introducing sensors with a full complement of functions to support the needs of your workplace. Changing threshold values Key lock Quick settings Code settings Quick setting numbers (summary) For For For For factory factory designers designers Quick code input function operators operators Light-emitting No. Output operation Timer amount selection Sensor settings can be made simply by selecting preset Dark-ON OFF None values. Dark-ON ONNone Dark-ON OFF OFF-delay 10 ms Dark-ON ON OFF-delay 10 ms Light-ON ON ON-delay 40 ms Light-ON OFF ON-delay 40 ms Light-ON ON ON-delay 10 ms Light-ON OFF ON-delay 10 ms Smooth support via telephone ConŢ rmation can be carried out smoothly via telephone by simply quoting numbers. This can be of great assistance when dealing with overseas customers. 3 Teaching L-ON / D-ON setting Timer setting Light-emitting amount selection Interference prevention function For For For For factory factory Teaching using ON / OFF buttons Light-emitting amount selection function designers designers operators operators Simply press the ON button when an object is present If the light receiving level becomes saturated when sensing and OFF when it is not. There is no need to switch over short distances or when sensing transparent objects settings or make judgments between Light-ON ( ) or minute objects, the light emitting amount can be adjusted and Dark-ON ( ). so that stable sensing can be provided without needing to change the response time. Thru-beam type Emission frequency setting function For For factory factory operators operators ( ) Object present ON Object absent OFF The emission frequencies can be set separately for each unit in order to avoid interference. The emitted light ţ ashes while setting is in progress, so that you can see at a glance which fiber sensor is currently being set. In addition, this interference prevention is not done by using optical Reflective type communication. This means that there is no need to place the ampliŢ ers close together like there was before, and so the ampliŢ ers can be set up apart from each other. mWhen the emission frequencies are changed, the response times will also change. Object present ON Object absent OFF Limit teaching function This carries out teaching and sets threshold values only when no object is present (when the incident light amount is stable). This is useful when sensing objects if there are other objects in the background and when sensing minute objects. Teaching can also be carried out using external input. Shift External input Threshold value seeking cycle setting GETA ECO Display reversing Surplus value display Copy Reset For For factory factory Threshold value seeking cycle setting function External input function operators operators This function seeks changes in the light Settings such as emission (Brown) V Current value emitting amount resulting from changes halt, limit / auto teaching (Black) Output (White) External input in the environment over long periods and ECO settings can be (Blue) 0 V (such as dust levels), so that the incident carried out via external Threshold value light intensity can be checked at desired input. External input lines are equipped as standard intervals and the threshold values can be reset automatically. Time ;Digital type FX-300 FX-411 ;Analog control-type The functions and performance of a digital Ţ ber sensor at an easily-affordable price! SUNX digital-type sensors have never been more accessible than this. And they are FX-100 target ideal as replacement products for analog control types and teaching types also. ;Teaching type Performance (sensing range), operability 4 Incident light intensity (Price) FX-100 �ORDER GUIDE AmpliŢ ers Accessory Emitting Type Appearance Model No. Output element • CN-14A-C2 NPN open-collector ( ) 6.562 ft FX-101 (Note 2) transistor mOnly include cable set type NPN open-collector FX-101-Z (Note 3) transistor PNP open-collector FX-101P (Note 2) transistor PNP open-collector FX-101P-Z (Note 3) transistor NPN open-collector FX-101-CC2 transistor PNP open-collector FX-101P-CC2 collector transistor Red LED NPN open-collector FX-102 (Note 2) transistor NPN open-collector FX-102-Z (Note 3) transistor PNP open-collector FX-102P (Note 2) transistor PNP open-collector FX-102P-Z (Note 3) transistor NPN open-collector FX-102-CC2 transistor PNP open-collector FX-102P-CC2 transistor Notes: 1) The connector attached cable CN-14A-C2 is supplied with the ampliŢ er. 2) Make sure to use the optional connector attached cable CN-14A-C� or the connector CN-14A. 3) Make sure to use the optional M8 connector attached cable CN-24A-C�. �OPTIONS M8 connector attached cable Designation Model No. Description M8 connector • CN-24A-C� attached cable I CN-24A-C 31.4 "4 1m 3.281 ft 1.236 "0.157 CN-14A-C1 CN-14A-C2 2 2 m 6.562 ft 0.02 mm 4-core cabtyre cable "9 Connector (Note) with connector on one end "0.354 Fixing ring attached cable 3 m 9.843 ft Cable outer diameter:"3.7 mm "0.146 in CN-14A-C3 Protection cover CN-14A-C5 5 m 16.404 ft • FC-FX-1 For M8 plug-in connector type CN-24A-C2 2m 6.562 ft M8 connector The connector on one end attached cable CN-24A-C5 5 m 16.404 ft Cable outer diameter:"4 mm"0.157 in Connector CN-14A Set of 10 housings and 40 contacts AmpliŢ er mounting bracket Protection cover This protects the operating surfaces. FC-FX-1 • MS-DIN-4 AmpliŢ er mounting Mounting bracket for ampliŢ er MS-DIN-4 bracket When it moves depending on the way it is installed on a DIN rail, these end plates ensure that all ampliŢ ers are mounted together in Connector attached cable End plates MS-DIN-E a secure and fully connected manner. • CN-14A-C� Two pcs. per set Contact Connector Note: The connector attached cable CN-14A-C2 is supplied with the cable set type FX-10�(P)-CC2. • Housing 5 Long sensing range type Standard type M8 plug-in M8 plug-in M8 plug-in M8 plug-in Cable set (Note 1) Cable set (Note 1) connector type connector type connector type connector type FX-100 �SPECIFICATIONS Standard type Long sensing range type Type Cable set Cable set NPN output FX-101 (-Z) (Note 4) FX-101-CC2 FX-102 (-Z) (Note 4) FX-102-CC2 Item PNP output FX-101P (-Z) (Note 4) FX-101P-CC2 FX-102P (-Z) (Note 4) FX-102P-CC2 Supply voltage 12 to 24 V DC�10 % Ripple P-P 10 % or less Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) Power consumption ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) NPN open-collector transistor PNP open-collector transistor Output • Maximum sink current:100 mA • Maximum source current: 100 mA • Applied voltage: 30 V DC or less (between output and 0 V) Applied voltage: 30 V DC or less (between output and �V) • • Residual voltage: 1.5 V or less (at 100 mA sink current) • Residual voltage: 1.5 V or less (at 100 mA source current) Output operation Selectable either Light-ON or Dark-ON, at SET mode Short-circuit protection Incorporated NPN non-contact input PNP non-contact input • Signal condition • Signal condition External input High: �8 V to �V DC or Open High: �4 V to�V DC Low: 0 to�2 V DC (Sink current 0.5 to 3 mA) (Source current 0.5 mA or less) Low: 0 to�0.6 V DC or Open • Input impedance: 10 kΩ approx. • Input impedance: 10 kΩ approx. Emission frequency 0: 250 !s or less Emission frequency 1: 2.5 ms or less Emission frequency 1: 450 !s or less Emission frequency 2: 2.8 ms or less Response time Emission frequency 2: 500 !s or less Emission frequency 3: 3.2 ms or less Emission frequency 3: 600 !s or less Emission frequency 4: 5.0 ms or less Sensitivity setting 2-level teaching / Limit teaching / Full-auto teaching Operation indicator Orange LED (lights up when the output is ON) 4 digits (green)�4 digits (red) LCD display Digital display Fine sensitivity adjustment function Incorporated ON-delay / OFF-delay timer, switchable either effective or ineffective. Timer function [Timer period:1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms] Light emitting amount selection Incorporated / Switchable either effective or ineffective function Incorporated Incorporated Interference prevention Emission frequency selection method (Note 2) Emission frequency selection method (Note 2) function (Functions at emission frequency 1, 2 or 3) (Functions at emission frequency 1, 2 , 3 or 4) �10 to �55 �C �14 to �131 �F (If 4 to 7 units are mounted close together: �10 to �50 �C �14 to �122 �F, if 8 to 16 units are : Ambient temperature �10 to �45 �C �14 to �113 �F) (No dew condensation or icing allowed), Storage: �20 to �70 �C �4 to �158 �F Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH Ambient illuminance Incandescent light: 3,000 ?x at the light-receiving face Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 3) Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 3) Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each 2 Shock resistance 98 m/s acceleration (10 G approx.) in X, Y and Z directions for Ţ ve times each Emitting element (modulated) Red LED (Peak emission wavelength : 632 nm) Material Enclosure: Polycarbonate, Key switch: Polycarbonate, Fiber lock lever: PBT Connecting method Connector (Note 4) 2 Cable extension Total length up to 100 m 328.084 ft is possible with 0.3 mm , or more, cable. Net weight: 15 g approx. Net weight: 15 g approx. Net weight: 15 g approx. Net weight: 15 g approx. Weight Gross weight: 35 g approx. Gross weight: 75 g approx. Gross weight: 35 g approx. Gross weight: 75 g approx. CN-14A-C2 CN-14A-C2 Accessory (Connector attached cable, 2 m 6.562 ft long):1pc. (Connector attached cable, 2 m 6.562 ft long):1pc. Notes: 1) Where measurement conditions have not been speciŢ ed precisely, the conditions used were ambient temperature �23 �C �73.4 �F. 2) When using the interference prevention function, set the emission frequencies for the ampliŢ ers to be covered by the interference prevention function to different frequency values. However, the interference prevention function does not operate at emission frequency 0 (factory default setting) for the FX-101(P)(-Z) / FX-101(P)-CC2. 3) The voltage withstandability and the insulation resistance values given in the above table are for the ampliŢ er only. 4) Connector attached cable CN-14A-C2 is not attached to the models that have no ‘-CC2’ at the end of the model Nos. Make sure to use the optional connector attached cable CN-14A-C� or the connector CN-14A. Model Nos. having the sufŢ x ‘-Z’ are M8 plug-in connector type. Make sure to use the optional M8 plug-in connector cable CN-24A-C�. 6 Environmental resistance Model No. FX-100 �I/O CIRCUIT AND WIRING DIAGRAMS NPN output type FX-10�( (-Z/-CC2) ) I/O circuit diagram Terminal arrangement diagram Terminal No. Connector type Color code of cable with connector (Brown) V 1 D Terminal No. Function Load 1 (Black) Output 2 1 �V Tr 2 100 mA max. 12 to 24 V DC 8V ZD 2 Output 10 % 3 (White) Extemal input 3 3 External input 4 m1 0 V (Blue) 0 V 4 4 Internal circuit Users’ circuit Symbols ... D : Reverse supply polarity protection diode ZD: Surge absorption zener diode M8 plug-in connector type Tr : NPN output transistor m1 Terminal No. Function Non-voltage contact or NPN open-collector transistor 1 2 2 1 �V or 2 Output 4 3 External input 3 3 High (�8 V to �V DC or open): Ineffective 4 0 V Low [(0 to �2 V DC (source current 0.5 mA or less)] : Effective PNP output type FX-10�P( (-Z/-CC2) ) I/O circuit diagram Terminal arrangement diagram Terminal No. Connector type Color code of cable with connector (Brown) V 1 m1 Terminal No. Function 1 (White) External input 3 1 �V 2 12 to 24 V DC ZD 100 mA max. Output 2 10 % 3 Tr 2 3 External input (Black) Output 4 Load D (Blue) 0 V 4 0 V 4 Internal circuit Users’ circuit ... Symbols D : Reverse supply polarity protection diode ZD: Surge absorption zener diode M8 plug-in connector type Tr : PNP output transistor m1 Terminal No. Function Non-voltage contact or PNP open-collector transistor 1 2 2 1 �V or 2 Output 4 3 External input 3 3 High [�4 V to �V DC (sink current 0.5 to 3 mA)]: Effective 4 0 V Low (0 to �0.6 V DC or open): Ineffective 7 Sensor circuit Sensor circuit FX-100 �LIST OF FIBERS Pliable Ţ bers (ţ exible and sharp bending Ţ bers) are marked with light blue in the table. Thru-beam type (one pair set) Fiber cable Sensing range (mm in)(Note) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut Lens mountable M4 400 15.748 FT-B8 1,150 45.276 R25 mm Lens mountable R0.984 in M4 FT-FM2 Sleeve 90 mm 3.543 in M4 Fiber 800 31.496 R25 mm FT-FM2S 300 11.811 "1.48"0.058 R0.984 in 2m Sleeve Sleeve 40 mm 1.575 in M4 6.562 ft R10 mm FT-FM2S4 R0.394 in "1.48"0.058 Lens mountable M4 R1 mm 650 25.591 260 10.236 FT-W8 R0.039 in Lens mountable M4 R4 mm 230 9.055 650 25.591 R0.157 in FT-P80 Flexible Lens mountable M4 1 m R10 mm 260 10.236 800 31.496 FT-P81X 3.281 ft R0.394 in Tough flexible M4 Lens mountable R4 mm 2 m 130 5.118 300 11.811 R0.157 in FT-P60 6.562 ft Flexible M4 215 8.465 570 22.441 W7H9D13.9 FT-WR80 W0.276H0.354D0.547 R1 mm 2m With lens M4 R0.039 in 6.562 ft 430 16.929 1,150 45.276 W7H9D14.6 FT-WR80L W0.276H0.354D0.575 Lens mountable M4 R25 mm 180 7.087 430 16.929 2m FT-R80 R0.984 in 6.562 ft Lens mountable (except FX-LE2) M3 800 31.496 FT-T80 300 11.811 R25 mm R0.984 in M3 FT-NFM2 Sleeve 90 mm 3.543 in Fiber M3 130 5.118 280 11.024 R25 mm FT-NFM2S "0.88"0.035 R0.984 in 2m Sleeve Sleeve 40 mm 1.575 in M3 6.562 ft R10 mm FT-NFM2S4 R0.394 in "0.88"0.035 M3 R1 mm 220 8.661 80 3.150 FT-W4 R0.039 in R4 mm M3 80 3.150 240 9.449 R0.157 in FT-P40 Flexible With lens M14 R25 mm 15,000 590.550 10 m FT-FM10L 9,300 366.141 R0.984 in 32.808 ft Note: Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. 8 Threaded type Long sensing M3 M4 Elbow Nut type range g FX-100 �LIST OF FIBERS Pliable Ţ bers (ţ exible and sharp bending Ţ bers) are marked with light blue in the table. Thru-beam type (one pair set) Fiber cable Sensing range (mm in)(Note) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut With lens • Long sensing range "3 "0.118 600 23.622 FT-WS8L 1,500 59.055 R1 mm 2m R0.039 in 6.562 ft "3 "0.118 150 5.906 600 23.622 FT-WS3 With lens • Long sensing range "2.5 "0.098 2,400 94.488 FT-SFM2L 760 29.921 R25 mm R0.984 in "2.5 "0.098 800 31.496 2m FT-SFM2 300 11.811 6.562 ft "2.5 "0.098 R1 mm 650 25.591 260 10.236 FT-WS8 R0.039 in "1.5 "0.059 R25 mm 130 5.118 FT-SNFM2 280 11.024 R0.984 in 2m 6.562 ft "1.5 "0.059 R1 mm 220 8.661 80 3.150 FT-WS4 R0.039 in "1.5 "0.059 1m 330 12.992 120 4.724 FT-P2 3.281 ft R4 mm R0.157 in "1"0.039 Flexible 500 mm 40 1.575 90 3.543 FT-PS1 19.685 in Beam diameter "0.25 "3 "0.125 mm "0.005 in 500 mm "0.010""0.118 19 0.748 6 0.236 FT-E12 19.685 in Sleeve part cannot be bent. R5 mm Beam diameter "0.4 "3 R0.197 in "0.25 mm "0.010 in "0.016""0.118 1m 15 0.591 60 2.362 FT-E22 3.281 ft Sleeve part cannot be bent. "4 "0.157 1,000 39.370 2,350 92.520 FT-V10 3 0.118 2m "1.5 ""0.059 6.562 ft "2.5 "0.098 180 7.087 470 18.504 FT-SFM2SV2 0.8 8 0.031 0 Sleeve p part cannot be bent. R25 mm "1 "0.039 R0.984 in 1 m "2"0.079 0.6 6 0.024 0 140 5.512 FT-V22 380 14.961 3.281 ft Sleeve part cannot be bent. "1"0.039 "2.5"0.098 120 4.724 0.6 6 0.024 0 40 1.575 FT-V41 Sleeve part cannot be bent. 2 m "1"0.039 6.562 ft R1 mm "2 "0.079 1 0.039 0 30 1.181 FT-WV42 80 3.150 R0.039 in Sleeve part cannot be bent. Note: Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. 9 Cylindrical type "1 Side-view Ultra-small diameter "1.5 "0.059 "2.5 "0.098 "3"0.118 "0.039 FX-100 �LIST OF FIBERS Pliable Ţ bers (ţ exible and sharp bending Ţ bers) are marked with light blue in the table. Thru-beam type (one pair set) Fiber cable Sensing range (mm in)(Note 1) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut Easy mounting • Top sensing R1 mm W3H8D12 1,200 47.244 2,800 110.236 FT-WZ8H R0.039 in W0.118H0.315D0.472 R4 mm 1,400 55.118 3,100 122.047 R0.157 in FT-Z8H Flexible Easy mounting • Side sensing R1 mm W3H12D8 700 27.559 2,100 82.677 FT-WZ8E R0.039 in W0.118H0.472D0.315 2m R4 mm 6.562 ft 800 31.496 1,850 72.835 R0.157 in FT-Z8E Flexible Easy mounting • Front sensing R1 mm 950 37.402 W8.5H12D3 330 12.992 FT-WZ8 R0.039 in W0.335H0.472D0.118 R4 mm 360 14.173 1,000 39.370 R0.157 in FT-Z8 Flexible Front sensing 670 26.378 230 9.055 W10H7D2 FT-WZ4 W0.394H0.276D0.079 1 m Fiber bending type 3.281 ft W2H10D10 W0.079H0.394D0.394 80 3.150 230 9.055 FT-WZ4HB R1 mm Front sensing R0.039 in 330 12.992 1,000 39.370 W14H7D3.5 FT-WZ7 W0.551H0.276D0.138 2m Fiber bending type 6.562 ft W3.5H14D11 W0.138H0.551D0.433 580 22.835 190 7.480 FT-WZ7HB """3.5 "0.138 R25 mm 3,000 118.110 1,000 39.370 FT-K8 """3.7 R0.984 in "0.146 Side-view type with small light dispersion R1 mm 700 27.559 2,200 86.614 FT-WKV8 "4"0.157 R0.039 in 2 m 3 6.562 ft R25 mm 0.118 1,000 39.370 3,000 118.110 FT-KV8 R0.984 in W2H1.5D20 W0.079H0.059D0.787 R10 mm 2 0.079 135 5.315 500 19.685 FT-KV1 R0.394 in Wide area sensing R1 mm FT-WA30 Sensing width R0.039 in 32 mm 1.260 in (Note 2) (No ote te 2) (Note 2) (No ote te 2) 3,500 137.795 3,500 137.795 W5H69D20 W0.197H2.717D0.787 R10 mm FT-A30 R0.394 in 2m Wide area sensing 6.562 ft R1 mm FT-WA8 Sensing g width R0.039 in 11 mm 0.433in (Note 2) (No ote te 2) 3,500 137.795 1,500 59.055 W4.2H31D13.5 R10 mm FT-A8 W0.165H1.220D0.531 R0.394 in Top sensing W5H15D15 W0.197H0.591D0.591 280 11.024 720 28.346 FT-AFM2 R25 mm 2m Side sensing R0.984 in 6.562 ft 240 9.449 670 26.378 FT-AFM2E W5H15D15 W0.197H0.591D0.591 Notes: 1) Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. 2) The Ţ ber cable length practically limits the sensing range to 3,500 mm 137.795 in long. 10 Special Rectangular Array Wide beam Narrow beam Compact FX-100 �LIST OF FIBERS Thru-beam type (one pair set) Fiber cable Sensing range (mm in)(Note 1) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut 350C 662F Lens mountable R25 mm M4 FT-H35-M2 R0.984 in 2 m 170 6.693 490 19.291 Fiber 6.562 ft 350C 662F R25 mm Sleeve 60 mm 2.362 in M4 R0.984 in Sleeve FT-H35-M2S6 R10 mm "2.1"""0.083 R0.394 in Allows flexible wiring 200C 392F 1m R10 mm Lens mountable 100 3.937 300 11.811 FT-H20W-M1 M4 3.281 ft R0.394 in 200C 392F Lens mountable 1 m M4 210 8.268 540 21.260 FT-H20-M1 3.281 ft R25 mm 130C 266F R0.984 in Lens mountable (FX-LE2 only) 2 m 250 9.843 700 27.559 FT-H13-FM2 M4 6.562 ft Lens mountable (FX-LE1) FT-H20-J20-S 200 mm 7.874 in (Note 4) (Note 2) M4 420 16.535 300 mm 11.811 in FT-H20-J30-S 135 5.315 (Note 2) Heat- (Note 4) resistant side Ţ ber 500 mm 19.685 in FT-H20-J50-S R18 mm (Note 2) (Note 4) R0.709 in Side-view (Note 3) FT-H20-VJ50-S 500 mm 19.685 in (Note 2) (Note 4) """3.8 150 5.906 500 19.685 "0.150 """4 800 mm 31.496 in FT-H20-VJ80-S "0.157 (Note 2) (Note 4) Easy mounting • Rectangular head SEMI S2 compliant W7H15D13 W0.276H0.591D0.512 R25 mm 520 20.472 3,100 122.047 2m FT-Z802Y R0.984 in 6.562 ft "5.5 "0.217 2,600 102.362 1,100 43.307 FT-L80Y 2m R30 mm "5.5"0.217 6.562 ft R1.181 in Side-view (Note 5) 340 13.386 800 31.496 FT-V80Y 300C 572F Lens mountable (FV-LE1/SV2 only) 1m R18 mm FT-H30-M1V-S 110 4.331 280 11.024 M4 3.281 ft R0.709 in (Note 6) Notes: 1) Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. 2) This is the Ţ ber length (Ţ xed length) for heat-resistant side Ţ bers. The ordinary-temperature side Ţ bers are free-cut to 2 m 6.562 ft. 3) The ordinary-temperature side Ţ ber is R25 mm R0.984 in or more. 4) Heat-resistant joint Ţ bers and ordinary-temperature side Ţ bers (FT-FM2) are sold as a set. Please refer to ‘Heat-resistant joint Ţ ber catalog’ for details. 5) The allowable cutting range is 500 mm 19.685 in from the end that the ampliŢ er inserted. 6) Sold as a set comprising vacuum-resistant type Ţ ber�photo-terminal (FV-BR1)�Ţ ber at atmospheric side (FT-J8). Please refer to ‘Vacuum-resistant Ţ ber catalog’ for details. Model No. when ordering heat-resistant joint Ţ bers individually as replacement parts • FT-H20-J20 (one pair set) • FT-H20-J30 (one pair set) • FT-H20-J50 (one pair set) • FT-H20-VJ50 (one pair set) • FT-H20-VJ80 (one pair set) Model No. when ordering vacuum-resistant Ţ bers individually as replacement parts • Vacuum-resistant type fiber • Photo-terminal • Fiber at atmospheric side FT-H30-M1V (one pair set) FV-BR1 (one pair set) FT-J8 (one pair set) 11 Special Vacuum- Chemical-resistant Heat-resistant • Joint Heat-resistant resistant FX-100 �LIST OF FIBERS Pliable Ţ bers (ţ exible and sharp bending Ţ bers) are marked with light blue in the table. Retroreţ ective type Fiber cable Sensing range (mm in)(Note 1, 2) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut W9.5H5.2D15 W0.374H0.205D0.591 100 to 550 100 to 830 R1 mm 2m FR-WKZ11 3.937 to 21.654 3.937 to 32.677 R0.039 in 6.562 ft W30H30D0.5 W1.181H1.181D0.020 W9.5H5.2D21 W0.374H0.205D0.827 FR-KZ21 W10.6H28D10.1 W0.417H1.102D0.398 R10 mm 200 7.874 200 7.874 2 m W9.5H25 R0.394 in 6.562 ft D5.2 FR-KZ21E W0.374H0.984 W10.6H28D10.1 D0.205 W0.417H1.102D0.398 W7.5H2.2D11.2 W0.295H0.087D0.441 15 to 200 15 to 360 R10 mm 2m FR-KV1 0.591 to 7.874 0.591 to 14.173 R0.394 in 6.562 ft W4H2D21.5 W0.157H0.079D0.846 Notes: 1) Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. The sensing range of FR-WKZ11 is speciŢ ed for the RF-13. The sensing range of FR-KZ21, FR-KZ21E and FR-KV1 is speciŢ ed for the attached reţ ector. The sensing ranges when using in combination with the FR-WKZ11 reţ ector (optional) are given in the below table. AmpliŢ er FX-101� FX-102� Reţ ector FR-WKZ11�RF-210 100 to 700 3.937 to 27.559 100 to 1,100 3.937 to 43.307 FR-WKZ11�RF-220 100 to 1,300 3.937 to 51.181 100 to 2,600 3.937 to 102.362 FR-WKZ11�RF-230 100 to 2,000 3.937 to 78.740 100 to 4,000 3.937 to 157.480 2) The sensing range of FR-WKZ11 is the possible setting range for the reţ ector or reţ ective tape. The Ţ ber can detect an object less than 100 mm 3.937 in away. However, note that if there are any white or highly-reţ ective surfaces near the Ţ ber head, reţ ected incident light may affect the Ţ ber head. If this occurs, adjust the threshold value of the ampliŢ er unit before use. The sensing range of FR-KZ21(E) is the possible setting range for the reţ ector. However, if setting the Ţ ber to detect objects passing within 0 to 20 mm 0 to 0.787 in from the Ţ ber head, unstable detection may result. The sensing range of FR-KV1 is the possible setting range for the reţ ector. The Ţ ber can detect an object less than 15 mm 0.591 in away. Reţ ective type Fiber cable Sensing range (mm in)(Note 1, 2) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut M6 170 6.693 440 17.323 FD-B8 R25 mm R0.984 in Coaxial M6 100 3.937 410 16.142 FD-FM2 Sleeve 90 mm 3.543 in Fiber M6 R25 mm FD-FM2S R0.984 in """""2.5"0.098 100 3.937 345 13.583 2 m Sleeve Sleeve 40 mm 1.575 in 6.562 ft M6 R10 mm FD-FM2S4 R0.394 in """"""2.5"0.098 M6 R1 mm 80 3.150 230 9.055 FD-W8 R0.039 in R4 mm 200 7.874 90 3.543 R0.157 in FD-P80 Flexible M6 M6 1m R10 mm 70 2.756 220 8.661 FD-P81X 3.281 ft R0.394 in Tough flexible M6 R25 mm 70 2.756 180 7.087 2m FD-R80 R0.984 in 6.562 ft Notes: 1) The sensing range is speciŢ ed for white non-glossy paper (400�400 mm 15.748�15.748 in) as the object. 2) Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. 12 Threaded type Narrow beam Sharp bending Wafer mapping With polarizing p M6 Side sensing Top sensing Elbow Ţ lters FX-100 �LIST OF FIBERS Pliable Ţ bers (ţ exible and sharp bending Ţ bers) are marked with light blue in the table. Reţ ective type Fiber cable Sensing range (mm in)(Note 1, 2) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut M4 110 4.331 345 13.583 FD-T80 R25 mm R0.984 in M4 FD-NFM2 Sleeve 90 mm 3.543 in Fiber M4 35 1.378 100 3.937 FD-NFM2S R25 mm "1.48"0.058 R0.984 in Sleeve 40 mm 1.575 in Sleeve M4 R10 mm FD-NFM2S4 "1.48"0.058 R0.394 in Sleeve 40 mm 1.575 in Fiber R1 mm R0.039 in M4 15 0.591 40 1.575 2 m FD-W44 Sleeve 6.562 ft "1.48"0.058 R10 mm R0.394 in M4 R1 mm 80 3.150 230 9.055 FD-WT8 R0.039 in Small spot for sensing minute objects R2 mm Coaxial • Lens mountable 75 2.953 28 1.102 FD-WG4 R0.079 in R25 mm M4 120 4.724 50 1.969 FD-G4 R0.984 in R4 mm 150 5.906 45 1.772 R0.157 in FD-P60 M4 Flexible Small diameter R25 mm 35 1.378 100 3.937 FD-T40 R0.984 in M3 M3 R1 mm 40 1.575 15 0.591 FD-WT4 R0.039 in 2 m R4 mm 6.562 ft M3 30 1.181 8 0.315 R0.157 in FD-P40 Flexible Lens mountable (FX-MR3, FX-MR6) M3 R25 mm 50 1.969 120 4.724 FD-G6 R0.984 in Coaxial Lens mountable (FX-MR3, FX-MR6) M3 R10 mm 160 6.299 1 m 45 1.772 FD-G6X 3.281 ft R0.394 in Coaxial Tough flexible (Note 3) Coaxial • Lens mountable (FX-MR3, FX-MR6) R25 mm M3 18 0.709 50 1.969 FD-EG1 R0.984 in High precision Coaxial • Lens mountable (FX-MR3, FX-MR6) M3 Light emitting 10 0.394 30 1.181 FD-EG2 fiber element "0.175 "0.007 High precision 500 mm R10 mm Coaxial • Lens mountable (FX-MR3, FX-MR6) 19.685 in R0.394 in M3 Light emitting 22 0.866 7 0.276 FD-EG3 fiber element "0.125 "0.005 High precision M3 "0.5"0.020 1 0.039 4 0.157 FD-EN500S1 Sleeve part cannot be bent. R25 mm Coaxial R0.984 in M3 "0.8"0.031 1m 15 0.591 48 1.890 FD-ENM1S1 3.281 ft Sleeve part cannot be bent. Notes: 1) The sensing range is speciŢ ed for white non-glossy paper [200�200 mm 7.874�7.874 in (FD-T80, FD-WT8: 400�400 mm 15.748�15.748 in, FD-W44, FD-WT4, FD-P40, FD-G6, FD-EG1, FD-EG2, FD-EG3, FD-EN500S1, FD-ENM1S1: 100�100 mm 3.937�3.937 in)] as the object. 2) Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. 3) The allowable cutting range is 700 mm 27.559 in from the end that the ampliŢ er inserted. 13 Threaded type M3 M4 FX-100 �LIST OF FIBERS Pliable Ţ bers (ţ exible and sharp bending Ţ bers) are marked with light blue in the table. Reţ ective type Fiber cable Sensing range (mm in)(Note 1, 2) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut "3"0.118 R25 mm 100 3.937 345 13.583 FD-S80 R0.984 in "3"0.118 R1 mm 80 3.150 230 9.055 FD-WS8 R0.039 in 2 m Coaxial 6.562 ft R2 mm 75 2.953 28 1.102 FD-WSG4 R0.079 in "3"0.118 R4 mm "3"0.118 150 5.906 45 1.772 R0.157 in FD-P50 Flexible "2.5 R25 mm "0.098 35 1.378 100 3.937 2 m FD-SNFM2 R0.984 in 6.562 ft "1.5"0.059 R4 mm 1 m 25 0.984 65 2.559 R0.157 in FD-P2 3.281 ft Flexible "1.5 """0.5 "0.059"0.020 R10 mm 13 0.512 3.5 0.138 FD-E12 R0.394 in Sleeve part cannot be bent. 1m Coaxial 3.281 ft "3"0.118 R25 mm 16 0.630 45 1.772 FD-E22 "0.65"0.026 R0.984 in Sleeve part cannot be bent. Small diameter """""1.5""""0.059 R25 mm 70 2.756 25 0.984 FD-V41 0.7 7 0.028 0 "3"0.118 R0.984 in Sleeve part cannot be bent. """3 """2 """""0.118 ""0.079 R1 mm 20 0.787 6 0.236 2 m FD-WV42 1 0.039 0 R0.039 in 6.562 ft Sleeve part cannot be bent. b """5 """2 """"0.197""0.079 R25 mm 30 1.181 90 3.543 FD-SFM2SV2 0.8 8 0.031 0 R0.984 in Sleeve part cannot be bent. b Glass substrate detection • Mapping R25 mm 16 to 30 0.630 to 1.181 12 to 50 0.472 to 1.969 4 m FD-L46 R0.984 in 13.123 ft W25H7.3D30 W0.984H0.287D1.181 Glass substrate detection • Alignment W20H29D3.8 0 to 40 0to1.575 0 to 50 0 to 1.969 3 m FD-L45 W0.787H1.142D0.150 9.843 ft R4 mm Glass substrate detection • Alignment R0.157 in 0 to 19 0 to 0.748 0 to 25 0 to 0.984 W17H29D3.8 2 m FD-L43 W0669H1.142D0.150 6.562 ft Glass substrate detection • Seating confirmation 0 to 8 0 to 0.315 0 to 6 0 to 0.236 FD-L44 R10 mm 2m R0.394 in 6.562 ft 0 to 4.5 0 to 0.177 0 to 5.5 0 to 0.217 W12H19D3 FD-L44S W0.472H0.748D0.118 Glass substrate detection 7 to 12 0.276 to 0.472 6 to 13.5 0.236 to 0.531 R1 mm FD-WL41 (Convergent point 8 0.315) (Convergent point 8 0.315) R0.039 in 3 to 14 0.118 to 0.551 1.5 to 16 0.059 to 0.630 2m FD-L41 W24H21D4 (Convergent point 8 0.315) (Convergent point 8 0.315) 6.562 ft W0.945H0.827D0.157 R10 mm R0.394 in 5 to 8 0.197 to 0.315 1 to 17 0.039 to 0.669 W6H18D14 FD-L4 W0.236H0.709D0.551 (Convergent point 6 0.236) (Convergent point 6 0.236) 1 m R1 mm 1 to 4.5 0.039 to 0.177 0.5 to 6.5 0.020 to 0.256 FD-WL48 W7.2H7.5D2 3.281 ft R0.039 in W0.283H0.295D0.079 Notes: 1) The sensing range is specified for white non-glossy paper (FD-S80, FD-WS8: 400�400 mm 15.748�15.748 in, FD-WSG4, FD-P50, FD-SNFM2, FD-V41, FD-SFM2SV2: 200�200 mm 7.874�7.874 in, FD-P2, FD-E12, FD-E22, FD-WV42, FD-L4, FD-WL48: 100�100 mm 3.937�3.937 in, FD-L46: 100�100�t 0.7 mm 3.937�3.937�t 0.028 in R edge of LCD glass substrates, FD-L43, FD-L44 4 and FD-L45: 100�100�t 0.7 mm 3.937�3.937� t 0.028 in LCD glass substrates, FD-L44S: silicon wafers polished surface, FD-WL41, FD-L41: 100�100�t 2 mm 3.937�3.937�t 0.079 in glass substrates) 2) Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. 14 Rectangular Cylindrical type "1.5 "2.5 Convergent reţ ective type Side-view Ultra-small diameter "3 "0.118 "0.059 "0.098 FX-100 �LIST OF FIBERS Pliable Ţ bers (ţ exible and sharp bending Ţ bers) are marked with light blue in the table. Reţ ective type Fiber cable Sensing range (mm in)(Note 1, 2) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut Front sensing W10H7D2 FD-WZ4 W0.394H0.276D0.079 2 to 20 0.079 to 0.787 1 to 70 0.039 to 2.756 1m Fiber bending type 3.281 ft W2H D10 FD-WZ4HB W0.079H0.394D0.394 R1 mm Front sensing R0.039 in 1 to 55 0.039 to 2.165 160 6.299 W14H7D3.5 FD-WZ7 W0.551H0.276D0.138 2m Fiber bending type 6.562 ft 0.5 to 180 0.020 to 7.087 1 to 60 0.039 to 2.362 W3.5H14D11 FD-WZ7HB W0.138H0.551D0.433 Long sensing range • Rectangular head 20 to 480 R1 mm 20 to 180 0.787 to 7.087 2 m FD-WKZ1 W5.2 5D15 0.787 to 18.898 R0.039 in 6.562 ft W0.205H0.374D0.591 R25 mm 125 4.921 250 9.843 2m FD-A15 R0.984 in 6.562 ft W7H15D30 W0.276H0.591D1.181 Top sensing 285 11.220 105 4.134 FD-AFM2 W5 H20D20 W0.197H0.787D0.787 R25 mm 2 m Side sensing R0.984 in 6.562 ft 85 3.346 245 9.646 FD-AFM2E W5 H20D20 W0.197H0.787D0.787 Protective tube Contact type R40 mm "6 "0.236 2 m R1.575 in FD-F8Y Fiber 6.562 ft R15 mm (Note 3) R0.591 in Mountable on pipe • Applicable pipe diameter: Standard Outer dia."6 to "26 mm"0.236 to "1.024 in transparent pipe FD-F41 W25H13D20 [PVC (vinyl chloride), ţ uorine resin, polycarbonate, acrylic, glass, wall thickness 1 to 3 mm 0.039 to 0.118 in] W0.984H0.512D0.787 R10 mm 2 m Mountable on pipe • For PFA, wall R0.394 in Applicable pipe diameter: 6.562 ft thickness 1 mm 0.039 in pipe Outer dia."6 to "26 mm"0.236 to "1.024 in transparent pipe FD-F4 W25H13D20 [PFA (ţ uorine resin) or equivalently transparent pipe, wall thickness 1 mm 0.039 in] W0.984H0.512D0.787 Notes: 1) The sensing range is speciŢ ed for white non-glossy paper [200�200 mm 7.874�7.874 in (FD-WKZ1, FD-AFM2, FD-AFM2E: 400�400 mm 15.478�15.478 in)] as the object. 2) Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. 3) The allowable cutting range is 1,000 mm 39.370 in from the end that the ampliŢ er inserted. 15 Special Rectangular Long sensing Liquid level sensing Array Wide beam Compact range g g FX-100 �LIST OF FIBERS Reţ ective type Fiber cable Sensing range (mm in)(Note 1, 2) Shape of Ţ ber head Bending Type length Model No. (mm in) radius Standard type FX-101� Long sensing range type FX-102� : Free-cut 350C 662F • Coaxial R25 mm M6 FD-H35-M2 R0.984 in 2m 75 2.953 280 11.024 Fiber 350C 662F • Sleeve 60 mm 2.362 in 6.562 ft R25 mm R0.984 in """2.8 Sleeve FD-H35-M2S6 M6 ""0.110 R10 mm R0.394 in 200C 392F • Coaxial R25 mm M6 120 4.724 300 11.811 FD-H20-M1 R0.984 in Fiber 350C 662F • Sleeve 90 mm 3.543 in R25 mm R0.984 in 1m Sleeve 200 7.874 85 3.346 FD-H35-20S 3.281 ft """2.1 R10 mm M4 "0.083 R0.394 in 200C 392F • Coaxial 90 3.543 280 11.024 FD-H20-21 M4 300C 572F • Glass substrate detection Convergent reflective type 2 m W19H27D5 0 to 17 0 to 0.669 2 to 9 0.079 to 0.354 FD-H30-L32 6.562 ft W0.748H1.063 D0.197 R25 mm 180C 356F • Glass substrate detection R0.984 in Convergent reflective type y y y W19H27D5 0 to 10 0 to 0.394 0 to 25 0 to 0.984 FD-H18-L31 W0.748H1.063 D0.197 2 m 130C 266F 6.562 ft M6 100 3.937 280 11.024 FD-H13-FM2 300C 572F • Rectangular head W9.5H5.2D15 W0.374H0.205D0.591 FD-H30-KZ1V-S 1m 25 to 80 0.984 to 3.150 10 to 220 0.394 to 8.661 3.281 ft (Note 3) R18 mm 300C 572F • Glass substrate detection R0.709 in Convergent reflective type 3 m FD-H30-L32V-S W19H5D27 0 to 11 0 to 0.433 2.5 to 6.5 0.098 to 0.256 W0.748H0.197 9.843 ft (Note 3) D1.063 Notes: 1) The sensing range is speciŢ ed for white non-glossy paper [400�400 mm 15.748�15.748 in (FD-H30-L32, FD-H18-L31: 50�50 mm 1.969�1.969 in glass substrate, FD-H30-KZ1V-S, FD-H30-L32V-S: 100�100�t 0.7 mm 3.937�3.937�t 0.028 in transparent glass)] as the object. 2) Please take care that the sensing range of the free-cut type Ţ ber may be reduced by 20 % max. depending upon how the Ţ ber is cut. 3) Sold as a set comprising vacuum-resistant type Ţ ber�photo-terminal (FV-BR1)�Ţ ber at atmospheric side (FT-J8). Model No. when ordering vacuum-resistant Ţ bers individually as replacement parts • Vacuum-resistant type fiber • Mounting bracket for FD-H30-KZ1V • Photo-terminal • Fiber at atmospheric side FD-H30-KZ1V MS-FD-2 FV-BR1 (one pair set) FT-J8 (one pair set) FD-H30-L32V Accessories (attached with Ţ bers) RF-003 (FR-KZ21/KZ21E exclusive reflector) • RF-003 • RF-13 • FX-CT1 • FX-CT2 RF-13 (Reflective tape) FX-CT1 (Fiber cutter) FX-CT2 (Fiber cutter) FX-AT2 (Attachment for fixed-length fiber, Orange) FX-AT3 (Attachment for "2.2 mm"0.087 in fiber, Clear orange) FX-AT4 (Attachment for "1 mm "0.039 in fiber, Black) FX-AT5 (Attachment for "1.3 mm"0.051 in fiber, Gray) FX-AT6 (Attachment for "1 mm "0.039 in / "1.3 mm"0.051 in mixed fiber, Black / Gray) • FX-AT2 • FX-AT3 • FX-AT4 If connecting to a Ţ ber ampliŢ er other than the FX-100 series Applicable fiber amplifiers: FX2 // FX3 series FX-AT10 (Attachment for "1 mm"0.039 in fiber) FX-AT13 (Attachment for "1.3 mm "0.051 in fiber) FX-AT15 (Attachment for "1 mm "0.039 in / "1.3 mm"0.051 in mixed fiber) • FX-AT10 • FX-AT5 • FX-AT6 • FX-AT13 • FX-AT15 16 Special Vacuum-resistant Heat-resistant FX-100 �FIBER OPTIONS Lens (For thru-beam type Ţ ber) Designation Model No. Description Increases the sensing Sensin Sensing range (mm) [Lens on both sides] g range (mm) [Lens on both sides] range by 5 times or more. AmpliŢ er FX-101� FX-102� Fiber • Ambient temperature: FT-B8 2,200 2,200 3 3,500 ,500 ( (Note 2) Note 2) �60 to �350 °C FT-FM2, FT-T80 3,000 3,000 3, 3,500 500 ( (Note 2) Note 2) Expansion FT-R80 1,900 1,900 3 3,500 ,500 ( (Note 2) Note 2) �76 to �662 °F lens FT-W8 3 3,000 ,000 3 3,500 ,500 ( (Note 2) Note 2) FX-LE1 FT-P80, FT-P60 3 3,500 ,500 ( (Note 2) Note 2) 3 3,500 ,500 ( (Note 2) Note 2) (Note 1) FT-P81X 1,600 1,600 ( (Note 2) Note 2) 1,600 1,600 ( (Note 2) Note 2) FT-H35-M2 2,000 2,000 3, 3,500 500 ( (Note 2) Note 2) FT-H20W-M1 1,300 1,300 1,600 1,600 ( (Note 2) Note 2) FT-H20-M1 1,600 1,600 ( (Note 2) Note 2) 1,600 1,600 ( (Note 2) Note 2) FT-H20-J20-S,, FT-H20-J30-S,, FT-H20-J50-S 1 1,000 ,000 3, 3,500 500 ( (Note 2) Note 2) Tremendously increases the Sensin Sensing range (mm) [Lens on both sides] g range (mm) [Lens on both sides] sensing range with large AmpliŢ er FX-101� FX-102� diameter lenses. Fiber Super- FT-B8,,, FT-FM2, FT-R80,, FT-W8,, FT-P80,, FT-P60 3 3,500 ,500 ( (Note 2) Note 2) 3 3,500 ,500 ( (Note 2) Note 2) expansion FT-P81X 1 1,600 ,600 ( (Note 2) Note 2) 1 1,600 ,600 ( (Note 2) Note 2) FX-LE2 • Ambient temperature: lens FT-H35-M2 3 3,500 ,500 ( (Note 2) Note 2) 3 3,500 ,500 ( (Note 2) Note 2) �60 to �350 °C (Note 1) FT-H20W-M1, FT-H20-M1 1,600 1,600 ( (Note 2) Note 2) 1,600 1,600 ( (Note 2) Note 2) �76 to �662 °F FT-H13-FM2 3 3,500 ,500 ( (Note 2) Note 2) 3 3,500 ,500 ( (Note 2) Note 2) FT-H20-J20-S,,, FT-H20-J30-S, FT-H20-J50-S 3 3,500 ,500 ( (Note 2) Note 2) 3 3,500 ,500 ( (Note 2) Note 2) Beam axis is bent by 90 °. Sensing range (mm) [Lens on both sides Sensing range (mm) [Lens on both sides] ] AmpliŢ er FX-101� FX-102� • Ambient temperature: Fiber �60 to �300 °C FT-B8 530 530 1,45 1,450 0 �76 to �572 °F FT-FM2, FT-T80 550 550 1,70 1,700 0 FT-W8 45 450 0 1,300 1,300 Side-view FX-SV1 FT-P80 42 420 0 1,40 1,400 0 lens FT-P60 300 300 850 850 FT-P81X 5 550 50 1,70 1,700 0 FT-H35-M2 2 280 80 800 800 FT-H20W-M1 1 140 40 4 400 00 FT-H20-M1 2 280 80 8 840 40 FT-H20-J20-S,,, FT-H20-J30-S, FT-H20-J50-S 1 150 50 41 410 0 Sensing range increases by Sensin Sensing range (mm) [Lens on both sides] (Note 3) g range (mm) [Lens on both sides] (Note 3) Expansion 4 times or more. AmpliŢ er lens for vacuum- FV-LE1 FX-101� FX-102� • Ambient temperature: Fiber resistant Ţ ber FT-H30-M1V 45 450 0 1,60 1,600 , 0 (Note 1) �40 to �120 °C �40 to�248 °F Beam axis is bent by 90 °. Sensin Sensing range (mm) [Lens on both sides] (Note 3) g range (mm) [Lens on both sides] (Note 3) Side-view AmpliŢ er lens for FX-SV2 FX-101� FX-102� • Ambient temperature: Fiber vacuum- FT-H30-M1V 4 450 50 1,60 1,600 , 0 resistant Ţ ber �60 to �300 °C �140 to�572 °F Notes: 1) Be careful when installing the thru-beam type Ţ ber equipped with the expansion lens, as the beam envelope becomes narrow and alignment is difŢ cult. Especially when installing a Ţ ber with many cores (sharp bending Ţ bers and heat-resistant glass Ţ ber), please be sure to use it only after you have adjusted it sufŢ ciently. 2) The Ţ ber cable length practically limits the sensing range to 3,500 mm 137.795 in long (FT-H20W-M1, FT-P81X X and FT-H20-M1: 1,600 mm 62.992 in). 3) The Ţ ber cable length for the FT-H30-M1V V is 1m 3.281 ft. The sensing ranges in FX-102� (long sensing range type) take into account the length of the FT-J8 atmospheric side Ţ ber. Lens (For reţ ective type Ţ ber) Designation Model No. Description Pinpoint spot of "0.5 mm"0.020 in. Enables detection of minute objects or small marks. Pinpoint spot • Distance to focal point: 6�1 mm 0.236 � 0.039 in • Applicable Ţ bers: FD-WG4, FD-G4 FX-MR1 lens • Ambient temperature:�40 to�70 °C �40 to�158 °F The spot diameter is adjustable from 0.7 mm " Sensing range for FX-101� (Note) S Screw-in crew-in to 2 mm 0.028 in to 0.079 in according to " " " dept depth h Screw-in depth Distance to focal point Spot diameter how much the Ţ ber is screwed in. 7mm 18.5 mm approx. "0.7 mm Zoom lens FX-MR2 Applicable Ţ bers: FD-WG4, FD-G4 • 12 mm 27 mm approx. "1.2 mm Distance t Distance to o • Ambient temperature:�40 to�70 °C �40 to�158 °F ffocal point ocal point 14 mm 43 mm approx "2.0 mm Sp Spot ot Accessory: MS-EX-3 (mounting bracket) • d diameter iameter Extremely Ţ ne spot of 0.3 mm 0.012 in " " Sensing range for FX-101� (Note) approx. achieved. Fiber model No. Distance to focal point Spot diameter Applicable Ţ bers: FD-WG4, FD-G4, • Finest spot FD-EG3 7.5�0.5 mm "0.15 mm approx. FX-MR3 FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6 lens FD-EG2 7.5�0.5 mm "0.2 mm approx. Ambient temperature: • FD-EG1 7.5�0.5 mm "0.3 mm approx. �40 to�70 °C �40 to�158 °F FD-WG4/G4/G6X/G6 7.5�0.5 mm "0.5 mm approx. Distance to focal point Extremely Ţ ne spot of 0.1 mm 0.004 in " " Sensing range for FX-101� (Note) approx. achieved. Fiber model No. Distance to focal point Spot diameter Spot diameter Applicable Ţ bers: FD-WG4, FD-G4, • Finest spot FD-EG3 7.5�0.5 mm "0.1 mm approx. FX-MR6 FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6 lens FD-EG2 7.5�0.5 mm "0.15 mm approx. Ambient temperature: • FD-EG1 7.5�0.5 mm "0.2 mm approx. �20 to�60 °C �4 to�140 °F FD-WG4/G4/G6X/G6 7.5�0.5 mm "0.4 mm approx. Screw-in depth FX-MR2 is converted into a side-view type Sensing range for FX-101� (Note) and can be mounted in a very small space. Zoom lens Screw-in depth Distance to focal point Spot diameter Applicable Ţ bers: FD-WG4, FD-G4 • Side-view FX-MR5 Distance nce 8 mm 13 mm approx. "0.5 mm to foca al Ambient temperature: type • 10 mm 15 mm approx. ( ( ) "0.8 mm point �40 to�70 °C �40 to�158 °F 14 mm 30 mm approx "3.0 mm Spot diameter Note: The sensing ranges are the values when used in combination with FX-101� (standard type). Please contact our ofŢ ce for details on sensing ranges for other types of ampliŢ er. 17 For reţ ective type Ţ ber For thru-beam type Ţ ber FX-100 �FIBER OPTIONS Others Protective tube Designation Model No. Description • FTP-� • FDP-� FTP-500 (0.5 m 1.640 ft) FT-B8 FT-P80 For FT-FM2 FT-P60 FTP-1000 (1 m 3.281 ft) M4 FT-FM2S FT-FM2S4 thread Protective tube Fiber bender FTP-1500 (1.5 m 4.921 ft) FT-H13-FM2 For thru-beam • FB-1 ( ( type Ţ ber ) FTP-N500 (0.5 m 1.640 ft) FT-T80 FT-P40 For FT-NFM2 FD-T40 M3 FTP-N1000 (1 m 3.281 ft) FT-NFM2S FD-P40 The protective tube, made thread FT-NFM2S4 of non-corrosive stainless FTP-N1500 (1.5 m 4.921 ft) steel, protects the inner FDP-500 (0.5 m 1.640 ft) FD-B8 FD-P80 Ţ ber cable from any Fiber cutter For external forces. FD-FM2 FT-H13-FM2 • FX-CT2 FDP-1000 (1 m 3.281 ft) M6 FD-FM2S thread Protective tube FD-FM2S4 FDP-1500 (1.5 m 4.921 ft) For reţ ective ( ( type Ţ ber ) FDP-N500 (0.5 m 1.640 ft) FD-T80 For FD-NFM2 M4 FDP-N1000 (1 m 3.281 ft) FD-NFM2S thread FD-NFM2S4 FDP-N1500 (1.5 m 4.921 ft) • FX-CT1 The Ţ ber bender bends the sleeve part of the Ţ ber head at the Fiber bender FB-1 proper radius. (Note 1) MS-AJ1-F Horizontal mounting type Universal sensor Mounting stand assembly for Ţ ber mounting stand (For M3, M4 or M6 threaded head Ţ ber) (Note 2) Vertical mounting type MS-AJ2-F Universal sensor mounting stand Using the arm which enables adjustment in FX-CT2 The free-cut type Ţ ber can be easily cut. the horizontal direction, sensing can also Fiber cutter Accessory. FX-CT1 is attached with the FT-P80 or the FD-P80. be done from above an assembly line. The FX-CT2 is provided with Ţ bers other than this. FX-CT1 360 ° rotation • MS-AJ1-F Forward / back Attachment for This is the attachment for the Ţ xed length Ţ ber. Orange. FX-AT2 adjustment: 130 mm Ţ xed-length Ţ ber (Accessory) 5.118 in approx. Height Attachment for "2.2 mm This is the attachment for the "2.2 mm"0.087 in Ţ ber. Clear Orange. adjustment: FX-AT3 "0.087 in Ţ ber (Accessory. Does not attach with the FT-P80 or the FD-P80.) 150 mm 5.906 in approx. Attachment for "1 mm This is the attachment for the"1 mm "0.039 in Ţ ber. Black. 360 ° FX-AT4 20 2 2 2 ° "0.039 in Ţ ber (Accessory) rotation Mounting hole 20 ° for M6 screw Angle adjustment:�20 ° Attachment for "1.3 mm This is the attachment for the"1.3 mm"0.051 in Ţ ber. Gray. FX-AT5 "0.051 in Ţ ber (Accessory) 360 ° rotation • MS-AJ2-F Attachment for "1mm This is the attachment for the "1mm"0.039 in / "1.3 mm"0.051 in Forward / back "0.039 in / "1.3 mm FX-AT6 mixed Ţ ber. Black / Gray. (Accessory) adjustment: 130 mm "0.051 in mixed Ţ ber 5.118 in approx. Height adjustment: Notes: 1) Do not bend the sleeve part of any side-view type Ţ ber or ultra-small diameter head type Ţ ber. 150 mm 2) Refer to the ‘Sensor general catalog 2003-2004’ or the SUNX website: http://www.sunx.jp/ for universal sensor mounting stand. 5.906 in approx. 360 ° 20 2 2 2 ° ° Mounting hole rotation for M6 screw 20 ° Fiber attachment Angle adjustment:�20 ° It’s possible to simultaneously cut two fibers to the same length Each fiber (with some exceptions) has a newly developed two-in-one fiber attachment (FX-AT3/AT4/AT5/AT6) which enables two fibers to be cut simultaneously to the same length with the new fiber cutter (FX-CT2). Also, since the fibers can be attached to the amplifier while being fixed in position in the two-in-one fiber attachment, sensitivity changes resulting from variation in the amount of fiber insertion do not occur. • FX-AT2 • FX-AT3 • FX-AT4 • FX-AT5 • FX-AT6 For fixed-length For"2.2 mm For"1 mm For"1.3 mm For"1 mm "0.039 in / fiber "0.087 in fiber "0.039 in fiber "0.051 in fiber "1.3 mm "0.051 in mixed fiber �PRECAUTIONS FOR PROPER USE ON key / OFF key / Part description • Never use this product as a sensing device for personnel protection. Set value UP key Set value DOWN key Operation indicator • In case of using sensing devices for personnel protection, use products MODE key (Orange) which meet regulations and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. Digital display (Red) Digital display (Green) (Incident light intensity) (Threshold value) 18 Applicable Ţ bers �DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the website: http://www.sunx.jp/ AmpliŢ er AmpliŢ er FX-101�, FX-102� FX-101(P)-Z, FX-102(P)-Z 6 0.236 6 0.236 6 6 10.85 47 1.850 0.236 0.236 0.427 29 1.142 47 47 18 1.850 50 0.8 2.7 0.7 20 12.2 29 29 1 1.142 142 0.031 0.106 0.106 0 0.028 0.480 0.787 0.787 7 12.2 0.8 0.480 0.031 0 0.7 0.028 OFF key / Setting value DOWN key 4.1 0.161 ON key / Setting value UP key Operation indicator (Orange) Operation indicator (Orange) OFF key / Setting value DOWN key 4.1 2.7 0.161 Digital display (Green, Red) MODE key 0.106 ON key / Setting value UP key Digital display (Green, Red) MODE key Assembly dimensions with optional protective cover 9 0.354 1.1 1 0.75 0.030 0.043 0.039 7 "6.5 0.276 "0.256 9 66.2 2 0.079 4 30 10 0.354 2.606 0.157 1.181 .18 0.394 2 0.079 10 6 0.236 0.394 7 0.276 0.8 ""3.2 1.1 3.2 0.031 ""0.126 8.1 0.043 30 3 0.126 10 0.319 1.181 0.118 2 2 0.394 3 0.118 5.5 0.079 0 10 50 50 1.969 1.969 8.1 0.217 0.394 0.319 13.5 35 35 1.378 1 378 "3.2 0.531 3.2 ""0.126 4 64.5 64.5 2.539 2.539 0.126 0 0.157 Suitable for 35 mm 1.378 in width DIN rail 2 0.0 079 5.5 0.217 50 1.969 13.5 35 1.378 0.531 64.5 2.539 Suitable for 35 mm 1.378 in width DIN rail MS-DIN-4 Amplifer mounting bracket (Optional) MS-DIN-E End plate (Optional) "7.2 mm "0.283 in "3.2"0.126 7.2 mm 0.283 in 3.2 sppg ot facing, 4 0.157 deep p p 0.126 spot facing, 4 0.157 deep M3 (Iength 18 mm 0.709 in) pan head screws 2.75 0.108 60 3 3 0.118 2.362 M3 Square nut 0.118 15 5.6 1 0.591 0.220 0.039 9.25 15 0.364 0.591 6.2 mm 0.244 in 24.7 spot facing, 3 0.118 deep "6.2 mm "0.244 in 0.972 spot facing, 3 0.118 deep 9 3.2 "3.2"0.126 0.354 0.126 1.6 32 4 11.5 0.063 1.260 0.157 0.453 Suitable for 35mm 1.378 in width DIN rail Material: Polycarbonate 4 1 0.157 0.039 24.5 5 0.965 0.197 35 1.378 Material: PBT Connector attached cable (Optional) CN-14A-C� CN-14A-C2 is attached FX-101(P)-CC2 / FX-102(P)-CC2 L 50 50 50 35 35 35 • Length L ( ) () ( ) () 1 1.969 969 1 13 .378 78 8 8 Model No. Length L (mm in) ( ) ( ( ) ) ( ) ( ( ) CN-14A-C1 1,000 39.370 CN-14A-C2 2,000 78.740 CN-14A-C3 3,000 118.110 "3.7"0.146 cable CN-14A-C5 5,000 196.850 All information is subject to change without prior notice. SUNX Limited 2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-(0)568-33-7211 FAX: +81-(0)568-33-2631 Overseas Sales Dept. Phone: +81-(0)568-33-7861 http://www.sunx.jp/ FAX: +81-(0)568-33-8591 Printed on 100% recycled paper PRINTED IN JAPAN No.CE-FX100-10 January, 2007