OCTAGON SYSTEMS 6627
Specifications
ADDRESSING & INTERRUPTS
Jumper–selectable base addresses from 220h to 3E0h. Interrupts selected via jumpers to indicate end of analog conversion. The board can also generate interrupts to transfer digital data into or out of the board, as well as at regular intervals according to a programmable timer on the board. Individual control bits are used to enable each type of interrupt.
ANALOG INPUTS
16 input channels, may be configured as 16 single–ended or 8 differential, 12–bit resolution, Programmable gain, range, and polarity on inputs, Input ranges: Bipolar: ±10V, ±5V, ±2.5V, ±1.25V, Unipolar: 0–10V, 0–5V, 0–2.5V, 100,000 samples per second maximum sampling rate, 512–sample FIFO for reduced interrupt overhead, Autocalibration of all input ranges under software control, Input bias current 50 nA max, Max. input voltage ±10V for linear operation, Overvoltage protection ±35V on any analog input without damage, Nonlinearity ±1 LSB, no missing codes, Conversion trigger software command, internal pacer clock, or external TTL signal
ANALOG OUTPUTS
2 analog output channels with 12–bit resolution, D/A resolution 12 bits (1/4096 of full scale), Multiple fixed full–scale output ranges, including unipolar and bipolar ranges:, Fixed unipolar: 0–5V or 0–10V, Fixed bipolar: ±5V or ±10V, Programmable: 0–10V or ±10V in .01V steps, Autocalibration under software control, Output current ±5 mA max per channel, Settling time 4 µS max. to ±1/2 LSB, Relative accuracy ±1 LSB, Nonlinearity ±1 LSB, monotonic
AUTOCALIBRATION
Circuits calibrated – A/D (all 8 input ranges) and D/A, A/D error after calibration ±1 LSB (typical), ±2 LSB (max), D/A error after calibration ±1 LSB (typical), ±2 LSB (max)
CONNECTORS
50–pin connector for all I/O; connects to C–50–18 cable
COUNTER/TIMERS & A/D TRIGGERING
1 32–bit counter/timer (2 82C54 counters cascaded) for A/D pacer clock and interrupt operation timing, 1 16–bit counter/timer for user counting and timing functions, Pacer clock source: 10 MHz or 1 MHz on–board clock source, General purpose 16–bit down counter (1 82C54 ctr)
DIGITAL I/O
8 dedicated digital outputs, 8 dedicated digital, inputs, TTL compatible, Input current ±1µA max, Output current: logic 0: 64 mA max.; logic 1: –15 mA max., All lines have 10 KO pull–up resistors
ENVIRONMENTAL
–40° to 85° C operating, 5% to 95%, RH, noncondensing
SIZE & POWER
3.550 in. x 3.775 in., PC/104 form factor; compatible with 8–bit bus systems, +5VDC ±10%, 220 mA typical, I/O header ±15V, current ±10 mA max with DACs unloaded, +5V output current limited by PC/104 power supply
SOFTWARE DRIVERS
DOS, Linux 2.4, QNX, & Windows XP, NT, 98
Features
- 100,000 samples per second maximum sampling rate
- 12–bit resolution
- 16 input channels, may be configured as 16 single–ended or 8 differential
- 2 analog output channels with 12–bit resolution
- 512–sample FIFO for reduced interrupt overhead
- 8 dedicated digital outputs, 8 dedicated digital inputs, TTL compatible
- Autocalibration under software control
- D/A resolution 12 bits (1/4096 of full scale)
- Programmable gain, range, and polarity on inputs
Datasheet
Octagon Systems=6627=datasheet1-536428269.pdf
412 KiB
Extracted Text
PC/104 DMM–AT 12–bit A/D D/A module The DMM–AT is a PC/104 data acquisition board that offers 16 total analog inputs with 12–bit resolution and programmable input range; 100,000 samples per second maximum sampling rate with FIFO operation; two ana- log outputs with 12–bit resolution; user–selectable ana- log output ranges; 16 lines of digital I/O (eight lines input, eight lines output); one 32–bit counter/timer for A/D conversion and interrupt timing; and one 16–bit counter/timer for general purpose use. PC/104 cards plug into any system with a PC/104 interface. The DMM–AT also provides autocalibration for both The Octagon family of PC/104 single board computers, analog input and output channels. All calibration adjust- expansion cards, and enclosures provides a complete solu- ments are performed using a TrimDAC. The optimum tion for applications in transportation, security, military, TrimDAC values for each input range are stored in an communications, distributed control, point–of–sale, EEPROM and recalled automatically on power up. ticketing machines, weighing equipment, and other similar applications. The analog input channels on the DMM–AT feature pro- grammable gains of 1, 2, 4, and 8, as well as program- mable unipolar/bipolar range, for a total of nine different input ranges. The 512–sample FIFO enables the board ® to operate at full speed in Windows operating systems using interrupts. Certified Partner program The DMM–AT is an Octagon Certified Partner The two analog output channels have multiple unipolar product, which is guaranteed compatible with and bipolar output ranges. The DACs feature simultane- Octagon CPU cards. The DMM–AT will withstand high ous update capability. A programmable output range shock and vibration, and operates in temperature ranges feature lets you set the output range via software any- from –40° to 85° C. This rugged expansion card will where between 0V to 10V in unipolar and –5V to +5V provide years of reliable service in the most challenging in bipolar modes. environments. A programmable gain amplifier, programmable unipo- lar/bipolar range, and programmable 5V/10V full–scale range combine to give the DMM–AT a total of nine dif- ferent possible analog input ranges. The digital I/O lines are CMOS/TTL compatible. These lines will interface with logic devices, switch inputs, LEDs, and industry–standard opto module racks. Octagon has a variety of opto modules and termination boards for easy access for field wiring. 11 6510 W. 91st Avenue • Westminster CO 80031 • 303–430–1500 www.octagonsystems.com DIGITAL I/O: Features � 8 dedicated digital outputs, 8 dedicated digital ANALOG INPUTS: inputs, TTL compatible � 16 input channels, may be configured as 16 � Input current ±1μA max single–ended or 8 differential � Output current: logic 0: 64 mA max.; � 12–bit resolution logic 1: –15 mA max. � Programmable gain, range, and polarity on inputs � All lines have 10 KΩ pull–up resistors � Input ranges: Bipolar: ±10V, ±5V, ±2.5V, ±1.25V Unipolar: 0–10V, 0–5V, 0–2.5V COUNTER/TIMERS & A/D TRIGGERING: � 100,000 samples per second maximum sampling rate � 1 32–bit counter/timer (2 82C54 counters cascaded) for A/D pacer clock and interrupt operation timing � 512–sample FIFO for reduced interrupt overhead � 1 16–bit counter/timer for user counting and � Autocalibration of all input ranges under timing functions software control � Pacer clock source: 10 MHz or 1 MHz on–board � Input bias current 50 nA max clock source � Max. input voltage ±10V for linear operation � General purpose 16–bit down counter (1 82C54 ctr) � Overvoltage protection ±35V on any analog input without damage AUTOCALIBRATION: � Nonlinearity ±1 LSB, no missing codes � Circuits calibrated – A/D (all 8 input ranges) and D/A � Conversion trigger software command, internal pacer clock, or external TTL signal � A/D error after calibration ±1 LSB (typical), ±2 LSB (max) � D/A error after calibration ±1 LSB (typical), ANALOG OUTPUTS: ±2 LSB (max) � 2 analog output channels with 12–bit resolution � D/A resolution 12 bits (1/4096 of full scale) CONNECTORS: � Multiple fixed full–scale output ranges, including � 50–pin connector for all I/O; connects to unipolar and bipolar ranges: C–50–18 cable Fixed unipolar: 0–5V or 0–10V Fixed bipolar: ±5V or ±10V Programmable: 0–10V or ±10V in .01V steps ADDRESSING & INTERRUPTS: � Autocalibration under software control � Jumper–selectable base addresses from 220h to 3E0h. � Output current ±5 mA max per channel � Interrupts selected via jumpers to indicate end of analog conversion. The board can also generate � Settling time 4 μS max. to ±1/2 LSB interrupts to transfer digital data into or out of the � Relative accuracy ±1 LSB board, as well as at regular intervals according to a programmable timer on the board. Individual control � Nonlinearity ±1 LSB, monotonic bits are used to enable each type of interrupt. 22 6510 W. 91st Avenue • Westminster CO 80031 • 303–430–1500 www.octagonsystems.com ENVIRONMENTAL: SOFTWARE DRIVERS � –40° to 85° C operating � DOS, Linux 2.4, QNX, & Windows XP, NT, 98 � 5% to 95%, RH, noncondensing ORDERING INFORMATION #6627 DMM–AT 12–bit analog, 16–channel, SIZE & POWER: I/O module � 3.550 in. x 3.775 in., PC/104 form factor; compatible with 8–bit bus systems � +5VDC ±10%, 220 mA typical ACCESSORIES ORDERING INFORMATION #6742 C–50–18, 50–conductor 18” ribbon cable � I/O header ±15V, current ±10 mA max with DACs unloaded #6747 STB 104, screw terminal board; mounts directly on PC/104 stack for easily–accessible � +5V output current limited by PC/104 power supply wiring termination 33 6510 W. 91st Avenue • Westminster CO 80031 • 303–430–1500 www.octagonsystems.com
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the 6627 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
Octagon Systems 6375 Digital I/O - 2656 PC/104 digital I/O card, provides 56 digital I/O lines. 48 o...
Octagon Systems 6530 CompactFlash card - The 2852 module is a PC/104–Plus expansion card that provid...
Octagon Systems 6533 CPU Board - XE–900 CPU card, 0 MB, 733 MHz, w/fan, The XE–900 single board comp...
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods