DIMM-PC – ADA3 Short description Rev. 2.2 The following short description is intended to convey a brief overall view of the components. Installation alterna- tives are depicted herein. 1. Connector location CompactFlash @ Ethernet reserved Power Keyboard (from CPU Module) secondary IDE Dot-Matrix Display LPT1 MS / SL select secondary IDE for CompactFlash with activity - LED Battery 3V Link / Activity LEDs for Ethernet Ethernet input Port 80 Debug-Out COM1 DIMM-PC CPU Module Feature COM2 Floppy PC/104 Power primary IDE with activity - LED RESET VCC Con. ISA Con. (Banana Plug) ) GND Con. (Banana Plug) DIMM-PC COM3 I/O Modules POTI (for Dot Matrix Disp.) CRT COM4 Ethernet (from I/O Module) JIPA Link / Activity Display Con. LEDs for Ethernet Backlight Speaker Note: On every through-hole connector, Pin1 is marked with a quadratic pad! Kontron® Embedded Modules GmbH * Brunnwiesenstraße 16 * D-94469 Deggendorf page 1 of 8 pages document: ADA7K122.doc last changend on 18-Dez-03 DIMM-PC – ADA3 2. Connector pinout PC/104- primary secondary PC/104-BUS FLOPPY LPT1 POWER IDE IDE PIN A(X1) B(X1) C(x2) D(x2) X3 X24 X31 X15 X13 0 GND GND 1 IOCHCK# GND SBHE# MEMCS16# GND RESET# RESET# GND STB# 2 SD7 RSTDRV LA23 IOCS16# VCC GND GND NC AFD# 3 SD6 VCC LA22 IRQ10 CODE- SD7 SD7 GND PD0 PIN 4 SD5 IRQ9 LA21 IRQ11 +12V SD8 SD8 NC ERR# 5 SD4 -5V LA20 IRQ12 -5V SD6 SD6 GND PD1 6 SD3 DRQ2 LA19 IRQ15 -12V SD9 SD9 NC INIT# 7 SD2 -12V LA18 IRQ14 GND SD5 SD5 GND PD2 8 SD1 /0WS LA17 DACK0# VCC SD10 SD10 FDCIDX# SLIN# 9 SD0 +12V MEMR# DRQ0 SD4 SD4 GND PD3 10 IOCHRDY GND MEMW# DACK5# SD11 SD11 FDCMTR0# GND 11 AEN SMEMW# SD8 DRQ5 SD3 SD3 GND PD4 12 SA19 SMEMR# SD9 DACK6# SD12 SD12 NC GND 13 SA18 IOW# SD10 DRQ6 SD2 SD2 GND PD5 14 SA17 IOR# SD11 DACK7# SD13 SD13 FDCDS0# GND 15 SA16 DACK3# SD12 DRQ7 SD1 SD1 GND PD6 16 SA15 DRQ3 SD13 VCC SD14 SD14 NC GND 17 SA14 DACK1# SD14 MASTER# SD0 SD0 GND PD7 18 SA13 DRQ1 SD15 GND SD15 SD15 FDCDIR# GND 19 SA12 REFRESH# GND GND GND GND GND ACK# 20 SA11 SYSCLK NC NC FDCSTEP# GND 21 SA10 IRQ7 NC NC GND BUSY# 22 SA9 IRQ6 GND GND FDCWDAT# GND 23 SA8 IRQ5 IOW# /IOW GND PE 24 SA7 IRQ4 GND GND FDCWG# GND 25 SA6 IRQ3 IOR# /IOR GND SLCT# 26 SA5 DACK2# GND GND FDCTRK0# VCC 27 SA4 T/C IOCHRDY IOCHRDY GND 28 SA3 BALE NC NC FDCWPRT# 29 SA2 VCC NC NC GND 30 SA1 OSC GND GND FDCRDATA# 31 SA0 GND IRQ14 IRQ15 GND 32 GND GND IOCS16# IOCS16# FDCHDSEL# 33 SA1 SA1 GND 34 NC NC DSKCHG 35 SA0 SA0 36 SA2 SA2 37 IDE CS0# S_IDE CS0# 38 IDE CS1# S_IDE CS1# 39 HDLED# S_HDLED# 40 GND GND 41 VCC 42 VCC 43 GND 44 NC Kontron® Embedded Modules GmbH * Brunnwiesenstraße 16 * D-94469 Deggendorf page 2 of 8 pages document: ADA7K122.doc last changend on 18-Dez-03 DIMM-PC – ADA3 JIPA DOT-MATRIX Compact ISA Slot Connector DISPLAY Flash PIN X17 (A) X17 (B) X17 (C) X17 (D) X29 X10 X30 0 1 IOCHCK# GND SBHE# MEMCS16# LFS GND GND 2 SD7 RSTDRV LA23 IOCS16# LLCLK GND SD3 3 SD6 VCC LA22 IRQ10 GND VCC (+5V) SD4 4 SD5 IRQ9 LA21 IRQ11 GND VCC (+5V) SD5 5 SD4 -5V LA20 IRQ12 SCLKY VEE (contrast voltage) SD6 6 SD3 DRQ2 LA19 IRQ15 GND VEE (contrast voltage) SD7 7 SD2 -12V LA18 IRQ14 GND AFD_A# S_IDECS0# 8 SD1 ZWS# LA17 DACK0# BLANK# AFD_A# GND 9 SD0 +12V MEMR# DRQ0 NC SLIN_A# GND 10 IOCHRDY GND MEMW# DACK5# NC SLIN_A# GND 11 AEN SMEMW# SD8 DRQ5 P8 INIT_A# GND 12 SA19 SMEMR# SD9 DACK6# P9 INIT_A# GND 13 SA18 IOW# SD10 DRQ6 P0 PD0_AVCC 14 SA17 IOR# SD11 DACK7# P1 PD0_AGND 15 SA16 DACK3# SD12 DRQ7 P2 PD1_AGND 16 SA15 DRQ3 SD13 VCC P3 PD1_AGND 17 SA14 DACK1# SD14 MASTER# P10 PD2_AGND 18 SA13 DRQ1 SD15 GND P11 PD2_A SA2 19 SA12 REF# P18 PD3_A SA1 20 SA11 SYSCLK P19 PD3_A SA0 21 SA10 IRQ7 P4 PD4_ASD0 22 SA9 IRQ6 P5 PD4_ASD1 23 SA8 IRQ5 P6 PD5_ASD2 24 SA7 IRQ4 P7 PD5_A IOCS16# 25 SA6 IRQ3 P12 PD6_AGND 26 SA5 DACK2# P13 PD6_AGND 27 SA4 TC P14 PD7_ASD11 28 SA3 BALE P15 PD7_ASD12 29 SA2 VCC P20 VCC (100 OHM) SD13 30 SA1 OSC P21 VCC (100 OHM) SD14 31 SA0 GND P22 GND SD15 32 P23 GND S_IDECS1# 33 GND GND 34 NC IOR# 35 NC IOW# 36 NC VCC 37 MAD12 IRQ15 38 MAD13 VCC 39 MAD14 MS_SELECT 40 MAD15 NC 41 NC RSTDRV# 42 GND IOCHRDY 43 I2DAT NC 44 I2CLK VCC 45 NC NC 46 NC NC 47 NC SD8 48 NC SD9 49 NC SD10 50 GND GND 51 VCC 52 DA_O0 53 NC 54 NC 55 VDCLK 56 VSYNC 57 HSYNC 58 BLUE 59 GREEN 60 RED 61 SW_BACK 62 VDD_SRC 63 BACK_SRC 64 NC 65 +12V 66 +12V 67 VCC 68 NC 69 NC 70 NC 71 FPVEE 72 VPANEL Kontron® Embedded Modules GmbH * Brunnwiesenstraße 16 * D-94469 Deggendorf page 3 of 8 pages document: ADA7K122.doc last changend on 18-Dez-03 DIMM-PC – ADA3 ETHERNET ETHERNET PS/2 POWER POWER COM 1 COM 2 COM 3 COM 4 (from I/O) (from CPU) KEYBOARD PIN X19 X26 X22 X5 X6 X8 X9X20 X23 0 1TXD+_IO TXD+_CPU KBDATC VCC VCC DCD1#_X DCD2#_X DCD3#_X 485_TXD 2TXD-_IO TXD-_CPU NC GND GND RXD1_XRXD2_XRXD3_XNC 3RXD+_IO RXD+_CPU GND GND +12V TXD1_XTXD2_XTXD3_X 485_TXD- 4 NC NC VCC +12V DTR1#_XDTR2#_XDTR3#_XNC 5 NC NC KBCLKC GND GND GND GND 6RXD-_IO RXD-_CPU NC DSR1#_XDSR2#_XDSR3#_X 485_RXD 7NC NC RTS1#_XRTS2#_XRTS3#_XNC 8NC NC CTS1#_XCTS2#_XCTS3#_X 485_RXD 9 RI1#_XRI2#_XRI3#_XNC 10 SHLDGN SHLDGN SHLDGN SHLDGN CRT Feature Backlight MONITOR Connector PIN X11 X28 X16 0 1 RED VCC /HDLED 2 GREEN SW_BACK VCC 3 BLUE +12V I2DAT 4 NC GND VCC 5 GND GND I2CLK 6 GND NC GND 7 GND BACK_SRC PGOOD 8 GND DA_O0 GND 9 NC NC prg. ChipSelect 10 GND FPBACK external SMI 11 NC reserved 12 NC VCC 13 H-SYNC reserved 14 V-SYNC reserved 15 NC reserved 16 SHLDGND reserved 17 reserved 18 reserved To protect the external power lines of peripheral devices the customer has to take care that: • the wires have the right diameter to withstand the maximum available current • the enclosure of the peripheral device fulfils the fire protecting requirements of IEC/EN 60950. Kontron® Embedded Modules GmbH * Brunnwiesenstraße 16 * D-94469 Deggendorf page 4 of 8 pages document: ADA7K122.doc last changend on 18-Dez-03 DIMM-PC – ADA3 3. Features • One slot for DIMM-PC CPU module • Two slots for DIMM add-on I/O modules • JIPA socket • PC/104-slot • ISA slot • PS/2 Keyboard-header • Western socket for Ethernet 10base-T (from DIMM-IO Module) • Western socket for Ethernet 10base-T and 100base-T (from DIMM-CPU Module) • 44pos. IDE connector on primary channel (pitch 2,00 mm) • 40pos. IDE connector on secondary channel (pitch 2,54mm) • CompactFlash socket on secondary IDE channel (Master/Slave selectable by Jumper) Note: Some CompactFlash Cards may cause problems when used together with other IDE devices • 34pos. Floppy-connector (pitch 2,54mm) • Header for DOT-matrix display • 7-segment LED displays showing outputs on Debug-Port 80 • Piezo electronic speaker • Reset-key • battery (3V CR2032) • 4pos. power connector, 3pos. power connector with screw-terminals • Two mounting holes for banana plug connectors (+5V and GND) • LPT port (25pos. DSUB Connector) • Four serial ports (9pos. DSUB Connector): 3 x RS232-ports (COM1, COM2, COM3); 1 x RS485-port (COM4) • 15pos. VGA-header DSUB Kontron® Embedded Modules GmbH * Brunnwiesenstraße 16 * D-94469 Deggendorf page 5 of 8 pages document: ADA7K122.doc last changend on 18-Dez-03 DIMM-PC – ADA3 3.1. DOT-matrix display A DOT-matrix display can be plugged on the connector X10 as shown in the following drawing: 14 1 16 15 Codepins 16 1 X10 The signals for the display are from the LPT-port. Steps to install the DOT-matrix display: • Turn on or reboot the system • Press if you are asked to enter setup • Change the settings for the LPT port into „extended mode“ • Save the settings and start DOS • Start the program D101LCD (if you use the DIMM-PC D101) or the program D201LCD (if you use the DIMM-PC D201). The correct commando line for the program is: D101LCD COPY 16 2 00 40 00 40 or D201LCD COPY 16 2 00 40 00 40 • Reboot the system again Now the display is ready for use. The LCD driving voltage (contrast) can be changed by the potentiometer R3. Please visit our Homepage (www.jumptec.de) for the programs D101LCD and D201LCD. Note: You can‘t use the DOT-matrix display and a printer at the same time. If you want to use a printer please enter setup again and change the settings for the LPT port into “normal“. Now the DOT-matrix display has no function. Kontron® Embedded Modules GmbH * Brunnwiesenstraße 16 * D-94469 Deggendorf page 6 of 8 pages document: ADA7K122.doc last changend on 18-Dez-03 DIMM-PC – ADA3 3.2. Mechanical: Dimensions (LxWxH): Length 256mm, Width 180mm 3.3. Technical data: Surface temperature: operating 0 bis +60°C (corresponding airflow necessary) storage: -10 bis +85°C relative humidtiy: operating: 10% bis 90% non condensing non operating: 5% bis 95% non condensing 3.4. Electrical characteristics: Supply Voltage: (*1) +5V +12V (if LCD backlight is connected) Supply current: 300mA Note: depending on connected CPU and extension boards the current drawn will be higher! *1: To protect the external powerlines of peripheral devices the customer has to take care about: • that the wires have the right diameter to withstand the maximum available current • that the enclosure of the peripheral device fulfils the fire protecting requirements of IEC/EN 60950. Battery voltage for RTC: 3.0 ... 4.2 V Battery supply current: max. 10 µA 4. Battery Information English: CAUTION ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Deutsch: VORSICHT ! Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch den selben oder einen vom Hersteller empfohlenen gleichwertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. French: ATTENTION ! Risque d'explosion avec l'échange inadéquat de la batterie. Remplacement seulement par le même ou un type équivalent recommandé par le producteur. L'évacuation des batteries usagées conformément à des indications du fabricant. Danish: ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig Håndtering. Udskifting må kun ske med batteri af samme fabrikant og type. Lever det brugte batteri tilbage til leverand∅ren. Finnish: VAROITUS ! Paristo voi rãjãhtãã, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laltevalmistajan suosittelmaan tyyppiln. Havita kaytetty paristo valmistajan ohjeiden mukaisesti. Spanish: Precaución ! Peligro de explosión si la batería se sustituye incorrectamente. Sustituya solamente por el mismo o tipo equivalente re- comendado por el fabricante. Disponga las baterías usadas según las instrucciones del fabricante. Note: The battery of this product is not considered to be accessible by the end user. Therefore the safety instructions are only given in English, German, French, Danish, Finish and Spanish language. If the battery of this product however is accessible by the end user, it is in the responsibility of the Kontron customer to give the corresponding safety instructions in the required language(s). Kontron® Embedded Modules GmbH * Brunnwiesenstraße 16 * D-94469 Deggendorf page 7 of 8 pages document: ADA7K122.doc last changend on 18-Dez-03 DIMM-PC – ADA3 5. Document history: date Doc. name doc. author Action rev. 16.05.98 ADA7K110.DOC 1.0 F. Krauss Short description created 26.11.98 ADA7K111.DOC 1.1 F. Krauss Changed commando line for DOT-matrix display, changed GmbH into AG. 12.01.99 ADA7K112.DOC 1.2 M. Wiesmüller Layout revised, created new graphics, missing informa- tion added. 30.04.99 ADA7K113.DOC 1.3 F: Krauss Delete all references to a manual 05.04.02 ADA7K120.DOC 2.0 J. Baumgartner All infos according to HW Rev. 2.x 24.06.02 ADA7k121.DOC 2.1 J. Baumgartner security infos added, references to USB removed 11.12.03 ADA7k122.DOC 2.2 D. Gunter Changed to Kontron logo. Added battery information section. Kontron® Embedded Modules GmbH * Brunnwiesenstraße 16 * D-94469 Deggendorf page 8 of 8 pages document: ADA7K122.doc last changend on 18-Dez-03