Surge Protective Devices HS Models GENERAL SPECIFICATIONS Description: Series or parallel wired, terminal strip connected, Multi-stage hybrid Active Tracking Network ® (ATN ) sine wave tracking surge protective device. Application: Dedicated AC and DC power circuits operating at 5-275 VAC/5-300 VDC, ≤10 amps, feeding variable speed drives, variable frequency drives, process controllers, PLCs, power supplies, micro-processor based loads, CNCs and a wide variety of other mission critical and general purpose individual loads. Warranty: Ten-Year Free Replacement Unit Listings: Recognized components under UL1449 Second Edition (certain models, see table other side), UL1283, CSA Manufacturer Qualifications: ISO 9001:1994 Quality System Certification BSI FM 30833 MECHANICAL SPECIFICATIONS Enclosure: ABS Plastic UL94-5VA 2 Connection: Wire clamping box terminals; Minimum 22 AWG (0,34 mm ) wire size – Maximum 12 AWG 2 (4,0 mm ) wire size Weight: ≈ 1 lb (.45 kg) Operating Temperature: -40° F (-40° C) to +140° F (+60° C) ELECTRICAL/PERFORMANCE SPECIFICATIONS Protection Modes: All Mode: Dedicated L-N (normal mode), Dedicated L-G, N-G (common mode) Input Power Frequency: 0-64 Hz (AC) Response Time: Active <1 nanosecond Maximum EMI/RFI Attenuation – Mil-Std-220 Maximum 1 kHz 10 kHz 100 kHz 1 MHz 10 MHz Attenuation Frequency 0 dB 10 dB 29 dB 31 dB 12 dB 33 dB @ 80 MHz Maximum Continuous Operating Current: 10 Amps rms up to 250 volts Short Circuit Current Rating: 200 kAIC when protected by class R, 10 Amp fuse 843F ©2003 Specifications subject to change (hs10adim.wmf; hss.doc 2/11/03) ZM02-352 15470 Flight Path Drive, Brooksville, Florida 34604 USA Page 1 of 2 www.itvss.com - 800-647-8877 – 352-799-0713 Surge Protective Devices HS Models IT Part# 420-9000 Universal Mounting Bracket & Din Rail Clip HS 10 Amp unit 1.25[32] 4.60[117] Dimensions are in inches[mm] ANSI/IEEE C62.41-1991 Measured Limiting Voltage* UL SVR A1 A3 B3/C1 UL 1449-2 Peak Surge Nominal System Ring Wave Ring Wave Impulse Wave Suppressed Available Models Current Voltage 2 kV, 67 A 6 kV, 200 A 6 kV, 3 kA Voltage 180° Phs Angle 90° Phs Angle 90° Phs Angle Ratings L-N L-N L-N L-N (AC-Vrms, DC-Vpk) L-G, N-G L-G, N-G L-G, N-G L-G, N-G 5-30 VAC 70 60 170 **HS-24-10A 25 kA **N/A 5-38 VDC 100, 80 80, 60 210, 220 24-50 VAC 80 60 190 **HS-48-10A 25 kA **N/A 24-65 VDC 120, 80 110, 70 230, 220 48-150 VAC 80 330 450 400 HS-120-10A 40 kA 843F 48-200 VDC 120, 60 400, 180 550, 510 400, 400 120-275 VAC 80 530 830 800 HS-250-10A 40 kA 843F 120-300 VDC 140, 80 690, 230 940, 890 800, 800 *Test Environment: Positive polarity. HS-24-10A & HS-48-10A tested static, others tested with AC power applied. All units tested at terminals, time base = 1 ms. All measurements referenced from zero volts per NEMA LS-1. ® **Underwriters Laboratories (UL ) does not list TVSS products designed to operate below 120 Vrms, static test only, phase angle does not apply. 843F ©2003 Specifications subject to change (hs10adim.wmf; hss.doc 2/11/03) ZM02-352 15470 Flight Path Drive, Brooksville, Florida 34604 USA Page 2 of 2 www.itvss.com - 800-647-8877 – 352-799-0713 4.41[112] 5.21[132]