XPort1011 Multi-Protocol Four Port Serial PCI Card Based on the MPC8260 PowerQUICC II™ Series Features MPC8250 At Up To 300MHz with Integrated PCI Four SCCs Support a Broad Range of Serial Protocols Software Configurable Serial Interface Modes Front I/O 8-256MB SDRAM 4-16MB Soldered Flash 512KB Socketed Flash 2 KB SEEPROM XPort1011 is an intelligent communications controller targeting high performance yet low cost applications. XPort1011 combines a wide array Two RS-232 SMC Ports of supported serial protocols, a broad range of serial interface standards, VxWorks Driver and BSP and a flexible I/O routing structure, to pack maximum flexibility into an industry standard PCI card. Linux LSP Windows NT/2000/XP Driver Powered by the MPC8250 (PowerQUICC II™), XPort1011 implements four serial communication ports providing a EIA-530-A compliant signal set. Supporting HDLC/SDLC, UART, Transparent and BISYNC modes, Typical Applications with NRZ, NRZI, FM0, FM1, Manchester and Differential Manchester encoding. Coupled with software configurable support for RS-232, LAN/WAN Networking RS-422, RS-423, RS-485 and MIL-STD-188-114, XPort1011 provides Military Communications maximum flexibility for your application. Telecommunication For solutions which require low cost but high performance, the XPort1011 Management Network is also available in configurations which provide a 7-wire signal set. This Data and Legacy System configuration implements four serial communication ports providing TXD, Communications RXD, TXC, RXC, RTS, CTS and DCD flow control, with software configurable support for RS-232, RS-422, RS-423, and RS-485. Data Acquisition Process Control As a system designer, XPort1011 will help drive both cost and power consumption out your system. Because the PCI bridge is integrated on chip, XPort1011 draws up to 40% less power, and costs up to 30% less than conventional designs based on other processors. For more information on XPort1011: Extreme Engineering Solutions... Visit: http://www.xes-inc.com/ Call: 608-833-1155 ...Always Fast E-mail: sales@xes-inc.com Block Diagram Processor Serial Communication Controller Serial Interface (7 Wire) (cont.) • MPC8250 PowerQUICC II (cont.) • 7 Wire Interface • Embedded PowerPC G2 Core • DPLL supporting NRZ, NRZI, • DTE/DCE Mode Cable • 133-300Mhz FM0, FM1, Manchester and Selectable • 280 Dhrystones at 200Mhz Differential Manchester Software • 66MHz 60x Bus • Independent BRG’s for each • VxWorks BSP • 16KB Instruction and Data SCC transmitter and receiver • SCC and SMC Caches • Optional External Custom • Linux LSP • 32KB internal SRAM Oscillators • Integrated MMU Physical Serial Interface (Standard) • Integrated Floating Point Unit • PCI Form Factor • Software Configurable Drivers • Core Disabled Mode supported for RS-232, RS-422, RS-423, Power Requirements (Typical) Memory RS-485, and MIL-STD-188-114 • +3.3V 0.60A 1.98W • 32-256MB SDRAM Balanced/Unbalanced Type 1 • +5.0V 0.35A 1.75W • SDRAM doubles as 8MB of and 2 Modes • +12.0V 0.012A 0.15W buffer storage in Core Disabled • 10Mbps Max Synchronous • -12.0V 0.012A 0.15W Mode • 4Mbps Max Asynchronous Operating Temperature • 4-16MB Surface Mount Flash • EIA-530-A DTE/DCE Cable • 0 to +55C ambient, at board • 512KB Socketed Flash Selectable • 2 KB Serial EEPROM Humidity Serial Interface (7 Wire) • 0% to 85% Serial Communication Controller • Software Configurable Drivers • HDLC, UART, Transparent and for RS-232, RS-422, RS-423, Storage Temperature BISYNC modes and RS-485 • -40 to +70C • 10Mbps Max Synchronous • 4Mbps Max Asynchronous Copyright 2006, X-ES Phone: 608-833-1155 DS90020015-B Extreme Engineering Solutions, Inc. Fax: 608-827-6171 3225 Deming Way, Suite 120 Web: http://xes-inc.com Middleton, WI 53562 E-mail: sales@xes-inc.com