Dual XMC/PMC Carrier Board RoHS 2002/95/EC APPLICATIONS The PP XMC/202 XMC/PMC carrier board provides a Communications Controllers. Hot Swap support enables flexible solution for designers wishing to add live insertion and extraction of the PP XMC/202 so that functionality to 6U CompactPCI® systems in using XMC or I/O and network interfaces can be added, replaced or PMC modules. The carrier can accommodate two single or upgraded without interruption to the system operation. Rear I/O signals from each of the XMC/PMC sites are one dual width, PMC or XMC modules conforming to the IEEE 1386 Common Mezzanine Card standard. PMC routed to the CompactPCI J3 and J5 connectors and modules supporting up to 66 MHz PCI/PCI-X or XMC there is an optional rear panel I/O Transition Module. modules supporting up to x4 PCI Express® interfaces can Options to operate in temperatures ranging from -40°C be used. A wide range of XMC/PMC modules can be to +85°C are available. Ruggedized conduction-cooled supported such as SAS, SATA, LAN, WAN, Graphics and and ruggedized air-cooled versions are also planned. HIGHLIGHTS � Supports 2 single size XMC or PMC modules (or as one � Occupies one 6U CompactPCI slot: dual width module) - 5 Volt or 3.3 Volt signaling - 32/64-bit and 33/66 MHz � A single PMC and a single XMC module can be used simultaneously � "Hot Swap” live insertion and extraction � XMC module interface supports: � Extended temperature versions supported: - x1, x2 or x4 PCI Express - -25°C to +70°C (E-Series) � PMC module interface supports: - -40°C to +85°C (K-Series, includes humidity sealant) - 5 Volt or 3.3 Volt signaling � Ruggedized versions planned: - 32/64-bit and 33/66 MHz PCI/PCI-X - conduction cooled and air cooled � Front panel I/O, and rear I/O via J3 and J5 connectors: � A Rear Transition Module is available - rear I/O routed as differential pairs - rear I/O options for XMC Pn6 or PMC Pn4 connectors � 3.3 Volt, 5 Volt, +12 Volt and -12 Volt provided for XMC and PMC modules via CompactPCI backplane 4 Gilberd Court, Colchester, Essex, CO4 9WN, UK CONCURRENT Tel: +44 (0)1206 752626 Fax: +44 (0)1206 751116 6 Tower Office Park, Woburn, MA 01801, USA TECHNOLOGIES Tel: (781) 933 5900 Fax: (781) 933 5911 Front Panel Blue XMC and PMC Interfaces Latch LED � Supports 2 single size XMC or PMC modules (or as one dual width module): � a single PMC and a single XMC module can be used simultaneously � supports non-Monarch Processor XMC/PMC modules � XMC module interface requirements: � x1, x2 or x4 PCI Express � logical and electrical layer meets specification PCI Express 1.1 PCI to PCIe x4 Bridge Pericom PI7C9X130 � PMC module interface requirements: � 5 Volt or 3.3 Volt signaling x4 PCI to PCIe Bridge Pericom PI7C9X130 � 32/64-bit and 33/66 MHz PCI/PCI-X � logical and electrical layer meets CPCI Hot Swap Bridge Control specification PCI-X 1.0 PLX PCI6540 � complies with CMC (Common Mezzanine Card) standard IEEE 1386-2001 and PMC (PCI Mezzanine Card) standard IEEE 1386.1-2001 � front panel I/O, and rear I/O via J3 and J5 Rear I/O Rear I/O CPCI CompactPCI Bus connectors:- Hot Swap � 64 I/O signals per XMC/PMC site � rear I/O routed as differential pairs � rear I/O options for XMC Pn6 or PMC Pn4 Environmental Specification connectors � operating temperatures:- � can connect to an optional Rear Transition � 0°C to +55°C (N-Series) Module (AD PP5/002) � -25°C to +70°C (E-Series) � -40°C to +85°C (K-Series) Hot Swap Function � storage temperature: -40°C to +85°C � permits live insertion and extraction of PP XMC/202 carrier � 5% to 95% Relative Humidity, non condensing (operating or storage):- � supports Basic and Full Hot Swap � K-Series includes humidity sealant � compatible with PICMG® 2.1, Rev 2.0 Hot � ruggedized versions planned, see separate Swap specification datasheets:- � Hot Swap capable register:- � conduction-cooled: PP XMC/202-RC � insertion � air-cooled: PP XMC/202-RA � extraction � ENUM mask/enable Safety � front panel blue LED � PCB (PWB) manufactured with flammability � CompactPCI backplane interface signals:- rating of 94V-0 � ENUM (board insertion/extraction Mechanical Specification indication) � 6U form-factor: 9.2” x 6.3” � healthy (power) (233.4mm x 160mm) CompactPCI Bus Interface � utilizes a single CompactPCI slot: 0.8” � occupies one 6U CompactPCI slot (20.3mm) � conforms to PICMG 2.0 R3.0:- � connectors: IEC-1076-4-101 for J1, J2, J3, J5 � supports 3.3V and 5V signaling � shock: � 32/64-bits at 33/66 MHz 20g, 11ms, ½ sine (operating); � PLX Technology PCI 6540 PCI to PCI bridge 30g, 11ms, ½ sine (non-operating) � vibration: Other Features 5Hz-2000Hz at 2g, 0.38mm peak displacement � front panel activity LED:- (operating); � flashes with on-board PCI bus activity 5Hz-2000Hz at 5g, 0.76mm peak displacement � front panel fault LED:- (non-operating) � reports power fault or PCI bus error conditions Electrical Specification � +5V@0.0A; +5%/-3% � +3.3V@1.0A; +5%/-3% � +12V@0.002A; � -12V@0.0A � all figures are typical � maximum power per XMC module is 25 Watts ORDERING INFORMATION Order Number Product Description (Hardware) Replace the order number suffix (xy) with selections from the following: PP XMC/202-xy Dual XMC/PMC Carrier Board 10 - Dual XMC/PMC carrier with rear I/O via PMC Pn4 rear I/O connectors 20 - Dual XMC/PMC carrier with rear I/O via via XMC Pn6 rear I/O connectors AD PP5/002-00 Rear Transition Module with front panel I/O interface AD PP5/003-00 Rear Transition Module with PIM sites For extended temperature E and K-Series, please contact your local sales office For ruggedized versions, see separate datasheets: PP XMC/202-RC (conduction-cooled) or PP XMC/202-RA (air-cooled All companies and product names are trademarks of their respective organizations. Datasheet Code 1588/0509 Specification subject to change; E and OE. RoHS 2002/95/EC compliant. © Concurrent Technologies 2009 XMC 64-bit Rear I/O PMC/XMC Module 2 XMC 64-bit Rear I/O PMC/XMC Module 1 64-bit PCI-66 J1 & J2 PCI/PCI-X 33/66