Dual PMC Carrier Board RoHS 2002/95/EC APPLICATIONS The PP PMC/202-U PMC carrier board provides a flexible Hot Swap support enables live insertion and extraction solution for designers wishing to add functionality to of the PP PMC/202-U so that I/O and network interfaces 32/64-bit (33/66 MHz) CompactPCI® systems using PMC can be added, replaced or upgraded without interruption modules. The carrier can accommodate two single or one to the system operation. I/O signals from each of the dual width, 32/64-bit (33/66 MHz), PMC modules PMC sites are routed to the CompactPCI J3 and J4 or J5 conforming to the IEEE 1386 Common Mezzanine Card connectors allowing access from the rear of the system. standard. A wide range of commercial and proprietary Front panel access is supported and there is an optional designed PMC modules can be supported such as SCSI, rear panel I/O Transition Module. LAN, WAN, Graphics and Communications Controllers. HIGHLIGHTS � Supports 2 single size PMC modules or one dual width module: - 5 Volt or 3.3 Volt signaling - 32/64-bit and 33/66 MHz � "Hot Swap” live insertion and extraction � I/O via front panel and rear I/O via J3 and J4 or J5 connectors: - rear I/O routed as differential pairs � 3.3 Volt, 5 Volt, +12 Volt and -12 Volt provided for PMC modules via CPCI backplane � Extended temperature versions available: - -25°C to +70°C (E-Series) � Occupies one 6U CompactPCI slot: - 5 Volt or 3.3 Volt signaling - 32/64-bit and 33/66 MHz 4 Gilberd Court, Colchester, Essex, CO4 9WN, UK CONCURRENT Tel: +44 (0)1206 752626 Fax: +44 (0)1206 751116 3840 Packard Road, Ann Arbor, MI 48108, USA TECHNOLOGIES Tel: (734) 971 6309 Fax: (734) 971 6350 PMC Interfaces Blue Front Panel Front Panel LED � support for 2 single width modules or one dual Latch I/O I/O width module:- � 5 Volt or 3.3 Volt signaling � 32/64-bit and 33/66 MHz PCI interface � supports dual function modules PMC 2 PMC 1 � supports non-Monarch Processor PMC modules 5V or 3.3V � complies with CMC (Common Mezzanine Card) Selectable standard IEEE 1386-2001 and PMC (PCI 32/64-bit Secondary PCI Bus Mezzanine Card) standard IEEE 1386.1-2001 � I/O can be accessed via front panel � I/O can also be accessed via rear through Hot Swap CPCI backplane connectors:- Bridge Control � 64 I/O signals per PMC site 32/64-bit � PMC rear I/O connects via J3 and J4 or J3 Primary PCI and J5 Bus � PMC rear I/O routed as differential pairs to J1 & J2 support SCSI rear I/O CompactPCI Bus J3 J3 J4 J5 CPCI � can connect to a Transition Module Hot Swap To AD PP2/001 (AD PP2/001) � logical layer based on PCI protocol specification � electrical layer based on PCI electrical Safety specification � PCB (PWB) manufactured with flammability rating of 94V-0 Hot Swap Function � permits live insertion and extraction of Mechanical Specification PP PMC/202-U carrier � 6U form-factor: 9.2” x 6.3” � supports Basic and Full Hot Swap (233.4mm x 160mm) � compatible with PICMG® 2.1, Rev 2.0 Hot � utilizes a single CPCI slot: 0.8” (20.3mm) Swap specification � connectors: IEC-1076-4-101 for J1, J2, J3, � Hot Swap capable register:- J4, J5 (not all fitted) � insertion � shock: � extraction 20g, 11ms, ½ sine (operating); � ENUM mask/enable 30g, 11ms, ½ sine (non-operating) � front panel blue LED � vibration: 5Hz-2000Hz at 2g, 0.38mm peak displacement � CPCI backplane interface signals:- (operating); � ENUM (board insertion/extraction 5Hz-2000Hz at 5g, 0.76mm peak displacement indication) (non-operating) � healthy (power) CompactPCI Bus Interface � conforms to PICMG 2.0 R3.0:- � supports 3.3V and 5V signaling � 32/64-bits at 33/66 MHz � PLX Technology PCI 6254 PCI to PCI bridge Other Features � front panel activity LED:- � flashes with on-board PCI bus activity � front panel fault LED:- � reports power fault or PCI bus error conditions Electrical Specification � +5V@0.2A; +5%/-3% � +3.3V@0.6A; +5%/-3% PMC 2 PMC 1 � +12V@0.03A; � -12V@0.01A (0.0A if no PMC module requires -12V) Environmental Specification � operating temperatures:- � 0°C to +55°C (N-Series) � -25°C to +70°C (E-Series) J1 J2 J3 J4 � 10% to 95% Relative Humidity (operating) Drawing of PP PMC/202-01U � -40°C to +70°C (storage) � 10% to 95% Relative Humidity (storage) ORDERING INFORMATION Order Number Product Description (Hardware) Replace the order number suffix (xy) with selections from the following: PP PMC/202-xyU PMC Carrier Board for CPCI 01 - Dual PMC with rear I/O via J3 & J4 (can be used with AD PP2/001-00) (J5 not fitted) 05 - Dual PMC with rear I/O via J3 & J5 (J4 not fitted) AD PP2/001-00U Transition Module (for use with PP PMC/202-01U) For extended temperature operation, E-Series, please contact your local sales office All companies and product names are trademarks of their respective organizations. Datasheet Code 1526/0906 Specification subject to change; E and OE. RoHS 2002/95/EC compliant. © Concurrent Technologies 2006 64-bit Rear I/O 64-bit Rear I/O