HS-1745 Intel® Core™ 2 Duo/Core™ Duo/ Core™ Solo processor mITX Board •CompactFlash•Mini PCI• •PCI-E/PCI Slot•DVI/CRT/LVDS•TV-Out• •Dual GB LAN•Audio•SPDIF•SATA• •ATA/33/66/100•RS-232/422/485• •6 COM•IrDA•USB2.0•WDT•H/W Monitor• Copyright Disclaimers The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for any infringements of patents or other rights resulting from its use. The manufacturer will not be responsible for any direct, indirect, special, incidental or consequential damages arising from the use of this product or documentation, even if advised of the possibility of such damage(s). This manual is copyrighted and BOSER Technology Co., Ltd. reserves all documentation rights. Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. BOSER Technology Co., Ltd. reserves the right to change or improve the contents of this document without due notice. BOSER Technology Co., Ltd. assumes no responsibility for any errors or omissions that may appear in this manual, nor does it make any commitment to update the information contained herein. Trademarks Trademarks Trademarks BOSER is a registered trademark of BOSER Technology Co., Ltd. ISB is a registered trademark of BOSER Technology Co., Ltd. Intel is a registered trademark of Intel Corporation. Award is a registered trademark of Award Software, Inc. AMI is a registered trademark of AMI Software, Inc. All other trademarks, products and or product names mentioned herein are mentioned for identification purposes only, and may be trademarks and/or registered trademarks of their respective companies or owners. © Copyright 2008 BOSER Technology Co., Ltd. All Rights Reserved. Edition 1.5, May 15, 2009 Table of Contents Chapter 1 General Description ..................................1 1.1 Major Features....................................................................... 2 1.2 Specifications ........................................................................ 2 1.3 Board Dimensions................................................................. 4 Chapter 2 Inpacking ...................................................5 2.1 Opening the Delivery Package............................................. 5 2.2 Inspection............................................................................... 5 Chapter 3 Hardware Installation ..............................7 3.1 Before Installation ................................................................. 7 3.2 Board Layout ......................................................................... 8 3.3 Jumper List ............................................................................ 9 3.4 Connector List ..................................................................... 10 3.5 Configuring the CPU ........................................................... 10 3.6 System Memory................................................................... 11 3.7 VGA Controller .................................................................... 11 3.8 PCI E-IDE Drive Connector................................................. 13 3.9 Serial ATA Connector ......................................................... 14 3.10 Floppy Disk Drive Connector............................................. 15 3.11 Parallel Connector............................................................... 16 3.12 Serial Port Connectors ....................................................... 16 3.13 Ethernet Connector............................................................. 18 3.14 USB Connector.................................................................... 18 3.15 CMOS Data Clear................................................................. 19 3.16 Power and Fan Connectors................................................ 19 3.17 Keyboard/Mouse Connectors ............................................ 20 3.18 System Front Panel Control............................................... 20 3.19 IrDA Function....................................................................... 21 3.20 Watchdog Timer .................................................................. 21 3.21 TV-Out Function .................................................................. 22 3.22 Audio Connectors ............................................................... 23 3.23 CompactFlash Connector................................................ 23 3.24 Expansion Slot..................................................................... 25 3.25 8-bit I/O Function................................................................. 25 Chapter 4 AMI BIOS Setup.....................................29 4.1 Starting Setup...................................................................... 29 4.2 Using Setup ......................................................................... 30 4.3 Main Menu............................................................................ 31 4.4 Advanced Settings.............................................................. 32 4.5 Advanced PCI/PnP Settings............................................... 38 4.6 Boot Settings....................................................................... 39 4.7 Security Settings ................................................................. 40 4.8 Advanced Chipset Settings................................................ 40 4.9 Exit Options ......................................................................... 42 Chapter 5 Software Utilities.....................................43 5.1 IDE Driver Installation......................................................... 43 5.2 VGA Driver Installation ....................................................... 47 5.3 Audio Driver Installation..................................................... 50 5.4 LAN Driver Installation........................................................ 53 Declaration of Conformity -- CE Mark BOSER Technology hereby acknowledges that compliance testing in accordance with applicable standards of the EU’s EMC Directive, 89/336/EEC, was successfully completed on a sample of the equipment identified below: Equipment Class: Information Technology Equipment Product Model Series: HS-1745 This Product Complies With: EN55022: Class A for Radiated emissions EN50082-2: Heavy Industrial EMC Immunity We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Manufacturer: BOSER TECHNOLOGY CO., LTD. Safety Instructions Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: � Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. � Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This helps to discharge any static electricity on your body. � Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components. Fasten the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please wear and connect the strap before handle the product to ensure harmlessly discharge any static electricity through the strap. � Please use an anti-static pad when putting down any components or parts or tools outside the computer. You may also use an anti-static bag instead of the pad. Please inquire from your local supplier for additional assistance in finding the necessary anti-static gadgets. NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC PROTECTIONS. Chapter 1 General Description The HS-1745 is an Intel® 945GME GMCH chipset-based board designed. The HS-1745 is an ideal all-in-one mITX board. Additional features include an enhanced I/O with CF, DVI/CRT/LVDS, TV-Out, dual Giga LAN, audio, SPDIF, SATA, 6 COM, IrDA, and USB2.0 interfaces. Designed with the Intel® 945GME GMCH, the board supports Intel® Core™ 2 Duo/Core™ Duo/Core™ Solo processor 1.66~2.33GHz. Its onboard ATA/33/66/100 to IDE drive interface architecture allows the HS-1745 to support data transfers of 33, 66 or 100MB/sec. to one IDE drive connection. The Intel® ICH7-M serial ATA controller with two ports supporting transfer rates up to 150MB/sec. Onboard Intel® 945GME GMCH for CRT display with DVMT or CHRONTEL 7307 for DVI display supporting up to 2048 x 1536. It also supports 18-bit single channel/36-bit dual channel LVDS interface. System memory is also sufficient with the one SO-DDRII socket that can support up to 1GB. Additional onboard connectors include an advanced USB2.0 port providing faster data transmission. And two external RJ-45 connectors for 10/100 Based Ethernet use. To ensure the reliability in an unmanned or standalone system, the watchdog timer (WDT) onboard HS-1745 is designed with software that does not need the arithmetical functions of a real-time clock chip. If any program causes unexpected halts to the system, the onboard WDT will automatically reset the CPU or generate an interrupt to resolve such condition. 1 1.1 Major Features The HS-1745 comes with the following features: � Intel® Core™ 2 Duo/Core™ Duo/Core™ Solo processor 1.66~2.33GHz � One SO-DIMM up to 1GB DDR2 SDRAM � Intel® 945GME/ICH7-M chipset, W83627EHG super I/O chipset � Intel® 945GME or CHRONTEL 7307 DVI graphics, dual Intel® 82573L GB Ethernet, ALC202A audio Codec controller � 18-bit single channel/36-bit dual channel LVDS panel display interface � CF, SPDIF, SATA x 2, COM x 6, USB2.0 x 8, PCIex1 slot, mini PCI slot, 3.3V PCI slot � TV-Out, 8-bit I/O, H/W Monitor function 1.2 Specifications System � CPU: Intel® Core™ 2 Duo/Core™ Duo/Core™ Solo processor 1.66~2.33GHz Celeron® M: 410, 420, 430, 440, 450 Core™ Duo: T2300, T2400, T2500, T2600, T2700 Core™ 2 Duo: T5500, T5600, T7200, T7400, T7600 � FSB: 667/533MHz FSB � BIOS: AMI PnP Flash BIOS 2 � System Chipset: Intel® 945GME GMCH/ICH7-M � I/O Chipset: Winbond W83627EHG � System Memory: 1 x 200-pin SO-DIMM socket up to 1GB DDR2 SDRAM � Storage: 1 x Type II CF socket � Watchdog Timer Software programmable time-out intervals from 1~255 sec. � H/W Status Monitor: Monitoring temperatures, voltages, and cooling fan status � Expansion: 1 x PCIex1 slot 1 x Type III mini PCI slot 1 x 3.3V PCI slot I/O Interface � MIO: 4 x RS-232 2 x RS-232/422/485 8 x USB2.0 (4 x internal, 4 x external) 1 x IDE 1 x FDD 1 x Parallel 2 x SATA 1 x PS/2 for KB/MS 1 x IrDA (only PCB v0.5 or above) � DI/O: 8-bit input/output by parallel port Display � Chipset: Intel® 945GME integrated Intel® GMA950 � LVDS: 18-bit single channel/36-bit dual channel � TV-Out: Provides PAL or NTSC TV systems � DVI: Chrontel 7307 (optional) Audio � Chipset: RealTek ALC202A � Audio Interface: MIC In, Line Out, Line In, SPDIF 3 Ethernet � Chipset: Dual Intel® 82573L GB 10/100/1000 Mbps LAN � Ethernet Interface” RJ-45 x 2 Mechanical & Environmental � Operating Temperature: 0~60 degrees C � Operating Humidity: 0~95%, non-condensing � Size (L x W): 170 x 170 mm 1.3 Board Dimensions 4 Chapter 2 Unpacking 2.1 Opening the Delivery Package The HS-1745 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures. 2.2 Inspection After unpacking the board, place it on a raised surface and carefully inspect the board for any damage that might have occurred during shipment. Ground the board and exercise extreme care to prevent damage to the board from static electricity. Integrated circuits will sometimes come out of their sockets during shipment. Examine all integrated circuits, particularly the BIOS, processor, memory modules, ROM-Disk, and keyboard controller chip to ensure that they are firmly seated. The HS-1745 delivery package contains the following items: � HS-1745 Board x 1 � Utility CD Disk x 1 � Cables Package x 1 � Jumper Bag x 1 � User’s Manual 5 Cables Package NO. Description QTY. 1 COM DB9-10P (2.0-pitch) 1 2 Print DB25-26P(2.0-pitch) 1 3 1-to-2 Mini DIN cable 1 4 SATA device cable 1 5 34P(2.54)*3 FDC cable 1 It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product. In case you discover any missing and/or damaged items from the list of items, please contact your dealer immediately. Option Accessories NO. Description 1 1-to-2 USB cable with bracket 2 COM DB9-10P (2.0-pitch) 3 SATA power cable 4 Pentium® Cooler (251-10310002G) 5 40-pin to 44-pin IDE flat cable 6 Chapter 3 Hardware Installation This chapter provides the information on how to install the hardware using the HS-1745. This chapter also contains information related to jumper settings of switch, and watchdog timer selection etc. 3.1 Before Installation After confirming your package contents, you are now ready to install your hardware. The following are important reminders and steps to take before you begin with your installation process. 1. Make sure that all jumper settings match their default settings and CMOS setup correctly. Refer to the sections on this chapter for the default settings of each jumper. (Set JP6 open) 2. Go through the connections of all external devices and make sure that they are installed properly and configured correctly within the CMOS setup. Refer to the sections on this chapter for the detailed information on the connectors. 3. Keep the manual and diskette in good condition for future reference and use. 7 3.2 Board Layout Top Side 8 Solder Side 3.3 Jumper List Jumper Default Setting Setting Page JP5 CF Use Master/Slave Select: Slave Open 23 JP6 Clear CMOS: Normal Operation Open 19 JP23 COM 3/COM 4 Use RS-232 or Open 16 RS-422/485 Select: RS-232 JP24 Open 16 JP25 Panel Voltage Select: +3.3V Short 2-3 11 JP26 FSB Frequency Select: 667MHz Open 10 9 3.4 Connector List Connector Definition Page ATX1 20-pin ATX Power In Connector 19 CN1 PS/2 6-pin Mini DIN KB/MS Connector 20 CN2 TV-Out Connector 22 CN3 SPDIF Connector 23 CN4 15-pin CRT Connector & COM 1 (DB9) 11/16 CN5/CN6 RJ-45 & Dual USB2.0 Port 18 CN7/CN9 Serial ATA Connector 14 CN8 MIC In/Line Out Connector 23 CN10 External Audio Connector 23 CN11 IDE Connector 13 CN12 Floppy Connector 15 CN13 System Front Panel Control 20 CN14 CompactFlash Connector 23 CN15 SO-DDRII Socket 11 CN16 Mini PCI Slot 25 JP1 Inverter Power In Connector 11 JP2 6-pin KB/MS Connector 20 JP3/JP4 Fan Power In Connector 19 JP9 Wake On LAN Connector 18 JP10/JP11 Internal USB2.0 Port 18 JP12~JP16 COM 2~COM 6 Connector (5x2 header) 16 JP17 8-bit I/O Port 25 JP18/JP19 LVDS Panel Connector 11 JP27 IrDA Connector 21 CON1 x1 PCI-E Slot 25 J1 DVI Connector 11 J2/J3 RS-422/485 Connector 16 LPT1 Parallel Port 16 PCI1 Standard PCI Slot 25 3.5 Configuring the CPU The HS-1745 provides with Intel® Core™ 2 Duo/Core™ Duo/Core™ Solo processor 1.66~2.33GHz. User don’t need to adjust the frequently and check speed of processor. 10 � JP26: FSB Frequency Select Options Settings 1 533MHz FSB Short 2 667MHz FSB (default) Open 3.6 System Memory The HS-1745 provides one SO-DDRII socket at locations CN15. The maximum capacity of the onboard memory is 1GB. 3.7 VGA Controller The HS-1745 provides two connection methods of a VGA device. CN4A offers a single standard CRT connector and JP18/JP19 are the LVDS interface connectors onboard reserved for flat panel installation. � CN4A: CRT Connector PIN Description PIN Description 1 Red 2 Green 3 Blue 4 N/C 6 11 1 5 GND 6 GND 7 GND 8 GND 9 N/C 10 GND 11 N/C 12 SDA 10 5 15 13 HSYNC 14 VSYNC 15 SCL � JP18/JP19: LVDS Interface Connector PIN Description PIN Description 12 1 V 2 V LCD LCD 3 GND 4 GND 5 Y0-/Z0- 6 Y0+/Z0+ 7 Y1-/Z1- 8 Y1+/Z1+ 9 Y2-/Z2- 10 Y2+/Z2+ 13 14 11 CLK- 12 CLK+ 13 N/C 14 N/C 11 NOTE: LVDS cable should be produced very carefully. Y0- & Y0+ have to be fabricated in twister pair (Y1- & Y1+, Y2- & Y2+ and so on) otherwise the signal won’t be stable. Please set the proper voltage of your panel using JP25 before proceeding on installing it. NOTE: If use JP18 only, it just supports 16-bit single channel LVDS panel; If you want to use 36-bit dual channel LVDS panel, please use JP18 and JP19 combined. � JP25: Panel Voltage Select Options Settings 1 +5V Short 1-2 3 +3.3V (default) Short 2-3 � JP1: Inverter Power In Connector PIN Description 1 1 +12V 2 +12V 3 +5V 4 +5V 6 5 VDDEN 6 GND � J1: DVI Connector PIN Description PIN Description 1 TDC0# 2 +5V 3 TDC0 4 GND 5 GND 6 DETET 7 TDC1# 8 SC_DDC 9 TDC1 10 SD_DDC 11 GND 12 GND 13 TDC2# 14 TLC# 15 TDC2 16 TLC 17 GND 18 GND 19 N/C 20 N/C 2 20 1 19 12 3.8 PCI E-IDE Drive Connector CN11 is a standard 44-pin 2.0-pitch connector daisy-chain driver connector serves the PCI E-IDE drive provisions onboard the HS-1745. A maximum of two ATA/33/66/100 IDE drives can be connected to the HS-1745 via CN11. � CN11: IDE Connector PIN Description PIN Description 1 IDERST 2 GND 3 PDD7 4 PDD8 5 PDD6 6 PDD9 7 PDD5 8 PDD10 9 PDD4 10 PDD11 11 PDD3 12 PDD12 13 PDD2 14 PDD13 15 PDD1 16 PDD14 17 PDD0 18 PDD15 19 GND 20 N/C 21 PDDREQ 22 GND 23 IOW# 24 GND 25 IOR# 26 GND 27 PIORDY 28 470Ω with GND 29 PDDACK# 30 GND 31 IRQ14 32 N/C 33 PDA1 34 PD33/66 35 PDA0 36 PDA2 37 PDCS1# 38 PDCS3# 39 HDD Active 40 GND 41 VCC 42 VCC 43 GND 44 N/C 43 1 44 2 13 3.9 Serial ATA Connector You can connect the Serial ATA device that provides you high speeds transfer rates (150MB/sec.). If you wish to use RAID function, please note that these two serial ATA connectors just support RAID0 and only compatible with WIN XP. � CN7/CN9: Serial ATA Connector PIN Description 1 GND 2 SATATXP 17 3 SATATXN 4 GND 5 SATARXN 6 SATARXP 7 GND 14 3.10 Floppy Disk Drive Connector The HS-1745 uses a standard 34-pin header connector, CN12, for floppy disk drive connection. A total of two FDD drives may be connected to CN12 at any given time. � CN12: Floppy Connector PIN Description PIN Description 1 GND 2 DRVDEN0 3 GND 4 N/C 5 GND 6 DRVDEN1 7 GND 8 INDEX# 9 GND 10 MTR0# 11 GND 12 DS1# 13 GND 14 DS0# 15 GND 16 MTR1# 17 GND 18 DIR# 19 GND 20 STEP# 21 GND 22 WDATA# 23 GND 24 WGATE# 25 GND 26 TRAK00# 27 GND 28 WRTPRT# 29 GND 30 RDATA# 31 GND 32 HDSEL# 33 GND 34 DSKCHG# 2 34 1 33 15 3.11 Parallel Connector LTP1 is a standard 26-pin flat cable connector deigned to accommodate parallel port connection on the HS-1745. NOTE: If you want to use parallel port, 8-bit I/O function will be disabled. � LPT1: Parallel Connector PIN Description PIN Description 1 Strobe 14 Auto Form Feed 2 DATA 0 15 ERROR# 3 DATA 1 16 Initialize 1 14 4 DATA 2 17 Printer Select LN# 5 DATA 3 18 GND 6 DATA 4 19 GND 7 DATA 5 20 GND 8 DATA 6 21 GND 9 DATA 7 22 GND 10 Acknowledge 23 GND 13 26 11 Busy 24 GND 12 Paper Empty 25 GND 13 Printer Select 26 GND 3.12 Serial Port Connectors The HS-1745 offers NS16C550 compatible UARTs with Read/ Receive 16-byte FIFO serial ports and five internal 10-pin headers and two RS-422/485 connectors. � CN4A: COM 1 Connector (DB9) PIN Description PIN Description 1 DCD 2 DSR 5 9 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 6 1 9 GND 16 � JP12~JP16: COM 2~COM 6 Connector (5x2 Header) PIN Description PIN Description 1 DCD 2 DSR 9 1 3 RXD 4 RTS 5 TXD 6 CTS 10 2 7 DTR 8 RI 9 GND 10 +12V � J2/J3: RS-422/485 Connector (3x2 Header, COM 3/COM 4) PIN Description PIN Description 5 1 1 TX- 2 TX+ 3 RX+ 4 RX- 62 5 GND 6 +5V NOTE: The terminal resistance of RX & TX is set at 180Ω. � JP23/JP24: COM 3/COM 4 use RS-232 or RS-422/485 Select Options Settings 9 1 RS-232 (default) Open RS-485 by Auto (*1) Short 1-2, 3-4, 5-7, 8-10 10 2 RS-485 by –RTS (*-1) Short 1-2, 3-4, 7-9, 8-10 RS-422/485 Full Duplex (*2) Short 1-2, 3-4, 6-8 NOTE: *1: 2-wires RS-485 function *2: 4-wires point-to-point full duplex function 4-wires point-to-point full duplex RS-422/485 Typical RS-485 2-wires Mutildrop Network 17 3.13 Ethernet Connector The HS-1745 provides two external RJ-45 interface connectors. Please refer to the following for its pin information. � CN5A/CN6A: RJ-45 Connector PIN Description 1 TX+ 2 TX- 3 RX+ 4 R/C GND 1 8 5 R/C GND 6 RX- 7 R/C GND 8 R/C GND � JP9: Wake On LAN PIN Description 1 1 +5V 2 GND 3 3 Wake On LAN 3.14 USB Connector The HS-1745 provides two 8-pin connectors, at location JP10/JP11, for four USB ports, and four external USB2.0 ports at CN5B/CN6B. � CN5B/CN6B: External USB2.0 Connector PIN Description PIN Description 1 VCC 2 VCC 3 USBD0-/USB2- 4 USBD1-/USB3- 5 USBD0+/USB2+ 6 USBD1+/USB3+ 7 GND 8 GND � JP10/JP11: Internal USB2.0 Connector PIN Description PIN Description 1 2 1 VCC 2 VCC 3 USBD4-/USBD6- 4 USBD5-/ USBD7- 78 5 USBD4+/USBD6+ 6 USBD5+/ USBD7+ 7 GND 8 GND 18 3.15 CMOS Data Clear The HS-1745 has a Clear CMOS jumper on JP6. � JP6: Clear CMOS Options Settings 1 Normal Operation (default) Open 2 Clear CMOS Short IMPORTANT: Before you turn on the power of your system, please set JP6 to Open for normal operation. 3.16 Power and Fan Connectors HS-1745 provides one 20-pin ATX power in at ATX1. � ATX1: 20-pin ATX Power In Connector 11 1 PIN Description PIN Description 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON 5 GND 15 GND 6 +5V 16 GND 7 GND 17 GND 8 Power OK 18 -5V 9 5VSB 19 +5V 10 +12V 20 +5V 20 10 � JP3/JP4: Fan Power In Connector PIN Description 1 GND 13 2 +12V 3 Fan In 1/Fan In 2 Connector JP3/JP4 onboard HS-1745 is a 3-pin fan power output connector. And HS-1745 supports +12V Fan only. 19 3.17 Keyboard/Mouse Connectors The HS-1745 offers two possibilities for keyboard/mouse connections. The connections are via CN1 for an external PS/2 type keyboard/mouse or via JP2 for an internal 6-pin cable converter to a keyboard/mouse. � CN1: PS/2 6-pin Mini DIN Keyboard/Mouse Connector PIN Description 1 Keyboard Data 2 Mouse Data 6 5 3 GND 4 3 2 1 4 +5V 5 Keyboard Clock 6 Mouse Clock � JP2: 6-pin Keyboard/Mouse Connector PIN Description 1 Keyboard Data 1 2 Mouse Data 3 GND 4 +5V 6 5 Keyboard Clock 6 Mouse Clock 3.18 System Front Panel Control The HS-1745 has front panel control at location CN13 that indicates the power-on status. � CN13: System Front Panel Control PIN Description PIN Description 1 VCC 2 Speaker 3 HDD LED 4 N/C 5 PWR Button 6 GND 7 VCC 8 GND 9 Reset Switch 10 VCC 11 GND 12 PWR LED 20 Connector CN13 Orientation 1 2 HDD LED 3 4 Speaker 5 6 PWR Button 7 8 9 10 Reset PWR LED Button 11 12 3.19 IrDA Function JP27 is a 5-pin internal IR communication connector for connection of an IrDA device. � JP27: IrDA Connector PIN Description 1 1 VCC 2 N/C 3 IRRX 4 GND 5 5 IRTX 3.20 Watchdog Timer Once the Enable cycle is active a Refresh cycle is requested before the time-out period. This restarts counting of the WDT period. When the time counting goes over the period preset of WDT, it will assume that the program operation is abnormal. A system reset signal will restart when such error happens. The following sample programs show how to enable, disable and refresh the watchdog timer: ;---------------------------------------------------------------- ;Enter the WDT function mode, interruptible double-write ;---------------------------------------------------------------- MOV DX, 2EH MOV AL, 87H OUT DX, AL OUT DX, AL MOV DX, 2EH MOV AL, 07H OUT DX, AL MOV DX, 2FH 21 MOV AL, 08H OUT DX, AL MOV DX, 2EH MOV AL, F5H OUT DX, AL ;select CRF0 MOV DX, 2FH MOV AL, 80H OUT DX, AL MOV DX, 2EH MOV AL, F7H OUT DX, AL MOV DX, 2FH MOV AL, 00H OUT DX, AL MOV DX, 2EH MOV AL, F6H OUT DX, AL MOV DX, 2FH MOV AL, 00H ; *00H=Disabled OUT DX, AL ;---------------------------------------------------------------- ;Exit extended function mode ;---------------------------------------------------------------- MOV DX, 2EH MOV AL, AAH OUT DX, AL User can also use AL, 00H’s defined time for reset purposes, e.g.00H for Disable, 01H = 1sec, 02H=2sec….FFH=255sec. 3.21 TV-Out Function The HS-1745 can support TV-out function whose input could be up to 800 x 600 graphics resolutions. World Wide Video standards are supported including NTSC-M (North America, Taiwan), NTSC-J (Japan), PAL-b, D, G, H, I (Europe, Asia), PAL-M (Brazil), PAL-N (Uruguay, Paraguay) and PAL-NC (Argentina). � CN2: TV-Out Connector PIN Description PIN Description 5 3 1 GND 2 GND 6 7 3 DACB OUT 4 GND 1 4 5 DACC OUT 6 GND 2 7 GND 22 3.22 Audio Connectors The HS-1745 has an onboard AC97 3D audio controoler. The following tables list the pin assignments of the Line In/Audio Out connector. � CN3: SPDIF Connector PIN Description 2 1 GND 3 1 2 VCC 3 SPDIF � CN8: MIC In/Line Out Connector PIN Description PIN Description 1 AOUTL 2 AOUTR 1 2 3 GND 4 GND 78 5 MIC IN 6 N/C 7 GND 8 GND � CN10: External Audio Connector Blue Line In Green Line Out PINK MIC In 3.23 CompactFlash Connector The HS-1745 also offers a Type I/II CompactFlash connector which is IDE interface located at the solder side of the board. The designated CN14 connector, once soldered with an adapter, can hold CompactFlash cards of various sizes. Please turn off the power before inserting the CF card. � CN14: CompactFlash Connector PIN Description PIN Description 1 GND 2 IDE_PDD3 3 IDE_PDD4 4 IDE_PDD5 5 IDE_PDD6 6 IDE_PDD7 7 IDE_PDCS1# 8 GND …MORE ON NEXT PAGE… 23 PIN Description PIN Description 9 GND 10 GND 11 GND 12 GND 13 +3.3V 14 GND 15 GND 16 GND 17 GND 18 IDE_PDA2 19 IDE_PDA1 20 IDE_PDA0 21 IDE_PDD0 22 IDE_PDD1 23 IDE_PDD2 24 GND 25 GND 26 GND 27 IDE_PDD11 28 IDE_PDD12 29 IDE_PDD13 30 IDE_PDD14 31 IDE_PDD15 32 IDE_PDCS3# 33 GND 34 IDE_PDIOR# 35 IDE_PDIOW# 36 +3.3V 37 INT_IRQ15 38 +3.3V 39 +3.3V 40 N/C 41 RESET# 42 IDE_PDIORDY 43 CF_PDERQ 44 CF_REGB 45 IDE_ACTP# 46 DETECT 47 IDE_PDD8 48 IDE_PDD9 49 IDE_PDD10 50 GND Inserting a CompactFlash card into the adapter is not a difficult task. The socket and card are both keyed and there is only one direction for the card to be completely inserted. Refer to the diagram on the following page for the traditional way of inserting the card. � JP5: CF Use Master/Slave Select Options Setting 1 Master Short 2 Slave(default) Open NOTE: When use CF card, IDE device function will be disabled. 24 CompactFlash PCB Solder Side View CE TM CF Rear Side Made in Japan / Fabrique Au Japon 3.24 Expansion Slot The HS-1745 offers one Type III mini PCI slot at CN16, one x1 PCI-E slot at CON1, one standard PCI slot at PCI1. 3.25 8-bit I/O Function The HS-1745 offers one 8-bit input/output port by parallel port. NOTE: If you want to use 8-bit I/O, parallel port function will be disabled. � JP17: 8-bit Input/Output PIN Description PIN Description 1 VCC 2 GND 9 1 3 GD0 4 GD4 5 GD1 6 GD5 10 2 7 GD2 8 GD6 9 GD3 10 GD7 .286 .MODEL SMALL .DATA ;this is data area port equ 0378h ;print port can be change to 278h .CODE print macro buff mov dx, offset buff; mov ah,09h int 21h endm delay : push cx mov cx,0155h @@: jmp $+2 push cx mov cx,0ffffh wait1: loop wait1 pop cx loop @b pop cx ret begin proc near mov ax,@data mov ds,ax STI 25 Mov dx, port Mov al, 80h out dx, al ;;-------------------- ;;ROR mov cx, 08h @@: ror al, 1 call delay out dx, al loop @b pop cx ;;ROL push cx mov cx, 08h @@: rol al, 1 out dx, al call delay loop @b pop cx ;;-------------------- ;;-------------------- ;;ROR mov cx, 08h @@: ror al, 1 call delay out dx, al loop @b pop cx ;;ROL push cx mov cx, 08h @@: rol al, 1 out dx, al call delay loop @b pop cx ;;-------------------- ;;-------------------- ;;ROR mov cx, 08h @@: ror al, 1 call delay out dx, al loop @b pop cx ;;ROL push cx mov cx, 08h @@: rol al, 1 out dx, al call delay loop @b 26 pop cx ;;-------------------- ;;-------------------- ;;ROR mov cx, 08h @@: ror al, 1 call delay out dx, al loop @b pop cx ;;ROL push cx mov cx, 08h @@: rol al, 1 out dx, al call delay loop @b pop cx ;;-------------------- ;;-------------------- ;;ROR mov cx, 08h @@: ror al, 1 call delay out dx, al loop @b pop cx ;;ROL push cx mov cx, 08h @@: rol al, 1 out dx, al call delay loop @b pop cx ;;-------------------- ;;-------------------- ;;ROR mov cx, 08h @@: ror al, 1 call delay out dx, al loop @b pop cx ;;ROL push cx mov cx, 08h @@: rol al, 1 out dx, al call delay loop @b pop cx 27 ;;-------------------- ;;-------------------- ;;ROR mov cx, 08h @@: ror al, 1 call delay out dx, al loop @b pop cx ;;ROL push cx mov cx, 08h @@: rol al, 1 out dx, al call delay loop @b pop cx ;;-------------------- ;flash LED 3 time mov cx, 01h @@: mov al, 0ffh out dx, al call delay mov al,0h out dx, al call delay loop @b ee: mov ah, 4ch ;go back to dos int 21h .stack begin endp end begin 28 Chapter 4 AMI BIOS Setup The HS-1745 uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. 4.1 Starting Setup The AMI BIOS is immediately activated when you first power on the computer. The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system. While the BIOS is in control, the Setup program can be activated in one of two ways: 1. By pressing immediately after switching the system on, or 2. By pressing the key when the following message appears briefly at the bottom of the screen during the POST (Power On Self Test). Press DEL to enter SETUP. If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing , , and keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will be asked to... PRESS F1 TO CONTINUE, DEL TO ENTER SETUP 29 4.2 Using Setup In general, you use the arrow keys to highlight items, press to select, use the and keys to change entries, and press to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. ↑ Move to previous item ↓ Move to next item ← Move to previous item → Move to previous item Esc key Main Menu -- Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu PgUp key Decrease the numeric value or make changes PgDn key Increase the numeric value or make changes + key Increase the numeric value or make changes - key Decrease the numeric value or make changes F1 key Reserved F2 key Change color from total 8 colors. F2 to select color forward F3 key F2 to select color backward F4 key Reserved F5 key Reserved F6 key Reserved F7 key Reserved F8 key Reserved F9 key Reserved F10 key Save all the CMOS changes, only for Main Menu 30 4.3 Main Menu Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press to enter the sub-menu. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit System Overview AMIBIOS Version : 08.00.13 Build Date : 11/01/06 ID : HS174500 Processor Type : Intel® Core™ Duo CPU T2700 Speed : 2333MHz Count : 1 System Memory Size : 504MB � Select Screen �� Select Item System Time [00:29:32] ª - Change Field System Date [Tue 01/01/2002] Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. NOTE: A brief description of the highlighted choice appears at the bottom of the screen. 31 4.4 Advanced Settings This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced Settings WARNING: Setting wrong values in below sections may cause system to malfunction. � CPU Configuration � IDE Configuration � Floppy Configuration � Select Screen � SuperIO Configuration �� Select Item � Hardware Health Configuration ª - Change Field � ACPI Configuration Tab Select Field � APM Configuration F1 General Help � USB Configuration F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Configure advanced CPU settings Module Version –13.03 Manufacturer : Intel Brand String : Intel® Core™ Duo CPU T2700 Frequency : 2.33GHz FSB Speed : 667MHz Cache L1 : 64 KB Cache L2 : 2048 KB Max CPUID Value Limit [Disabled] Execute Disable Bit [Enabled] � Select Screen Core Multi-Processing [Enabled] �� Select Item CPU TM function [Enabled] ª - Change Field Venderpool Technology [Enabled] Tab Select Field Digital Thremal Sensor [Disabled] F1 General Help DTS Calibration [Enabled] F10 Save and Exit Intel® SpeedStep™ tech. [Automatic] ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 32 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit IDE Configuration ATA/IDE Configuration [Compatible] Legacy IDE Channels [SATA Pri, PATA Sec] � Primary IDE Master : [Not Detected] � Primary IDE Slave : [Not Detected] � Secondary IDE Master : [Not Detected] � Secondary IDE Slave : [Not Detected] Hard Disk Write Protect [Disabled] � Select Screen IDE Detect Time Out (Sec) [35] �� Select Item ATA(PI) 80Pin Cable Detection [Host] ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Floppy Configuration Floppy A [1.44 MB 3.5”] Floppy B [Disabled] � Select Screen �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 33 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Configure WIN627EHF Super IO Chipset OnBoard Floppy Controller [Enabled] Serial PortA Address [3F8] Serial PortA IRQ [3] Serial PortB Address [2F8] Serial PortB IRQ [4] Serial PortC Address [3E8] Serial PortC IRQ [10] Serial PortD Address [2E8] Serial PortD IRQ [11] � Select Screen �� Serial PortE Address [2F0] Select Item Serial PortE IRQ [10] ª - Change Field Serial PortF Address [2E0] Tab Select Field Serial PortF IRQ [11] F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Hardware Health Configuration Hardware Health Configuration System Temperature : CPU Temperature : Vcore : 3VCC : � Select Screen +12V : �� Select Item +1.5V : ª - Change Field +1.05V : Tab Select Field +5V : F1 General Help VBAT : F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 34 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit ACPI Settings ACPI Aware O/S [Yes] � General ACPI Configuration � Advanced ACPI Configuration � Select Screen �� � Chipset ACPI Configuration Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit General ACPI Configuration Suspend mode [S1 (POS)] � Select Screen �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced ACPI Configuration ACPI Version Features [ACPI v1.0] ACPI APIC support [Enabled] AMI 0EMB table [Enabled] Headless mode [Disabled] � Select Screen �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 35 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit USB Configuration Module Version – 2.24.0-11.4 USB Devices Enabled: None � Select Screen �� Legacy USB Support [Enabled] Select Item Hotplug USB FDD Support [Auto] ª - Change Field � USB Mass Storage Device Configuration Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit USB Mass Storage Device Configuration USB Mass Storage Reset Delay [20 Sec] Device #1 USB Hotplug FDD Emulation Type [Auto] � Select Screen �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 36 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Power Management/APM [Enabled] Video Power Down Mode [Disabled] Hard Disk Power Down Mode [Disabled] Suspend Time Out [Disabled] Throttle Slow Clock Ratio [50%] Keyboard & PS/2 Mouse [MONITOR] Power Button Mode [On/Off] Advanced Resume Events Controls Resume On Ring [Disabled] Resume On LAN [Disabled] Resume On PME# [Disabled] � Select Screen �� Resume On RTC Alarm [Disabled] Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Sorth Bridge ACPI Configuration Energy Lake Feature [Disabled] APCI ACPI SCI IRQ [Disabled] � Select Screen USB Device Wakeup From S3/S4 [Disabled] �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 37 4.5 Advanced PCI/PnP Settings This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction. Clean NVRAM [No] Plug & Play O/S [No] PCI Latency Timer [64] Allocate IRQ to PCI VGA [Yes] Palette Snooping [Disabled] PCI IDE BusMaster [Disabled] Offboard PCI/ISA IDE Card [Auto] IRQ3 [Available] IRQ4 [Available] IRQ5 [Available] IRQ7 [Available] IRQ9 [Available] IRQ10 [Available] IRQ11 [Available] IRQ14 [Available] IRQ15 [Available] DMA Channel 0 [Available] DMA Channel 1 [Available] � Select Screen �� DMA Channel 3 [Available] Select Item DMA Channel 5 [Available] ª - Change Field DMA Channel 6 [Available] Tab Select Field DMA Channel 7 [Available] F1 General Help F10 Save and Exit Reserved Memory Size [Disabled] ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 38 4.6 Boot Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Boot Settings Configuration Quick Boot [Enabled] Quiet Boot [Disabled] AddOn ROM Display Mode [Force BIOS] Bootup Nom-Lock [On] PS/2 Mouse Support [Auto] � Select Screen �� Wait For ‘F1’ If Error [Enabled] Select Item Hit ‘DEL’ Message Display [Enabled] ª - Change Field Interrupt 19 Capture [Disabled] Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Boot Device Priority 1st Boot Device [USB:USB Hotplug FD] � Select Screen �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Removable Drives 1st Drive [USB:USB Hotplug FD] � Select Screen �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 39 4.7 Security Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Security Settings Supervisor Password : Not Installed User Password : Not Installed � Select Screen Change Supervisor Password �� Select Item Change User Password ª - Change Field Boot Sector Virus Protection [Disabled] Tab Select Field F1 General Help Hard Disk Security F10 Save and Exit There are no supported Hard Disks. ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 4.8 Advanced Chipset Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced Chipset Settings WARNING: Setting wrong values in below sections may cause system to malfunction. � North Bridge Chipset Configuration � South Bridge Chipset Configuration � Select Screen �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 40 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit North Bridge Chipset Configuration DRAM Frequency [Auto] Configure DRAM Timing by SPD [Enabled] Memory Hole [Disabled] Boots Graphic Adapter Priority [PEG/PCI] Internal Graphics Mode Select [Enabled, 8MB] PEG Port Configuration PEG Port [Auto] PEG Force x1 [Disabled] � Select Screen Chipset Thermal Throttling [Disabled] �� Select Item DT in SPD [Disabled] ª - Change Field TS on DIMM [Disabled] Tab Select Field F1 General Help � Video Function Configuration F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Video Function Configuration DVMT Mode Select [DVMT Mode] DVMT/FIXED Memory [128MB] Boot Display Device [CRT] Flat Panel Type [800x600LVDS] Local Flat Panel Scaling [Auto] TV Connector [Auto] HDTV Output [Auto] TV Standard [VBIOS-Default] � Select Screen �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 41 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Sorth Bridge Chipset Configuration USB Function [8 USB Ports] USB 2.0 Controller [Enabled] Audio Controller [AC’97 Audio Only] PRO-NIC Controller [Disabled] SMBUS Controller [Enabled] Reserved Page Route [LPC] SLP_S4# Min. Assertion Width [1 to 2 seconds] Restore on AC Power Loss [Last State] PCIE Ports Configuration � Select Screen �� ONBOARD LAN 1 [Auto] Select Item ONBOARD LAN 2 [Auto] ª - Change Field PCIE SLOT 1 [Auto] Tab Select Field ASF Support [Enabled] F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 4.9 Exit Options BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Load Failsafe Defaults � Select Screen �� Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 42 Chapter 5 Software Utilities This chapter contains the detailed information of IDE, VGA, LAN and audio driver installation procedures. The utility disk that comes with the delivery package contains an auto-run program that invokes the installation programs for the IDE, VGA, LAN and audio drivers. The following sections describe the installation procedures of each driver based on WIN2K/XP operating systems. It is recommended that you install the drivers matching the sections listed in this chapter. 5.1 IDE Driver Installation 1. With the Utility CD Disk in you CD-ROM drive, open the File Manager and then select the CD-ROM drive. Open the Infinst folder and click Setup.exe to start proceed. 43 2. Once the Install Shield Wizard screen appears on the screen, make sure to close applications that are running and then click on Next> button. 3. The Welcome screen is now displayed, and then click on Next > button to continue. 44 4. The License Agreement dialog box then appears on the screen. Choose Yes to proceed. 5. When the Readme File Information dialog box pops up, just click on the Next > button to proceed. 45 6. Once the Install Shield Wizard finishes updating your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot. Only after your computer boots will the new settings take effect. 46 5.2 VGA Driver Installation 1. With the Utility CD Disk in you CD-ROM drive, open the File Manager and then select the CD-ROM drive. Open the VGA folder and click Setup.exe to start proceed. 2. Once the Setup Wizard appears on the screen and click on the Next > button. 47 3. Setup Wizard will extracting files to your hard drive, and then click on Next> to continue. 4. When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed. 48 5. The Intel® OEM Software License Agreement dialog box appears on the screen. Choose Yes to proceed. 6. After all installation finish, you will be prompted to start your system, click on the Finish button to reboot. 49 5.3 Audio Driver Installation 1. With the Utility CD Disk in you CD-ROM drive, open the File Manager and then select the CD-ROM drive. Open the Audio folder and click Setup.exe to start proceed. 2. Once the Install Shield Wizard screen appears on the screen, make sure to close applications that are running and then click on Next> button. 50 3. Realtek AC97 Audio Setup is preparing the Install Shield Wizard, which will guide you through the rest of the setup process. 4. Realtek AC97 Audio is configuring your new software installation. 51 5. Begin to install/update AC97 drivers. 6. After all installation finish, you will be prompted to start your system, click on the Finish button to reboot. 52 5.4 LAN Driver Installation 1. With the Utility CD Disk in your CD-ROM drive, right click on “My Computer” icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu. 2. Select on Ethernet Controller from the list of devices then double-click. The Ethernet Controller Properties screen then appears, select Reinstall Driver from the main menu to proceed. 53 3. Tick on the Install the software automatically (Recommended) once the following screen appears, click on the Next > to proceed. 4. The Hardware Update Wizard is copying files into your hard drive. 54 5. The Hardware Installation will pop up the screen below, click on Continue Anyway. 6. Hardware Update Wizard is installs the software, and then click on Next > to continue. 55 7. Once the Install Shield Wizard completes the operation and update of your USB2.0 driver. Click on the Finish button to complete the installation process. NOTE: Please repeat Step.1 ~ Step.7 to install LAN 2. 56