Manufacturers
BAILEY CONTROLS IPSYS 01
Description
Bailey Control's IPSYS-01 Module dimensions are 2.55 (5.60), 218.40 (8.60), 48.30
(1.90), and 444.50 (17.50). Operating enclosure (internal) temperature goes from
0° to 70°C (32° to 158°F), operating enclosure (external) temperature goes from
0° to 55°C (32° to 131°F), storage plus transport goes from (-40° to 85°C and
-40° to 185°F), and relative humidity operating temperature goes from 20% to 90%
up to 55°C (131°F) non-condensing.
Part Number
IPSYS 01
Price
Request Quote
Manufacturer
BAILEY CONTROLS
Lead Time
Request Quote
Category
COMPONENTS
Datasheet
Extracted Text
Modular Power System II Data Sheet Description The Modular Power System II supplies 5 VDC, 15 VDC, –15 VDC, 24 VDC, 48 VDC, and 125 VDC power to Harmony components of the Symphony Enterprise Management and Control System. The power system provides the operating voltages to Harmony I/O blocks, and Harmony rack I/O, controller, and communications modules as well as power to operate field devices. The power system accepts 120 VAC, 240 VAC, or 125 VDC input power. The Modular Power System II consists of the following components: Chassis: IPCHS01 Power Module Chassis (supports Harmony rack modules only). IPCHS02 Power Module Chassis (supports both Harmony blocks and rack modules). IPFCH01 Power Fan Chassis. Power entry: IPECB11 Power Entry Circuit Breaker (AC). IPECB13 Power Entry Circuit Breaker (DC). IPESW11 Power Entry Switch (AC). IPESW13 Power Entry Switch (DC). Modules: IPBLC01 Harmony Power (24 VDC). IPFLD01 Field Power (24 VDC). IPFLD24 Field Power (24 VDC). IPFLD48 Field Power (48 VDC). IPFLD125 Field Power (125 VDC). IPMON01 Power Monitor Module. IPSYS01 System Power (5 VDC, 15 VDC, –15 VDC, 24 VDC). System fan: IPFAN14Power System Fan (120/240 VAC, 125 VDC). Modular Power System II Power Module Usage by System Power Harmony Harmony Module Block I/O Rack I/O IPBLC01 • IPFLD01 IPFLD24 IPFLD48 IPFLD125 IPSYS01 Related Documents Number Document Title WBPEEUS210505?0 Harmony Modular Power System II, Overview Specifications Property Characteristic/Value General Power input Input Voltage Voltage External Ambient Temp. Nominal Operating Range 0° to 55°C (32° to 131°F) 120 VAC 102 to 132 VAC 240 VAC 204 to 264 VAC 125 VDC 102 to 144 VDC Current 20 A maximum per side Peak inrush current 15 A per power module for 100 msecs maximum for AC or DC input power Frequency 47 to 63 Hz Total harmonic distortion Less than 5% Efficiency 60% at full rated load Power factor Actively corrected to 0.95 minimum at input currents greater than 0.5 A Power module chassis IPCHS01, IPCHS02 Input power capacity 20 A maximum per side Output bus capacity 85 A at 5.1 VDC maximum 15 A at ±15.1 VDC maximum 85 A at 25.5 VDC maximum 12 A at 49.1 VDC maximum 12 A at 125.6 VDC maximum IPCHS02 Harmony power Approximately 7 A connector rating Power entry circuit breaker IPECB11, IPECB13 2 WBPEEUD210021B0 Modular Power System II Property Characteristic/Value Power entry switch IPEWS11, IPEWS13 Input voltage IPECB11, IPEWS11 102 to 264 VAC IPECB13, IPEWS13 102 to 144 VDC Input current 20 A maximum Voltage drop across 2 V drop at 20 A nominal breaker/ switch System fan IPFAN14 Input power 0.72 A nominal at 120 VAC 0.42 A nominal at 240 VAC 0.50 A at nominal 125 VDC Frequency 47 to 63 Hz Weight and dimensions 2 Weight Height Width Depth 1 Module kg (lb) mm (in.) mm (in.) mm (in.) IPBLC01 2.49 (5.46) 218.40 (8.60) 48.30 (1.90) 440.50 (17.50) IPBLK01 0.89 (1.95) 218.40 (8.60) 48.30 (1.90) 444.50 (17.50) IPFLD01 2.36 (5.20) 218.40 (8.60) 48.30 (1.90) 444.50 (17.50) IPFLD24 2.49 (5.46) 218.40 (8.60) 48.30 (1.90) 444.50 (17.50) IPFLD48 2.55 (5.62) 218.40 (8.60) 48.30 (1.90) 444.50 (17.50) IPFLD125 2.55 (5.62) 218.40 (8.60) 48.30 (1.90) 444.50 (17.50) IPMON01 0.71 (1.56) 218.40 (8.60) 35.56 (1.40) 401.32 (15.80) IPSYS01 2.55 (5.60) 218.40 (8.60) 48.30 (1.90) 444.50 (17.50) NOTES: 1. The total system weight is 48 kg (106 lb) maximum. 2. Dimension includes the handle. Weight Height Width Depth 1 Component kg (lb) mm (in.) mm (in.) mm (in.) IPCHS01/02 7.55 (16.60) 223.50 (8.80) 482.60 (19.00) 444.50 (17.50) IPECB11/13 2.55 (5.60) 114.30 (4.50) 193.04 (7.60) 162.56 (6.40) IPESW11/13 2.55 (5.60) 114.30 (4.50) 193.04 (7.60) 162.56 (6.40) IPFAN14 3.23 (7.10) 152.40 (6.00) 210.82 (8.30) 444.50 (17.50) IPFCH01 10.20 (22.40) 203.20 (8.00) 482.60 (19.00) 472.44 (18.60) NOTE: 1. The total system weight is 48 kg (106 lb) maximum. Electromagnetic/radio Meets IEC 801.3, level 3, 80 MHz to 1 GHz with no loss of function or false frequency interference status information for all units. NOTE: Do not use RFI sources producing 10 V/m or greater at 84.9 MHz within 2.2 m (7.2 ft) of the MPS II system. Fast transient/burst Meets IEC 801.4, level 3, mains 2 kV at 2.5 kHz, outputs 1 kV at 5.0 kHz with susceptibility no loss of function or false status information. Transient surge Meets IEC 801.5, level 3, 2 kV with no loss of function or false status information. WBPEEUD210021B0 3 Modular Power System II Property Characteristic/Value Electrostatic discharge Meets IEC 801.2, level 3 with no loss of function or false status information. Environmental Temperature Operating enclosure (internal) 0° to 70°C (32° to 158°F) Operating enclosure (external) 0° to 55°C (32° to 131°F) Storage and transport (-40° to 85°C (-40° to 185°F) Relative humidity Operating 20% to 90% up to 55°C (131°F) noncondensing 20% to 45% at 55° to 70°C (131° to 158°F) noncondensing Altitude Operating Sea level to 3,048 m (10,000 ft) Storage and transport Up to 9,144 m (30,000 ft) Air quality Noncorrosive per ISA S71.04 class LA, LB, LC severity level 1 Overvoltage category IEC 1010-1 Category III, for mains Category II, for mains to the IPCHS01 and IPCHS02 chassis Category I, for outputs Vibration 13.2 to 100 Hz, 0.7 Gs 2 to 13.2 Hz, 12 mm (0.47 in.) peak-to-peak displacement Certifications Canadian Standards Association Certified for use as process control equipment in an ordinary (nonhazardous) (CSA) location. Factory Mutual (FM) Approval for the following categories: Nonincendive for Class I Division 2, Groups A,B,C,D IPBLC01, IPFLD01, IPFLD24, IPFLD48, IPFLD125, IPSYS01 Power input Voltage 102 to 264 VAC; 102 to 144 VDC Current Full Load Input Current (A) Module 120 VAC 240 VAC 125 VDC IPBLC01 4.7 2.4 4.7 IPFLD01 2.2 1.0 2.2 IPFLD24 4.7 2.4 4.7 IPFLD48 4.4 2.2 4.4 IPFLD125 4.7 2.4 4.7 IPSYS01 4.3 2.0 4.3 Power output IPBLC01 Voltage/current Module 1 IPSYS01 IPFLD01 IPFLD48 IPFLD125 Outputs IPFLD24 Nominal VDC 5.09 15.10 -15.10 25.50 25.50 49.1 125.6 Minimum VDC 5.04 14.95 -14.95 24.35 24.35 48.5 124.2 Maximum VDC 5.25 15.75 -15.75 26.80 26.80 49.6 127.1 Maximum ripple 100 150 150 250 250 600 1,000 and noise (mV ) pp 2 Full load (A) 17.00 1.80 1.80 5.60 5.60/11.2 5.45 2.3 NOTES: 1. Total module power output cannot exceed 260 W. 2. 11.2 A for IPBLC01 and IPFLD24 modules. 4 WBPEEUD210021B0 Modular Power System II Property Characteristic/Value Load sharing Current shared equally between modules within 5% (highest current load to lowest current load) at full load Line regulation ±0.5% of the nominal output voltage over the input voltage range Load regulation Within specified minimum and maximum outputs from 0% to 100% load Hold up time 20 msecs following loss of power Heat dissipation 190 W (IPBLC01, IPFLD24, IPFLD48, IPFLD125) 95 W (IPFLD01) 175 W (IPSYS01) IPMON01 Power input 0.3 A at 120 VAC 0.2 A at 240 VAC and 125 VDC System bus voltage monitor trip Low Trip High Trip Voltage Bus points Nominal (VDC) Min Max Min Max 1 1 5 4.75 4.80 NA NA 1 1 15 14.50 14.70 NA NA 1 1 -15 -14.50 -14.70 NA NA 1 1 25.5 24.20 24.50 NA NA 25.5 (aux) 21.40 21.60 27.00 27.40 49.1 (aux) 42.50 43.35 54.00 54.60 125.6 (aux) 113.05 115.05 142.75 144.75 NOTE: 1. Power module provides overvoltage protection. Input voltage monitor trip points 1 Low Trip Input Voltage (Nominal) Min Max 120 VAC 88 90 240 VAC 176 180 125 VDC 88 90 NOTE: 1. The MPS II system will operate at voltages as low as the input voltage monitor low trip point, however operation below the minimum system input voltage specification is not recommended. Logic status inputs 2 inputs, logic 0 = fault Logic 0 ��0.8�VDC at 10 mA sink current Logic 1 ��3.1VDC at 80 µA source current Fan status inputs 2 inputs for fan speed monitoring of low fan speed (fan speed controlled as a function on internal cabinet temperature) Power fail interrupt (PFI) 1 output, open collector driven (nonisolated), logic 0 = power failure Logic 0 � 0.8�VDC at 10 mA sink current Logic 1 ��4.75 to 5.25 VDC at 80 µA source current Status out 1 output, open collector driven (nonisolated), logic 0 = fault Logic 0 ��0.8�VDC at 10 mA sink current Logic 1 ��4.75 to 5.25 VDC at 80 µA source current Bus alarm 1 output, opto-isolated open collector driven (24 V), logic 1 = fault Logic 0 ��1.2 VDC at 150 mA sink current Logic 1 ��5 to 30 VDC at 80 µA source current WBPEEUD210021B0 5 Modular Power System II Property Characteristic/Value Power alarm 1 output, opto-isolated open collector driven (24 V), logic 1 = fault Logic 0 ��1.2�VDC at 150 mA sink current Logic 1 ��5 to 30 VDC at 80 µA source current I/O alarm 1 output, opto-isolated open collector driven (24 V), logic 1 = fault Logic 0 ��1.2�VDC at 150 mA sink current Logic 1 ��5 to 30 VDC at 80 µA source current SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Nomenclature 12 34 56 78 Chassis I P C H S 0 1 _ Power module chassis (supports Harmony rack modules only) I P C H S 0 2 _ Power module chassis (supports both Harmony blocks and rack modules) I P F C H 0 1 _ Power fan chassis Fans I P F A N 1 4 _ 120/240 VAC, 125 VDC Modules I P B L C 0 1 _ Harmony power (24 VDC) I P F L D 0 1 _ Field power (24 VDC) I P F L D 2 4 _ Field power (24 VDC) I P F L D 4 8 _ Field power (48 VDC) I P F L D 1 2 5 Field power (125 VDC) IP M O N 0 1 _ Power monitor I P S Y S 0 1 _ System power (5 VDC, 15 VDC, –15 VDC, 24 VDC) Power Entry I P E C B 1 1 _ Circuit breaker (AC) I P E C B 1 3 _ Circuit breaker (DC) IP E S W 1 1 _ Switch (AC) I P E S W 1 3 _ Switch (DC) 6 WBPEEUD210021B0 Modular Power System II WBPEEUD210021B0 7 Modular Power System II For the latest information on ABB visit us on the World Wide Web at http://www.abb.com Our worldwide staff of professionals is ready to meet your needs for process automation. For the location nearest you, please contact the appropriate regional office. Americas Asia/Pacific Germany Europe, Africa, Middle East 29801 Euclid Avenue 539 Yishun Industrial Park A Industriestrasse 28 Via Puccini 2 Wickliffe, Ohio USA 44092 Singapore 768740 D-65760 Eschborn 16154 Genoa, Italy Telephone 1-440-585-8500 Telephone 65-756-7655 Germany Telephone 39-010-6584-943 Telefax 1-440-585-8756 Telefax 65-756-7309 Telephone 49-6196-800-0 Telefax 39-010-6584-941 Telefax 49-6196-800-1119 Form WBPEEUD210021B0 Litho in U.S.A. Oct2000 Copyright © 2000 by ABB Automation Inc., as an Unpublished Work, All Rights Reserved ® Registered Trademark of ABB Automation Inc. ™ Trademark of ABB Automation Inc.
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the IPSYS 01 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods