Embedded Power for Business-Critical Continuity Rev. 3.4.09_133 HPS35 Series 1 of 4 HPS35 Series 350 - 1400 Watts Total Power: 350 Watts per module Input Voltage: 90-264 VAC # of Outputs: Single and Electrical Specifications standby Input Input voltage: 90-264 VAC typical Frequency: 47-440 Hz Inrush current: 40 A peak typical @ 25 °C Efficiency: 80% typ @ full load, 230 VAC Power factor: 0.98 typical @ 115 VAC, full load Special Features Turn-on time: AC ON -2 sec., Inhibit / Enable 160 ms • Active Power Factor Correction EMI filter standard: CISPR 22, EN55022 Level “B” • EN61000-3-2 compliant Leakage current standard: <0.5 mA max @ 230 VAC @ 60Hz (per module) • CISPR22, EN55022 Level-B conducted/radiated EMI Radiated EMI: CISPR 22, EN55022 Level “B” • EN61000 immunity standards Holdup time: 20 ms minimum (independent of input VAC) • 5V @2A sb AC OK: 5 ms early warning minimum before outputs lose regulation • Overvoltage protection (OVP) Harmonic distortion: Meets EN61000-3-2 • Overcurrent protection (OCP) Isolation: Meets EN60950 • Overtemperature protection (OTP) Output • AC OK signal and indicator LED Adjustability: ±5% of nominal output voltage • DC OK signal and indicator LED Overall regulation: ±3% • Remote Inhibit • Remote Sense on main output Ripple: 1% of Vout pk - pk (20 MHz bandwidth) • Hot Plug Dynamic response: 4% from 25% to 75% load step • N+1 Redundant Recovery time: To within 1% in <300 µsec • 2 year warranty Overcurrent protection: 115 - 130% of rated output current Short circuit protection: Protected for continuous short circuit. Auto recovery. Overvoltage protection: 120 - 140% AC Reset. Reverse voltage protection:100% of rated output voltage Thermal protection: Main and Aux disabled when internal temp exceeds safe operating range Remote sense: Up to 0.5 V total drop Safety Single wire parallel: Current share to within 10% of total rated current on • UL UL60950-1, 1st Ed. main output (April 1, 2003) DC OK: ±5% of nominal • CSA CSA C22.2 60950-1-03 • TUV EN60950-1:2001 (1st Ed.) • CB IEC60950-1, 1st Ed. (2001) • CE Mark (LVD) Rev.3.4.09_133 HPS35 Series Module Information  of 4 Environmental Specifications Operating temperature: 0 ° to 50 °C ambient. Derate each output 2.5% per degree from 50 ° to 70 °C Shock: Operating: 4g, half sine, 22 ms minimum duration, all 6 faces Non-operating: 30g, half since, 6 ms minimum duration, all 6 faces Random Vibration: Operating: 1g rms, 20 min/axis Non-operating: 2.5g rms, 20 min/axis Humidity: 95% non-condensing Storage Temperature: -40 ° to +85 °C Temperature coefficient:0.04% per °C Cooling Internal DC fans Ordering Information Modules HPS35L-NNR-000 12V Watts 350 Input Voltage 90-264 HPS35Q-NNR-000 24V Module ID HPS35 HPS35W-NNR-000 48V Code Volt Output Amps L 12.0 29.2 Q 24.0 14.6 W 48.0 7.3 Max. Size (H x W x L) 1.6” x 4.3” x 10.5” Number per Rack 4 Unit Weight (lbs) 3.2 (All units in mm) Pin Assignments HPS35 Module TOP SIDE 1-24 Bottom Unit Connector Top 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Card Edge Connector with gold fingers double-sided 1.6mm FR-4 PCB Pin Description Pin Description Pin Description Pin Description PIN DESIGNATION A B C D E F H J K L M N P R S T U V W X Y Z AA AB TOP BOTTOM A AC (L) P COMMON 1 AC (L) 13 COMMON PIN NO. SIGNAL NAME PIN NO. SIGNAL NAME B BLANK R V OUT 2 BLANK 14 V OUT 1 AC (L) A AC (L) TOP BOTTOM 2 BLANK B BLANK 3 AC (N) 15 V OUT PIN NO. SIGNAL NAME C APIN NO C (N) . SIGNAL NAME S V OUT 3 AC (N) C AC (N) 14 +12V R +12V Mating connector: D BLANK T V OUT 4 BLANK 16 V OUT 4 BLANK D BLANK 15 +12V S +12V 5 GND E GND 16 +12V E GND T +12V U V OUT EDAC 307-048-520-201 or 5 GND 17 V OUT 6 SWP F -SENSE 17 +12V U +12V F -SENSE V V OUT 6 SWP 18 V OUT equivalent 7 5V RTN H +SENSE 18 +12V V +12V 8 7 COMMON5V RTNJ 19 COMMONV OUT H +SENSE W V OUT 19 +12V W +12V 9 COMMON K COMMON 20 BLANK X INHIBIT 8 COMMON 20 BLANK J COMMON X INHIBIT Rating: 5A per contact 10 COMMON L COMMON 21 +5V STANDBY Y TBD K COMMON Y TBA 11 9 COMMONCOMMO MN 21 COMMON+5 STANDBY 22 TBD Z AC OK 12 COMMON N COMMON 23 FAN MON AA DC OK L COMMON Z AC OK 10 COMMON 22 TBA 13 COMMON P COMMON 24 I2C CLK AB I2C DATA 11 COMMON 23 FAN MON M COMMON AA DC OK 2 2 N COMMON AB IC DATA 12 COMMON 24 IC CLK 7.6 53.8 HPS35L-NNR-000 MAXIMUM OUTPUT POWER IS 350W INPUT: OUTPUT: 90 - 240VAC - 40A +12V / 29A 50/60 Hz DATE: YYWW REV: XX S/N: MMMMWWSSSSRRC A/C CODE: XXXX MADE IN PHILIPPINES 73-811-029 SERIAL NO.: Rev. 3.4.09_133 HPS35 Series 3 of 4 Rack Information Racks HPR1-00 Watts 1400 (fully populated) 482.6 Input Voltage 90-264 22.0 Module ID HPS35 Rack ID HPR1-00 Max. Size (H x W x L) 1.75” x 19.0” x 13.0” Module Distribution(4 ea) HPS35 Standard Size 1U Unit Weight (lbs) 8.6 + RTN 468.8 343.2 442.0 330.2 + RTN 3.2 AC Cord: (North America) 1 19 For all other countries, please contact factory. 20 37 1) Quail Electronics Series 5050 or equivalent (15A/125V) PIN DESIGNATION Supply End - NEMA 5-15P SLOT 1 SLOT 2 SLOT 3 SLOT 4 Equipment End - IEC 60320-C19 1: 5V RTN (std-by) 6: INHIBIT 13: INHIBIT 24: INHIBIT 31: INHIBIT 2: (+) sense 7: DC OK 14: DC OK 25: DC OK 32: DC OK 3: (-) sense 8: AC OK 15: AC OK 26: AC OK 33: AC OK 2) Quail Electronics Series 5052 or equivalent (20A/125V) 4: 5V (std-by) 9: I2C Address #1 16: I2C Address 27: I2C Address 34: I2C Address Supply End - NEMA 5-20P 5: not used 10: I2C Address #2 17: I2C Address 28: I2C Address 35: I2C Address 20: I2C CLK 11: Fan Monitor 18: Fan Monitor 29: Fan Monitor 36: Fan Monitor Equipment End - IEC60320-C19 21: I2C DATA 12: Global AC OK 19: Global INHIBIT 30: Not used 37: Not used 22: SWP Blank Panel: 23: Not used Astec P/N 73-686-000 D-sub Connector Pin Outs Pin Description Pin Description PSU Connector 1 5V Return (std-by) 20 I2C CLOCK 617-A-037-P-AJ-1-21 (Male socket) Amphenol 2 + Remote Sense 21 I2C DATA 3 - Remote Sense 22 SWP 4 5V Stand by 23 Unused (I2C_INT) 5 Unused 24 Module Inhibit S Pin Out Diagram D-sub Connector (male) 25 DC OK 6 Module Inhibit L S 26 AC OK 7 DC OK O L 27 I2C_ADD#1 8 AC OK T O 28 I2C_ADD#2 9 I2C_ADD#1 3 T Mating Connector 29 Fan Monitor 10 I2C_ADD#2 1 617-A-037-S-AJ-1-20 (Female socket) Amphenol 11 Fan Monitor 30 Unused 12 Global AC OK 31 Module Inhibit S 13 Module Inhibit 32 DC OK L S 14 DC OK 33 AC OK O L 15 AC OK 34 I2C_ADD#1 T O Pin Out Diagram D-sub Connector (female) 16 I2C_ADD#1 4 35 I2C_ADD#2 T 2 17 I2C_ADD#2 36 Fan Monitor 18 Fan Monitor 37 Unused 19 Global Inhibit 6.0 31.7 13.4 25.0 43.7 HPR1-00 MAXIMUM OUTPUT POWER IS 1400W INPUT: OUTPUT: 90 - 240VAC - 40A +12V / 29A 50/60 Hz DATE: YYWW REV: XX S/N: MMMMWWSSSSRRC A/C CODE: XXXX MADE IN PHILIPPINES 73-810-002 SERIAL NO.: Embedded Power for Business-Critical Continuity Rev.3.4.09_133 HPS35 Series D. Sub Connector Additional Notes 4 of 4 Americas Pin 2 + Remote Sense DC OK (OUT Signal) 5810 Van Allen Way Pin 3 - Remote Sense Carlsbad, CA 92008 Compensates for up to 0.5V drop. USA Recommended shielded twisted wire pair. Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Pin 12 - Global AC OK (OUT signal) Europe (UK) Note: DC OK signals for each slot in the rack is accessible in the D-sub Waterfront Business Park connector (J18). Refer to Connector Merry Hill, Dudley Pin-out table for pin assignments. Pin 1 West Midlands, DY5 1LX is the Return Pin. United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Note: AC OK signals are OR’ed together AC OK (OUT Signal) internally. If any module fails, the LED on the affected module will be off and Asia (HK) the logic signal will indicate AC NOT OK. 14/F, Lu Plaza 2 Wing Yip Street Pin 19 - Global Inhibit (IN signal) Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Note: AC OK signals for each slot in the Facsimile: +852 2176 3888 rack is accessible in the D-sub connector (J18). Refer to Connector For global contact, visit: Pin-out table for pin assignments. Pin 1 Note: All outputs disabled when Pin 19 is the Return Pin. www.PowerConversion.com is open or High. techsupport.embeddedpower Hi state: Source 100uA @ 4V @emerson.com Pin 22 - SWP (IN/OUT signal) Low State: Sink 10mA @ 0.5V SWP Pin is used when PIN 22 While every precaution has been taken to ensure connecting racks in Fan Monitor (OUT Signal) accuracy and completeness in this literature, Emerson parallel to achieve Network Power assumes no responsibility, and disclaims current sharing. Current all liability for damages resulting from use of this PIN 3 share accuracy is information or for any errors or omissions. typically 10% of full load. Emerson Network Power. Note: SWP Voltage is 5V at 100% load The global leader in enabling current. business-critical continuity. Module Inhibit (IN Signal) Note: Fan Monitor signals for each slot in the rack is accessible in the D-sub AC Power connector (J18). Refer to Connector Connectivity Pin-out table for pin assignments. Pin 1 is the Return Pin. DC Power Embedded Computing I2C_ADD#1 Note: Module Inhibit signals for each I2C_ADD#2 Embedded Power slot in the rack is accessible in the D-sub TBD Monitoring connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 Outside Plant is the Return Pin. Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co.