Manufacturers
ASTEC DS1300
Description
Astec DS1300 11.4 V to 13.2 V AC-DC Power Supply
Part Number
DS1300
Price
Request Quote
Manufacturer
ASTEC
Lead Time
Request Quote
Category
AC-DC POWER SUPPLIES » DISTRIBUTED POWER FRONT-END
Specifications
Efficiency
>80% typical at full load, high line
Frequency
47-63 Hz, single phase AC
Hold up time
12ms minimum
Input range
90-264 VAC, 910w, 180 - 264 vac, 1300w
Inrush current
35A maximum inrush current
Leakage current
0.75mA @ 240VAC
Main DC voltage
+12v @ 74A (90VAC) or 106A (180VAC)
Operating Temperature
-10 to 50C
Over current
+12vdc; 110 - 130%
Power factor
0.99 typical
Regulation
+12vdc; ±3%; +3.3vsb; ±3%
Stand-By
+3.3vsb @ 7A
Features
- (60mm x 38mm)
- +12vdc Output
- +3.3vdc Stand-By
- 13W/ in3
- 2U X 3U Form Factor 7.5” long
- AC shutdown
- Active AC Inrush Control
- Active Current Sharing
- Active Power Factor Correction
- Amber LED Status, Power Failed
- EERPOM for FRU Data
- EN61000-3-2 Harmonic Compliance
- Fan Fail Output Signal
- Green LED Status, Power OK
- Hot Plug Operation
- I2C Communication Interface Bus
- INTEL, SSI Std. FRU Data Format
- INTEL, SSI Std. Logic Timing
- Internal Cooling Fans
- Internal Fan Speed Control
- Internal OR’ing Main and Stand-by
- N + 1 Redundant
Datasheet
Extracted Text
Embedded Power for Business-Critical Continuity Rev.03.15.11_17 DS1300-3 1 of 4 DS1300-3 1300 Watts 12V Distributed Power System Distributed Power Bulk Front-End Total Output Power: 1300 Watts +12vdc Main Output; +3.3vdc Stand-by Output Wide Range Input voltage: 90 - 264VAC 180 - 264vac 1300w 90 - 264vac 910W Electrical Specifications Input Special Features 90-264 VAC, 910w Input ra nge 180 - 264 vac, 1300w • Active Power Factor Correction Frequency 47-63 Hz, single phase AC • EN61000-3-2 Harmonic Inrush current 35A maximum inrush current Compliance • Active AC Inrush Control Efficiency >80% typical at full load, high line • 2U X 3U Form Factor 7.5” long Conducted EMI FCC Subpart J EN55022 Class A 3 • 13W/ in Radiated EMI FCC Subpart J EN55022 Class A • +12vdc Output • +3.3vdc Stand-By Power factor 0.99 typical • Hot Plug Operation Leakage current 0.75mA @ 240VAC • N + 1 Redundant Hold up time 12ms minimum • Internal OR’ing Main and Stand- by Output • Active Current Sharing Main DC voltage +12v @ 74A (90VAC) or 106A (180VAC) • Internal Cooling Fans Stand-By +3.3vsb @ 7A (60mm x 38mm) 2 • IC Communication Interface Bus Adjustment range Factory Set, no pot adjustments • EERPOM for FRU Data Regulation +12vdc; ±3%; +3.3vsb; ±3% • Green LED Status, Power OK +12vdc; 110 - 130% Over current • Amber LED Status, Power Failed latches off if overcurrent lasts over 1.5 seconds, • Internal Fan Speed Control otherwise it is auto recovery. • Fan Fail Output Signal +3.3vsb, 7A - 105% - 130% • INTEL, SSI Std. Logic Timing Over voltage +12vdc; 13.7v ±7% • INTEL, SSI Std. FRU Data Format +3.3vsb; 4.0v ±7% • AC shutdown <85VAC or 170VAC Under voltage +12vdc; 11.0 - 11.4vdc • One Year Warranty Turn-on delay <3 Second max +12vOutput Rise Time 5 - <200mS, Monotonic Rise Safety I Share 12V 15% from 50 - 100% load UL/cUL 60950 (UL Recognized) 1st edition (UL)60950-1-03 CSA NEMKO+ CB Report EN60950 EN60950 CE Mark China CCC CB Test Report Embedded Power for Business-Critical Continuity Rev.03.15.11_17 DS1300-3 Logic Control 2 of 4 An active low signal that turns on the 12vdc power rail. When this signal PS_ON High, or left open, the 12vdc output turn off. The 3.3Vsb output remains on. POK Is a power good signal to be pulled low by the power supply to indicate that all the outputs are within regulation limits of the power supply. (turn-on delay 100 - 500mS) In the event of a power supply failure (OVP at any output, UV at any output, PS FAIL OTP or other electrical failure), this signal shall go to a High state. High when AC is not OK, Low if AC is OK AC OK PRESENT Low i f PSU is Present, High if not Present; Pull high in system. FAN FAIL Low if one or both fans have failed PS_KILL This pin shall quickly turn off the power supply and prevent arching of the DC output contacts. Environmental Specifications Operating temperature: -10° to 50°C ; 50% power derating at 70°C Storage temperature: -40°C to +85°C Altitude, operating 10,000ft. Electromagnetic EN61000-3-2, -3-3 susceptibility / Input transients: EN61000-4-2, 4.3, 4-4, -4-5, 4-11 Level EN55024:1998 RoHS, RS5 Humidity: 5 to 95% RH, non-condensing Shock and vibration specificatons complies with Astec Std. Specifications, Q3205 MTBF (Demonstrated) 500K Hrs at full load, 50°C Anti-smoke Emission Due to internal overload or internal failures Fan life: 70,000 hrs @ 40°C Ordering Information Nominal Output Set Point Total Minimum Maximum Output Ripple Output Voltage Set Point Tolerance Regulation Current Current P/P Main (>90VAC) 12.00vdc ±0.2% ±3% 0A 74A 120mV Main (180VAC) 12.00vdc ±0.2% ±3% 1.0A 106A 120mV Std-By 3.3vdc ±1% ±3% 0.5A 7.0A 50mV Embedded Power for Business-Critical Continuity Rev.03.15.11_17 DS1300-3 3 of 4 AIRFLOW DIRECTION 190.5 7.5" (162.9) 19.3 65.5 2.58" AC CABLE RETAINER BLACK 3D VIEW HF GREEN EMI CLIP LAIRD 771062031 165.6 (2X) EMI CLIP 6.52" LAIRD 77-020 7.2 MODEL LABEL 0.283" 71.1 2.80" 143.3 5.65" (4X) EMI CLIP LAIRD 77-020 124.45 STATUS 4.90" LED INDICATORS AC INLET 15A C14 TYCO P/N 1-1450330-8 OR FCI P/N 51 939-055 Power Supply LED’s NOTE: Dimensions given in mm and inches. Power Supply Condition PWR FAIL (green) (amber) No AC power to all PSU Off Off No AC power to this PSU only (includes No OFF On output, over voltage, over temperature) AC present / Standby Output On Blinking Off Power supply DC outputs ON and OK ON Off Power supply failure (over current) OFF Blinking Embedded Power for Business-Critical Continuity Rev.03.15.11_17 DS1300-3 Americas 4 of 4 DC Output Connector Pinout Assignment 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Europe (UK) Waterfront Business Park Merry Hill, Dudley Male connector as viewed from the rear of the supply West Midlands, DY5 1LX United Kingdom Pin Signal Name P1 - Unit Telephone: +44 (0) 1384 842 211 PB P1 +12V Facsimile: +44 (0) 1384 843 355 FCI Power blade FCI p/n PB P2 +12V RETURN (Pre-mate) PB P3 +12V 51939-055 PB P4 +12V RETURN (Pre-mate) Asia (HK) PB P5 +12V 14/F, Lu Plaza PB P6 +12V RETURN (Pre-mate) 2 Wing Yip Street P1 - Mate PB P7 +12V Kwun Tong, Kowloon PB P8 +12V RETURN (Pre-mate) Hong Kong Mating Connector A1 +3V3 STAND-BY Telephone: +852 2176 3333 (System side) A2 +3V3SB RETURN Facsimile: +852 2176 3888 FCI Power blade A3 PS_PRESENT ( Power Supply Seated) - (short pin) Part number 51915-023 A4 POK (Output Power Ok) For global contact, visit: A5 PS FAIL (Failure Signal) www.Emerson.com/EmbeddedPower A6 SPARE techsupport.embeddedpower A7 SPARE @emerson.com B1 +3V3 STAND-BY AC Input Connector B2 +3V3SB RETURN EN60320 Type C14 While every precaution has been taken to ensure B3 PSON (Power Enable Signal) accuracy and completeness in this literature, Emerson B4 PSKILL (Power Supply Fast Shutdown) - (short pin) Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this B5 SDA (I2C Data Signal information or for any errors or omissions. B6 A2 (I2C Address BIT 2 Signal) B7 FAN FAIL (Fan Fail Signal) Emerson Network Power. C1 +3V3 STAND-BY The global leader in enabling C2 +3V3SB RETURN C3 AC OK (AC Input Present) business-critical continuity. C4 +12V RMT SENSE C5 +12V RMT SENSE RETURN AC Power C6 A1 (I2C Address BIT 1 Signal) Connectivity C7 +3V3 STAND-BY RMT SENSE Return (-) D1 +3V3 STAND-BY DC Power D2 +3V3SB RETURN Embedded Computing D3 12IS (+12V Current Share) D4 SPARE Embedded Power D5 SCL (I2C Clock Signal)* Monitoring D6 A0 (I2C Address BIT 0 Signal) D7 +3V3 STAND-BY RMT SENSE (+) Outside Plant 2 Power Switching & Controls *Supports I C standard mode (100 kHz) only Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2011 Emerson Electric Co.
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the DS1300 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
Astec DS1200-3-002 12.0 V AC-DC Power Supply
Astec DS1800/2000 12.0 V AC-DC Power Supply
Request a Quote
The quote request has been received
Close
Facing challenges or have inquiries? Feel free to contact us!
Call Us +1-469-283-2440
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods