Total p power: 350W 350-1400 Watts Input v voltage: 90-2 264VAC # o of o outputs: One & & s standby HPS35 Series Electrical Specs Input Input voltage 90-264 VAC typical Frequency 47-440 Hz Inrush current 40 A peak typical @ 25°C Efficiency 80% typ @ full load, 230 VAC Power factor 0.98 typical @ 115 VAC, full load Turn-on time AC - ON 2 sec. Inhibit / Enable 160 ms Special Features EMI filter standard CISPR 22 EN55022 Level “B” Leakage current standard <0.5 mA max @ 230 VAC @ 60Hz • Active Power Factor Correction (per module) • EN61000-3-2 compliant Radiated EMI CISPR 22 EN55022 Level “B” • CISPR22, EN55022 Class-B conducted/radiated EMI Holdup time 20 ms minimum • EN61000 immunity standards (independent of input VAC) •5V @2A SB AC OK 5 ms early warning minimum before • Overvoltage protection (OVP) outputs lose regulation • Overcurrent protection (OCP) Harmonic distortion Meets EN61000-3-2 • Overtemperature protection (OTP) Isolation Meets EN60950 • AC OK signal and indicator LED • DC OK signal and indicator LED Output • Remote inhibit Adjustability ±5% of nominal output voltage • Remote Sense on main output •Hot Plug Overall reg <3% • N+1 Redundant Ripple 1% of Vout Pk - Pk 2 • Optional I C board (pending) (20 MHz bandwidth) Voltage Monitoring Dynamic response 4% with 50% load step Current Monitoring Recovery time To within 1% in <300 µsec Remote on/off Overcurrent protection 115%-130% of rated output current DC OK / AC OK Short circuit protection Protected for continuous short circuit. Temperature Auto recovery. Fan fail Overvoltage protection 120 - 140% . AC Reset. Reverse voltage protection 100% of rated output current Thermal protection Main and Aux disabled when internal temp exceeds safe operating range. Environmental Remote sense Up to 0.5 V total drop Single wire parallel Current share to within 10% of total rated current on main output Operating temperature: 0°C to +50°C ambient, derate output @ 2.5% per degree from 50°C to 70°C DC OK ±5% of nominal Shock: Operating - 4g, half since, 22 ms minimum Minimum load* None required (as a standalone module) duration, all 6 faces Standby voltage 5 VDC @2A max. present whenever AC input is applied Non-operating: 30g, half since, 6 ms minimum Global Inhibit Logic “0” duration, all 6 faces Random Vibration *3A minimum required for current share operation Operating: 1g rms, 20 min/axis Non-operating: 12.5g rms, 20min/axis Safety Humidity: 95% non-condensing Storage temperature: -40°C to +85°C UL UL60950-1, 1st Ed. (April 1, 2003) Temperature coefficient: 0.04% per °C CSA CSA C22.2 60950-1-03 TUV EN60950-1:2001 (1st Ed.) Cooling: Internal DC fans CB IEC60950-1, 1st Ed. (2001) CE Mark (LVD) Technical Support: (888) 41-ASTEC or (407) 241-2752 rev 02.24.05 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-96622 HPS35 ASIA E EU UR RO OP PE E A AM ME ER RI IC CA AS S Units 2111-2116, Level 21 Astec House, Waterfront Business Park 5810 Van Allen Way Tower1, Metroplaza Merry Hill, Dudley Carlsbad, CA 92008 223, Hing Fong Road West Midlands, DY5 1LX, UK Telephone: 760-930-4600 Fwai Fong, New Territories Telephone: 44 (1384) 842-211 Facsimile: 760-930-0698 Hong Kong Facsimile: 44 (1384) 843-355 Telephone: 852-2437-9662 Facsimile: 852-2402-4426 Modules Module Max. Size Max. Module Number Unit Code (H x W x L) Power per Rack Weight (lbs) HPS35 1.6" x 4.3" x 10.5" 350 W 4 3.2 Watts 350 Input Voltage 90-264 Power Special Options Module ID HPS35 & Modifications 35 = 350 W Contact Astec 50 = 500 W Code Volts Output Amps L 12.0 29.2 N N N R 0 0 0 XXX HPS W 48.0 7.3 Output Voltage L = 12 V W = 48 V H HP PS S3 35 5L L-N NN NR R-0 00 00 0 www.astecpower.com 7.6 53.8 HPS35L-NNR-000 MAXIMUM OUTPUT POWER IS 350W INPUT: OUTPUT: 90 - 240VAC - 40A +12V / 29A 50/60 Hz DATE: YYWW REV: XX S/N: MMMMWWSSSSRRC A/C CODE: XXXX MADE IN PHILIPPINES 73-811-029 SERIAL NO.: Pin Assignments H HP PS S3 35 5 M Mo od du ul le e Top Bottom TOP SIDE 1-24 Pin Description Pin Description 1 AC (L) A AC (L) 2 BLANK B BLANK 1 23456789 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 3 AC (N) C AC (N) AB C D E F H J K L M N P R S T U V W X Y Z AA AB 4 BLANK D BLANK 5 GND E GND 6 SWP F -SENSE 7 5V RTN H +SENSE 8 COMMON J COMMON 9 COMMON K COMMON U Un ni it t C C C Co on nn ne ec ct to or r Car Card d E Ed dge C ge Connec onnect tor with gold finge or with gold finger rs s double-sided 1.6mm FR double-sided 1.6mm FR-4 PCB -4 PCB 10 COMMON L COMMON 11 COMMON M COMMON 12 COMMON N COMMON 13 COMMON P COMMON 14 V OUT R V OUT 15 V OUT S V OUT Mating c connector: 16 V OUT T V OUT EDAC 307-048-520-201 or 17 V OUT U V OUT equivalent 18 V OUT V V OUT 19 V OUT W V OUT Rating: 5A per contact 20 BLANK X INHIBIT 21 +5 STANDBY Y TBA 22 TBA Z AC OK 23 FAN MON AA DC OK 2 2 BB I C DATA 24 I C CLK P Pi in n 6 6 - S SW WP P (IN/OUT Signal) P Pi in n X X - M Mo od du ul le e I In nh hi ib bi it t (IN Signal) ( (S Si in ng gl le e W Wi ir re e P Pa ar ra al ll le el l) ) SWP Pin is used when connecting units in parallel to achieve current sharing. Current share accuracy is typically 10% of full load. P Pi in n Z Z - A AC C O OK K (OUT Signal) No Not te e: : SWP V SWP Volt oltage is 5V a age is 5V at t 100% lo 100% load c ad cu urre rren nt t P Pi in n 2 23 3 - F Fa an n M Mo on ni it to or r (OUT Signal) Note: Hi state: Source 100uA @ 4V Low State: Sink 10mA @ 0.5V P Pi in n A AA A - D DC C O OK K (OUT Signal) P Pi in n F F - --R Re em mo ot te e S Se en ns se e P Pi in n H H - + + R Re em mo ot te e S Se en ns se e Compensates for up to 0.5V drop. Recommended shielded twisted wire pair. 154 North America (USA): 1-888-41-ASTEC Europe (UK): 44 (1384) 842-211 Asia (HK): 852-2437-9662 rev 02.24.05 ASIA E EU UR RO OP PE E A AM ME ER RI IC CA AS S Units 2111-2116, Level 21 Astec House, Waterfront Business Park 5810 Van Allen Way Tower1, Metroplaza HPS35 Series Merry Hill, Dudley Carlsbad, CA 92008 223, Hing Fong Road West Midlands, DY5 1LX, UK Telephone: 760-930-4600 Fwai Fong, New Territories Telephone: 44 (1384) 842-211 Facsimile: 760-930-0698 Hong Kong Facsimile: 44 (1384) 843-355 Telephone: 852-2437-9662 Facsimile: 852-2402-4426 DRAWINGS Racks System Max. Size Max. System Module Standard Unit Code (H x W x L) Power Distribution Size Weight (lbs.) Watts 1400 (fully populated) HPR1 1.75" x 19.0" x 13.0" 1400 W (4 ea) HPS35 1U 8.6 Input Voltage 90-264 Module Used HPS35 Rack ID HPR1 HPR1 - Code Volts Output Amps L 12.0 116.8 Standard Options W 48.0 29.2 00 = No options 01 = Local sense H HP PR R1 1 -0 00 0 482.6 AC C Cord: (North America) 22.0 For all other countries, please contact factory. 1) Quail Electronics Series 5050 or equivalent (15A/125V) Supply End - NEMA 5-15P Equipment End - IEC 60320-C19 2) Quail Electronics Series 5052 or equivalent (20A/125V) Supply ENd - NEMA 5-20P Equipment End - IEC60320-C19 Blank P Panel: Astec P/N 73-686-000 + RTN 468.8 343.2 442.0 330.2 + RTN www.astecpower.com 155 31.7 13.4 25.0 43.7 HPR1-00 MAXIMUM OUTPUT POWER IS 1400W INPUT: OUTPUT: 90 - 240VAC - 40A +12V / 29A 50/60 Hz DATE: YYWW REV: XX S/N: MMMMWWSSSSRRC A/C CODE: XXXX MADE IN PHILIPPINES 73-810-002 SERIAL NO.: D-sub Connector Pin outs P Pi in n 2 2 + + R Re em mo ot te e S Se en ns se e D DC C O OK K (OUT Signal) P Pi in n 3 3 - R Re em mo ot te e S Se en ns se e Compensates for up to 0.5V drop. H HP PR R1 1 -0 00 0 Recommended shielded twisted wire Pin Description Pin Description pair. 1 5V Return (std-by) 20 I2C CLOCK P Pi in n 1 12 2 - G Gl lo ob ba al l A AC C O OK K (OUT signal) 2 + Remote Sense 21 I2C DATA 3 - Remote Sense 22 SWP Note: DC OK signals for each slot in the 4 5V Stand by 23 Unused (I2C_INT) rack is accessible in the D-sub 5 Unused 24 Module Inhibit connector (J18). Refer to Connector S 6 Module Inhibit 25 DC OK Pin-out table for pin assignments. Pin 1 L S 7 DC OK 26 AC OK is the Return Pin. O L 8 AC OK 27 I2C_ADD#1 T O 9 I2C_ADD#1 28 I2C_ADD#2 3 T Note: AC OK signals are OR'ed together A AC C O OK K (OUT Signal) 10 I2C_ADD#2 29 Fan Monitor 1 internally. If any module fails, the LED 11 Fan Monitor 30 Unused on the affected module will be off and 12 Global AC OK 31 Module Inhibit the logic signal will indicate AC NOT OK. S 13 Module Inhibit 32 DC OK L P Pi in n 1 19 9 - G Gl lo ob ba al l I In nh hi ib bi it t (IN signal) S 14 DC OK 33 AC OK O L 15 AC OK 34 I2C_ADD#1 T O 16 I2C_ADD#1 35 I2C_ADD#2 4 T 17 I2C_ADD#2 36 Fan Monitor 2 Note: AC OK signals for each slot in the 18 Fan Monitor 37 Unused rack is accessible in the D-sub connector (J18). Refer to Connector 19 Global Inhibit Pin-out table for pin assignments. Pin 1 Note: All outputs disabled when Pin 19 is the Return Pin. is open or High. Hi state: Source 100uA @ 4V Low State: Sink 10mA @ 0.5V P Pi in n 2 22 2 - S SW WP P (IN/OUT signal) SWP Pin is used when F Fa an n M Mo on ni it to or r (OUT Signal) connecting racks in parallel to achieve current sharing. Current share accuracy is typically 10% of full load. Note: SWP Voltage is 5V at 100% load current. Note: Fan Monitor signals for each slot M Mo od du ul le e I In nh hi ib bi it t (IN Signal) in the rack is accessible in the D-sub connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 is the Return Pin. PSU C Connector I2C_ADD#1 617-A-037-P-AJ-1-21 (Male socket) Amphenol I2C_ADD#2 Note: Module Inhibit signals for each TBD slot in the rack is accessible in the D-sub connector (J18). Refer to Connector Pin- out table for pin assignments. Pin 1 is Pin Out Diagram D-sub Connector (male) the Return Pin. Mating C Connector 617-A-037-S-AJ-1-20 (Female socket) Amphenol Pin Out Diagram D-sub Connector (female) 156 North America (USA): 1-888-41-ASTEC Europe (UK): 44 (1384) 842-211 Asia (HK): 852-2437-9662 rev 02.24.05