ASTEC DS1800-3
Specifications
+12V1 VDC
@147.5A
Input (PS)
90V to 264V
Operating Temperature
-10 to 50C
Performance Characteristics
Single
Total Max Current
164.2A
Volume
11.000"x4.200"x1.570"
Features
- 1U x 3U form factor (4 across in a 19" rack)
- Active AC inrush limit control
- Active Current Sharing
- Active Power Factory Correction
- HIgh Density 26.14 W/cu-in
- Hot Plug Operation
- I2C Communication
- No Min Load Required
- Smart Fan Speed Control
- Standard 3.3V standby voltage at 9A
Datasheet
Extracted Text
Embedded Power for Business-Critical Continuity Rev. 02.19.10_83 DS1800-3 1 of 4 DS1800-3 1800 Watts 12V Distributed Power System Distributed Power Bulk Front-End Total Output Power: 1800 Watts +12 Vdc main Output +3.3 Vdc Stand-by Output Wide Range Input voltage: 90 - 264 Vac Electrical Specifications Input Special Features Input ra nge 90 - 264 Vac (wide range) 90 - 264 1000 W load, nominal 100 Vac • Active power factor correction 180 - 264 1800 W load, nominal 200 Vac • EN61000-3-2 harmonic compliance Frequency 47-63 Hz, single phase AC • Active AC inrush control • 1U X 3U form factor Inrush current 55A maximum inrush current 3 • 24.7 W / in Efficiency >87% typical at full load, high line • +12 Vdc output Conducted EMI FCC Subpart J EN55022 Class B • +3.3 Vdc Stand-By (5 V standby - consult factory) Radiated EMI FCC Subpart J EN55022 Class B • No minimum load required Power factor 0.99 typical • Hot plug operation Leakage current 1.40 mA @ 240 Vac • N + 1 redundant • Internal OR’ing fets Hold up time 12 ms minimum • Active current sharing Output (10 - 100% load) Main DC voltage +12 V @ 147.5 A 180 - 264 Vac • Built-in cooling fans +12 V @83.0 A 90 - 264 Vac (40 mm x 28 mm) 2 Stand-By +3.3 Vsb @ 9 A (5 V @ 5 A TBA) • I C communication interface bus • EERPOM for FRU data Adjustment range Factory Set, no pot adjustments • Red/Green bi-color LED status +12 Vdc; ±5% Regulation • Internal fan speed control +3.3 Vsb; ±5% • INTEL, SSI Std. logic timing Over current +12 Vdc; latches off if overcurrent lasts over 1 second, • INTEL, SSI Std. FRU data format otherwise it is auto recovery (See ordering info next page) +3.3 vsb, • One year warranty 9 A max (same as +12Vdc) Over voltage +12 Vdc; 13.2 - 14.4 Vdc +3.3 Vsb; 3.76 - 4.30 Vdc Under voltage +12 Vdc; 9 - 10.8 V (latch off) Turn-on delay 2 Second max, 5 - 300 mS, Monotonic Rise Safety +12VOutput Rise Time 5 - 50 mS, Monotonic Rise • UL/cUL 60950 (UL Recognized) • NEMKO+ CB Report EN60950 • EN60950 • CE Mark • China CCC Embedded Power for Business-Critical Continuity Rev. 02.19.10_83 DS1800-3 2 of 4 Logic Control TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if PS_SEATED the PSU is removed PWR GOOD Active TTL LOW when output is within regulation limits. AC OK A LOW logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 2mS early warning signal before 12.0v DC output loss of regulation. PS_INHIBIT/PS_KILL This signal is connected to a short pin on the PSU When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin will be pull low by the system and turn the power supply on only after all other power supply pins have seated. Environmental Specifications Operating temperature: -10° to 50°C Storage temperature: -40°C to +85°C Altitude, operating: 10,000ft. Electromagnetic -EN61000-3-2, -3-3 susceptibility / Input transients: -EN61000-4-2, 4.3, 4-4, -4-5, 4-11 Level -EN55024:1998 RoHS & lead-free compliant (no tantalum caps.) Humidity: 20 to 90% RH, non-condensing Shock and vibration specificatons complies with Astec Std. Specifications, Q3205 MTBF (Demonstrated) 500 K Hrs at full load, 40°C Ordering Information Nominal Output Set Point Total Minimum Maximum Output Ripple Output Over Current Voltage Set Point Tolerance Regulation Current Current P/P 12.0 Vdc ±0.2% ±5% 0A 147.5 A 120 mV 120 - 130% of nominal DS1800-3 3.3 Vsb ±1% ±5% 0A 7.0 A 60 mV 100 - 125% of nominal *Over current latches off if overcurrent lasts over 1 seconds, otherwise it is auto recovery. *For 5 Vsb, consult marketing. Embedded Power for Business-Critical Continuity Rev. 02.19.10_83 DS1800-3 3 of 4 Mechanical Drawing Condition LED Status +3V3SB-ON; +12VOUT-OFF; AC PRESENT Blinking Green +3V3SB-ON, +12VOUT-ON Solid Green +12V_OCP, +12V_UVP, +48OVP Blinking Red FAN_FAULT, OTP, 3V3 OCP/UVP Solid Red Embedded Power for Business-Critical Continuity Rev. 02.19.10_83 DS1800-3 4 of 4 DC Output Connector Pinout / Functions Americas 5810 Van Allen Way Unit Connector; Molex Blade, (LPH Series) 45985-xxx Carlsbad, CA 92008 Mating Connector; Molex Blade, (LPH Series) SD-45984-1462 USA Telephone: +1 760 930 4600 Signal Descriptions Facsimile: +1 760 930 0698 Signal Pin Signal Pin Signal Signal Signal Signal Europe (UK) #Comp Side #Solder Side Function Description Function Description Waterfront Business Park Top Row Bottom Row Merry Hill, Dudley A17 SPARE A1 SPARE West Midlands, DY5 1LX A18 AC OK# AC input present A2 FAN FAIL# Fan Fail Signal United Kingdom 2 2 A19 A0 I C address bit 0 A3 FAIL I CFailure signal Telephone: +44 (0) 1384 842 211 2 2 Facsimile: +44 (0) 1384 843 355 A20 A2 I C address bit 2 A4 A1 I C address bit 1 2 2 A21 SCL I C Clock signal A5 SDA I C Data signal Asia (HK) A22 PWOK# Pwr OK output A6 PRESENT# Power supply present 14/F, Lu Plaza 2 Wing Yip Street A23 12LS 12V load share bus A7 PSON# Power enable input Kwun Tong, Kowloon A24 +12VRS Rtn +12V Rmt Sen Rtn A8 +12V RS +12V Remote Sense Hong Kong A25 3.3vsb Stand-By A9 3.3vsb Stand-By Telephone: +852 2176 3333 Facsimile: +852 2176 3888 A26 3.3vsb Stand-By A10 3.3vsb Stand-By A27 3.3vsb Stand-By A11 3.3vsb Stand-By For global contact, visit: A28 3.3vsb Stand-By A12 3.3vsb Stand-By www.PowerConversion.com A29 3.3vsb Rtn Stand-By return A13 3.3vsb Rtn Stand-By return techsupport.embeddedpower A30 3.3vsb Rtn Stand-By return A14 3.3vsb Rtn Stand-By return @emerson.com A31 3.3vsb Rtn Stand-By return A15 3.3vsb Rtn Stand-By return While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson A32 3.3vsb Rtn Stand-By return A16 3.3vsb Rtn Stand-By return Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Power Blade Power Blade PB1 Top +12vdc Main Output PB1 Bottom +12vdc Main Output PB2 Top +12vdc Main Output PB2 Bottom +12vdc Main Output Emerson Network Power. PB3 Top +12vdc Main Output PB3 Bottom +12vdc Rtn Main Output The global leader in enabling PB4 Top +12vdc Rtn Main Output PB4 Bottom +12vdc Rtn Main Output business-critical continuity. PB5 Top +12vdc Rtn Main Output PB5 Bottom +12vdc Rtn Main Output AC Power Connectivity DC Power Embedded Computing Embedded Power Signal Pin A1 Bottom Left Monitoring Signal Pin A17 Top Left Outside Plant Power Blade PB1 Bottom Left Power Switching & Controls Power Blade PB6 Top Left Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2010 Emerson Electric Co.
Frequently asked questions
What makes Elite.Parts unique?

What kind of warranty will the DS1800-3 have?

Which carriers does Elite.Parts work with?

Will Elite.Parts sell to me even though I live outside the USA?

I have a preferred payment method. Will Elite.Parts accept it?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods