process yellow 116 1375 1797 375 3405 313 2985 240 Embedded Power for Business-Critical Continuity 242 2607 Rev. 02.10.09_152 NLP110 Series 1 of 4 652 NLP110 Series Single and Triple Output Total Power: 80-110 Watts Input Voltage: 90-264 VAC # of Outputs: Single, Triple Electrical Specifications Special Features Input • Provides low voltage outputs Universal input Input range: 90-264 Vac • Compliance to EN61000-3-2 (See Note 6) (Power Factor = 0.98) Frequency: 47-63 Hz • 90 Vac to 264 Vac universal Input surge current: 120 Vac 18 A max. input range (cold start) 230 Vac 35 A max. • UL, CSA and VDE safety Safety ground 120 Vac, 60 Hz 0.45 mA approvals and CE-Marked to leakage current: 230 Vac, 50 Hz 0.75 mA LVD Input current: 120 Vac @ 80 W 0.9 A rms • Overvoltage and short circuit 120 Vac @ 110 W 1.3 A rms protection 230 Vac @ 80 W 0.48 A rms • VDE0871-B, EN55022-B, 230 Vac @ 110 W 0.7 A rms EN55011-B conducted noise Input fuse: UL/IEC127 F3.15A H, 250 Vac • VDE0871-A, EN55022-A, EN55011-A radiated noise Output • Meets all applicable and Total regulation: Main output ±2.0% relevant immunity standards (line and load) Auxiliary outputs ±5.0% EN61000-4-2,4,5 and 6 Rise time: At turn-on 1.0 s, max. • RoHS compliant Transient response: Main output 5.0% or 250 mV • 2 year warranty 75% to 100% max. dev., 1 ms max. step at 0.1 A µs recovery to 1% Temperature coefficient: ±0.02%/°C Overvoltage protection: Main outputs 125%, ±10% Safety Short circuit protection: Cyclic operation Continuous • VDE0805/EN60950/IEC950 File No. 10401-3336-1096 Minimum output current: Single and multiple See table All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. • UL1950 File No. E136005 • CSA C22.2 No. 950 File No. LR41062 • CCC Mark process yellow 116 1375 1797 375 3405 313 2985 240 242 Embedded Power for Business-Critical Continuity 2607 Rev. 02.10.09_152 EMC Characteristics NLP110 Series 2 of 4 652 Conducted emissions: EN55022, FCC part 15 Level B Radiated emissions: EN55022, FCC part 15 Level A Harmonic current emission correction: EN61000-3-2 Compliant ESD air: EN61000-4-2 Level 3 ESD contact: EN61000-4-2 Level 3 Surge: EN61000-4-5 Level 3 Fast transients: EN61000-4-4 Level 3 Radiated immunity: EN61000-4-3 Level 3 EN61000-4-6 Level 3 Conducted immunity: General Specifications Hold-up time: 120 Vac, 60 Hz 16.7 ms @ 110 W Efficiency: 120 Vac. 80 W (-9905J) 75% min. Isolation voltage: Input/output 3000 Vac Input/chassis 1500 Vac Approvals and standards pending: EN60950, VDE0805, IEC950, UL1950, CSA C22.2 No. 950 Weight: 283 g (10 oz) MTBF demonstrated: MIL-HDBK-217F 220,000 hours min. Environmental Specifications Thermal performance: Operating, ambient 0° C to +50 °C (see derating curve) Non-operating -40 °C to +85 °C 50 °C to 70 °C ambient convection cooled Derate to 50% load 0 °C to +50 °C, ambient convection cooled 80 W 0 °C to +50 °C, ambient, 150 LFM forced air 110 W Peak (0 °C to +50 °C, 60 s) (See Note 3) Relative humidity: Non-condensing 5% to 95% RH Altitude: Operating 10,000 feet max. Non-operating 30,000 feet max. Vibration (See Note 5): 5-500 Hz 2.4 G rms peak Shock per MIL-STD-810E 516.4 Part IV DERATING CURVE Output Power (Watts) 110W 150 LFM FORCED AIR COOLING 80W NATURAL 55W CONVECTION 40W COOLING 0C 10C 20C 30C 40C 50C 60C 70C process yellow 116 1375 1797 375 3405 313 2985 240 242 Embedded Power for Business-Critical Continuity 2607 Rev. 02.10.09_152 Ordering Information NLP110 Series  of 4 652 Output Total (6) (1) (2) (3) (4) (5) (7, 14, 15) Min Max 150 LFM 300 LFM Peak Ripple Model Numbers Voltage Regulation +5 V 0.5 A 15 A 22 A 22 A 22 A 50 mV ± 2.0% NLP110-9605J +12 V 0.3 A 6.4 A 9.2 A 9.2 A 11.5 A 120 mV ± 2.0% NLP110-9612J +48 V 0 A 1.6 A 2.3 A 2.3 A 2.5 A 240 mV ± 2.0% NLP110-9617J +24 V 0.2 A 3.2 A 4.6 A 4.6 A 6.0 A 240 mV ± 2.0% NLP110-9624J +5 V (A) 0.5 A 13 A 16 A 18 A 18 A 50 mV ± 2.0% NLP110-9693J +3.3 V (B) 0.2 A 13 A 16 A 20 A 20 A 50 mV ± 2.0% +12 V 0 A 0.65 A 1 A 1 A 1 A 120 mV ± 5.0% +3.3 V (A) 0.5 A 13 A 16 A 20 A 22 A 50 mV ± 2.0% NLP110-9694J +2.5 V (B) 0.1 A 13 A 16 A 20 A 22 A 50 mV ± 2.0% +12 V 0 A 0.65 A 1 A 1 A 1 A 120 mV ± 5.0% +12 V (A) 0.2 A 6.5 A 8.5 A 8.5 A 10 A 120 mV ± 2.0% NLP110-9695J +3.3 V (B) 0.5 A 13 A 16 A 20 A 22 A 50 mV ± 2.0% -12 V 0 A 0.65 A 1 A 1 A 1 A 120 mV ± 5.0% +12 V (A) 0.2 A 6.5 A 8.5 A 8.5 A 10 A 120 mV ± 2.0% NLP110-9608J +5 V (B) 0.2 A 13 A 16 A 18 A 22 A 50 mV ± 2.0% -12 V 0 A 0.65 A 1 A 1 A 1 A 120 mV ± 5.0% Notes 1 Free air convection. 7 For models NLP110-9608J and NLP110-9695J, the 12 V output is floating. Multiple output units: maximum continuous output power not to exceed For -12 V output, pin 11 on J2 has to be connected to Return making pin 12 80W. the -12 V output For -9693J; I = 13 A max.; I = 13 A max.; I +I ² 16 A. 8 Three orthogonal axes, random vibration 10 minutes for each axes, 2.4 G rms 3.3 V 5.0 V 3.3 V 5.0 V For -9694J; I = 13 A max.; I = 13 A max.; I +I ² 16 A 5 Hz to 500 Hz. 3.3 V 2.5 V 3.3 V 2.5 V For -9695J; I = 13 A max.; I = 6.5 A max.; I +I ² 16 A. 9 For optimum reliability, no part of the heatsink should exceed 110 ˚C, and no 3.3 V 12 V 3.3 V 12 V For -9608J; I = 13 A max.; I = 6.5 A max.; I +I ² 16 A. semiconductor case temperature should exceed 120 ˚C. 5.0 V 12 V 5.0 V 12 V Single output units: maximum continuous output power not to exceed; 75 W 10 CAUTION: Allow a minimum of 1 second after disconnecting line power on -9905J; 76.8 W on -9912J,-9924J, and -9917J. when making thermal measurements. 2 150 LFM forced air cooling from L4 side. 11 This product is only for inclusion by professional installers within other Multiple output units: maximum continuous output power not to exceed 105 equipment and must not be operated as a stand alone product. W. 12 The EMI specifications reference measurements made with the power supply For -9693J; I = 16 A max.; I = 16 A max.; I +I ² 20 A. mounted on a grounded metal sheet extending 1 inch beyond each edge, 3.3 V 5.0 V 3.3 V 5.0 V For -9694J; I = 16 A max.; I = 16 A max.; I +I ² 20 A using an unshielded cable. No external filtering required during conducted 3.3 V 2.5 V 3.3 V 2.5 V For -9695J; I = 16 A max.; I = 8.5 A max.; I +I ² 20 A. emissions testing but some applications may require additional filtering 3.3 V 12 V 3.3 V 12 V For -9608J; I = 16 A max.; I = 8.5 A max.; I +I ² 20 A. to achieve system compliance. A line choke, (ac input cords looped twice 5.0 V 12 V 5.0 V 12 V Single output units: maximum continuous output power not to exceed 110W through an EMI suppression toroid) was used during radiated emissions for all models. testing. Considerable radiated testing in 1U six-sided boxes has shown that 3 300 LFM forced air cooling from L4 side. units can meet level B in typical systems. Application support is available Multiple output units: maximum continuous output power not to exceed 110 from the factory to assist with EMI compliance. W. 13 All models require a minimum mounting stand-off of 6.35 mm (0.25 inches) For -9693J; I = 20 A max.; I = 18 A max.; I +I ² 22 A. in the end use product. 3.3 V 5.0 V 3.3 V 5.0 V For -9694J; I = 20 A max.; I = 20 A max.; I +I ² 22 A 3.3 V 2.5 V 3.3 V 2.5 V 14 The ‘J’ suffix indicates that these parts are Pb-free (RoHS 6/6) compliant. For -9695J; I = 20 A max.; I = 8.5 A max.; I +I ² 22 A. 3.3 V 12 V 3.3 V 12 V 15 NOTICE: Some models do not support all options. Please contact your local For -9608J; I = 20 A max.; I = 8.5 A max.; I +I ² 22 A. 5.0 V 12 V 5.0 V 12 V Emerson Network Power representative or use the on-line model number Single output units: maximum continuous output power not to exceed 110W search tool at http://www.PowerConversion.com/products. for all models. 4 Peak output current lasting less than 30 seconds with duty cycle less than 5%. During peak loading, output voltage may exceed total regulation limits. 5 Figure is peak-to-peak for convection power rating. Output noise measurements are made across a 20 MHz bandwidth using a 6’ twisted pair, terminated with a 10 µF electrolytic capacitor and a 0.1 µF ceramic capacitor. 6 Minimum load required for correct start-up and operation on single outputs and on main output of multiple versions. Failure to observe minimum load on main output will not allow the supply to start-up correctly. Some electronic test loads have a large delay time before they start drawing current even though the voltage from the supply is present. During this time delay, there is no load on the output and as a result, the supply cannot start- up properly and maintain its correct output voltage. In these instances, a dummy resistive load across the output may be necessary to load the output of the supply until the test load can function correctly and draw the intended minimum load. Minimum load required on auxiliary outputs to maintain regulation. process yellow 116 1375 1797 375 3405 313 2985 240 Embedded Power for Business-Critical Continuity 242 2607 Rev. 02.10.09_152 6.50 NLP110 Series (165.10) Americas 4 of 4 652 6.050 0.23 5810 Van Allen Way (153.670) (5.842) Carlsbad, CA 92008 USA J4 12 Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 2.550 (64.770) Europe (UK) J2 Waterfront Business Park ! Merry Hill, Dudley F1 3.00 T1 (REF.) West Midlands, DY5 1LX 1 (76.20) 1 3 J1 United Kingdom 1 J3 2 Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 2 ALL DIMENSIONS IN INCHES (mm) J5 1 Asia (HK) MAXIMUM COMPONENT HEIGHT 0.23 14/F, Lu Plaza IS 1.26 (32.00) (5.842) 2 Wing Yip Street Recommended direction 2 Kwun Tong, Kowloon for forced air relative to Hong Kong power supply orientation shown below. Telephone: +852 2176 3333 4 3 1 Optimum. Facsimile: +852 2176 3888 2 Very good. 3 Good. 1 For global contact, visit: 4 Not recommended. www.PowerConversion.com Input Pin Connections Output Pin Connections techsupport.embeddedpower @emerson.com J1 J2 Single Triple Pin 1 AC Neutral Pin 1 No Connection V (B) While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Pin 2 No Connection Pin 2 No Connection V (B) Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this Pin 3 AC Line Pin 3 No Connection V (B) information or for any errors or omissions. J3 Pin 4 Return Return Emerson Network Power. Pin 1 V (A) Sense + Pin 5 Return Return The global leader in enabling Pin 2 V (A) Sense - Pin 6 Return Return business-critical continuity. J4 Pin 7 Return Return AC Power Pin 8 V (A) V (A) Pin 1 Safety Earth Connectivity Pin 9 V (A) V (A) J5 DC Power Pin 10 V (A) V (A) Pin 1 V (B) Sense + Embedded Computing Pin 11 No Connection V (C) Pin 2 V (B) Sense - Embedded Power (7 Pin 12 No Connection V (C) Return Monitoring Input and output connectors Mating connectors Outside Plant AC (J1) connector type AC (J1) mating connector type Power Switching & Controls Molex 26-60-4030 or equivalent. valent. Molex 09-50-3031 or equivalent with Molex 08-50-0105 or equivalent crimp terminals. terminals. Precision Cooling DC (J2) connector type DC (J2) mating connector type Racks & Integrated Cabinets 12 position Molex Spox type 26-48 Molex Spox type 26-03-3121 and contact 08-52-0113. 08-52-0113. 1125 or equivalent. equivalent. Services Sense (J3) connector type Sense (J3) mating connector type Surge Protection Molex 22-23-2021 or equivalent. equivalent. Molex 22-01-3027 and contactt 08-50-0113. 08-50-0113. Earth (J4) connector type Earth (J4) mating connector type pe EmersonNetworkPower.com Male 0.250 quickck disconnect. disconnect. Molex 90028. Emerson Network Power and the Emerson Sense (J5) connector type Sense (J5) mating connector type Network Power logo are trademarks and service marks of Emerson Electric Co. Leoco co 2421P02H000. 2421P02H000. Leoco 2420S020000 and contact ntact 2453TPB00V1. 2453TPB00V1. ©2008 Emerson Electric Co.