ARTESYN NFS50-7608
Specifications
Altitude
Operating 10,000 feet max.
Approvals and standards
VDE0805, EN60950, IEC950 IEC1010, CSA C22.2 No. 950
Conducted emissions
EN55022, FCC part 15 Level A
Conducted immunity
EN61000-4-6, level 3 Perf. criteria 2
Efficiency
70%, typ.
ESD
air EN61000-4-2, level 3 Perf. criteria 1
ESD contact
EN61000-4-2, level 4 Perf. criteria 1
Fast transients
EN61000-4-4, level 3 Perf. criteria 2
Hold-up time
110VAC, 50W output power @ 16ms, 230VAC, 50W output power @ 100ms
Input frequency range
47 to 440Hz
Input surge current
110VAC, cold start 10A, max., 230VAC, cold start 20A max.
Input voltage range
Universal input: 85 to 264VAC, 120 to 370VDC
Isolation voltage
Input/output 3000VAC
LEAKAGE CURRENT
264VAC, 50Hz 0.4mA, max.
Line Regulation
LL to HL at max. load ±0.3%
MTBF
MIL-HDBK-217E, 25°C 160,000 hours
Output power limit
Primary power: 90W Pin max., limited: 60W Pout min.
Overshoot/undershoot
At turn-on 0%
Overvoltage Protection
+5V output 6.25V ±0.65V
Peak (30 seconds)
60W
Radiated emissions
EN55022, FCC part 15 Level A
Radiated immunity
EN61000-4-3, level 3 Perf. criteria 2
Relative humidity
Non-condensing 5% to 95% RH
Safety ground
132VAC, 60Hz 0.2mA, max.
Short Circuit Protection
Yes, with auto-restart
Surge
EN61000-4-5, level 3 Perf. criteria 1
Switching frequency
Variable 25kHz to 250kHz
Temperature Coefficient
All outputs ±0.03%/°C, max.
Thermal performance
Operating range 0°C to +70°C
Total regulation
Main output (output 1) ±2.5%, All other outputs ±5.0%
Transient Response
5V (2.5A to 5A) 500mV max. dev., 500µs recovery to 0.5%; 12V (1A to 2A) 300mV max. dev. 500µs recovery to 0.5%
Vibration
5Hz to 500Hz 2.4G rms (approx)
Voltage adjustability
+5V output ±3%, +12V tracks the 5V output
Weight
400g (14oz)
Features
- 50W with free air convection cooling
- 6.3 x 3.94 x 1.5 inch package (1U applications)
- EN55022, EN55011 conducted emissions level A
- Isolated output option
- NFS50 Medical IEC601 approved
- Overvoltage and short circuit protection
- Regulation to no load
- UL, VDE and CSA safety approvals
Datasheet
artesyn-NFS50-7608-datasheet-825209243.pdf
76 KiB
Extracted Text
NFS50-7608 Triple output • 6.3 x 3.94 x 1.5 inch package (1U applications) • Overvoltage and short circuit protection • 50W with free air convection cooling • Regulation to no load • Isolated output option • EN55022, EN55011 conducted emissions level A • UL, VDE and CSA safety approvals • NFS50 Medical IEC601 approved The NFS50-7608 is a 50W universal input AC/DC power supply on a 6.3 x 3.94 inch card with a maximum component height of 1.5 inches for use in 1U applications. The NFS50-7608 series can regulate on the auxiliary outputs down to no load making it suitable for applications that require a heavy logic load on the main 5V output and low nominal loads with high peak capability for drives, relays or switches on the auxiliary outputs. The NFS50-7608 provides 50W of output power with free air convection cooling which can be boosted to 60W with 20CFM of air. Standard features include overvoltage and short circuit protection. The series, with full international safety approval and the CE mark, meets conducted emissions EN55022 level A. The NFS50-7608 series is designed for use in low power data networking, computer, telecom and [ 2 YEAR WARRANTY ] industrial applications such as POS terminals, servers, PABX's, industrial PC's and process automation. SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated OUTPUT SPECIFICATIONS EMC CHARACTERISTICS Voltage adjustability +5V output ±3% ESD contact EN61000-4-2, level 4 Perf. criteria 1 +12V tracks the 5V output Surge EN61000-4-5, level 3 Perf. criteria 1 Fast transients EN61000-4-4, level 3 Perf. criteria 2 Line regulation LL to HL at max. load ±0.3% Radiated immunity EN61000-4-3, level 3 Perf. criteria 2 Conducted immunity EN61000-4-6, level 3 Perf. criteria 2 Total regulation Main output (output 1) ±2.5% All other outputs ±5.0% GENERAL SPECIFICATIONS (See Notes 5, 6) Hold-up time 110VAC, 50W output power 16ms Overshoot/undershoot At turn-on 0% 230VAC, 50W output power 100ms Transient response 5V (2.5A to 5A) 500mV max. dev. Efficiency 70%, typ. 500µs recovery to 0.5% Isolation voltage Input/output 3000VAC 12V (1A to 2A) 300mV max. dev. Input/chassis 1500VAC 500µs recovery to 0.5% Switching frequency Variable 25kHz to 250kHz Temperature coefficient All outputs ±0.03%/°C, max. Approvals and VDE0805, EN60950, IEC950 Overvoltage protection +5V output 6.25V ±0.65V standards IEC1010, CSA C22.2 No. 950 Output power limit Primary power 90W Pin max. Weight 400g (14oz) limited 60W Pout min. MTBF (See Note 7) MIL-HDBK-217E, 25°C 160,000 hours Short circuit protection Yes, with auto-restart ENVIRONMENTAL SPECIFICATIONS INPUT SPECIFICATIONS Thermal performance Operating range 0°C to +70°C Input voltage range Universal input 85 to 264VAC (See derating curve) 120 to 370VDC Non-operating –40°C to +85°C Input frequency range 47 to 440Hz 0°C to 50°C ambient temp., 50W Convection cooled Input surge current 110VAC, cold start 10A, max. 0°C to 50°C ambient, 60W 230VAC, cold start 20A max. Forced air @ 20 CFM 50°C to 70°C ambient Derate linearly Safety ground 132VAC, 60Hz 0.2mA, max. to 50% load leakage current 264VAC, 50Hz 0.4mA, max. Peak (30 seconds) 60W EMC CHARACTERISTICS Relative humidity Non-condensing 5% to 95% RH Conducted emissions EN55022, FCC part 15 Level A Altitude Operating 10,000 feet max. Radiated emissions EN55022, FCC part 15 Level A Non-operating 30,000 feet max. ESD air EN61000-4-2, level 3 Perf. criteria 1 Vibration (See Note 9) 5Hz to 500Hz 2.4G rms (approx) PAGE 1 ds_nfs50_20050826.PDF LOW TO MEDIUM POWER AC/DC POWER SUPPLIES | 50-60W AC/DC 50 to 60 Watt AC/DC universal input switch mode power supplies OUTPUT CURRENTS OUTPUT TOTAL MODEL (4) RIPPLE (1) (2) (3) (5,6) (12) VOLTAGE MAX PEAK FAN REGULATION NUMBER (6) +5.1V (I ) 5.0A 7.0A 7.0A 50mV ±2.5% NFS50-7608 1 +12.0V (I ) 2.0A 5.0A 2.5A 120mV ±5.0% 2 -12.0V 0.5A 1.0A 0.7A 120mV ±5.0% Notes PIN CONNECTIONS 1 Convection cooled, maximum 50W output power. 2 Peak outputs lasting less than 30 seconds with duty factor less than 10%. J1 NFS50-7608 During peak loading output may go outside total regulation limits. Pin 1 AC Line Maximum output during peak loading is 60 Watts. 3 Forced air, 20 CFM at 1 atmosphere. Pin 2 AC Neutral 4 Figure is peak-to-peak. Output noise measurements are across a 50MHz J2, J3, J4 bandwidth made using a 12” twisted pair, terminated with a 47µF capacitor. Pin 1 -12V 5Total regulation is defined as the static output regulation at 25°C, including Pin 2 +12V initial tolerance, line voltage within stated limits and output voltages adjusted to their factory settings. Also, for stated I(2) regulation: I(1)/I(2)≤5. Pin 3 Return 6A minimum load of 0.5 Amps is required on the +5.1V output to obtain full Pin 4 +5.1V current from the -12V output. 7 Derating curve is application specific for ambient temperatures > 50°C, for E1 o optimum reliability no part of the heatsink should exceed 110 C and no o Pin 1 Ground semiconductor case temperature should exceed 115 C. 8 Caution: Allow a minimum of 1 second after disconnecting the power when making thermal measurements. 9 Three orthogonal axes, random vibration, ten minute test for each axis. 10 A 5 Watt minimum load is recommended to achieve design MTBF. 11 This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 12 NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/products.htm to find a suitable 0.156 (3.96) Dia. 4 Places alternative. PIN1 MAX HEIGHT 38.1mm PIN1 J2 3.15 3.94 OUTPUT (80.0) J3 (100.1) AC mating connector ADJUST Molex 09-50-3031 or equivalent with Molex 08-50-0105 or equivalent crimp J4 PIN1 J1 E1 terminal. 2 1 DC mating connector Molex 22-01-1043 or equivalent with Molex 08-50-0031 or equivalent crimp terminal. 4.80 (121.9) 0.40 0.75 (10.2) 6.30 (19.0) (160.0) ALL DIMENSIONS ARE IN INCHES (mm) Maximum component height is 1.5 (38.1) DERATING CURVE Output Power (Watts) 60W 20 CFM FORCED AIR COOLING 50W 30W NATURAL CONVECTION 25W COOLING International Safety Standard Approvals VDE0805/EN60950/IEC950/IEC1010 File No. 10401-3336-1036 Licence No 1485 and 1650 5W MINIMUM LOAD REQUIRED TO ACHIEVE DESIGN MTBF UL1950 File No. E136005 0°C 10°C 20°C 30°C 40°C 50°C 60°C 70°C CSA C22.2 No. 950 File No. LR41062C Datasheet © Artesyn Technologies® 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. http://www.artesyn.com PAGE 2
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the NFS50-7608 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods