CL40 SERIES Single and triple output Recommended for new design-ins • 85VAC to 264VAC universal input range • Pre-approved SELV power solution • Up to 40W continuous output power • Up to 50W peak output power • UL, CSA, VDE and BABT approved • VDE0871-A conducted noise performance • Stand alone "listed" equipment The CL40 series is a family of 40W (50W peak) external switching power supplies. The CL40 enables the system specifier to optimise the design for several reasons. Firstly, because the power supply offers pre-approved SELV (Safety Extra Low Voltage) outputs, the submission of the apparatus for safety approval is simplified. This represents a significant saving of time and money. Secondly, the task of integrating the power supply into the mechanical design is eliminated, presenting further savings in time and money by ensuring a shorter and simpler design cycle. This means that your product gets to market faster. These advantages are complemented by universal input, CE mark, IEC950, UL, CSA, VDE and BABT approvals, to complete a worldwide packaged power [ 2 YEAR WARRANTY ] solution suitable for a wide variety of low power, desktop applications. SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated OUTPUT SPECIFICATIONS ELECTROMAGNETIC COMPATIBILITY SPECIFICATIONS Line regulation Single outputs ±0.2% Radiated emissions EN55022, EN55011, FCC Level B LL to HL, FL Multi's: +5.1V output ±0.2% Conducted emissions EN55022, EN55011, FCC Level A Multi's: aux. outputs ±1.0% Electrostatic discharge EN61000-4-2 Level 4 Electrostat. air discharge IEC801-2 Level 3 Total regulation Single outputs ±5.0% RF field susceptibility IEC801-3 Level 3 NL to FL (Note 5) Multi's: +5.1V output, ±5.0% Electrical fast EN61000-4-4 Level 3 Multi's: aux. outputs See table transients/bursts Surge susceptibility EN61000-4-5 Level 3 Overshoot/undershoot At turn-on 10% max. GENERAL SPECIFICATIONS Transient response +5.1V output ±250mV max. dev., (Single output model) (50% FL to 1ms recovery to 1% Hold-up time 110VAC 12ms 100% FL step) 230VAC 110ms Temperature coefficient All outputs ±0.02%/°C Efficiency 110VAC and 230VAC 70% typical Overvoltage protection +5.1V output only 6.25V ±0.75V Isolation voltage Input/output 3000VAC Input/chassis 1500VAC Output power limit Primary power limited 90W Pin max. 50W Pout min. Switching frequency Variable 20kHz to 70kHz Short Circuit Protection Continuous with Approvals and VDE0805, EN60950 auto-restart standards IEC950, IEC1010, UL1950 BABT, CSA C22.2 No. 950 INPUT SPECIFICATIONS Case material ABS plastic Input voltage range Note 1 85 to 264VAC Material flammability UL94V-0 Input frequency range 47 to 440Hz Weight 800g (28oz) Input surge current 110VAC 12A max. 230VAC 30A max. MTBF MIL-HDBK-217E 100,000 hours min. Safety ground 110VAC, 60Hz 0.2mA ENVIRONMENTAL SPECIFICATIONS leakage current 230VAC, 50Hz 0.4mA Thermal performance Operating 0°C to +40°C Non-operating –40°C to +85°C 0°C to 40°C ambient 40W Peak (0°C to 40°C, max. 60s) 50W Relative humidity Non-condensing 5% to 95% RH Altitude Operating 10,000 feet max. Non-operating 40,000 feet max. Vibration, 5Hz to 500Hz See Note 8 2.4G rms (approx) PAGE 1 DS_CL40_19980401.PDF AC/DC POWER SUPPLIES | 40W AC/DC 40 Watt AC/DC external power supplies (1) OUTPUT CURRENT OUTPUT TOTAL (4) RIPPLE MODEL NUMBER (5) VOLTAGE REGULATION (2) (3) MAX PEAK +5.1V (A) 3.0A 5.0A 50mV ±5.0% CL40-7608 +12.0V (B) 1.7A 3.0A 120mV -3.0%, +7.0% –12.0V 0.35A 1.0A 120mV ±5.0% +5.1V (A) 3.0A 5.0A 50mV ±5.0% CL40-7610 +15.0V (B) 1.3A 3.0A 150mV -2.0%, +5.0% –15.0V 0.35A 1.0A 150mV ±5.0% (7) +5.1V 5.0A 5.0A 50mV ±6.0% CL40-7605 CL40-7605J (7) +12.0V 3.3A 4.0A 120mV ±5.0% CL40-7612 CL40-7612J +13.5V 3.0A 3.7A 130mV ±5.0% CL40-7613 (7) +15.0V 2.7A 3.3A 150mV ±5.0% CL40-7615 CL40-7615J +16.5V 2.4A 3.0A 160mV ±5.0% CL40-7616 (7) +24.0V 1.6A 2.0A 240mV ±5.0% CL40-7624 CL40-7624J Notes PIN CONNECTIONS 1 For 230VAC operation a minimum output load of 4 Watts is required. 2 Natural convection cooling, 40W maximum. PIN NUMBER SINGLES -7608 -7610 3 Peak output current lasting less than 60 seconds with duty cycle less than 10%. During peak loading outputs may go outside of regulation limits. 1+V +5.1V +5.1V OUT Peak total power must not exceed 50W. 4 Figures are peak-to-peak. Output noise is measured across a 20MHz 2+V +12V +15V OUT bandwidth using a 12” twisted pair terminated with a 47μF capacitor. 5 Total regulation is defined as the static output regulation at 25°C, including 3 Return Return Return initial tolerance, load currents within stated limits, and output voltages adjusted to their factory settings. Also, for ‘B’ output stated regulation: 4 Return –12V –15V I(A)/I(B)<5. 6 The standard CL40 is IEC950/VDE0805 approved as a stand-alone power 5 Return Return Return supply. The plastic case incorporates an IEC 320 inlet receptacle. No input cable is supplied in Europe as standard. An input cable is supplied to customers in the US only. To order add the suffix ‘I’ to the end of the model number, e.g. CL40-7605I. 2.5mm BATTERY ELIMINATOR JACK In order to have a stand-alone power supply fully UL and CSA listed (as (SUFFIX 'J') opposed to certified or recognised) it is required that the manufacturer pro- vide an approved input cable with the power supply. 7 The standard output connector is a DIN41524 five-pin plug. As an alterna- tive single output models can be supplied with a 2.5mm battery eliminator jack. To order this option add the suffix “J” to the model number. Example: CL40-7612J. See the table above for availability. 8 Three orthogonal axes random vibration, 10 minute test for each axis. - NEGATIVE 72 6.5 (1829) (165) + POSITIVE 3.85 5 1 (98) 4 2 3 STANDARD OUTPUT CONNECTION (DIN 41524 FIVE PIN PLUG) 2.60 (66) International Safety Standard Approvals VDE0805/EN60950, IEC950, IEC1010 geprüfte File No. 10401-3336-1062 Licence No. 1062 Sicherhelt ALL DIMENSIONS ARE INCHES (mm) UL1950 File No. E136005 CSA C22.2 No. 950 File No. LR41062/LR50913/LR101320 Certificate No. PS/603191 http://www.artesyn.com PAGE 2