MODEL 2907 Electronic Enclosure Slide APPLICATIONS: Use model 2907 whenever an ultra-thin, medium Ball Bearing Movement duty, over travel, rack-mount slide is required. For use on electronic .38" [9.6mm] Width chassis, keyboards, fantrays, and other rack-mount applications. 1.62" [41.1mm] Height Accommodates chassis from 1U to 4U. This product is covered 2.00" [50.8mm] Over Travel by U.S. and various foreign patents issued and/or pending. * Up to 115 lb. [52.3 kg.] Capacity .213 [5.4] DIA. Thru Hole with .365 X .213 X .040 .63 3.04 6.04 [9.3 X 5.4 X 1.01] [15.9] [77.2] [153.4] Raised Emboss 1.74 1.25 [44.2] [31.8] TYP. .36 Clinch Nuts .50 1.25 1.50 1.25 [9.1] #8-32 TYP. [12.7] [31.8] [38.1] [31.8] TYP. REF. Ref. REF. REF. .69 [17.5] TYP. #8-32 Clinch Flush or At Nut (5X) .50 [12.7] Under Only Adjustable From Flush Slide Travel Plus 1.75 [44.5] or Flush or Under Minus 2.00 [50.8] 4.39 .192 X .413 [111.5] [4.9 X 10.5] Lock Out and 1.14 .38 .50 .38 2.39 TYP. Lever Disconnect [29.0] [9.6] [12.7] [9.5] [60.7] .192 DIA. .180 X .725 .50 3.00 .50 Slot Not Available On [4.9] TYP. [4.6 X 18.4] [12.7] [76.2] [12.7] 12" [305] Slide Length TYP. 1.62 [41.1] A .35 Access .180 X 2.74 .180 X 1.49 B [8.9] Slots [4.6 X 69.6] [4.6 X 37.8] C TYP. .39 D .180 [4.6] [9.9] E DIA. (2X) F Slide Length Minus .050 [1.3] Slide Length INCHES [mm] Finish Clear electroplate (C) finish Load * Part Slide Slide Rating AB C D E F Length 12" to 30" [305mm to 762mm] Number Length Travel per Pair lb. [kg.] Height 1.62" [41.1mm] 12.00 14.00 60 lb. 9.25 2907-12 [305] [356] [27.2 kg.] [235.0] Load See chart * 14.00 16.00 80 lb. 11.25 2907-14 ¤ Side Space .38" ± 0.030 [9.6mm ± 0.76mm] [356] [406] [36.3 kg.] [285.8] ** 16.00 18.00 100 lb. 6.40 13.25 2.00" [50.8mm] Over travel 2907-16 Travel [406] [457] [45.4 kg.] [162.6] [336.5] 18.00 20.00 115 lb. 6.49 12.38 15.25 Mounting Chassis Member: #8 pan head screw 2907-18 [457] [508] [52.2 kg.] [164.8] [314.3] [387.3] Outer Member: Adjustable front and 20.00 22.00 114 lb. 6.78 8.00 14.03 17.25 2907-20 [508] [559] [51.7 kg.] [172.1] [203.2] [356.2] [438.1] rear mounting brackets 22.00 24.00 112 lb. 8.39 16.03 19.25 2907-22 Unhanded, lock-out and disconnect, Features [559] [610] [50.8 kg.] [213.0] [407.0] [488.9] lead-in pins 24.00 26.00 110 lb. 10.00 10.78 18.03 21.25 2907-24 [610] [660] [49.9 kg.] [254.0] [273.7] [457.8] [539.7] 26.00 28.00 110 lb. 5.53 9.15 10.60 16.40 20.03 23.25 2907-26 Load rating based on a 16" [406mm] wide [660] [711] [49.9 kg.] [140.3] [232.4] [269.1] [416.6] [508.6] [590.5] * chassis cycled 2,000 times. 28.00 30.00 110 lb. 7.53 11.15 12.00 18.40 22.03 25.25 2907-28 ¤Brackets behind EIA rail with square holes. [711] [762] [49.9 kg.] [191.1] [283.2] [304.8] [467.4] [559.4] [641.4] No lateral adjustment with EIA rails using 30.00 32.00 110 lb. 9.53 12.60 20.40 24.03 27.25 ** 2907-30 round or tapped holes. [762] [813] [49.9 kg.] [241.9] [319.9] [518.2] [610.2] [692.1] Installation Instructions 1. Slide chassis member (smallest) is removable. Separate Figure 1 slide members by lifting left hand side lever up, and right Cabinet Rail with hand side lever down. Keep slide chassis members with Square Holes original outer members. Bracket Face 2. Slide has front and rear adjustable EIA brackets. Attach Emboss Emboss front brackets to outer slide member using #8-32 machine Provides #8-32 screws by aligning access slots on brackets to outer Vertical Alignment Threads (No Bar member holes. Front brackets can be mounted flush or 1/2" Within Square Holes. Nut Required) [12.7mm] back from front of slide based on user needs. 3. Establish distance from front cabinet rail to rear cabinet rail and attach rear brackets to slide. Do not fully tighten rear bracket mounting screws until final adjustment is made. Bar Bar 4. Insert removable locator pin into center hole of brackets. Nut Nut 5. Slide will mount to various cabinet rails at various locations on side of chassis. See illustrations at right. 6. Place slide into desired position and fully extend against EIA rails. Locator pins will support slide and bar nut while attaching screws. Front of Rail Behind Rail .44" [11.1] (Recommended) 7. Attach slide to EIA rail with #10-32 screws and fasten with Side Space Required bar nuts. Once screws are secure, remove locator pins. Do not fully tighten screws until final adjustment is made. 8. Mount slide chassis members (smallest) to the chassis. Figure 2 9. With cabinet members in the open or closed position, Cabinet Rail with bring ball retainer to full forward position. Install chassis by Tapped Holes engaging the slide members and close completely. Locks will engage on initial insertion and must be released Front of Rail to fully close. Check slide alignment by opening and closing the chassis. Any sign of binding indicates lateral Removable Locator stress or misalignment. Pin Supports Slide 10. Adjust slide position until movement is smooth. Tighten all Front of Rail During Installation .44" [11.1] screws and complete installation. Side Space Required NOTE: To remove chassis, lift the lever on the left hand slide up and the lever on the right hand slide down. Figure 3 Bar Nut Slide Ordering Instructions Cabinet Rail with Round Holes Complete your order for Accuride Model 2907 by specifying the following information. For example: Front of Rail 10 Pair C 2907 -18 D Required Slides Removable Locator Slide Finish Behind Rail Pin Supports Slide Slide Model (Recommended) During Installation Slide Length Optional Polybag Packaging Optional Mounting Bracket Kit Figure 4 Optional mounting bracket kit, part number 4180-0430-XE, 1/2" includes (2) front brackets, (2) rear brackets, (4) bar nuts, (4) locator pins, (8) #8-32 bracket-to-slide mounting screws, and 5/8" For 2U to 4U spacing, (8) #10-32 bracket-to-rail mounting screws packaged in a 1U slides can mount to polybag. 5/8" chassis (drawer) at Kits ordered separately. Order 1 kit per pair of slides. various locations 1/2" relative to the EIA rail Packaging 1/2", 5/8", 5/8" pitch pattern. Bulk (P) Pack: All lengths are packaged 10 pair per box. Optional mounting bracket kits (4180-0430-XE) are ordered and packaged separately. Distributor (D) Pack: All lengths are packaged 5 pair per box. Polybag packaging includes one pair of slides, one mounting ACCURIDE INTERNATIONAL INC. bracket kit (4180-0430-XE), and installation instructions. 12311 Shoemaker Avenue Santa Fe Springs, CA 90670 Specifications TEL (562) 903-0200 Slide members and ball retainers: Cold rolled steel FAX (562) 903-0208 Ball bearings: Carburized steel www.accuride.com Note: Specifications, materials, prices, terms, and delivery Manufacturing, Engineering, and Sales are subject to change without notice. United States • Germany • Japan • Mexico • United Kingdom Copyright © 2002 Accuride International Inc. Printed in U.S.A. 3700-1085(9456)-MK537-R3-0803 Copyright © 2002 Accuride International Inc. Printed in U.S.A. 3700-9456(1085)-MK091-R3-0803