175-300 Watts xppower.com HUL Series • Compact Size, Low Profile 3 • Up to 5.85 W/in Power Density • Single & Multiple Outputs • Convection-cooled Ratings • Remote On/Off • Power Fail Detect • 12 V Fan Supply Specification Input General Input Voltage • 90-132 VAC, 180-264 VAC (auto-ranging) Efficiency • 80% typical Input Frequency • 47-63 Hz Isolation • 3000 VAC Input to Output, 1500 VAC Input to Ground, Input Current • HUL175: 4.4 A max at 115 VAC, 500 VAC Output to Ground 2.2 A max at 230 VAC HUL200: 5.0 A max at 115 VAC, Switching Frequency • 42 kHz typical 3 3 2.5 A max at 230 VAC Power Density • HUL175: 4.51 W/In , HUL200: 5.85 W/In , 3 HUL300: 6.3 A max at 115 VAC, HUL300: 4.41 W/In 3.15 A max at 230 VAC Power Fail Detect • On = Logic high 100-500 ms after outputs Inrush Current • 35 A at 115 VAC, 70 A max at 264 VAC with regulation +25 °C cold start Fail = Logic low at least 1 ms prior to loss Power Factor • Passive PFC, meets EN6100-3-2, -3 of output Earth Leakage Current • <1.5 mA at 230 VAC / 50 Hz MTBF • 100 kHrs per MIL-HDBK-217F Output Environmental Output Voltage • See tables Operating Temperature • 0 °C to +60 °C, derate linearly from 100% Output Voltage Trim • ±5% on output 1 at +40 °C to 50% at +60 °C Initial Set Accuracy • ±1% max for single/main output Cooling • See notes ±5% for auxiliary outputs Operating Humidity • 5-90% RH, non-condensing Minimum Load • See tables & note 1 for 175 W model Storage Temperature • -20 °C to +85 °C Start Up Delay • 1 s max Operating Altitude • 3000 m Start Up Rise Time • 20 ms max Shock • 15 g (non-operation), 11 ms (half sine Hold Up Time • >15 ms at 115 VAC wave), 3 times for each axis Total Regulation • ±1% max for single output models, Vibration • 10-55 Hz (non-operation) 2 g, sweep time ±5% max for multiple output models 3 mins, 60 mins/axis Over/Undershoot • <5% max EMC & Safety Transient Response • 5% max deviation, recovery to within 1% in 500 µs for a 50% load change Emissions • EN55022 and FCC, level B Ripple & Noise • 1% pk-pk (50 mV max for 3.3 V output) (level A - 300 W) conducted Overvoltage Protection • 130% on output 1 only, recycle input to Harmonic Currents • EN61000-3-2 reset Voltage Flicker • EN61000-3-3 Overtemperature • Shuts down when ambient temperature ESD Immunity • EN61000-4-2, level 4 Perf Criteria A Protection exceeds +85 °C, auto recovery Radiated Immunity • EN61000-4-3, level 3 Perf Criteria A Overload Protection • 110-135% of total power, auto recovery EFT/Burst • EN61000-4-4, level 3 Perf Criteria A Short Circuit Protection • Trip and restart (Hiccup mode) Surge • EN61000-4-5, level 3 Perf Criteria A Temperature • ±0.1%/°C Conducted Immunity • EN61000-4-6, 10 V Perf Criteria A Coefficient Dips & Interruptions • EN61000-4-11, 30% 10 ms, Remote Sense • HUL175 only. Compensates for 0.5 V drop 70% 100 ms, 95% 5000 ms, on 3.3 V output Perf Criteria A, B, B Remote On/Off • On = Logic High or Open Safety Approvals • EN60950, UL60950, CSA22.2 No. 950 Off = Logic Low or Short per cUL, CE Mark Not available on HUL175 Fan Output • 12 V, 300 mA AC-DC AC-DC HUL175 Models and Ratings Output 1 Output 2 Output 3 Output 4 Model Voltage Conv Max Voltage Conv Max Voltage Conv Max Voltage Conv Max Number Nom Cooled 18.7 CFM Nom Cooled 18.7 CFM Nom Cooled 18.7 CFM Nom Cooled 18.7 CFM 5.0 V 10.0 A 15.0 A 3.3 V 10.0 A 20.0 A 12.0 V 2.2 A 3.0 A -5.0 V 0.7 A 1.0 A HUL175-40-3† 5.0 V 10.0 A 15.0 A 3.3 V 10.0 A 20.0 A 12.0 V 2.2 A 3.0 A -12.0 V 0.7 A 1.0 A HUL175-42-3† 5.0 V 10.0 A 15.0 A 3.3 V 10.0 A 20.0 A 24.0 V 1.5 A 2.0 A -12.0 V 0.7 A 1.0 A HUL175-45-3† 5.0 V 10.0 A 15.0 A 3.3 V 10.0 A 20.0 A 15.0 V 2.2 A 3.0 A -15.0 V 0.7 A 1.0 A HUL175-46-3† Notes 1. Minimum load is 2.0 A for V1, 0.0 A for V2 & V4, and 0.3 A for V3. 2. Total regulation for V1, V2 and V3 = ±5%; V4 = ±3%. Total regulation includes tolerance, line regulation and load regulation. 3. Total combined output power for the 3.3 V and 5.0 V not to exceed 126 W with 18.7 CFM or 70 W with convection cooling. 4. Maximum load continuous output power is 175 W with minimum 18.7 CFM forced air cooling or 100 W with convection cooling. 5. Outputs are fully isolated. † Available from Farnell. See pages 204-206. Mechanical Details All dimensions are in inches (mm). Tolerance: 0.02 (0.5) max. Weight: 1.32 lbs (600 g) approx. 0.65 0.2 (16.5) (5.1) B M3 x 0.5 STAND OFF 4 PLACES 2 P2 1 A M4 x 0.7 NUT FASTENER 8 PLACES 24 3.80 P1 (96.5) G N P3 2.50 L (63.5) 1 P2 Connector A Pin Function 1 Fan + 2 Fan - B 6.40 (162.5) P3 Connector Pin Function 1 +3.3 V Sense+ 4.58 (116.3) 2, 14 Output 2 2.90 (73.7) 3, 15 Output 2 0.80 4, 16 Return (20.3) 5, 17 Return 6, 18 Return A A 7, 19 Output 1 1.50 8, 20 Output 1 1.25 (38.1) 9, 21 Output 3 (31.8) 10, 22 Return 11,23 Output 4 12 Power Fail Detect 5.20 (132.1) 0.24 13 +3.3 V Sense- 6.00 (152.4) (6.00) 24 Return 6.80 (172.7) Notes 1. Input connector P1 mates with Molex housing 09-91-0500 and Molex 2478/2578/8818 series crimp terminal. 2. Output connector P3 mates with Molex housing 39-01-2240 and Molex 44476 series crimp terminal. 3. Fan connector P2 mates with JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. Fan output is 12 V/160 mA. 4. Covered versions are available, add suffix: ‘-C’ to model number for cover only, dimensions: 3.80” x 6.80” x 1.66” (96.5 x 172.7 x 42.1 mm), add suffix: ‘-FC’ to model number for fan cover, dimensions: 3.80” x 6.80” x 2.48” (96.5 x 172.7 x 63.0 mm). 5. Cable harnesses with 11.81” (300 mm) wire available, order part HUL175 LOOM KIT†. For mating connectors only, order part HUL175 CONN KIT†. 6. Covers are available separately. Order part HUL175 COVER† or HUL175 F/COVER† for Fan Cover. 7. Max penetration of screws 0.12” (3.0 mm). HUL200 Models and Ratings (3) Output 1 Output 2 Output 3 Output 4 Model Current Current Current Current Voltage Voltage Voltage Voltage (1) Number Nom Min Max Nom Min Max nom Min Max nom Min Max 3.3 V 0.5 A 30.0 A HUL200-10-1† 5.0 V 0.5 A 40.0 A HUL200-10† 12.0 V 0.5 A 16.7 A HUL200-12† 15.0 V 0.5 A 13.3 A HUL200-13† 24.0 V 0.5 A 8.3 A HUL200-14† 48.0 V 0.5 A 4.1 A HUL200-18† +5.0 V 0.5 A 20.0 A +12.0 V 0.0 A 8.0 A HUL200-23† +5.0 V 0.5 A 20.0 A +15.0 V 0.0 A 6.6 A HUL200-24† +5.0 V 0.5 A 20.0 A +24.0 V 0.0 A 4.2 A HUL200-25† +5.0 V 0.5 A 20.0 A +12.0 V 0.0 A 8.0 A F 12.0 V 0.0 A 1.0 A HUL200-31† +5.0 V 0.5 A 20.0 A +15.0 V 0.0 A 5.0 A F 15.0 V 0.0 A 1.0 A HUL200-32† +5.0 V 0.5 A 20.0 A +12.0 V 0.0 A 6.0 A -5.0 V 0.0 A 1.0 A F 12.0 V 0.0 A 1.0 A HUL200-40† +5.0 V 0.5 A 20.0 A +24.0 V 0.0 A 3.0 A -12.0 V 0.0 A 1.0 A F 12.0 V 0.0 A 1.0 A HUL200-45† +5.0 V 0.5 A 20.0 A +15.0 V 0.0 A 5.0 A -5.0 V 0.0 A 1.0 A F 15.0 V 0.0 A 1.0 A HUL200-46† +12.0 V 0.5 A 3.0 A +36.0 V 0.0 A 5.0 A +5.0 V 0.0 A 3.0 A -12.0 V 0.0 A 1.0 A HUL200-47 +5.0 V 0.5 A 5.0 A +36.0 V 0.0 A 2.5 A +12.0 V 0.0 A 1.0 A -12.0 V 0.0 A 1.0 A HUL200-47-2 +5.0 V 0.5 A 3.0 A +24.0 V 0.0 A 8.0 A +12.0 V 0.0 A 0.1 A -12.0 V 0.0 A 0.1 A HUL200-47-3 +5.0 V 0.5 A 5.0 A +12.0 V 0.0 A 2.5 A +24.0 V 0.0 A 2.5 A -12.0 V 0.0 A 1.0 A HUL200-47-1 Notes 1. Use part number UL200-XX for product without harmonic correction. e.g.: UL200-10. 2. Total output power for HUL200-10-1 is 73 W convection-cooled, 100 W with 18.7 CFM forced air cooling. 3. Output 4 is floating except for -47 models. It can be connected externally for positive or negative output. 4. Total output power for HUL200 single output models is 150 W convection-cooled, 200 W with 18.7 CFM forced air cooling. 5. Total output power for HUL200 multi output models is 100 W convection-cooled, 200 W with 18.7 CFM forced air cooling. 6. Tolerance 5% all outputs, except single output units - tolerance 2%. † Available from Farnell. See pages 204-206. Mechanical Details All dimensions are in inches (mm). Tolerance: 0.02 (0.5) max. Weight: 1.76 lbs (800 g) approx. 1.25 2.5 (63.5) (31.8) P2 Connector Mounting holes: L N G Pin Single Output Multi Output A: M4 x 0.7, 8 places A A 1 B B: 6-32, 8 places 1 Output 1 Output 3 P1 B B 2 Output 1 Return A 3 Output 1 Return 4 Output 1 Return 5 Output 1 Return 6 Output 1 Output 1 6.40 (162.5) 7 Return Output 1 5.77 8 Return Output 1 (146.7) 9 Return Output 1 6.80 10 Return Output 2 (172.7) 11 Return Output 4 12 Return Output 4 Return P3 Connector Pin Single Output Multi Output A 1 Fan + Multi-outputs have 3 B FAN B P2 separate 2 pin B P3 2 Return connectors for Fan, A 3 Return A Pin 1 Pin 1 Power Good and Remote 1.27 3.80 (96.5) 4 Power Fail Detect (32.3) ±0.3 (7.6) ON/OFF. These are (7) 5 Remote On/Off clearly marked on the 1.50 6 Return - PCB. (38.1) Notes 1. Input connector P1 mates with Molex housing 09-91-0500 and Molex 2478/2578/8818 series crimp terminal. 2. Output connector P2 mates with Molex housing 09-91-1200 and Molex 2478/2578/8818 series crimp terminal. 3. Fan connector mates with JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. 4. Signals connector P3 mates with JST housing XHP-6 and JST SXH-002T-P0.6 crimp terminals or 3 off JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. 5. Covered versions are available: add suffix: ‘-C’ to model number for cover only - dimensions: 3.80” x 6.80” x 1.66” (96.5 x 172.7 x 42.1 mm), add suffix: ‘-FC’ to model number for fan cover - dimensions: 3.80” x 6.80” x 2.48” (96.5 x 172.7 x 63.0 mm). 6. Covers are available separately. Order part HUL200 COVER† or HUL200 F/COVER† for Fan Cover. 7. Output is turned off by taking the Remote On/Off pin low (connect to Return). 8. Cable harnesses with 11.81” (300 mm) wire available, order part number HUL200 LOOM-S for single output models, HUL200 LOOM-D for dual output models, HUL200 LOOM-T for triple output models or HUL200 LOOM-Q for quad output models. 9. For mating connectors only, order part HUL200 CON KT†. 10. Max penetration of screws 0.12” (3.0 mm) AC-DC AC-DC HUL300 Models and Ratings (2) Output 1 Output 2 Output 3 Output 4 Model Current Current Current Current Voltage Voltage Voltage Voltage (1) Number Nom Min Max Nom Min Max nom Min Max nom Min Max 3.3 V 0.5 A 60.00 A HUL300-10-1† 5.0 V 0.5 A 60.00 A HUL300-10† 12.0 V 0.5 A 25.00 A HUL300-12† 15.0 V 0.5 A 20.00 A HUL300-13† 24.0 V 0.5 A 12.50 A HUL300-14† 48.0 V 0.5 A 6.25 A HUL300-18† +5.0 V 0.5 A 30.00 A +12.0 V 0.0 A 12.5 A HUL300-23† +5.0 V 0.5 A 30.00 A +15.0 V 0.0 A 10.0 A HUL300-24† +5.0 V 0.5 A 30.00 A +24.0 V 0.0 A 6.3 A HUL300-25† +5.0 V 0.5 A 30.00 A +12.0 V 0.0 A 10.5 A F 12.0 V 0.0 A 2.0 A HUL300-31† +5.0 V 0.5 A 30.00 A +15.0 V 0.0 A 8.0 A F 15.0 V 0.0 A 2.0 A HUL300-32† +5.0 V 0.5 A 30.00 A +12.0 V 0.0 A 10.0 A -5.0 V 0.0 A 2.0 A F 12.0 V 0.0 A 2.0 A HUL300-40† +5.0 V 0.5 A 30.00 A +24.0 V 0.0 A 4.3 A -12.0 V 0.0 A 2.0 A F 12.0 V 0.0 A 2.0 A HUL300-45† +5.0 V 0.5 A 30.00 A +15.0 V 0.0 A 7.4 A -5.0 V 0.0 A 2.0 A F 15.0 V 0.0 A 2.0 A HUL300-46† Notes 1. Use part number UL300-XX for product without harmonic correction. e.g. UL300-10. 2. Output 4 is floating. It can be connected externally for positive or negative output. 3. Total output power for HUL300-12,13,14,18 models is 200 W convection-cooled, 300 W with 30 CFM forced air cooling. 4. Total output power for all other HUL300 models is 150 W convection-cooled, 300 W with 30 CFM forced air cooling. 5. Tolerance 5% all outputs, except single output units - tolerance 2%. † Available from Farnell. See pages 204-206. Mechanical Details All dimensions are in inches (mm). Tolerance: 0.02 (0.5) max. Weight: 2.20 lbs (1.0 kg) approx. 0.25 (6.35) 2.50 (63.5) P2 Connector 0.50 P1 (12.7) Pin Single Output Multi Output 1.09 L N G (27.8) 1 Output 1 Output 3 2 Output 1 Output 1 3 Output 1 Output 1 M4 x 0.7 NUT FASTENER (12 PLACES) 4 Output 1 Output 1 5 Output 1 Output 1 6 Output 1 Return 8.00 (203.2) 7 Output 1 Return 7.50 8 Return Return (190.5) 7.00 (177.8) 9 Return Return 5.81 10 Return Return (147.6) 11 Return Output 2 12 Return Output 2 13 Return Output 4 14 Return Output 4 Return P3 Connector Pin Single Output Multi Output 1 Fan + Return (7) 2 Return DC OK P3 3 DC OK Return PIN 1 P2 (6) 4 Power Fail Detect Remote On/Off (6) 1 14 FAN 5 Remote On/Off Return 1.00 0.25 6 Return Power Fail Detect 4.25 (108.0) (25.4) (6.4) 2.00 (50.8) Notes 1. Input connector P1 mates with Molex housing 09-91-0500 and Molex 2478/2578/8818 series crimp terminal. 2. Output connector P2 mates with Molex housing 09-91-1400 and Molex 2478/2578/8818 series crimp terminal. 3. Fan connector mates with JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. Multiple outputs only. 4. Signals connector P3 mates with JST housing XHP-6 and JST SXH-002T-P0.6 crimp terminals. 5. Covered versions are available, add suffix: ‘-C’ to model number for cover only, dimensions: 4.25” x 8.00” x 2.16” (108.0 x 203.2 x 54.8 mm) add suffix: ‘-FC’ to model number for fan cover, dimensions: 4.25” x 8.00” x 3.00” (108.0 x 203.2 x 75.7 mm). 6. Output is turned off by taking the Remote On/Off pin low (connect to Return). 7. DC OK is a open collector output. Low = normal operation. 8. Cable harnesses with 11.81” (300 mm) wire available, order part number HUL300 LOOM-S for single output models, HUL300 LOOM-D for dual output models, HUL300 LOOM-T for triple output models or HUL300 LOOM-Q for quad output models. For mating connectors only, order part HUL300 CON KT†. 9. Covers are available separately. Order part HUL300 COVER† or HUL300 F/COVER† for Fan Cover. 10. Max penetration of screws 0.12” (3.0 mm). 17-Apr-07