175-300 Watts xppower.com HUL Series • Compact Size, Low Profile 3 • Up to 5.85 W/in Power Density • Single and Multiple Outputs • Convection-Cooled Ratings • Remote On/Off • Power Fail Detect • International Safety Approvals Specification Input General Input Voltage • 90-132 VAC, 180-264 VAC (auto-ranging) Efficiency • 80% typical Input Frequency • 47-63 Hz Isolation • 3000 VAC Input to Output 1500 VAC Input to Ground Input Current • HUL175: 4.4 A max at 115 VAC, 500 VAC Output to Ground 2.2 A max at 230 VAC HUL200: 5.0 A max at 115 VAC, Switching Frequency • 42 kHz typical 3 3 2.5 A max at 230 VAC Power Density • HUL175: 4.51 W/In , HUL200: 5.85 W/In , HUL300: 6.3 A max at 115 VAC, 3 HUL300: 4.41 W/In 3.15 A max at 230 VAC Power Fail Detect • On = Logic high 100-500 ms after outputs Inrush Current • 35 A at 115 VAC, 70 A max at 264 VAC with regulation +25 ºC cold start Fail = Logic low at least 1 ms prior to loss Power Factor • Passive PFC, meets EN6100-3-2, -3 of output Earth Leakage Current • < 1.5 mA at 230 VAC / 50 Hz MTBF • 100 kHrs per MIL-HDBK-217F Output Environmental Output Voltage • See tables Operating Temperature • 0 ˚C to +60 ˚C, derate linearly from 100% Output Voltage Trim • ±5% on output 1 at +40 ˚C to 50% at +60 ˚C Initial Set Accuracy • ±1% max for single/main output Cooling • See notes ±5% for auxiliary outputs Operating Humidity • 5-90% RH, non-condensing Minimum Load • See tables and note 1 for 175 W model Storage Temperature • -20 ˚C to +85 ˚C Start Up Delay • 1 s max Operating Altitude • 3000 m Start Up Rise Time • 20 ms max 2 Vibration • 5 Hz to 50 kHz, 7.35 m/s on 3 axis Hold Up Time • >15 ms at 115 VAC Total Regulation • ±1% max for single output models, EMC & Safety ±5% max for multiple output models Emissions • EN55022 and FCC, level B Over/Undershoot • <5% max (level A - 300 W) conducted Transient Response • 5% max. deviation, recovery to within Harmonic Currents • EN61000-3-2, class B 1% in 500 µs for a 50% load change Voltage Flicker • EN61000-3-3 amendments 1 & 2 Ripple & Noise • 1% pk-pk (50 mV max for 3.3 V output) ESD Immunity • EN61000-4-2, level 4 Perf Criteria B Overvoltage Protection • 130% on output 1 only, recycle input to Radiated Immunity • EN61000-4-3, level 3 Perf Criteria B reset EFT/Burst • EN61000-4-4, level 3 Perf Criteria B Overtemperature • Shuts down when ambient temperature Surge • EN61000-4-5, level 3 Perf Criteria B Protection exceeds +85 ˚C, auto recovery Conducted Immunity • EN61000-4-6, 10 V Perf Criteria B Overload Protection • 110-135%, auto recovery Dips & Interruptions • EN61000-4-11, 30% 10 ms, Short Circuit Protection • Trip and restart (Hiccup mode) 70% 100 ms, 95% 5000 ms, Temperature • ±0.1% / ˚C Perf Criteria A, B, B Coefficient Safety Approvals • EN60950, UL60950, CSA22.2 No. 950 Remote Sense • HUL175 only. Compensates for 0.5 V drop per cUL, CE Mark on 3.3 V output Remote On/Off • On = Logic High or Open Off = Logic Low or Short Not available on HUL175 Fan Output • 12 V, 300 mA AC-DC AC-DC HUL175 Models and Ratings Output 1 Output 2 Output 3 Output 4 Model Voltage Conv. Max. Voltage Conv. Max. Voltage Conv. Max. Voltage Conv. Max. Number Nom Cooled 18.7 CFM Nom Cooled 18.7 CFM Nom Cooled 18.7 CFM Nom Cooled 18.7 CFM 5.0 V 10.0 A 15.0 A 3.3 V 10.0 A 20.0 A 12.0 V 2.2 A 3.0 A -5.0 V 0.7 A 1.0 A HUL175-40-3 5.0 V 10.0 A 15.0 A 3.3 V 10.0 A 20.0 A 12.0 V 2.2 A 3.0 A -12.0 V 0.7 A 1.0 A HUL175-42-3 5.0 V 10.0 A 15.0 A 3.3 V 10.0 A 20.0 A 24.0 V 1.5 A 2.0 A -12.0 V 0.7 A 1.0 A HUL175-45-3 5.0 V 10.0 A 15.0 A 3.3 V 10.0 A 20.0 A 15.0 V 2.2 A 3.0 A -15.0 V 0.7 A 1.0 A HUL175-46-3 Notes 1. Minimum load is 2 A for V1, 0 A for V2 & V4, and 0.3 A for V3. 2. Total regulation for V1, V2 and V3 = ±5%; V4 = ±3%. Total regulation includes tolerance, line regulation and load regulation. 3. Total combined output power for the 3.3 V and 5.0 V not to exceed 126 W with 18.7 CFM or 70 W with convection cooling. 4. Maximum load continuous output power is 175W with minimum 18.7 CFM forced air cooling or 100 W with convection cooling. 5. Outputs are fully isolated. Mechanical Details All dimensions are in inches (mm) Weight: 1.32 lbs (600 g) approx Tolerance: 0.02 (0.5) max. 0.65 0.2 (16.5) (5.1) B M3 x 0.5 STAND OFF 4 PLACES P2 A M4 x 0.7 NUT FASTENER 8 PLACES 24 3.80 (96.5) P1 G N P3 2.50 L (63.5) P2 Connector 1 Pin Connection A 1 Fan + 2 Fan - B P3 Connector 6.40 (162.5) Pin Connection 1 +3.3 V Sense+ 2, 14 Output 2 4.58 (116.3) 3, 15 Output 2 2.90 (73.7) 0.80 4, 16 Return (20.3) 5, 17 Return 6, 18 Return A A 1.50 7, 19 Output 1 1.25 (38.1) 8, 20 Output 1 (31.8) 9, 21 Output 3 10, 22 Return 5.20 (132.1) 11,23 Output 4 0.24 6.00 (152.4) 12 Power Fail Detect (6.00) 13 +3.3 V Sense- 6.80 (172.7) 24 Return Notes 1. Input connector P1 mates with Molex housing 09-91-0500 and Molex 2478/2578/8818 series crimp terminal. 2. Output connector P3 mates with Molex housing 39-01-2240 and Molex 44476 series crimp terminal. 3. Fan connector P2 mates with JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. Fan output is 12V/160mA. 4. Covered versions are available, add suffix: ‘-C’ to model number for cover only. Dimensions: 3.80” x 6.80” x 1.66” (96.5 x 172.7 x 42.1 mm), ‘-FC’ for fan cover. Dimensions: 3.80” x 6.80” x 2.48” (96.5 x 172.7 x 63.0 mm). 5. Cable harnesses with 11.81” (300 mm) wire available, order part HUL150 LOOM KT. For mating connectors only, order part HUL150 CON KT. 6. Covers are available separately. Order part HUL150 COVER or HUL150 F/COVER for Fan Cover. HUL200 Models and Ratings Output 1 Output 2 Output 3 Output 4 Model Voltage Current Voltage Current Voltage Current Voltage Current (1) Number Nom Nom nom nom Min Max Min Max Min Max Min Max 3.3 V 0.5 A 30.0 A HUL200-10-1†* 5.0 V 0.5 A 40.0 A HUL200-10†* 12.0 V 0.5 A 16.7 A HUL200-12†* 15.0 V 0.5 A 13.3 A HUL200-13†* 24.0 V 0.5 A 8.3 A HUL200-14†* 48.0 V 0.5 A 4.1 A HUL200-18†* +5.0 V 0.5 A 20.0 A +12.0 V 0.0 A 8.0 A HUL200-23†* +5.0 V 0.5 A 20.0 A +15.0 V 0.0 A 6.6 A HUL200-24†* +5.0 V 0.5 A 20.0 A +24.0 V 0.0 A 4.2 A HUL200-25†* +5.0 V 0.5 A 20.0 A +12.0 V 0.0 A 8.0 A F 12.0 V 0.0 A 1.0 A HUL200-31†* +5.0 V 0.5 A 20.0 A +15.0 V 0.0 A 5.0 A F 15.0 V 0.0 A 1.0 A HUL200-32†* +5.0 V 0.5 A 20.0 A +12.0 V 0.0 A 6.0 A -5.0 V 0.0 A 1.0 A F 12.0 V 0.0 A 1.0 A HUL200-40†* +5.0 V 0.5 A 20.0 A +24.0 V 0.0 A 3.0 A -12.0 V 0.0 A 1.0 A F 12.0 V 0.0 A 1.0 A HUL200-45†* +5.0 V 0.5 A 20.0 A +15.0 V 0.0 A 5.0 A -5.0 V 0.0 A 1.0 A F 15.0 V 0.0 A 1.0 A HUL200-46†* +12.0 V 0.5 A 3.0 A +36.0 V 0.0 A 5.0 A +5.0 V 0.0 A 3.0 A -12.0 V 0.0 A 1.0 A HUL200-47 +5.0 V 0.5 A 5.0 A +36.0 V 0.0 A 2.5 A +12.0 V 0.0 A 1.0 A -12.0 V 0.0 A 1.0 A HUL200-47-2 +5.0 V 0.5 A 3.0 A +24.0 V 0.0 A 8.0 A +12.0 V 0.0 A 0.1 A -12.0 V 0.0 A 0.1 A HUL200-47-3 +5.0 V 0.5 A 5.0 A +12.0 V 0.0 A 2.5 A +24.0 V 0.0 A 2.5 A -12.0 V 0.0 A 1.0 A HUL200-47-1 Notes 1. Use part number UL200-XX for product without harmonic correction. e.g.: UL200-10. 4. Total output power for HUL200 single output models is 150 W convection-cooled, 2. Total output power for HUL200-10-1 is 73 W convection-cooled, 100 W with 18.7 200 W with 18.7 CFM forced air cooling. CFM forced air cooling. 5. Total output power for HUL200 multi output models is 100 W convection-cooled, 3. Output #4 is floating except for -47 models. It can be connected externally for 200 W with 18.7 CFM forced air cooling. positive or negative output. 6. Tolerance 5% all outputs, except single output units - tolerance 2%. † Available from Farnell InOne. See pages 236-237 (Farnell series ACL200) *Available from Newark InOne. See page 238 Mechanical Details All dimensions are in inches (mm) Weight: 1.76 lbs (800 g) approx. P2 Connector Tolerance: 0.02 (0.5) max. Pin Single Output Multi Output 1 Output 1 Output 3 1.25 2.5 (63.5) 2 Output 1 Return (31.8) Mounting holes: 3 Output 1 Return L N G A: M4 x 0.7, 8 places 1 A A B B: 6-32, 8 places 4 Output 1 Return B1 B B 5 Output 1 Return A 6 Output 1 Output 1 7 Return Output 1 8 Return Output 1 6.40 9 Return Output 1 (162.5) 10 Return Output 2 5.77 11 Return Output 4 (146.7) 12 Return Output 4 Return 6.80 (172.7) P3 Connector Pin Single Output Multi Output 1 Fan + Multi-output models 2 Return have three separate 2 A pin connectors for Fan, FAN B B 3 Return P2 B P3 Power Good and 4 Power Fail Detect Remote ON/OFF. These A A Pin 1 Pin 1 (6) 1.27 3.80 (96.5) are clearly marked on 5 Remote On/Off (32.3) ±0.3 (7.6) the PCB. 6 Return - 1.50 (38.1) Notes 1. Input connector P1 mates with Molex housing 09-91-0500 and Molex 2478/2578/8818 series crimp terminal. 2. Output connector P2 mates with Molex housing 09-91-1200 and Molex 2478/2578/8818 series crimp terminal. 3. Fan connector P3 mates with JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. 4. Covered versions are available, add suffix: ‘-C’ to model number for cover only. Dimensions: 3.80” x 6.80” x 1.66” (96.5 x 172.7 x 42.1 mm), ‘-FC’ for fan cover. Dimensions: 3.80” x 6.80” x 2.48” (96.5 x 172.7 x 63.0 mm). 5. Covers are available separately. Order part HUL200 COVER or HUL200 F/COVER for Fan Cover. 6. Output is turned off by taking the Remote On/Off pin low (connect to Return). 7. Cable harnesses with 300 mm wire available, order part number HUL200 LOOM-S for single output models, HUL200 LOOM-D for dual output models, HUL200 LOOM-T for triple output models or HUL200 LOOM-Q for quad output models. 8. For mating connectors only, order part HUL200 CON KT. 9. Accessories also available from Farnell InOne†. AC-DC AC-DC HUL300 Models and Ratings Output 1 Output 2 Output 3 Output 4 Model Voltage Current Voltage Current Voltage Current Voltage Current (1) Number Nom Nom nom nom Min Max Min Max Min Max Min Max 5.0 V 0.5 A 60.00 A HUL300-10†* 3.3 V 0.5 A 60.00 A HUL300-10-1†* 12.0 V 0.5 A 25.00 A HUL300-12†* 15.0 V 0.5 A 20.00 A HUL300-13†* 24.0 V 0.5 A 12.50 A HUL300-14†* 48.0 V 0.5 A 6.25 A HUL300-18†* +5.0 V 0.5 A 30.00 A +12.0 V 0.0 A 12.5 A HUL300-23†* +5.0 V 0.5 A 30.00 A +15.0 V 0.0 A 10.0 A HUL300-24†* +5.0 V 0.5 A 30.00 A +24.0 V 0.0 A 6.3 A HUL300-25†* +5.0 V 0.5 A 30.00 A +12.0 V 0.0 A 10.5 A F 12.0 V 0.0 A 2.0 A HUL300-31†* +5.0 V 0.5 A 30.00 A +15.0 V 0.0 A 8.0 A F 15.0 V 0.0 A 2.0 A HUL300-32†* +5.0 V 0.5 A 30.00 A +12.0 V 0.0 A 10.0 A -5.0 V 0.0 A 2.0 A F 12.0 V 0.0 A 2.0 A HUL300-40†* +5.0 V 0.5 A 30.00 A +24.0 V 0.0 A 4.3 A -12.0 V 0.0 A 2.0 A F 12.0 V 0.0 A 2.0 A HUL300-45†* +5.0 V 0.5 A 30.00 A +15.0 V 0.0 A 7.4 A -5.0 V 0.0 A 2.0 A F 15.0 V 0.0 A 2.0 A HUL300-46†* Notes 1. Use part number UL300-XX for product without harmonic correction. e.g. UL300-10. 4. Total output power for all other HUL300 models is 150 W convection-cooled, 300 W 2. Output 4 is floating. It can be connected externally for positive or negative output. with 30 CFM forced air cooling. 3. Total output power for HUL300-12,13,14,18 models is 200 W convection-cooled, 5. Tolerance 5% all outputs, except single output units - tolerance 2%. 300 W with 30 CFM forced air cooling. † Available from Farnell InOne. See pages 236-237 (Farnell series ACL300) *Available from Newark InOne. See page 238 Mechanical Details All dimensions are in inches (mm) Weight: 2.20 lbs (1.0 kg) approx. P2 Connector Tolerance: 0.02 (0.5) max. Pin Single Output Multi Output 1 Output 1 Output 3 0.25 (6.35) 2.50 (63.5) 2 Output 1 Output 1 0.50 P1 3 Output 1 Output 1 (12.7) 1.09 L N G 4 Output 1 Output 1 (27.8) 5 Output 1 Output 1 6 Output 1 Return M4 x 0.7 NUT FASTENER (12 PLACES) 7 Output 1 Return 8 Return Return 8.00 9 Return Return (203.2) 10 Return Return 7.50 (190.5) 11 Return Output 2 7.00 (177.8) 12 Return Output 2 5.81 (147.6) 13 Return Output 4 14 Return Output 4 Return P3 Connector Pin Single Output Multi Output 1 Fan + Return (6) 2 Return DC OK 3 DC OK Return (5) 4 Power Fail Detect Remote On/Off (5) P3 5 Remote On/Off Return PIN 1 P2 6 Return Power Fail Detect 1 14 FAN 0.25 1.00 4.25 (108.0) (6.4) (25.4) 2.00 (50.8) Notes 1. Input connector P1 mates with Molex housing 09-91-0500 and Molex 2478/2578/8818 series crimp terminal. 2. Output connector P2 mates with Molex housing 09-91-1400 and Molex 2478/2578/8818 series crimp terminal. 3. Covered versions are available, add suffix: ‘-C’ to model number for cover only. Dimensions: 4.25” x 8.00” x 2.16” (108.0 x 203.2 x 54.8 mm) ‘-FC’ for fan cover. Dimensions: 4.25” x 8.00” x 3.00” (108.0 x 203.2 x 75.7 mm). 4. Fan connector mates with JST housing XHP-2 and JST SXH-002T-P0.6 crimp terminals. Multiple outputs only. 5. Output is turned off by taking the Remote On/Off pin low (connect to Return). 6. DC OK is a open collector output. Low = normal operation. 7. Cable harnesses with 300 mm wire available, order part number HUL300 LOOM-S for single output models, HUL300 LOOM-D for dual output models, HUL300 LOOM-T for triple output models or HUL300 LOOM-Q for quad output models. For mating connectors only, order part HUL300 CON KT. 8. Covers are available separately. Order part HUL300 COVER or HUL300 F/COVER for Fan Cover. 9. Accessories also available from Farnell InOne†. 08/04/05