TM wAVETRONIX Click! 301 Serial to Ethernet Converter The Click!™ 301 converts half-duplex RS-232 & RS-485 communication to Ethernet and vice versa. This device, tested to work over a –34°C to 74°C temperature range, can be used as part of a traffic cabinet to communicate between devices via Ethernet connections. Features ■ ■ Converts half-duplex serial to Ether- Supports Click! Supervisor for easy net and vice-versa setup and configuration on your ■ Multiple communication ports, includ- computer ■ ing RS-232, RS-485 and Ethernet Allows auto-reset of inactive sockets ■ ■ Auto-configures baud rates Applications include: ■ à Can be configured over either Ether- Controller closed loop Ethernet à net or serial interfaces Sensor to Ethernet ■ ■ Snaps onto DIN rail for quick and easy Conformal coated ■ installation Available in DIN rail, rack or controller ■ Three LEDs on faceplate of device card modules allow for easy monitoring of device functionality WX-500-0109 1 Click! 301 Technical Specifications Ordering Information Physical ■ Weight: 0.2 lbs. (0.1 kg) Part Number — WX-CLK-301 ■ Physical dimensions: 4.5 in. × 4 in. × 0.9 in. (11.4 cm x 10.2 cm x 2.3 cm) ■ Ambient operating temperature: -29°F to 165°F (-34°C to 74°C) ■ Humidity: up to 95% RH Wavetronix 78 East 1700 South Mounting Provo, UT 84606 ■ DIN rail–mountable Phone: 801-734-7200 Fax: 801-734-7201 Power ■ Power supply voltage: 10 to 30 VDC Email: sales@wavetronix.com ■ Uses less than 1 W of average power at 24 VDC Website: www.wavetronix.com Connections ■ Device has the following connection points: à Runs on both a Pocket PC and a Windows desktop or à Power: 5-position connector for connecting from the T-bus laptop PC (Windows 2000 and newer) à RS-232: Through a DB-9 connector à Configures serial communication settings including the à RS-485: 5-position connector for connecting from the T- serial baud rates bus as well as one pluggable screw terminal à Can remotely and directly upgrade the device firmware to à Ethernet: one RJ-45 jack on the front of the device add new features to the device à Allows users to save a configuration to a file, and to open Communication existing files and save to a device, allowing a common con- ■ Converts RS-232 to RS-485 and vice versa figuration to be easily programmed into many devices ■ Communicates serial to Ethernet and vice versa à Has customizable drivers that are stored as XML files that describe the graphical user interface for that driver Baud Rates ■ Supports the following baud rates: Remote Upgradeability à 1200 bps ■ Flash memory can be remotely upgraded to add functionality à 2400 bps to the firmware when new features have been developed to à 4800 bps improve the performance of the installation à 9600 bps à 19200 bps NEMA TS2-1998 Testing à 38400 bps ■ Complies with the applicable standards stated in the NEMA à 57600 bps TS2-1998 Standard à 115200 bps ■ Test results available for each of the following tests: à Shock pulses of 10g, 11 ms half sine wave Configuration Features à Vibration of .5 Grms up to 30 Hz ■ Push-button has the following functions: à 300 V positive/negative pulses applied at one pulse per à Autobauds device to a SmartSensor or other serial device second at minimum and maximum DC supply voltage à Resets device to factory defaults à Stored at -49ºF (-45ºC) for 24 hours ■ LEDs: à Stored at 185ºF (85ºC) for 24 hours à Red LED illuminates when device has power à Operation at -29.2ºF (-34ºC) and 10.8 VDC à Yellow LED (TD) illuminates when data is transmitted à Operation at -29.2ºF (-34ºC) and 26.5 VDC à Green LED (RD) illuminates when data is received à Operation at 165.2ºF (74ºC) and 26.5 VDC à Operation at 165.2ºF (74ºC) and 10.8 VDC Pocket PC & PC Configuration Software ■ Comes with Click! Supervisor, configuration software with the Testing following features: ■ Tested by manufacturer before shipping 2 www.wavetronix.com TM wAVETRONIX Click! 301 Extended Support ■ Extended support options are available from Wavetronix; con- tact a Wavetronix representative for more information Warranty ■ One-year warranty against material and workmanship defect 3 Click! 301 Click! 301 Bid Specification 1.0 General. This item shall govern the purchase and instal- 6.4 Ethernet. The SECM shall feature an RJ-45 jack for lation of a hardened RS-485 and RS-232 serial to Ethernet con- Ethernet. verter module (SECM) equivalent to the Wavetronix Click!™ 7.0 Communication. The SECM shall have the following com- 301 that is used to convert two-wire RS-485 communications munication capabilities: and RS-232 to IP-addressable Ethernet standard. Test results and other documentation demonstrating performance and 7.1 Serial Protocol Conversion. The SECM shall allow capabilities shall be provided. communications with any serial device that has a serial connection by converting 2-wire half-duplex RS-485 com- 2.0 Product Description. The SECM shall be a converter munication to half-duplex RS-232 communication, and module for use with radar vehicle sensing devices (RVSD) vice versa. equivalent to the Wavetronix SmartSensor™. The SECM shall be capable of converting two-wire half-duplex RS-485 com- 7.2 Ethernet. The SECM shall convert RS-232 and RS-485 munication and RS-232 communication to IP-addressable protocol to Ethernet, allowing communication with any Ethernet protocol and vise versa. All serial ports shall pass device connected to the SECM via an Ethernet network. data on one port to all other ports. Any data coming to or from the Ethernet port shall simultaneously be sent to all RS-485 8.0 Baud Rates. The SECM shall support baud rates of 1200 and RS-232 ports. bps, 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps and 115200 bps. 3.0 Physical. The SECM shall not exceed 0.2 lbs. (0.1 kg) in weight. 9.0 Configuration Features. The SECM shall not exceed 4.5 in. × 4 in. × 0.9 in. (11.4 cm x 9.1 Push-button. The front of the SECM shall include 10.2 cm x 2.3 cm) in its physical dimensions. a push-button that causes the SECM to autobaud to a SmartSensor or other serial device. It shall also be able to The SECM shall operate within a temperature range of -29°F to reset the SECM to factory defaults. 165°F (-34°C to 74°C). 9.2 LEDs. The front of the SECM shall include a red LED The SECM shall operate in humidity up to 95% RH. for power and green and yellow LEDs, which shall illumi- nate when corresponding data is successfully transmitted 4.0 Mounting. The SECM shall mount to a DIN rail with hot- or received. swappable power and communication buses for quick installa- tion and replacement. 10.0 Pocket PC & PC Configuration Software. The SECM shall be provided with configuration software that: 5.0 Power. The SECM shall have a power supply voltage of 10 to 30 VDC. ● Runs on both a Pocket PC and a Windows desktop or laptop PC (Windows 2000 and newer) The SECM shall operate using less than 1 W of average power ● Configures serial communication settings including the se- at 24 VDC. rial baud rates ● Can remotely and directly upgrade the SECM firmware to 6.0 Connections. The SECM shall include the following con- add new features to the SECM nections for power and communication: ● Allows users to save a configuration to a file, and to open existing files and save to a device, allowing a common con- 6.1 Power. The SECM shall include a 5-position connector, figuration to be easily programmed into many devices with two contact points reserved for connecting power ● Has customizable drivers that are stored as XML files that through the bus. describe the graphical user interface for that driver 6.2 RS-232. The SECM shall feature a DB-9 connector for 11.0 Upgradeability. The SECM shall have flash memory that RS-232 communication. can be remotely upgraded to add functionality to the firm- 6.3 RS-485. The SECM shall feature a pluggable screw ter- ware when new features have been developed to improve the minal for RS-485 communication. The 5-position connec- performance of the installation. tor shall have three contact points reserved for connecting 12.0 NEMA TS2-1998 Testing. The SECM shall comply RS-485 through the bus. with the applicable standards stated in the NEMA TS2-1998 4 www.wavetronix.com TM wAVETRONIX Click! 301 Standard. Test results shall be made available for each of the following tests: ● Shock pulses of 10g, 11 ms half sine wave ● Vibration of 0.5 Grms up to 30 Hz ● 300 V positive/negative pulses applied at one pulse per second at minimum and maximum DC supply voltage ● Cold temperature storage at -49°F (-45°C) for 24 hours ● High temperature storage at 185°F (85°C) for 24 hours ● Low temp, low DC supply voltage at -29.2°F (-34°C) and 10.8 VDC ● Low temp, high DC supply voltage at -29.2°F (-34°C) and 26.5 VDC ● High temp, high DC supply voltage at 165.2°F (74°C) and 26.5 VDC ● High temp, low DC supply voltage at 165.2°F (74°C) and 10.8 VDC 13.0 Testing. Before shipping, each SECM shall have passed a manufacturer’s test. 14.0 Extended Support. Extended support options shall be available. Contact the manufacturer’s representative for more information. 15.0 Warranty. The SECM shall be warranted to be free from material and workmanship defects for a period of one year from date of shipment. 5