VMICPCI-7808 ® ® ® Pentium /Celeron M Universal CompactPCI Single Board Computer ® • Intel ’s Pentium/Celeron M processors up to 1.8 GHz (see ordering options) • Up to 2 GB DDR SDRAM with ECC using one SODIMM • Dual Ethernet controller supporting 10/100/1000BaseTX interface • Serial ATA support Photo Not Available • Two high performance 16550-compatible serial ports ® • Fully supports PICMG 2.16 • Two PMC expansion sites (one 64-bit/66MHz, the other 32-bit/33 MHz) ® • 64-bit/66 MHz CompactPCI bus Interface • IPMI support PICMIG Rev. 2.9 • USB 2.0 support (one standard USB connector on the front panel and two routed to the backplane rear I/O ) Ordering Options ® • Operating system support for Windows 2000/Windows XP, ® ® Nov. 15, 2004 800-657808-000 A B C D E F Linux , QNX and VxWorks VMICPCI-7808 – 0 0 0 0 Functional Characteristics A = Processor 0 = Reserved Microprocessor: The VMICPCI-7808 is based on the Pentium M 1 = 1.3 GHz Celeron M Processor 2 = Reserved processor family. The enhanced 1.6 GHz Pentium M processor has 1 MB 3 = 1.4 GHz Pentium M Processor 4 = 1.6 GHz Pentium M Processor of L2 cache, while the 1.4 GHz and the 1.8 GHz Pentium M processors 5 = 1.8 GHz Pentium M Processor have 2 MB of L2 cache. The Celeron M processor has 512 KB of L2 B = DDR SDRAM Memory 0 = 256 MB cache. The Pentium/Celeron M processor family offers thermal 1 = 512 MB characteristics that are well suited for embedded systems operating 2 = 1 GB 3 = 2 GB over a wide range of temperatures. C through F = 0 (Options reserved for future use.) CompactPCI Rear Transition Utility Board DRAM Memory: The VMICPCI-7808 accepts one 200-pin DDR VMIACC-0591 SODIMM with ECC memory module for configurations of up to 2GB (see The VMIACC-0591 installs in the rear transition area of the CompactPCI backplane and provides access to CompactFlash on primary IDE, IDE hard disk ordering options for available memory sizes). drive, floppy, COM 2, two USB ports, video and keyboard/mouse functions. The VMIACC-0591 is sold separately. BIOS: The VMICPCI-7808 System BIOS and video BIOS are provided in For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859 reprogrammable memory. Email: info.embeddedsystems@gefanuc.com Web Address: www.gefanuc.com/embedded Video Graphic Controller: High-resolution graphics and multimedia- Copyright © 2004 by VMIC Specifications subject to change without notice. quality video are supported on the VMICPCI-7808 by an internal graphics controller. A fully functional, integrated 2D/3D graphics accelerator provides pixel processing and rendering, with display resolutions of up to 1600 x 1200 supported. The video output is provided through the CompactPCI connector. Support is provided for both analog and LVDS digital video using the VMIACC-0591 rear transition board. NOTE: Standard video BIOS support for LVDS is for an 800 x 600 panel only. If the VMIACC-0591 rear transition board is not used, then the video should be disabled via CMOS setup. GE Fanuc Automation Americas, Inc. 12090 South Memorial Parkway, Huntsville, Alabama 35803-3308 1 VMICPCI-7808 backplane rear I/O for use with the optional VMIACC-0591 Rear IDE Interface: The VMICPCI-7808 provides an IDE interface for hard Transition board. disk drive and CompactFlash support, using the optional VMIACC-0591 Rear Transition board. The IDE interface allows support of several types Serial Ports: The VMICPCI-7808 provides two 16550-compatible serial of data transfers: Programmed I/O (PIO), 8237 style DMA, Ultra ATA/33, ports. Each serial port has an independent 16-byte FIFO supporting baud Ultra ATA/66 and Ultra ATA/100. When the CompactFlash in installed rates up to 115 Kbaud. Connection for one serial port (COM1) is only one other IDE device can be installed. provided by an RJ45 connector located on the front panel, the other serial port (COM2) is available via the CompactPCI backplane rear I/O, NOTE: Ultra DMA IDE modes require a high performance 80-conductor using the optional VMIACC-0591 Rear Transition board with a standard cable. DB-9 connector. Write Protection: The VMICPCI-7808 has the ability to write protect a PMC Expansion Sites: The VMICPCI-7808 provides two IEEE 1386.1 CompactFlash when using the optional VMIACC-0591 Rear Transition PCI mezzanine card (PMC) expansion sites. This expansion capability board equipped with a CompactFlash (boards equipped with the allows the addition of peripherals offered for PMC applications. One SanDisk Industrial type CompactFlash). Write protection provides PMC site is 3.3 V 64-bit, 66 MHz, while the second site is 5.0 V 32-bit, security features that allow the user to control the ability to write to the 33 MHz. CompactFlash through a control register. Configuration of this feature requires a user selectable 40-bit security key for subsequent accesses Keyboard and Mouse Ports: The VMICPCI-7808 supports a PS/2 type to the device. keyboard and mouse connection with signals routed to the CompactPCI rear I/O using the optional VMIACC-0591 backplane adapter. Ethernet Controller: The VMICPCI-7808 provides dual channels for 10/100/1000Mbit Ethernet using the Intel 82546EB Dual Ethernet Hardware Reset: A hardware reset switch is accessible from the front controller. A front panel RJ45 connector is provided with two network panel. status indicators, supporting PICMG 2.16 Rev 1.0. The front panel Watchdog Timer: The VMICPCI-7808 provides a software- Ethernet interface can be switched from front to rear using the CMOS programmable watchdog timer. The watchdog timer is enabled under LAN selections. The other channel is PICMG 2.16 Rev 1.0 compatable software control. Once the timer is enabled, software must access the and only available at the CompactPCI rear I/O, using the optional timer within the specified time period, or the output of the watchdog VMIACC-0591 Rear transition board. Front panel status indicators are timer will either interrupt or reset the unit. The reset or interrupt available for the channel routed to the rear I/O. operation is programmable. NOTE: When the front panel LAN interface is switched to the rear, the Annunciators: Indicators for the primary IDE interface activity, board VMIACC-0591 Rear Transition board is required. status, power good and a blue LED for hot swap are provided on the Serial ATA: The VMICPCI-7808 provides a serial ATA interface via the front panel. In addition, two indicators for the Ethernet adapter link and CompactPCI backplane connector using the VMIACC-0591 rear activity are located on the RJ45 network connector. Two other transition board. indicators are provided on the front panel for the second Ethernet port link and activity, routed from the rear I/O. Remote Ethernet Booting: The VMICPCI-7808 utilizes an Expansion ROM BIOS, which enables processor booting from a network server. The Thermal Management: The VMICPCI-7808 utilizes a passive heat sink facility supports PXE and a variety of network boot protocols including that relies on forced air cooling within the equipment rack at the BOOTP and DHCP (TCP/IP). specified flow rate. Please refer to the environmental specifications for more information. USB Ports: The VMICPCI-7808 provides three high-speed universal serial bus (USB 2.0) ports. Connection for one USB port is provided on CompactPCI Bus Bridge: The VMICPCI-7808 is a universal the front panel. The two other ports are available on the CompactPCI CompactPCI single board computer (SBC) supporting applications as a system slot controller or a peripheral slot controller. The GE Fanuc Automation Americas, Inc. 12090 South Memorial Parkway, Huntsville, Alabama 35803-3308 2 VMICPCI-7808 PCI-to-PCI bridge interface to the CompactPCI bus is automatically +3.3 VDC (+5, -3 percent), 1.5 A (typical), 2.0 A maximum configured to operate as either a transparent or non-transparent bridge. +12.0 VDC (+5, -3 percent), 50 mA maximum This implementation is fully compliant with PICMG 2.0 Rev 3.0, -12 VDC (+5, -3 percent), 50 mA maximum PICMG 2.1 Rev 2.0, and PCI-to-PCI Bridge Architecture Rev 1.1. Celeron M 1.3 GHz and the Pentium M Processors 1.6 GHz and IPMI: The VMICPCI-7808 provides PICMG 2.9 Rev 1.5 IPMI support via 1.8 GHz: the Zircon PM Peripheral Management Controller. +5 VDC (+5, -3 percent), (typical), maximum +3.3 VDC (+5, -3 percent), (typical), maximum High Availability Hot Swap: The VMICPCI-7808 complies with +12.0 VDC (+5, -3 percent), maximum PICMG 2.1 Rev 2.0 standard for CompactPCI hot swap. The -12 VDC (+5, -3 percent), maximum VMICPCI-7808 complies with the high availability provisions of this standard. The processor may be removed and replaced while the system Airflow: Forced air cooling required, 400 LFM minimum, measured at is operational. Processing can automatically be switched to a back-up the top (outlet) of the unit SBC that was previously installed in the system. Altitude: CMOS Battery: The VMICPCI-7808 uses a holder that permits field Operating, 0 – 10,000 ft (3,000 m) replacement of the CMOS battery. A header and jumper allows the Storage, 0 – 40,000 ft (12,000 m) battery to be disconnected from the circuitry for long-term storage. Operating Temperature: 1.3 GHz Celeron M Processor = -0°C to 50°C max (.13u uFC-PGA) Back Panel Configuration: The VMICPCI-7808 provides support for 1.4 GHz Pentium M Processor = -0°C to 65°C max (90nm uFC-BGA) several peripherals using the CompactPCI backplane rear I/O connectors. These signals are routed to the CompactPCI J3 and J5 1.6 GHz Pentium M Processor = -0°C to 50°C max (.13u uFC-PGA) connectors. This permits connection of the external IDE hard disk drive, 1.8 GHz Pentium M Processor = -0°C to 55°C max (90nm uFC-PGA) CompactFlash, PMC I/O, floppy drive, two USB, two SATA, video, and Storage: -40 °C to +85 °C keyboard/mouse via the VMIACC-0591 Rear Transition board. NOTE: The Pentium M processor will throttle when its junction Connection to these signals is provided to facilitate application temperature is between 90 °C and 100 °C. If application cannot take development. throttling of the CPU, then the thermal profile of the system must be NOTE: If the VMICPCI-7808 is not used with the VMIACC-0591 Rear verified to keep the CPU junction temperature less than 90 °C. Transition board, the user is responsible for either terminating video, Humidity: SATA and USB or for disabling these features in the CMOS setup. Operating, Relative Humidity 5% to 95%, noncondensing Operating System and Software Support Storage, Relative Humidity 5% to 95%, noncondensing The VMICPCI-7808 supports a variety of operating systems including Vibration: 6 Gs RMS (20 - 2000 Hz) random, .0185 G2 per Hz spectrum ® Microsoft Windows 2000, Windows XP, Linux, QNX and VxWorks. Shock: 10 Gs, 16 ms half sine, 6 axis, 10 pulses each Physical/Environmental Specifications MTBF: Total FiT x QTY: 4992.766332 Dimensions: 6U (4HP) single slot Eurocard form factor MTBF (hours): 200,289.76593 Height 9.2 in. (233.4 mm) Trademarks Depth 6.3 in. (160 mm) Intel, Pentium and Celeron are registered trademarks of Intel Thickness 0.8 in. (20.3 mm) Corporation. Microsoft and Windows are registered trademarks of Power Requirements: (Does not include PMC power.) Microsoft Corporation. CompactPCI and PICMG are registered trademarks of PCI Industrial Computer Manufacturer’s Group. Other Pentium M Processor (1.4 GHz): registered trademarks are the property of their respective owners. +5 VDC (+5, -3 percent), 4.5 A (typical), 6.75 A maximum GE Fanuc Automation Americas, Inc. 12090 South Memorial Parkway, Huntsville, Alabama 35803-3308 3 VMICPCI-7808 PMC I/O Intel Pentium M or Celeron M USB (x2) J5 Processor up to 1.8 GHz SATA (x2) Processor IDE 64/66 System bus PMC DDR Site SDRAM SODIMM w/ECC Up to 2.0 Gbyte Intel 855GME SVGA Graphics and Memory System Memory bus Controller Hub (GMCH) Digital/LVDS Video 32/33 PMC Site Intel 6300ESB I/O Controller Hub (ICH) J3 IPMI 64/66 MHz PCI Bus LPC/FWH bus BIOS Intel 82546EB Switch Dual Ethernet 10/100/1000 Mbit (PICMG 2.16) Controller J2 10/100/1000 Mbit (PICMG 2.16) 10/100/1000 Ethernet Rear I/O Ethernet COM 2 Indicators USB 2.0 Super I/O Floppy COM 1 J1 Reset Switch Keyboard / Mouse and Status Universal Indicators PCI-to-PCI Bridge Figure 1. VMICPCI-7808 Functional Block Diagram GE Fanuc Embedded Systems Information Centers Additional Resources USA and the Americas: Europe, Middle East and Africa: For more information, please visit the Huntsville, AL 1 800 322-3616 Edinburgh, UK 44 (131) 561-3520 GE Fanuc Embedded Systems web site at: 1 (256) 880-0444 Paris, France 33 (1) 4324 6007 www.gefanuc.com/embedded Ventura, CA 1 (805) 650-2111 4