TEXAS MICRO SLE/1.0B
Specifications
BATTERY
Built-in lithium battery for ten years of data retention for CMOS memory.
BIOS (FLASH)
AMI 7.0 BIOS with built-in advanced CMOS setup for system parameters, peripheral management for configuring on-board peripherals, PCI-to-PCI bridge support, and PCI interrupt steering. Supports flash devices for BIOS upgrading via floppy interface. Custom BIOSs available.
BUS SPEED
ISA 8MHz
CACHE MEMORY (L2)
The Pentium III processor includes an integrated on-die, 256K or 512K 8-way set associative level two (L2) cache with a 256-bit wide bus. The processor also includes a 16K level one (L1) instruction cache and 16K L1 data cache. These cache arrays run at the full speed of the processor core.
CHIPSET
ServerWorks ServerSet III LE chip set supports higher Front Side Bus bandwidth at 133MHz, with full support for ECC on the memory bus. Supports single-bit error correction, with multiple-bit error detection.
DATA PATH
Data/Memory 64-bit
ENHANCED BI-DIRECTIONAL PARALLEL INTERFACE
Compatible with PC/AT bi-directional parallel port and supports EPP and ECP modes. The ECP mode is IEEE 1284 compliant. Parallel port has BIOS selectable addressing.
ERROR CHECKING AND CORRECTION
The memory interface supports ECC modes via BIOS setting for multiple-bit error detection and single-bit error correction.
FLOPPY DRIVE INTERFACE
Supports up to two floppy disk drives in combinations of 360K to 2.88MB.
FRONT SIDE BUS
The ServerWorks ServerSet III LE supports speeds of 133MHz. The Front Side Bus provides a path for transferring data between main memory/chip set and the microprocessors.
Humidity
5% to 90% non-condensing
ISA BUS
Provides ISA Bus interface to backplanes for legacy ISA slots.
KEYBOARD AND PS/2 MOUSE INTERFACES
The keyboard and PS/2 mouse interfaces are combined into one connector. These interfaces are protected by self-resetting fuses and are accessible via a Y cable or off-board cabling.
MEAN TIME BETWEEN FAILURES (MTBF)
148,000 POH (Power-On Hours) at 40° C., per Bellcore.
Operating Temperature
0° - 60° C. for 866MHz and below 0° - 50° C. for 933MHz
PCI 10/100BASE-T ETHERNET INTERFACE (DUAL)
The dual PCI Ethernet interfaces (Intel 82559) support 10/100Base-T via RJ-45 connectors on the board's I/O bracket. The interfaces are compliant with IEEE 802.3 and PCI Local Bus 2.1 Specifications. Link status and activity LEDs are on the I/O bracket. Software drivers are available for most popular operating systems..
PCI EIDE ULTRA DMA/33 INTERFACE (DUAL)
Dual high performance PCI Bus Master EIDE interfaces are capable of supporting up to four IDE disk drives in a master/slave configuration. Supports Ultra DMA/33 with synchronous DMA mode transfers up to 33MB per second.
PCI LOCAL BUS INTERFACE
The SLE provides on-board Primary and Secondary PCI Bus interfaces. Both Primary and Secondary bus interfaces provide a sixteen deep I/O cache and a four deep request queue for PCI to Memory cycles.
PCI ULTRA3 SCSI INTERFACE
The Ultra3 SCSI interface is a PCI Bus Master device using the QLogic ISP10160A SCSI controller, which supports Ultra3 SCSI maximum throughput of 160MB per second. Ultra 160 drives are supported. Enable/disable active termination is provided with terminator voltage protected by self-resetting fuses. Software drivers are available for most popular operating systems.
POWER FAIL DETECTION
Issues a hardware reset when on-board voltage drops below 4.75 volts.
POWER REQUIREMENTS
+5V Typical
Processor
Intel Pentium III
PROCESSOR (DUAL)
Intel Pentium III microprocessors (FC-PGA) at 600EBMHz - 1.26GHz.
SDRAM MEMORY
The SDRAM interface consists of two dual in-line memory module (DIMM) sockets and supports auto detection of memory up to 2GB of Synchronous DRAM (SDRAM) memory. The DIMM memory is PC-133 compliant for a 133MHz Front Side Bus, which means that it complies with IBM's PC133 SDRAM Registered DIMM Design specification. Uses industry standard 72-bit (ECC) wide gold finger DIMM DRAM in two 168-pin DIMM sockets.
SERIAL INTERFACE
Two high-speed FIFO (16C550) serial ports with independently programmable baud rates. Each serial port has BIOS selectable addressing.
Storage Temperature
-40° to 70° C.
SUPER VGA INTERFACE
The Intel 69030 video interface has 4MB of on-chip memory and supports pixel resolutions up to 1280 x 1024 x True Color non-interlaced. Software drivers are available for most popular operating systems.
SYMMETRIC MULTIPROCESSING (SMP)
The dual Pentium III processor-based design allows the operating system to assign tasks on demand to the next available processor. SMP uses applications which are divided into threads which can run concurrently on any available processor.
SYSTEM HARDWARE MONITOR
Provides monitoring of system voltages, temperature and fan speed.
UNIVERSAL SERIAL BUS (USB)
Supports two USB 1.0 ports for serial transfers at 12 or 1.5Mbit/sec. The Universal Serial Bus is an interface allowing for connectivity to many standard PC peripherals via an external port.
WATCHDOG TIMER
The software controlled watchdog timer monitors system activity and generates a reset pulse in the event of a time-out.
Features
- 133MHz Front Side Bus
- 512K L2 cache
- 64-bit/66MHz PCI Local Bus
- Dual Ethernet
- Dual Intel Pentium III Processors
- Processing speeds up to 1.26GHz
- SDRAM Memory
- Ultra3 SCSI
Datasheet
Extracted Text
PRODUCT DATA SHEET SLE SINGLE BOARD COMPUTER System Hardware Monitor SDRAM Memory up to 2GB Ultra3 SCSI Interface Dual PCI EIDE Ultra DMA/33 Universal Serial Bus Serial Ports Floppy Drive Interface (16C550) Enhanced Bi-Directional Parallel Interface PS/2 Mouse and Keyboard Interface SVGA Interface Dual PCI 10/100Base-T Ethernet Interfaces ® ® PICMG Connector Dual Pentium III Processors ISA Bus AMI Flash BIOS ® ® Featuring dual Intel Pentium III processors and PCI ULTRA3 SCSI INTERFACE: BIOS (FLASH): sophisticated SMP for multi-threaded applications The Ultra3 SCSI interface is a PCI Bus Master device using the AMIBIOS 7.0 with built-in advanced CMOS setup for system and enhanced throughput, the SLE handles your QLogic ISP10160A SCSI controller, which supports Ultra3 SCSI parameters, peripheral management for configuring on-board current needs and tough applications. The SLE maximum throughput of 160MB per second. Ultra160 drives are peripherals, PCI-to-PCI bridge support, and PCI interrupt steering. also features SDRAM memory, giving you a supported. Enable/disable active termination is provided with Supports flash devices for BIOS upgrading via floppy interface. terminator voltage protected by self-resetting fuses. Software Custom BIOSs available. cost-effective, proven technology. Additionally, drivers are available for most popular operating systems. the SLE has dual Ethernet interfaces and Ultra3 PCI LOCAL BUS INTERFACE: SCSI. The SLE supports a 133MHz Front Side Bus PCI 10/100BASE-T ETHERNET INTERFACES (DUAL): The SLE provides on-board Primary and Secondary PCI Bus interfaces. (FSB) and a 64-bit/66MHz PCI Local Bus. With The dual PCI Ethernet interfaces (Intel 82559) support Both the Primary and Secondary PCI Bus interfaces provide a all of these features on board, you have more 10/100Base-T via RJ-45 connectors on the board’s I/O bracket. The sixteen deep I/O cache and a four deep request queue for PCI available slots to handle today’s requirements interfaces are compliant with IEEE 802.3 and PCI Local Bus 2.1 to Memory cycles. and build for the future. Specifications. Link status and activity LEDs are on the I/O bracket. Primary PCI Interface: The Primary PCI interface is 32 bits Software drivers are available for most popular operating systems. wide, runs at 33MHz and supports on-board SCSI, video and PROCESSOR: PCI EIDE ULTRA DMA/33 INTERFACES (DUAL): dual Ethernet interfaces. ® ® Intel Pentium III processors - FC-PGA/FC-PGA2 Dual high performance PCI Bus Master EIDE interfaces are capable of Secondary PCI Interface: The Secondary PCI interface is Speeds: 733MHz - 1.26GHz supporting two IDE disk drives each in a master/slave configuration. 64 bits wide and runs at 33/66MHz. The interface is routed off ® Supports Ultra DMA/33 with synchronous DMA mode transfers up board to drive PCMIG compliant PCI/ISA backplanes. CHIPSET: to 33MB per second. SYMMETRIC MULTIPROCESSING (SMP): ™ ServerWorks ServerSet III LE chipset supports a Front Side Bus DRAM MEMORY: bandwidth of 133MHz, with full support for ECC on the memory bus. The dual Pentium III processor-based design allows the operating Supports single-bit error correction, with multiple-bit error detection. The DRAM interface consists of two dual in-line memory module system to assign tasks on demand to the next available processor. (DIMM) sockets and supports auto detection of memory up to SMP uses applications which are divided into threads which can CACHE MEMORY (L2): 2GB of Synchronous DRAM (SDRAM) memory. The DIMM memory run concurrently on any available processor. is PC-133 compliant, which means that it complies with IBM’s The Pentium III processor includes an integrated on-die, 256K or PC133 SDRAM Registered DIMM Design specification. Uses 512K 8-way set associative level two (L2) cache with a 256-bit industry standard 72-bit wide (ECC) gold finger DIMM modules wide bus. The processor also includes a 16K level one (L1) in two 168-pin DIMM sockets. instruction cache and 16K L1 data cache. These cache arrays run at the full speed of the processor core. BUS SPEEDS: FRONT SIDE BUS: ISA - 16-bit/8MHz PCI - 32-bit/33MHz The ServerWorks ServerSet III LE supports speeds of 133MHz. - 64-bit/33MHz The Front Side Bus provides a path for transferring data between - 64-bit/66MHz main memory/chipset and the microprocessors. System/FSB - 133MHz Dependable, always. TRENTON Technology Inc. • 2350 Centennial Drive, Gainesville, Georgia 30504 • Sales: (800) 875-6031 • Phone: (770) 287-3100 • Fax: (770) 287-3150 E-mail: Sales@TrentonProcessors.com • Web: www.TrentonProcessors.com PRODUCT DATA SHEET ® ® Pentium III Pentium III Processor Processor FC-PGA 370 FC-PGA 370 AGTL + Host Bus DIMM Module Sockets 64-bit/66 MHz PCI Bus (2) To ™ ServerSet III LE Backplane PC-133 NorthBridge On-Board 32-bit/33 MHz PCI Bus DRAM ServerWorks NB6635 External Hardware Monitor Monitor Port SMBus PCI SMBus Video SCSI Ethernet Ethernet Mouse Port Super Controller Controller Controller Controller LAN I/O ™ Intel QLogic Intel Intel ServerSet III LE Keyboard IDE 69030 ISP10160A 82559 82559 SouthBridge Port Primary Ultra3 10/100 10/100 LAN Serial IDE Port 1 Secondary Super VGA SCSI Monitor Serial USB 0 ServerWorks Port 2 USB 1 IB6566 To ISA Parallel Backplane ISA Bus Port Flash ROM SMC Floppy 37B782 Port BIOS SUPER VGA INTERFACE: SLE APPLICATION CONSIDERATIONS: AGENCY APPROVALS: The Intel 69030 video interface has 4MB of on-chip memory Power Requirements: • Designed for UL1950, CAN/CSA C22.22 No. 950-95, and supports up to 1280 x 1024 pixel resolutions. Software +5V Typical EN610000-6-2: 1999; EN55022: 1998, Class B EN61000-3-2: drivers are available for most popular operating systems. 14.95 Amps 1.26GHz 1995/A2; 1998; EN6100-3-3; 1995 14.02 Amps 1.0GHz Rev. L-07 and later ADDITIONAL SLE FEATURES: ORDERING INFORMATION: 13.6 Amps 1.0GHz Rev. K-06 and earlier 11.4 Amps 866MHz System Hardware Monitor: 10.5 Amps 733MHz Model Name: SLE •Provides monitoring of system voltages, temperature and Model # CPU Speed fan speed. +12V @ 500 mAmps for Rev. L-07 and later 5891-602-xM 1.26GHz +12V @ 600 mAmps for Rev. K-06 and earlier 5891-407-xM 1.0GHz – Watchdog Timer: 12V @ <100 mAmps 5891-405-xM 866MHz • The software controlled watchdog timer monitors system 5891-403-xM 733MHz Temperature/Environment: activity and generates a reset pulse in the event of a timeout. Operating Temperature: 0° to 60° C. for 866MHz and below (xM = Memory) 0° to 50° C. for 933MHz I/O Features: Intel and Pentium are registered trademarks of Intel Corporation. All other product 0° to 45° C. for 1.0GHz •Two high-speed serial ports names are trademarks of their respective owners. 0° to 50° C. for 1.26GHz • Enhanced bi-directional parallel interface • Dual Universal Serial Bus (USB, Rev. 1.1) – Storage Temperature: 40° to 70° C. Copyright ©2002 by TRENTON Technology Inc. All rights reserved. • PS/2 mouse/keyboard interface Humidity: 5% to 90% non-condensing • Floppy drive interface Mechanical: MEAN TIME BETWEEN FAILURES (MTBF): A low-profile (1.44” height) active cooling system is used on the SLE to insure reliable processor operation at elevated temperatures. 148,000 POH (Power-On-Hours) at 40° C., per Bellcore Overall dimensions of the SLE, including the active cooling system, are 13.3” L (338mm) x 4.8” H (121.9mm) x 1.57” W (39.9mm). STANDARDS: • IEEE P996, Personal Computer Bus Standard Dependable, always. • PCI Local Bus Specification 2.1 ® • PICMG 1.0 Specification TRENTON Technology Inc. • 2350 Centennial Drive, Gainesville, Georgia 30504 • Sales: (800) 875-6031 • Phone: (770) 287-3100 • Fax: (770) 287-3150 E-mail: Sales@TrentonProcessors.com • Web: www.TrentonProcessors.com 8415891 10152 3.0 ADDR DATA CNTL ADDR DATA CNTL ADDR DATA CNTL
Frequently asked questions
What makes Elite.Parts unique?

What kind of warranty will the SLE/1.0B have?

Which carriers does Elite.Parts work with?

Will Elite.Parts sell to me even though I live outside the USA?

I have a preferred payment method. Will Elite.Parts accept it?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
Related Products

Trenton SLE S5891-XXX CPU Board. Full-size, PICMG | Intel Pentium III (FC-PGA) Processor | VGA, SCSI...

Trenton S5927-211-xM CPU Boards-Full Size Single Board Computer Socket 370 Intel Celeron 1.2 GHz Pro...

Trenton S5927-403-xM Full Size Single Board Computer Socket 370 Intel Pentium III 733 MHz Processor,...

Trenton S5927-405-xM Full Size Single Board Computer with Socket 370 Intel Pentium III 866 MHz Proce...
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods