Amplifier/Generator AG 1006 provides an accurate reading is a robust source of RF of VSWR. power for ultrasonic, laser When used as amplifier, the modulation, RFI/EMI, plasma AG 1006 is compatible with generation, laboratory and most signal and function general industrial applications. generators, computer Featuring leading edge solid synthesizer cards within its state design for all RF output and bandwidth limits. Up to 300 Watts of RF amplifier stages and a built-in The Forced-air cooling Power From 20 kHz to DDS signal source, it provides system and the internal everything for a complete and power supply are designed to 14 MHz For Industrial, reliable, controlled RF power permit operation over a wide Laboratory And delivery system. It reflects the range of temperature and T&C ongoing commitment to global AC line conditions. Medical Application. provide RF power products of The AG 1006 is built to the highest quality, withstand a +13 dBm (2.8Vp- FEATURING: incorporating the current p) Input signal. The unit • 20 kHz to 4 MHz up to requirements for complete amplifies the inputs of AM, greater than 300 W remote control and data FM, SSB and pulse acquisition features. modulations. • Output of 250 Watts h3 ≤ -12 dBc OPERATION OUTPUT PROTECTION The AG 1006 produces up to AG 1006 is protected by its • Digital Meter, measures 300 Watts of RF power over a internal control system for forward, reflected and frequency range from lower 300 Watts of total Forward than 20 kHz to higher than 4 Power and 70 Watts of load power MHz. It operates over the Reflected Power. This will • Front Panel Control of entire frequency range without protect the amplifier output band switching or other stage from accidental Amplifier and adjustments. Extended range overdrive at the input and an Generator functions to over 10 MHz is possible extreme mismatch at the • Data acquisition: with reduced output power. Output. Gain is rated at 55 dB with a Status Monitoring & typical gain flatness of ±1.5 GENERAL Power Measurement at dB. T&C’s products are designed Analog Port The Front Panel offers a LCD to be reliable, compact and display of Forward, Reflected light in weight. The use of • RS232 communication: and Load Power readings, RF conservatively rated Full Control Of Status, MGC/AGC setups and components ensures high Amplifier & Generator operating frequency in reliability and eliminates the Generator Mode. need for periodic calibration. Functions Power meters are calibrated • AGC or Power into a 50 Ohm Load and are Leveling: Gain Control accurate when unit operates into matched load. Outside of to better than ±0.5 dB matched condition, the model • Pulse and Sweep of RF AG 1006’s power internal signal measurement system Rev. B, January 2005 AG 1006 Specifications Class Of Operation Spurious Output AC Circuit Protection Class B - 26 dBm equivalent noise level Internally fused on the main DC generated by internal circuits Power Supply, 15A. Frequency Of Operation RF Output Settings & Control 20 kHz to 14 MHz - amplifier AC Input Current (RMS) 20 kHz to 6 MHz - generator - Front Panel EDITOR and function Typical: switches for manual control, RF Out nominal 150W: - RS232 port for GUI or other RF Power Output I ≤ 7A @ 115V / I ≤ 3A @ 220V computer communication. Rear 50 Ohm load: RF Out max 300W: Panel. Up to 200W from 20 kHz to 8 MHz, I ≤ 10A @ 115V / I ≤ 4.2A @ 220V - SubD 25 Analog and Digital I/O . Up to 300W from 20 kHz to 4 MHz Max: 12 A Port power scale 1V=100W. Rear <125W to 14 MHz Panel Pulse and low duty cycle. Cooling Any load: Forced air, temperature Up to 150W continues operation BURST: controlled, heatsink temperature Internal settings: monitored via RS232 GUI Pulse range: 1 to 500 usec Gain interface. Period: 1 to 50 milliseconds 55 dB @ 300W / 0.5 MHz User settings via GUI and RS232 ±1 dB External settings: Acoustic level: DC to > 200 kHz. User defined 45dBa @ Max Fan Speed @ RF Input Drive BURST scheme via SubD-25. temp. Typical range -20 dBm to 0 dBm, See analog port description for more +5 dBm max details. Case Designed to meet EMI and RFI RF Input Drive for AGC SWEEP operation shielding requirements AL chassis, Recommended -5 dBm to 0 dBm for 0.02 to 6 MHz. Min time 10 ms, max yellow conductive finish. ±0.5 dB gain flatness 10s. Settings and activation from GUI Front Panel: T&C off-white. only. Cover: T&C black. Input Drive Source Signal or function generator, analog Output Blanking Dimensions computer output capable of up to 1 Vp- For pulsed applications, T&C (H 135 x W 254 x L 385) mm p @ 50 Ohm (+5dBm) amplifiers and generators offer ( 5.25” x 10” x 15” ) blanking of the output signal for Optional Half Rack, 3U High. Internal RF Source minimum RF spectrum noise. DDS oscillator: 20 kHz to 6 MHz, Less then 1µs Rise/Fall time. Weight 1 kHz resolution 12 kg, 26 lbs. RF Connectors Input and Output Impedance BNC Female: Back Panel Mounting 50 Ohm Stand alone unit. AC Power Source Optional Rack Mount Kit. 2:1 max INPUT VSWR 100 - 120 VAC, 200 - 240 VAC +/- 10%, 47 - 63 Hz Environmental conditions 3:1 max OUTPUT VSWR No adjustment required Temp.: 10° to 35° C ambient Humidity: 80% Output VSWR Protection AC Power Connection 70 W max reflected power limit Equipment intended for ISM appli- IEC Standard Power Entry followed cations in laboratory and light in- by RFI filter. Harmonic Level @ 250W dustrial environment. Filter range 0.1 to 30 MHz minimum. Better then - 12 dBc for 3rd harmonic, any other > -18 dBc AG 1006 Performance Chart 300W 150W T&C Power Conversion, Inc. 110 Halstead Street, Suite 7 100W Rochester, NY 14610, USA Tel: 585-482-5551 Fax: 585-482-8487 4 MHz 10 MHz 14 MHz 0.01 MHz 0.02 MHz http://www.TCPowerconversion.com Total Power Range Nominal Power Output