T&C Power Conversion 120 Watts RF Power at 13.56 MHz for Industrial and Laboratory Applications. FEATURING: • 13.56 MHz up to 120 Watts in peak power RF Power Source • Low harmonic Front Panel view level at 100W, better than –50 RF Power Source Model 0113 is a When used as an amplifier, the dBc any har- 0113 is compatible with most signal robust source of RF power for monic and function generators, computer laser modulation, plasma generation, general laboratory and synthesizer cards and it accurately • Measuring reproduces all waveforms within its general industrial applications. forward, control loop bandwidth limits. Featuring leading edge solid state reflected and design for all generator stages and The Forced-air cooling system and the internal power supply are a built-in DDS signal source, it power VSWR designed to permit operation over a provides everything for a complete simultaneously and reliable, controlled RF power wide range of temperature and global AC line conditions. • Back Panel Con- delivery system. It reflects the T&C The 0113 is built to withstand a +3 ongoing commitment to provide trol & Monitoring RF power products of the highest dBm Input signal. The unit amplifies of all RF power the inputs of AM, and pulse quality, incorporating the current Source functions. modulations. requirements for complete remote Data acquisition: control and data acquisition OUTPUT PROTECTION Status Monitoring 0113 is protected by its internal features & Power monitoring system for 120 Watts of OPERATION total Forward Power and 50W of The 0113 produces 120W of RF Measurement via Reflected Power. This will protect power at a frequency of 13.56 Analog Port MHz, with low harmonic distortion. the RF power supply output stage • AGC Power from extreme mismatch at the Power meters are calibrated into a Leveling: Output Output. 50 Ohm Load and they are GENERAL Power Control to accurate when unit operates into T&C generators are designed to be matched load. Outside of matched better than ±1.5W reliable, compact and light in condition, the model 0113’s power of set value. measurement system provides an weight. The use of conservatively • Pulse operation 110 Halstead Street accurate reading of VSWR. High rated components ensures high Rochester, New York 14610 USA in MGC/Burst level VSWR is also monitored for reliability and eliminates the need Tel: 585.482.5551 Fax: 585.482.8487 protection of output stage and is mode www.tcpowerconversion.com for periodic retuning. sales@tcpowerconversion.com set for 50W limit. www.tcpowerconversion.com Rev. C, October 2008 Page 2 of 2 sales@tcpowerconversion.com T&C POWER CONVERSION 0113 RF Power Source Specifications Spurious Output Class Of Operation AC Circuit Protection - 55 dBm equivalent noise level Class B Internally fused on the main DC generated by internal circuits Power Supply, 6.5A. Frequency Of Operation Output Blanking/Pulsing 13.56 MHz AC Input Current (RMS) For pulsed applications, T&C RF Out 100W: amplifiers and generators offer blanking 100 to 120 VAC - max. I = 6.0 A Frequency Stability of the output signal for minimum noise 200 to 240 VAC - max. I = 3.0 A 0.005% or better RF spectrum. Less then 1µs Rise/Fall Product Features Power Factor time Correction (PFC) RF Power Output 120 Watts into 50 Ohm nominal Dynamic Power Range Cooling 1 to 120W, settings within +/- 2W Forced air, temperature controlled, Operation as amplifier. Contact Note: 0 to more than 120W heatsink temperature monitored for T&C for further details. equipment safety at 70C limit. Output as amplifier in MGC/Burst Mode Output Control Interfaces 0 dBm IN, 1V (5 or 10V) CTL IN pin 5 (Communications) Dimensions 100W +/-2W SubD 25 Analog and Digital I/O . H133 mm x W211 mm x L406 mm D-COM “Digital Communication” RF Input Drive (as amplifier) ( 5.25” x 8.3” x 16” ) Port: (Optional) Typical range -20 dBm to 0 dBm RS-232 1V (5 or 10V) CTL IN pin 5 Weight RS-485 10.5 kg, 22.5 lbs. USB RF Input Drive for AGC Recommended +0 to +3 dBm for the Case Power Monitor Scale best operation Front Panel: T&C White - Powder Selection Coated Steel. User selectable levels down to 1 watt Input Drive Source(amplifier) Chrome Steel Covers and (in three (3) Scales) within tenths of Signal or function generator, analog Chassis. watt accuracy. input capable of up to 2 Vp-p @ 50 Chassis designed to meet EMI RFI Available scales: Ohm shielding requirements 1V=100W 5V=full power Internal RF Source 10V=full power Mounting Crystal oscillator at 13.56 MHz Half Rack, 3U high. Optional: Rack Mount Kit, Adapter Kit, Coupling Pulse Specifications Input and Output Impedance Pulse Width from 2 µs to continues, Screws. 50 Ohm user defined. IN / OUT VSWR Environmental conditions 1.2:1 max - input Temp.: 10° to 40° C ambient RF Power Margin 3:1 max - output (Open Loop Max Power/Rated Power)-1)*100 Humidity: 80% >50 % Equipment intended for ISM applica- Output VSWR Protection tions in laboratory and light industrial 50 Watts max reflected power limit. environment. Rear Panel RF Connectors Automatic, limits typically within 0.5 INPUT BNC Female ms after reverse power reaches 50 OUTPUT N Female Watts or power amplifier current BLANKING BNC Female preset limit. AC Power Connection Harmonic Level @ 100W IEC Standard Power Entry followed by Better than -50 dBc for any harmonic. RFI filter. Filter range 0.1 to 30 MHz min. Sales Representative: T&C Power Conversion, Inc. 110 Halstead Street, Suite 7 Rochester, NY 14610, USA Tel: 585-482-5551 Fax: 585-482-8487 www.tcpowerconversion.com Rev. C, October 2008 Page 2 of 2 www.tcpowerconversion.com sales@tcpowerconversion.com sales@tcpowerconversion.com