STMICROELECTRONICS STP16CPS05MTR
Description
IC LED SINK DRVR 16CH CC 24-SOIC
Part Number
STP16CPS05MTR
Price
Request Quote
Manufacturer
STMICROELECTRONICS
Lead Time
Request Quote
Category
PRODUCTS - S
Datasheet
Extracted Text
STP16CPS05 Low voltage 16-bit constant current LED sink driver with auto power saving Features ■ Low voltage power supply down to 3V ■ 16 constant current output channels ■ Adjustable output current through external SO-24 resistor ■ Serial Data IN/Parallel Data OUT ■ Auto power-saving feature minimizes the quiescent current if no active data is detected TSSOP24 TSSOP24 on the latches (exposed pad) ■ Can be driven by a 3.3V microcontroller ■ Output current: 5-100mA ■ Max clock frequency 30MHz ■ ESD protection 2.5kV HBM, 200V MM Description The output current setup time is 40ns (typ), thus The STP16CPS05 is a monolithic, low voltage, improving the system performance. low current power 16-bit shift register designed for The LEDs' brightness can be controlled by using LED panel displays. The STP16CPS05 contains a an external resistor to adjust the STP16CPS05 16-bit serial-in, parallel-out shift register that output current. feeds a 16-bit, D-type storage register. In the output stage, sixteen regulated current sources The STP16CPS05 guarantees a 20V output provide from 5mA to 100mA constant current to driving capability, allowing users to connect more drive the LEDs. LEDs in series.The high clock frequency, 30MHz, makes the device suitable for high data rate The Auto Power Shut-Down and Auto Power-ON transmission. The 3.3V voltage supply is useful in feature allows the device to save power without applications that interface with a 3.3V any external intervention. microcontroller. Table 1. Device summary Order codes Package Packaging STP16CPS05MTR SO-24 1000 parts per reel STP16CPS05TTR TSSOP24 2500 parts per reel STP16CPS05XTTR TSSOP24 Exposed Pad 2500 parts per reel July 2007 Rev 4 1/25 www.st.com 25 Contents STP16CPS05 Contents 1 Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Pin connection and description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.3 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Equivalent circuit and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5 Timing diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6 Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7 Test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2/25 STP16CPS05 Summary description 1 Summary description Table 2. Typical current accuracy Current accuracy Output voltage Output current V temp. DD Between bits Between ICs ≥ 1.3V ±1.5% ±5% 3.3V to 5V 25°C ≥20 to 100 mA 1.1 Pin connection and description Figure 1. Pin connection Note: The exposed pad is electrically not connected Table 3. Pin description Pin N° Symbol Name and function 1 GND Ground terminal 2 SDI Serial data input terminal 3 CLK Clock input terminal 4 LE Latch input terminal 5-20 OUT 0-15 Output terminal 21 OE Input terminal of output enable (active low) 22 SDO Serial data out terminal 23 R-EXT Input terminal of an external resistor for constant current programing 24 V Supply voltage terminal DD 3/25 Electrical ratings STP16CPS05 2 Electrical ratings 2.1 Absolute maximum ratings Stressing the device above the rating listed in the “Absolute Maximum Ratings” table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 4. Absolute maximum ratings Symbol Parameter Value Unit V Supply voltage 0 to 7 V DD V Output voltage -0.5 to 20 V O I Output current 100 mA O V Input voltage -0.4 to V +0.4 V I DD I GND terminal current 1600 mA GND f Clock frequency 50 MHz CLK 2.2 Thermal data Table 5. Thermal data Symbol Parameter Value Unit T Operating temperature range -40 to +125 °C OPR T Storage temperature range -55 to +150 °C STG DIP-24 60 °C/W TSSOP24 85 °C/W (1) R Thermal resistance junction-case thJC TSSOP24 37.5 °C/W Exposed Pad SO-24 75 °C/W 1. The exposed pad should be soldered directly to the PCB to realize the thermal benefits. 4/25 STP16CPS05 Electrical ratings 2.3 Recommended operating conditions Table 6. Recommended operating conditions at 25°C Symbol Parameter Test conditions Min Typ Max Unit V Supply voltage 3.0 5.5 V DD V Output voltage 20 V O I Output current OUTn 3 100 mA O I Output current SERIAL-OUT +1 mA OH I Output current SERIAL-OUT -1 mA OL V Input voltage 0.7V V +0.3 V IH DD DD V Input voltage -0.3 0.3V V IL DD t LE pulse width 20 ns wLAT t CLK pulse width 16 ns wCLK t OE pulse width 200 ns wEN V = 3.3V to 5.0V DD t Setup time for DATA 20 ns SETUP(D) t Hold time for DATA 15 ns HOLD(D) t Setup time for LATCH 15 ns SETUP(L) (1) f Clock frequency Cascade operation 30 MHz CLK 1. If the device is connected in cascade, it may not be possible achieve the maximum data transfer. Please considered the timings carefully. 5/25 Electrical characteristics STP16CPS05 3 Electrical characteristics Table 7. Electrical characteristics (V =3.3V to 5V, T = 25°C, unless otherwise specified.) DD Symbol Parameter Test conditions Min Typ Max Unit V Input voltage high level 0.7V V V IH DD DD V Input voltage low level GND 0.3V V IL DD I Output leakage current V = 20V 10 µA OH OH Output voltage V I = 1mA 0.4 V OL OL (Serial-OUT) Output voltage V I = -1mA V -0.4V V OH OH DD (Serial-OUT) I V = 0.3V, R = 3.9kΩ 4.25 5 5.75 OL1 O ext I Output current V = 0.3V, R = 970Ω 19 20 21 mA OL2 O ext I V = 1.3V, R = 190Ω 96 100 104 OL3 O ext ∆I V = 0.3VR = 3.9kΩ ± 5 ± 8 OL1 O EXT Output current error ∆I between bit V = 0.3VR = 970Ω ± 1.5 ± 3 % OL2 O EXT (All Output ON) ∆I V = 1.3VR =190Ω ± 1.2 ± 3 OL3 O EXT R Pull-up resistor 150 300 600 KΩ SIN(up) R Pull-down resistor 100 200 400 KΩ SIN(down) V = 3.3V 70 120 µA DD Shut-down current I DD(SH) All Latched Data = L V = 5V 100 150 µA DD R = 970 EXT I 4 DD(OFF1) OUT 0 to 15 = OFF Supply current (OFF) R = 240 EXT I 11.2 DD(OFF2) OUT 0 to 15 = OFF mA R = 970 EXT I 4.5 DD(ON1) OUT 0 to 15 = ON Supply current (ON) R = 240 EXT I 11.7 DD(ON2) OUT 0 to 15 = ON Thermal Thermal protection 170 °C 6/25 STP16CPS05 Electrical characteristics Table 8. Switching characteristics (V = 5V, T = 25°C, unless otherwise specified.) DD Symbol Parameter Test conditions Min Typ Max Unit V = 3.3V 50 70 DD Propagation delay time, t ns PLH1 CLK-OUTn, LE = H, OE = L V = 5V 28 40 DD V = 3.3V 48 70 DD Propagation delay time, t ns PLH2 LE-OUTn, OE = L V = 5V 25 40 DD V = 3.3V 55 75 DD Propagation delay time, t ns PLH3 OE-OUTn, LE = H V = 5V 35 45 DD V = 3.3V 11 16 DD Propagation delay time, t ns PLH CLK-SDO V = 5V 8 12 DD Propagation delay time, V = 3.3V 22 30 DD t CLK-OUTn, LE = H, ns PHL1 V = 3.3 V V = V DD IH DD V = 5V 17 25 OE = L DD V = GND C = 10pF IL L I = 20mA V = 3.0 V V = 3.3V 7 10 DD Propagation delay time, O L t ns PHL2 R = 1KΩ R = 60 Ω LE-OUTn, OE = L EXT L V = 5V 4 6 DD V = 3.3V 18 30 DD Propagation delay time, t ns PHL3 OE-OUTn, LE = H V = 5V 15 25 DD V = 3.3V 12 18 DD Propagation delay time, t ns PHL CLK-SDO V = 5V 8 12 DD Output rise time V = 3.3V 40 80 DD t 10~90% of voltage ns ON V = 5V 22 35 waveform DD Output fall time V = 3.3V 11 15 DD t 90~10% of voltage ns OFF V = 5V 18 25 waveform DD (1) t CLK rise time 5000 ns r (1) t CLK fall time 5000 ns f 1. In order to achieve high cascade data transfer,please consider tr/tf timings carefully. 7/25 Equivalent circuit and outputs STP16CPS05 4 Equivalent circuit and outputs Figure 2. OE terminal Figure 3. LE terminal Figure 4. CLK, SDI terminal 8/25 STP16CPS05 Equivalent circuit and outputs Figure 5. SDO terminal Figure 6. Block diagram 9/25 Timing diagrams STP16CPS05 5 Timing diagrams Table 9. Truth table SERIAL- CLOCK LE OE OUT0 ............. OUT7 ................ OUT15 SDO IN H L Dn Dn ..... Dn - 7 ..... Dn -15 Dn - 15 L L Dn + 1 No Change Dn - 14 H L Dn + 2 Dn + 2 ..... Dn - 5 ..... Dn -13 Dn - 13 X L Dn + 3 Dn + 2 ..... Dn - 5 ..... Dn -13 Dn - 13 X H Dn + 3 OFF Dn - 13 Note: OUTn = ON when Dn = H OUTn = OFF when Dn = L Figure 7. Timing diagram Note: The latches circuit holds data when the LE terminal is Low. 1 When LE terminal is at High level, latch circuit hold the data it passes from the input to the output. 2 When OE terminal is at Low level, output terminals OUT0 to OUT15 respond to the data, either ON or OFF. 3 When OE terminal is at High level, it switches off all the data on the output terminal. 10/25 STP16CPS05 Timing diagrams Table 10. Enable IO: shut-down truth table Auto CLOCK LE SDI ........... SDI ............ SDI SH OUTn 0 7 15 Power-up H All = L Active Not Active OFF L No Change No Change No Change No Change H One or more = H Not Active Active X Note: At the Power-up the device starts in Shut-Down mode. Figure 8. Clock, serial-in, serial-out 11/25 Timing diagrams STP16CPS05 Figure 9. Clock, serial-in, latch, enable, outputs Figure 10. Outputs 12/25 STP16CPS05 Typical characteristics 6 Typical characteristics Figure 11. Output current-R resistor EXT Table 11. Output current-R resistor EXT Rext (Ohm) Output current (mA) 976 20 780 25 652 30 560 35 488 40 433 45 389 50 354 55 325 60 300 65 278 70 259 75 241 80 229 85 215 90 13/25 Typical characteristics STP16CPS05 Figure 12. Output current vs ± ∆I (%) OL Figure 13. I vs drop out voltage (V ) SET drop 14/25 STP16CPS05 Typical characteristics Figure 14. I ON\OFF DD Figure 15. Auto power saving CH1 = Clock CH2 = SDI CH3 = Latch CH4 = Supply Current Note: Auto power-saving feature minimizes the quiescent current if no active data is detected on the latches and auto-power-up the device at fist active data latched. 15/25 Test circuit STP16CPS05 7 Test circuit Figure 16. DC characteristic Figure 17. AC characteristic 16/25 STP16CPS05 Test circuit Figure 18. Typical application schematic + C = 10µF Note: V will be determined by the V of the LEDs L F Test condition: Temp. = 25°C, V = 3.0V, V = V , C = 10pF, Freq. = 1MHz, DD IN DD L Ch1 = CLK, Ch2 = SDI, Ch3 = OUTn , Ch4 = V OUT Figure 19. Turn ON output current setup Figure 20. Turn OFF output current setup 17/25 Package mechanical data STP16CPS05 8 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com ` 18/25 STP16CPS05 Package mechanical data Table 12. TSSOP24 mechanical data mm. inch Dim. Min Typ Max Min Typ Max A 1.1 0.043 A1 0.05 0.15 0.002 0.006 A2 0.9 0.035 b 0.19 0.30 0.0075 0.0118 c 0.09 0.20 0.0035 0.0079 D 7.7 7.9 0.303 0.311 E 4.3 4.5 0.169 0.177 e 0.65 BSC 0.0256 BSC H 6.25 6.5 0.246 0.256 K 0° 8° 0° 8° L 0.50 0.70 0.020 0.028 Figure 21. TSSOP24 package dimensions 19/25 Package mechanical data STP16CPS05 Table 13. Tape and reel TSSOP24 mm. inch Dim. Min Typ Max Min Typ Max A 330 2.992 C 12.8 13.2 0.504 0.519 D 20.2 0.795 N 60 2.362 T 22.4 0.882 Ao 6.8 7 0.268 0.276 Bo 8.2 8.4 0.323 0.331 Ko 1.7 1.9 0.067 0.075 Po 3.9 4.1 0.153 0.161 P 11.9 12.1 0.468 0.476 Figure 22. Reel dimensions 20/25 STP16CPS05 Package mechanical data Table 14. SO-24 mechanical data mm. inch Dim. Min Typ Max Min Typ Max A 2.65 0.104 a1 0.1 0.2 0.004 0.008 a2 2.45 0.096 b 0.35 0.49 0.014 0.019 b1 0.23 0.32 0.009 0.012 C 0.5 0.020 c1 45°(typ.) D 15.20 15.60 0.598 0.614 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 13.97 0.550 F 7.40 7.60 0.291 0.300 L 0.50 1.27 0.020 0.050 S °(max.) 8 Figure 23. SO-24 package dimensions 21/25 Package mechanical data STP16CPS05 Table 15. Tape and reel SO-24 mm. inch Dim. Min Typ Max Min Typ Max A 330 12.992 C 12.8 13.2 0.504 0.519 D 20.2 0.795 N 60 2.362 T 30.4 1.197 Ao 10.8 11.0 0.425 0.433 Bo 15.7 15.9 0.618 0.626 Ko 2.9 3.1 0.114 0.122 Po 3.9 4.1 0.153 0.161 P 11.9 12.1 0.468 0.476 Figure 24. Reel dimensions 22/25 STP16CPS05 Package mechanical data Table 16. TSSOP24 exposed-pad mm inch Dim. Min Typ Max Min Typ Max A 1.2 0.047 A1 0.15 0.004 0.006 A2 0.8 1 1.05 0.031 0.039 0.041 b 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 7.7 7.8 7.9 0.303 0.307 0.311 D1 2.7 0.106 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.5 0.169 0.173 0.177 E2 1.5 0.059 e 0.65 0.0256 K 0° 8° 0° 8° L 0.45 0.60 0.75 0.018 0.024 0.030 Figure 25. TSSOP24 dimensions 23/25 Revision history STP16CPS05 9 Revision history Table 17. Revision history Date Revision Changes 28-Jul-2006 1 First release 22-Dec-2006 2 Final datasheet 17-May-2007 3 Updated Table 8 on page 7 10-Jul-2007 4 Updated Table 9: Truth table on page 10 24/25 STP16CPS05 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 25/25
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the STP16CPS05MTR have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers





What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods