GPFC110 Commercial 110 Watt Global Performance Switchers FEATURES: 3.1 watts/cu.in. power density Compact size (6.3" x 3.75" x 1.62"; meets 1U height) Power factor corrected to IEC 1000-3-2 Class A Less than 300 µA leakage EMI compliance to CISPR 22, FCC Class B Approved to UL1950, IEC950 and CSA 22.2 No. 950 2-year warranty marked to LVD SPECIFICATIONS: Ac Input EMI/EMC Compliance 85-264 Vac, 47-63 Hz single phase. All models include built-in EMI filtering to meet the following emissions requirements: Input Current EMI SPECIFICATIONS COMPLIANCE LEVEL Maximum input current 2.3 A at 90 Vac, 60 Hz with full Conducted Emissions EN55022 Class B; FCC Class B rated load. Input current harmonic content meets the Static Discharge EN61000-4-2, 6 kV contact, 8 kV ai requirements of IEC1000-3-2. RF Field Susceptibility EN61000-4-3, 3 V/meter Fast Transients/Bursts EN61000-4-4, 2 kV, 5 kHz Hold-up Time Surge Susceptibility EN61000-4-5, 1 kV diff., 2 kV com. 25 ms minimum from loss of ac input at full load, nominal Line Frequency Harmonics EN61000-3-2 Class A line (115 Vac). Inrush Current Output Power Inrush 240 Vac is less than 37 A, averaged over the first Total regulation is the maximum deviation from the ac half-cycle under cold start conditions. Limiting pro- nominal voltage for all steady-state loading conditions. vided by internal thermistors. Each individual output is to be used within its specified limits of that output. Peak ratings are for 60 s maximum Fan Output duration, 10% duty cycle. An additional output, same as Vout, suitable for powering a dc fan is included in all models. The output is protected Overload Protection by an internal resistor in the event of an overload. Fully protected against short circuit and output overload. Short circuit protection is cycling type power limit. Power Fail Recovery after fault is automatic. TTL or CMOS compatible output goes low (<0.5 V) 8 ms before output voltage drops more than 4% below nominal Output Noise voltage upon loss of ac power. The signal is factory set to 0.5% rms, 1% pk-pk, 20 MHz Bandwidth, differential trip when input power can no longer sustain the output. mode. Measured with noise probe directly across output terminals of the power supply. Temperature Coefficient 0.03%/°C typical on all outputs. Transient Response 500 ms typical response time for return to within 0.5% of Environmental final value for a 50% load step change, Δi/Δ t< 0.2 A/ms. Designed for 0 to 50°C operation at full rated output Maximum voltage deviation is 3.5%. Load must not go power; derate output current and total output power by below stated minimum. 2.5% per °C above 50°C. See Environmental and Packaging Specifications on the next page. Remote Sense Provided as a standard feature. Capable of compensating Commercial Safety for 0.25 V total of cabling losses in voltage. Approved to UL1950, CSA22.2 No. 234 Level 3, IEC950, EN60950 and CISPR22. UL file #E135803 commercial; Overvoltage Protection CSA #LR46516. The output(s) are intended for safety OVP crowbar reduces output voltage below nominal earthed Signal Output and Intermediate Circuits only. All rating in less than 50 ms. dc outputs are SELV under normal and single fault conditions. Voltage Adjustment Main output ±5%. Input Protection Internal ac fuse provided on all models. Fuse does not blow on overload or short circuit—fuse blows only if catastrophic failure occurs in the unit. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 48 GPFC110 Commercial 110 Watt Single Output Commercial Output Output Output Model Output No. Output Minimum Maximum (A) Maximum (B) Total Regulation OVP Setpoint Notes GPFC110-5 1V5A .1 0A1A 1 1% 5 2V6C .2 ± 0.6 GPFC110-12 1V1A 2 0A6A .7 9% .2 2V1C 4 ± 1.1 GPFC110-15 1V1A 5 0A5A .3 7% .3 2V1C 8.5 ± 1.5 GPFC110-24 1V2A 4 0A3A .4 4% .6 2V2C 8 ± 2.5 GPFC110-28 1V2A 8 0A2A .9 3% .9 2V3C 4 ± 2.8 GPFC110-48 1V4A 8 0A1A .7 2% .3 2V5C 5 ± 4 A. With unrestricted convection cooling. B. With 26cfm airflow. C. Output current limited by primary power limit. Degree of output load on all outputs will affect maximum overload current. GPFC110 MECHANICAL SPECIFICATIONS Environmental Operating Non-operating Specification o Ts emperature (A)S5 ee individual spec -40 to +8 C HH umidity (A)0H to 95% R 0 to 95% R A. Units should be allowed to warm up/operate under non-condensing conditions before application of power. Sg hock (B) 20 40 g pk pk B. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to 2000Hz, 3 orthogonal axes. Tested for 10 min./axis operating and 1 hr./axis non-operating. At ltitude-t 500 to 10,000 f -500 to 40,000 f C. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, 3 orthogonal axes, 2 2 Vg ibration (C) 1.5 , 0.003 g/g Hz 5 , 0.026 g /Hz total 6 shocks. rms rms Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 49