SCHNEIDER ELECTRIC ABL7

 PHASEO Power Supplies ABL7 Class 8440 December 00 CONTENTS Description Page Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TM PHASEO Power Supplies Overview The ABL7RE and ABL7RP single phase switching power supplies are designed to provide the dc voltage necessary for most control system circuits. These power supplies are totally electronic and regulated. The use of electronics makes it possible to signiŢcantly improve the performance of these power supplies. They provide: — Compact size — Integrated overload, short circuit, overvoltage and undervoltage protection — A wide range of permitted input voltages, without any adjustment — A high degree of output voltage stability — Good performance — Considerably reduced weight as compared to competition These power supplies, which are accurate to 3% regardless of the load or the type of supply voltage within the range of 85-364 Vac. The inclusion of overload and short circuit protection makes downstream protection unnecessary in most applications. They have an output undervoltage control which will cause the power supply to trip if the output voltage of a 24 Vdc supply drops below 19 Vdc, to ensure that the voltage is always usable by the devices being supplied. All products have an output voltage adjustment potentiometer (24 to 28.8 V on a 24 Vdc supply). It allows you to compensate for any line voltage drop in installations with long runs. The ABL7RE products are excellent for typical industrial applications. The ABL7RP products are more general purpose. These supplies have an input Ţlter (PFC) which allows them to be used in commercial environments. They have 2 operating modes: “AUTO” mode which automatically restarts as soon as the fault is cleared. “MANU” mode which requires the power supply to be reset before restarting is possible. Resetting is achieved by switching off the supply voltage and reapplying it. Harmonics (Power Factor) – The current drawn by a power supply is non-sinusoidal. This leads to the existence of harmonic currents which pollute the main supply. European standard EN 61000-3-2 limits the harmonic currents produced by power supplies. This standard covers all devices of more the 75 W, drawing up to 16 A per phase, and connected directly to the public power supplies. Devices connected downstream of a private, low voltage, general transformer are excluded. However, switching power supplies produce harmonic current. Therefore, a Ţlter circuit (Power Factor Correction or PFC) must be added to comply with standard EN61000-3-2. The ABL7RP power supplies conform to the EN61000-3- 2 standard and can be connected directly to the public power supply system. 1 www.schneider-electric.ca 12/00 TM PHASEO Power Supplies Application Data Technical Specifications Type of Power Supply ABL7RE ABL7RP Approvals UL508: File E164867 CCN NMTR, CSA 22.2 No. 950: File 204701 Class 5311 03, TÜV Conforming to Standards Safety IEC 950 EMC EN50081- 2, IEC61000-6-2 (EN50082-2) Low Frequency Harmonic Currents – EN61000-3-2 Input Circuit Input voltages Rated values 100 to 240 Vac 100 to 240 Vac, 110 to 220 Vdc 85 to 264 Vac single-phase Permissible values 85 to 264 Vac single-phase 99 to 250 Vdc Permissible frequencies 47 to 63 Hz EfŢciency at nominal load > 85% Current at switch-on < 30 A Power factor 0.65 0.98 Output Circuit Precision Output voltage Adjustable, from 100 to 120% Line and load regulation ± 3% Residual ripple - interference < 200 mV Micro-breaks Holding time at I max and Ve min > 10 ms > 20 ms Overloads Permissible peak current Not limited for 100 ms (under voltage protection not active) Protection Permanent/automatic restart or Short-circuit Permanent/automatic restart manual restart on product Overload 1.1 In Overvoltage Tripping if U > 1.5 Un Undervoltage Tripping if U < 0.8 Un Operational and Environmental Characteristics Connections 2 Input 2 - # 14 AWG (2 x 2.5 mm ) + ground 2 Output 2 - # 14 AWG (2 x 2.5 mm ) + ground, multiple output, depending on model Ambient conditions Storage Temperature -13 to 158 ˚F (- 25 to + 70 ˚C) Operating Temperature 32 to 140 ˚F (0 to + 60 ˚C), derating from 122 ˚F (50 ˚C) Maximum Relative Humidity 95% without condensation or dripping water Degree of Protection IP 20 conforming to IEC529 Vibrations Conforming to EN61131-2 Operating position Vertical MTBF > 100 000 h [Conforming to Bell Core, at 104 ˚F (40˚ C)] Connections Series Possible Parallel Possible [maximum temperature 122 ˚F (50˚ C)] Dielectric strength Input/output 3000 V/50 Hz 1 min Input/ground 3000 V/50 Hz 1 min Output/ground (and output/output) 500 V/50 Hz 1 min Input fuse incorporated Yes, not interchangeable Emissions EN50081-1 (Generic) Conducted/radiated EN55011/EN55022 cl.B Immunity IEC61000-6-2 (Generic) Electrostatic Discharge EN61000-4-2 (4 kV contact/8 kV air) Electromagnetic EN61000-4-3 level 3 (10 V/m) Conducted Interference EN61000-4-4 level 3 (2 kV), EN61000-4-5, EN61000-4-6 level 3, EN61000-4-8 level 4. Mains Interference EN1000-4-11 (Voltage drops and cuts) 2 www.schneider-electric.ca 12/00 TM PHASEO Power Supplies Application Data DERATING The ambient temperature is a determining factor which limits the power that an electronic power supply can deliver continuously. A temperature which is too high around the electronic components signiŢcantly reduces their life. However, if the ambient temperature remains largely below the rated operating temperature, then a power supply can deliver more than its nominal power. The rated ambient temperature for PHASEO power supplies is 122 ˚F (50 ˚C). Below this temperature, an increase in rating is possible up to 120% of the nominal power. Above 122 ˚F (50 ˚C), a derating is necessary up to a maximum temperature of 140 ˚F (60 ˚C). The graph below shows the power (in relation to the nominal power) which the power supply unit can deliver continuously, according to the ambient temperature. 140 120 100 80 60 40 20 0 0 10 20 30 40 50 60 70 Operational ambient temperature (˚ C) Derating should also be considered in the following extreme operating conditions: — Intensive operation (output current permanently close to the nominal current, combined with a high ambient temperature) — output voltage set above 24V (to compensate for line voltage drops, for example) — parallel connection to increase the total power ABL7 RE ABL7 RP Without derating, from 32 ˚F to 122 ˚F (0 ˚C to 50 ˚C). Intensive Operation Derating of nominal current by 1% per additional ˚C up to 140 ˚F (60 ˚C) The nominal power is Ţxed. Rise in Output Voltage Increasing the output voltage means that the current delivered must be reduced. The total power is equal to the sum of the powers of the power supplies used, but the maximum Parallel Connection to ambient temperature for operation is 122 ˚F (50 ˚C). Increase the Power To improve heat dissipation, the power supplies must not be in contact with each other. In all cases, there must be adequate air circulation round the products to ensure easier cooling. There must be a clear space of 1.97 in (50 mm) above and below PHASEO power supplies and of 0.59 in (15 mm) at the sides. Type of Supply 115 VAC Single-Phase 230 VAC Single-Phase Thermal-Magnetic Supplementary Thermal-Magnetic Supplementary Type of Protection gG Fuse gG Fuse Protector Protector Single-pole GB2CB 2-pole GB2DB C60N GB2DB C60N ABL7RE2402 GB2B07 MG24517 2 A GB2DB06 MG24516 2 A ABL7RE2403 GB2B07 MG24517 2 A GB2DB06 MG24516 2 A ABL7RE2405 GB2B08 MG24518 4 A GB2DB07 MG17453 2 A ABL7RE2410 GB2B12 MG17454 6 A GB2DB08 MG24518 4 A ABL7RP2403 GB2B07 MG 24517 2 A GB2DB07 MG24516 2 A ABL7RP2405 GB2B07 MG24517 2 A GB2DB07 MG24516 2 A ABL7RP2410 GB2B09 MG24519 4 A GB2DB07 MG24516 2 A ABL7RP4803 GB2 B07 MG24517 2 A GB2DB07 MG24516 2 A 3 www.schneider-electric.ca 12/00 Percent of rated power TM PHASEO Power Supplies Selection - Dimensions and Wiring Single Phase Regulated Switch Mode Power Supplies ABL7RE Mains Input Automatic Complies with Output Nominal Nominal Catalog Weight Voltage Protection Standard Voltage Power Current Number lb (kg) 47-63 Hz Reset EN-61000-3-2 100 to 240 Vac 24 Vdc 48 W 2 A Auto No ABL7RE2402 1.14 lb (0.520 kg) Single Phase 72 W 3 A Auto No ABL7RE2403 1.14 lb (0.520 kg) Wide Range 120 W 5 A Auto No ABL7RE2405 2.20 lb (1.000 kg) 240 W 10 A Auto No ABL7RE2410 4.85 lb (2.200 kg) Single Phase Regulated Switch Mode Power Supplies ABL7RP Mains Input Automatic Complies with Output Nominal Nominal Catalog Weight Voltage Protection Standard Voltage Power Current Number lb (kg) 47 -63 Hz Reset EN-61000-3-2 ABL7RE2405 100 to 240 Vac 12 Vdc 60 W 5 A Auto/Man Yes ABL7RP1205 2.20 lb (1.000 kg) ABL7RP2405 100 to 250 Vdc 24 Vdc 72 W 3 A Auto/Man Yes ABL7RP2403 1.14 lb (0.520 kg) ABL7RP4803 Single Phase Wide Range 120 W 5 A Auto/Man Yes ABL7RP2405 2.20 lb (1.000 kg) 240 W 10 A Auto/Man Yes ABL7RP2410 4.85 lb (2.200 kg) 48 Vdc 144 W 3 A Auto/Man Yes ABL7RP4803 2.2 lb (1.000 kg) 7RE2410 ABL7RE24 /ABL7RP 7RE2405 7RE2402/2403 7RP2410 7RP1205/2405/4803 7RP2403 Common side view Clip-on mounting on 35 and 75 mm rails 1.06 4.72 2.13 5.37 120 54 135 27 in Dual Dimensions = mm ABL7RE2402/2403 ABL7RE2405 ABL7RE2410 Vac Vac Vdc Vdc Vac Vdc ABL7RE2403 ABL7RE1205/2405/4803 ABL7RE2410 Filter Filter Filter Filter Vac Vac Vac Vac Vdc Vdc Vdc Vdc 4 www.schneider-electric.ca 12/00 N N + L + L – – 4.72 + + 120 N N – – L L + + – – 4.72 120 + + + N N N – – – L L L + + + – – – + + + – – – 4.72 120 Schneider Electric Head OfŢce 19 Waterman Avenue Toronto, Ontario M4B 1Y2 www.schneider-electric.ca Tel: (416) 752-8020 Fax: (416) 752-6230 T8440CT0002EP R0 December, 2000 © 2000 Schneider Canada, All Rights Reserved