Fox (LP3500) C-Programmable Single-Board Computer User’s Manual 019–0111 • 081121–L Fox (LP3500) User’s Manual Part Number 019-0111 • 081121–L • Printed in U.S.A. ©2002–2008 Digi International Inc. • All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without the express written permission of Digi International. Permission is granted to make one or more copies as long as the copyright page contained therein is included. These copies of the manuals may not be let or sold for any reason without the express written permission of Digi International. Digi International reserves the right to make changes and improvements to its products without providing notice. Trademarks Rabbit and Dynamic C are registered trademarks of Digi International Inc. Rabbit 2000 and RabbitCore are trademarks of Digi International Inc. The latest revision of this manual is available on the Rabbit Web site, www.rabbit.com, for free, unregistered download. Digi International Inc. www.rabbit.com Fox (LP3500) TABLE OF CONTENTS Chapter 1. Introduction 1 1.1 LP3500 Description ..............................................................................................................................1 1.2 LP3500 Features ...................................................................................................................................2 1.3 Optional Add-Ons.................................................................................................................................3 1.4 Development and Evaluation Tools......................................................................................................4 1.4.1 Tool Kit .........................................................................................................................................4 1.4.2 Software ........................................................................................................................................5 1.5 CE Compliance .....................................................................................................................................6 1.5.1 Design Guidelines .........................................................................................................................7 1.5.2 Interfacing the LP3500 to Other Devices .....................................................................................7 Chapter 2. Getting Started 9 2.1 LP3500 Connections.............................................................................................................................9 2.2 Remove Battery Tab ...........................................................................................................................13 2.3 Installing Dynamic C ..........................................................................................................................14 2.4 Starting Dynamic C ............................................................................................................................14 2.5 PONG.C..............................................................................................................................................15 2.6 Where Do I Go From Here? ...............................................................................................................15 Chapter 3. Subsystems 17 3.1 LP3500 Pinouts...................................................................................................................................18 3.1.1 Headers and Screw Terminals.....................................................................................................18 3.2 Power Modes ......................................................................................................................................19 3.2.1 Setting the Power-Save Mode.....................................................................................................20 3.2.2 Operating in the Power-Save Mode ............................................................................................21 3.2.3 Resuming Normal-Power or Low-Power Operation ..................................................................21 3.3 Digital I/O ...........................................................................................................................................22 3.3.1 Digital Inputs...............................................................................................................................22 3.3.2 Digital Outputs............................................................................................................................23 3.4 Serial Communication ........................................................................................................................25 3.4.1 RS-232 ........................................................................................................................................26 3.4.2 RS-485 ........................................................................................................................................26 3.4.3 Serial Interface Port ....................................................................................................................28 3.4.4 Programming Port.......................................................................................................................28 3.5 Display Interface.................................................................................................................................30 3.6 A/D Converter Inputs (LP3500 only) .................................................................................................31 3.7 PWM Outputs .....................................................................................................................................33 3.8 Relay Output Circuit (LP3500 only) ..................................................................................................34 3.9 Serial Programming Cable..................................................................................................................35 3.9.1 Changing Between Program Mode and Run Mode ....................................................................35 3.9.2 Standalone Operation of the LP3500 ..........................................................................................36 3.10 Other Hardware.................................................................................................................................36 3.10.1 Spectrum Spreader ....................................................................................................................36 3.11 Memory.............................................................................................................................................37 3.11.1 SRAM .......................................................................................................................................37 3.11.2 Flash Memory ...........................................................................................................................37 User’s Manual Chapter 4. Software 39 4.1 Upgrading Dynamic C ....................................................................................................................... 41 4.1.1 Patches and Bug Fixes................................................................................................................ 41 4.1.2 Extras.......................................................................................................................................... 41 4.2 Sample Programs................................................................................................................................ 42 4.2.1 Power Modes.............................................................................................................................. 42 4.2.2 Digital I/O................................................................................................................................... 42 4.2.3 Serial Communication ................................................................................................................ 43 4.2.4 A/D Converter Inputs ................................................................................................................. 43 4.2.5 PWM Outputs............................................................................................................................. 44 4.2.6 Relay Output............................................................................................................................... 44 4.2.7 Vcc Monitoring .......................................................................................................................... 44 4.2.8 LP3500 Calibration .................................................................................................................... 44 4.2.9 LCD/Keypad Module Sample Programs.................................................................................... 45 4.3 LP3500 Libraries................................................................................................................................ 46 4.4 LP3500 Function Calls....................................................................................................................... 47 4.4.1 LP3500 Power Modes ................................................................................................................ 47 4.4.2 Board Initialization..................................................................................................................... 51 4.4.3 Digital I/O................................................................................................................................... 52 4.4.4 Serial Communication ................................................................................................................ 54 4.4.5 A/D Converter Inputs ................................................................................................................. 56 4.4.6 Vcc Monitoring (LP3500 only).................................................................................................. 68 4.4.7 PWM Outputs............................................................................................................................. 69 4.5 Relay Output (LP3500 only).............................................................................................................. 70 Appendix A. LP3500 Specifications 71 A.1 Electrical and Mechanical Characteristics ........................................................................................ 72 A.1.1 Exclusion Zone.......................................................................................................................... 75 A.1.2 Headers ...................................................................................................................................... 76 A.2 Conformal Coating............................................................................................................................ 77 A.3 Jumper Configurations ...................................................................................................................... 78 A.4 Use of Rabbit 3000 Parallel Ports ..................................................................................................... 81 Appendix B. Prototyping Board 85 B.1 Mechanical Dimensions and Layout ................................................................................................. 86 B.2 Using the Prototyping Board ............................................................................................................. 87 B.2.1 Interface to LP3500 ................................................................................................................... 87 B.2.2 Demonstration Board................................................................................................................. 88 B.2.3 Prototyping Area........................................................................................................................ 88 Appendix C. LCD/Keypad Module 89 C.1 Specifications..................................................................................................................................... 89 C.2 Contrast Adjustment.......................................................................................................................... 91 C.3 Keypad Labeling................................................................................................................................ 92 C.4 Header Pinouts................................................................................................................................... 93 C.4.1 I/O Address Assignments .......................................................................................................... 93 C.5 Bezel-Mount Installation ................................................................................................................... 94 C.6 Connect the LCD/Keypad Module to Your LP3500......................................................................... 96 C.7 LCD/Keypad Module Function Calls................................................................................................ 97 C.7.1 LEDs .......................................................................................................................................... 97 C.7.2 LCD Display.............................................................................................................................. 98 C.7.3 Keypad ..................................................................................................................................... 115 C.8 Sample Programs............................................................................................................................. 118 Appendix D. Plastic Enclosure 119 D.1 Assembly Instructions ..................................................................................................................... 120 D.2 Dimensions...................................................................................................................................... 122 Fox (LP3500) Appendix E. Power Management 123 E.1 External Power Supply.....................................................................................................................123 E.2 Batteries and External Battery Connections.....................................................................................125 E.2.1 Replacing the Backup Battery ..................................................................................................126 E.2.2 Power to VRAM Switch...........................................................................................................126 E.2.3 Reset Generator ........................................................................................................................127 E.3 Chip Select Circuit ...........................................................................................................................127 Appendix F. Running a Sample Program 129 Index 131 Schematics 135 User’s Manual Fox (LP3500) 1. INTRODUCTION The LP3500 is a low-power single-board computer with built-in analog and digital I/O. Although the LP3500 was designed spe- cifically for low-power applications and data logging, it has a host of features that make it attractive for other applications as well. Low power is often required in portable equipment operat- ing from batteries or from solar power. The LP3500 is ideal for monitoring equipment or processes that are far-removed from a power supply, remote telemetry (RTUs), pipeline control and monitoring, well-head monitoring; and use on mobile equipment such as refrigeration trucks. An optional plastic enclosure and an LCD/keypad module are available. The Tool Kit has the essentials that you need to design your own low-power microprocessor-based system, and includes a com- plete Dynamic C software development system. 1.1 LP3500 Description The LP3500 is a low-power single-board computer that incorporates the powerful and low-EMI Rabbit 3000 microprocessor, flash memory, static RAM, digital I/O ports, A/D converter inputs, PWM outputs, RS-232/RS-485 serial ports, and both parallel and serial interfaces that allow other devices to be connected to the LP3500. All aspects of the LP3500 are designed for low power consumption and operates at a vari- ety of power levels, including a power-save mode, to fit customer-specified conditions at any given time. The CPU runs at a nominal speed of 7.4 MHz, and operates at 2.8 V to conserve power. The LP3500 consumes less than 20 mA when fully operational, and less than 100 µA when in the power-save mode. A replaceable coin-type battery will allow the LP3500 to operate in sleep mode for over 3 years. The LP3500 is normally powered from an external battery or power supply. When the unit is in the power-save mode, it can be awakened by an internal timer, an RS-232 signal, or via polling of an external input. The LP3500 can be switched from the power-save mode to full operation and back under pro- gram control. In addition, various sections of circuitry (such as the RS-232 ports) can be switched off under program control to further conserve power when not in use. User’s Manual 1 1.2 LP3500 Features ® • Rabbit 3000 microprocessor operating at up to 7.4 MHz.  512K/128K static RAM and 512K/256K flash memory options.  26 digital I/O: 16 protected digital inputs and 10 high-current digital outputs provide sinking and sourcing outputs.  8 single-ended or 4 differential analog channels with Vcc monitoring option: 11-bit single- ended or 12-bit differential channels.  3 PWM outputs.  Six serial ports 1 RS-485 3 RS-232 (one 5-wire and one 3-wire or three 3-wire), jumper option for logic-level outputs; Serial Port E has a “listen” and “wake-up” capability 1 logic-level serial interface for optional add-ons 1 asynchronous clocked serial port dedicated for programming  Battery-backed real-time clock.  Watchdog supervisor. Two LP3500 models are available. Their standard features are summarized in Table 1. Table 1. LP3500 Models Feature LP3500 LP3510 Microprocessor Rabbit 3000 running at 7.4 MHz Static RAM 512K 128K Flash Memory 512K 256K A/D Converter Inputs (ranges from 0–1 V DC to 0–20 V DC, 4 channels Yes No may be individually configured for 4–20 mA) C-form Bistable Relay Yes No Appendix A provides detailed specifications. The LP3500 can be mounted in two ways. It can be mounted to a panel or on a plastic- enclosure base, which allows I/O connections to be made using traditional connectors with 0.1" spacing. The LP3500 can also be inverted and mounted directly to mating connectors on a motherboard of the customer's design. The first approach is appropriate where I/O connections go directly to devices and switches. The second approach is appropriate where additional circuitry is incorporated on the motherboard. 2 Fox (LP3500) 1.3 Optional Add-Ons  Plastic enclosure (can be wall-mounted or panel-mounted), which consists of a base and a cover for either the LP3500 by itself or an assembly made up of the LP3500 and the LP3500 Prototyping Board. The base is also available separately.  The Prototyping Board included with the Tool Kit is a convenient means of interfacing to the LP3500 via the screw-terminal headers on the Prototyping Board. The Prototyp- ing Board is also available for separate purchase.  4M and 8M SF1000 serial flash expansion cards.  LCD/keypad module with 7-key keypad and seven LEDs. Further details on the Prototyping Board, the plastic enclosure, and the LCD/keypad module are provided in Appendix B, Appendix C, and Appendix D. Visit our Web site for up-to-date information about additional add-ons and features as they become available. The Web site also has the latest revision of this user’s manual and schematics. User’s Manual 3 ��� ��� ��� ��� ��� ��� � �� �� �� ������������������������������������������������������������������������������������������������������������������������������������������������������������������ 1.4 Development and Evaluation Tools 1.4.1 Tool Kit A Tool Kit contains the hardware essentials you will need to develop applications with the LP3500 single-board computer. The items in the Tool Kit and their use are as follows.  LP3500 Getting Started instructions.  Dynamic C CD-ROM, with complete product documentation on disk.  Programming cable, used to connect your PC serial port to the LP3500.  Universal AC adapter, 12 V DC, 1 A (includes Canada/Japan/U.S., Australia/N.Z., U.K., and European style plugs). If you are using another power supply, it must provide 3 to 30 V DC.  Prototyping Board with pushbutton switches, LEDs, and screw-terminal headers. The Prototyping Board can be hooked up to the LP3500 to demonstrate the I/O capabilities of the LP3500 and to provide a prototyping area for you to develop your own add-on circuits. The screw-terminal headers extend the LP3500’s headers for development, and can also be used in a production environment.  Plastic enclosure with four screws.  Four standoffs with mounting screws.  Screwdriver.  Rabbit 3000 Processor Easy Reference poster.  Registration card. ����������� ����� ���� ���������� %�������� &��&��"��� ���’������ ��� ��� ��� ��� ��� ���� ��� ��� �� �� �� � �� �� �� � �������� ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ � ����������� ������!"����#���� Fox (LP3500) The LP3500 is a low-power single-board computer designed to operate reliably virtually any place it is deployed, especially where power is limited. These Getting Started instructions included with the Tool Kit will help you get your LP3500 up and running so that you can run the sample programs to explore its capabilities and develop your own applications. Tool Kit Contents The LP3500 Tool Kit contains the following items: • Dynamic C CD-ROM, with complete product documentation on disk. • Programming cable, used to connect your PC serial port to the LP3500. • Universal AC adapter, 12 V DC, 1 A (includes Canada/Japan/U.S., Australia/N.Z., U.K., and European style plugs). • Prototyping Board with pushbutton switches, LEDs, and screw-terminal headers. The Prototyping Board can be hooked up to the LP3500 to demonstrate the I/O capabilities of the LP3500 and to provide a prototyping area for you to develop your own add-on circuits. • Plastic enclosure with four screws. • Four standoffs with mounting screws. • Screwdriver. • Getting Started instructions. • Rabbit 3000 Processor Easy Reference poster. • Registration card. Visit our online Rabbit store at www.rabbit.com/store/ for the latest information on peripherals and accessories that are available for the LP3500 single-board computers. ® Step 1 — Install Dynamic C Before doing any development, you must install Dynamic C. Insert the CD from the Development Kit in your PC’s CD-ROM drive. If the installation does not auto-start, run the setup.exe program in the root directory of the Dynamic C CD. Install any Dynamic C modules after you install Dynamic C. Rabbit and Dynamic C are registered trademarks of Digi International Inc. ������� � ���������� ��������������� ��������$�������� ������������ Figure 1. LP3500 Tool Kit 4 Fox (LP3500) ��� �!���������!��������!�������!� �� � �� �� !� !� !� !� ����������������������������������������������������������������������������������������������������������������������������������������������� 1.4.2 Software The LP3500 is programmed using version 7.26P or later of Rabbit’s Dynamic C. A com- patible version is included on the Tool Kit CD-ROM. Library functions provide an easy-to-use interface for the LP3500. Software drivers for digital and analog I/O, and for serial com- munication are included with Dynamic C. Web-based technical support is included at no extra charge. Starting with Dynamic C version 9.60, Dynamic C includes the popular µC/OS-II real- time operating system, point-to-point protocol (PPP), FAT file system, RabbitWeb, and other select libraries. Rabbit also offers for purchase the Rabbit Embedded Security Pack featuring the Secure Sockets Layer (SSL) and a specific Advanced Encryption Standard (AES) library. In addition to the Web-based technical support included at no extra charge, a one-year telephone-based technical support subscription is also available for purchase. Visit our Web site at www.rabbit.com for further information and complete documentation. User’s Manual 5 1.5 CE Compliance Equipment is generally divided into two classes. CLASS A CLASS B Digital equipment meant for light industrial use Digital equipment meant for home use Less restrictive emissions requirement: More restrictive emissions requirement: less than 40 dB µV/m at 10 m 30 dB µV/m at 10 m or 100 µV/m (40 dB relative to 1 µV/m) or 300 µV/m These limits apply over the range of 30–230 MHz. The limits are 7 dB higher for frequencies above 230 MHz. Although the test range goes to 1 GHz, the emissions from Rabbit-based systems at frequencies above 300 MHz are generally well below background noise levels. The LP3500 has been tested and was found to be in conformity with the following applicable immunity and emission standards. The LP3510 is also CE qualified as it is a sub-version of the LP3500. Boards that are CE-compliant have the CE mark. NOTE: Earlier versions of the LP3500 sold before 2003 that do not have the CE mark are not CE-complaint. Immunity The LP3500 series of single-board computers meets the following EN55024/1998 immu- nity standards.  EN61000-4-3 (Radiated Immunity)  EN61000-4-4 (EFT)  EN61000-4-6 (Conducted Immunity) Additional shielding or filtering may be required for a heavy industrial environment. Emissions The LP3500 series of single-board computers meets the following emission standards emission standards with the Rabbit 3000 spectrum spreader turned on and set to the nor- mal mode.  EN55022:1998 Class B  FCC Part 15 Class B Your results may vary, depending on your application, so additional shielding or filtering may be needed to maintain the Class B emission qualification. 6 Fox (LP3500) 1.5.1 Design Guidelines Note the following requirements for incorporating the LP3500 series of single-board com- puters into your application to comply with CE requirements. General  The power supply provided with the Tool Kit is for development purposes only. It is the customer’s responsibility to provide a CE-compliant power supply for the end-product application.  When connecting the LP3500 to outdoor cables, the customer is responsible for provid- ing CE-approved surge/lightning protection.  Rabbit recommends placing digital I/O or analog cables that are 3 m or longer in a metal conduit to assist in maintaining CE compliance and to conform to good cable design practices. Rabbit also recommends using properly shielded I/O cables in noisy electromagnetic environments. Safety  For personal safety, all inputs and outputs to and from the LP3500 must not be con- nected to voltages exceeding SELV levels (42.4 V AC peak, or 60 V DC). Damage to the Rabbit 3000 microprocessor may result if voltages outside the design range of 0 V to 40 V DC are applied directly to any of its digital inputs.  The lithium backup battery circuit on the LP3500 has been designed to protect the bat- tery from hazardous conditions such as reverse charging and excessive current flows. Do not disable the safety features of the design. 1.5.2 Interfacing the LP3500 to Other Devices There are two versions of the LCD/keypad module that may be used with the LP3500: without a bezel (Part No. 101-0601), and a remote panel-mounted version with bezel (Part No. 101-0541). The cable used to connect the LCD/keypad module should be less than 30 cm (12") to maintain CE compliance. Appendix C provides complete information for mounting and using the LCD/keypad module. Since the LP3500 series of single-board computers is designed to be connected to other devices, good EMC practices should be followed to ensure compliance. CE compliance is ultimately the responsibility of the integrator. Additional information, tips, and technical assistance are available from your authorized Rabbit distributor, and are also available on our Web site at www.rabbit.com. User’s Manual 7 8 Fox (LP3500) ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� ��� #� ���� ��� ��� ���� ��� ��� #� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� ��� �&’’()* ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� 2. GETTING STARTED Chapter 2 explains how to connect the programming cable and power supply to the LP3500. 2.1 LP3500 Connections 1. Use the 4-40 screws supplied with the Tool Kit to attach the metal standoffs to your LP3500 series board as shown in Figure 2. � ��%�" ��� �� ��� ��� ��� ��� #�� #�� #�� ��� ��� ��� �� ��� ��� #� #�� ��� "� ��� #�� ��� ��� ��� �� ��� ��� ��� �� #�� ��� �� ��� ��� � ��� ��� �� ��� �� �� #�� �� ��� ��� �� ���� !� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� #�� �� ��� �� �� "� ��� ��� ��!�� ��� ��� �� ��� ��� ��� ��� �� � ��� ��� � ��� ������������������� � ������� ���� ���� ������������������������������������������� ����$� ����������� ��� Figure 2. Attach Stand-Offs and Remove Battery Cap User’s Manual 9 ��� � ��!�%�" �� ��� �� � ��� ���������������������������������������������������������������� ��� ��� ��� ��� ��� ��� ��� #� ��� ��� ��� ��� ��� �� ��� ��� �� �� �� ��� ��� �� ��� �� �� ��� �� ��� �� �� �� ��� ��� � �� �� �� ������������������������������������������������������������������������������������������������������������������������������������������������������������������ 2. Attach the LP3500 main board to the Prototyping Board as shown in Figure 3. Press the pins from the headers on the bottom side of the LP3500 board firmly into the corresponding header sockets located at J1, J2, and J4 on the Prototyping Board. NOTE: It is important that you line up the header pins on the LP3500 exactly with the corresponding header sockets J1, J2, and J4 on the Prototyping Board. The header pins may become bent or damaged if the pin alignment is offset, and the LP3500 will not work. Permanent electrical damage may also result if a misaligned LP3500 is powered up. (����� ��� �� ��� ��� ��� ��� ������!"��� �� #���� ��� ��� �� �� �� �� � �� �� �� � �������� ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ � Figure 3. Attach LP3500 Main Board to Prototyping Board 10 Fox (LP3500) ��� �!���������!��������!�������!� � �� �� �� !� !� !� !� ����������������������������������������������������������������������������������������������������������������������������������������������� ��� ��� ��� ��� ��� #� #�� ��� #� �� ��� ��� ���� ��� #�� #� �� �� ���� ��� ��� �� ��� ���� ��� ����� ���� ��� ��� ��� ��� #�� ��� ��� ��� ��� �� �� �� ��� ��� �� ��� ��� ��� !� �� �� ��� ��� #�� ��� �� �� #�� �� ��!�� ��� ��� ��� �� ��� �� ��� ��� +��!�� ��� ��� ��� ������� ���� ��� ��� ��� ��� ��� ��� ��� #� ��� ��� ��� ��� ��� �� ��� ��� �� �� �� ��� ��� �� ��� �� �� ��� �� ��� �� �� �� ��� ��� � �� �� �� ������������������������������������������������������������������������������������������������������������������������������������������������������������������ 3. Connect the programming cable to download programs from your PC and to program and debug the LP3500. NOTE: Use only the programming cable that has a red shrink wrap around the RS-232 level converter (Part No. 101-0513), which is supplied with the LP3500 Tool Kit. Other Rabbit programming cables with clear or blue shrink wrap might not be voltage-com- patible or their connector sizes may be different. Connect the 10-pin PROG connector of the programming cable to header J5 on the LP3500 board. Ensure that the colored edge lines up with pin 1 as shown. There is a small dot on the circuit board next to pin 1 of header J5. (Do not use the DIAG connector, which is used for monitoring only.) Connect the other end of the programming cable to a COM port on your PC. Make a note of the port to which you connect the cable, as Dynamic C will need to have this parameter configured. Note that COM1 on the PC is the default COM port used by Dynamic C. =(&9()� ��3/�5(’<((4 ’:(�%������&49�’:( �- �)-’-’*6348��-&)9 � �������6-)’ ������� ���� ����������� �-0-)(9�(98( ����� ���� �(9 /:)34;�<)&6 ��� ��� ��� ��� ��� ��� ��� �� � �� �� �� �� �� � �������� ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ � � �(,-.(�/0-’�1-.()2 � 34/()’�’&5�34’-�/0-’ �������������� ������������� &������� )#&*��������� &��&��"��� !4&6�6078�34’-�60&1( � � Figure 4. Programming Cable and Power Supply Connections NOTE: Some PCs now come equipped only with a USB port. It may be possible to use an RS-232/USB converter (Part No. 20-151-0178) with the programming cable supplied with the LP3500 Tool Kit. Note that not all RS-232/USB converters work with Dynamic C. User’s Manual 11 ��� �!���������!��������!�������!� ��� ��� ��� ��� ��� #� #� ��� #�� ���� ��� �� ��� ��� �� �� #�� #� ���� ��� �� ��� ��� ���� ��� ����� ���� ��� ��� ��� ��� #�� ��� ��� ��� ��� �� �� �� ��� ��� �� ��� ��� ��� !� �� �� ��� ��� #�� �� ��� �� #�� �� ��� ��!�� ��� ��� �� � �� �� ��� �� ��� �� ��� +��!�� ��� ��� ��� ������� ���� !� !� !� !� ����������������������������������������������������������������������������������������������������������������������������������������������� ���� ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� ��� #� ���� ��� ��� ���� ��� ��� #� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� �&’’()* ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� 4. Connect the power supply. First, prepare the AC adapter for the country where it will be used by selecting the plug. The LP3500 Tool Kit presently includes Canada/Japan/U.S., Australia/N.Z., U.K., and European style plugs. Snap in the top of the plug assembly into the slot at the top of the AC adapter as shown in Figure 4, then press down on the spring-loaded clip below the plug assembly to allow the plug assembly to click into place. Hook up the connector from the wall transformer to header J5 on the Prototyping Board as shown in Figure 4. The orientation of this connector is not important since the VIN (posi- tive) voltage is the middle pin, and GND is available on both ends of the three-pin header J5. NOTE: Do not connect the AC adapter to the VBAT terminal on the Prototyping Board. The VBAT terminal supplies the backup battery voltage of 3 V, and the LP3500 may be damaged if subjected to the raw DC voltage from the AC adapter through the VBAT terminal. 5. Apply power. Plug in the AC adapter. If you are using your own power supply, it must provide 3 V to 30 V DC—voltages outside this range could damage the LP3500. NOTE: A hardware reset may be done by pressing the RESET switch on the LP3500. The LP3500 may also be reset by unplugging the AC adapter, then plugging it back in. However, when the LP3500 is operating in the power-save mode, the backup battery will provide sufficient voltage to prevent a reset from happening, in which case you will have to press the RESET switch on the LP3500. � ��%�" ��� ��� ��� ��� ��� �� ��� ��� #� ��� #� ��� ��� #�� ���� ��� �� �� ��� ���� ��� �� �� ��� #�� #�� #�� ��� #�� #� ��� ��� ���� ��� �� �� ��� ��� ���� ��� ��� ���� ��� ����� #� #�� ��� "� ���� ���� ��� ��� #�� ���� ��� ��� ��� �� �� ��� ���� #�� �� ��� ��� ��� ��� �� ��� ��� ��� �� �� ���� ���� �� #�� ��� ��� �� �� ���� �� ��� � � �� �� ��� ��� ���� ��� �� �� ��� ��� ��� ��� �� �� �� �� �� �� ���� �� �� ��� ��� ��� ��� ���� #�� �� ��� ��� ��� ���� �� ��� ��� ��� �� ���� ��� �� ���� !� �� ��� ��� ��� !� ��� ��� ��� ��� ������ ��� �� ���� ��� ��� ��� ��� #�� ��� #�� ��� �� �� ��� ���� �� #�� �� "� ���� �� ��� ��� ��� ��!�� ��� ��!�� ��!�� �����,� ��� ��� ��� �� ��� ��� ��� ��� �� ���� �� � ����!�� �� �� ��� ��� ��� ��� ��� � ��� ��� +��!�� +��!�� ������������������� ��� ��� ��� ������� � ������� ���� ������� ���� ���� ���� ������������������������������������������� ��� ����������� ��� ���� �$� �$� +$�$*�/<3’1: +$�$*�/<3’1: Figure 5. Locations of LP3500 RESET Switches Reset switches are located on both sides of the LP3500 board. 12 Fox (LP3500) ��� � ��!�%�" �� �� ��� ����� ��� ��� ���� ��� ���� ���� ���� ���� ���� ���� ���� #� ���� ��� ���� ��� ���� ��� ���� ��� ��� ���� ��� ���� ��� ��� ��� ��� ���� �� ��� ��� ��� �� �� ��� �� ��� ���� �� ��� ���� �� ���� ���� �� ��� ���� ���� ��� ��������� �� ���� ���� ��� ���� ���� �� ���� �� �� ���� ��� ��������������������������������������������������������������� ��������� � ��� ��!�����! ���������������������������������������������������������������� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ������������������������������������������������������������������������������������� 2.2 Remove Battery Tab The backup battery on the LP3500 has a plastic tab to protect the battery against discharg- ing before the LP3500 is placed into service. ���� ������� ��� ,- ������������������� ���� ������������������������������������������� ��� ��� ����������� �$� Figure 6. Remove Battery Tab NOTE: Rabbit recommends that the battery tab not be removed until you are ready to place the LP3500 in normal service with regular power connected through header J2. The backup battery protects the contents of the SRAM and keeps the real-time clock running when regular power to the LP3500 is interrupted. If you plan to use the real-time clock functionality in your application, you will need to set the real-time clock once you remove the plastic tab. Set the real-time clock using the onscreen prompts in the demon- stration program. Alternatively, you may set the real-time clock using the SETRTCKB.C sample program from the Dynamic C SAMPLES\RTCLOCK folder. The RTC_TEST.C sample program in the Dynamic C SAMPLES\RTCLOCK folder provides additional exam- ples of how to read and set the real-time clock. User’s Manual 13 ��!�%�" �� ��� �� ��� ���������������������������������������������������������������� 2.3 Installing Dynamic C If you have not yet installed Dynamic C version 7.26P (or a later version), do so now by inserting the Dynamic C CD in your PC’s CD-ROM drive. The CD will auto-install unless you have disabled auto-install on your PC. If the CD does not auto-install, click Start > Run from the Windows Start button and browse for the Dynamic C setup.exe file on your CD drive. Click OK to begin the installation once you have selected the setup.exe file. The Dynamic C User’s Manual provides detailed instructions for the installation of Dynamic C and any future upgrades. NOTE: If you have an earlier version of Dynamic C already installed, the default instal- lation of the later version will be in a different folder, and a separate icon will appear on your desktop. 2.4 Starting Dynamic C Once the LP3500 is connected to your PC and to a power source, start Dynamic C by dou- ble-clicking on the Dynamic C icon on your desktop or in your Start menu. If you are using a USB port to connect your computer to the LP3500, choose Options > Project Options and select “Use USB to Serial Converter” on the Communications tab. Click OK. Dynamic C assumes, by default, that you are using serial port COM1 on your PC when you are running a program. If you are using COM1, then Dynamic C should detect the LP3500 and go through a sequence of steps to cold-boot the LP3500 and to compile the BIOS. If the error message “Rabbit Processor Not Detected” appears, you have probably connected to a different PC serial port such as COM2, COM3, or COM4. You can change the serial port used by Dynamic C with the OPTIONS menu, then try to get Dynamic C to recognize the LP3500 by selecting Reset Target/Compile BIOS on the Compile menu. Try the different COM ports in the OPTIONS menu until you find the one you are con- nected to. If you still can’t get Dynamic C to recognize the target on any port, then the hookup may be wrong or the COM port might not working on your PC. Dynamic C automatically uses a maximum debug baud rate of 38,400 bps when an LP3500 series board is in use. 14 Fox (LP3500) 2.5 PONG.C You are now ready to test your set-up by running a sample program. Find the file PONG.C, which is in the Dynamic C SAMPLES folder. To run the program, open it with the File menu (if it is not still open), then compile and run it by pressing F9 or by selecting Run in the Run menu. The STDIO window will open and will display a small square bouncing around in a box. This program shows that the CPU is working. 2.6 Where Do I Go From Here? NOTE: If you purchased your LP3500 through a distributor or Rabbit partner, contact the distributor or partner first for technical support. If there are any problems at this point:  Use the Dynamic C Help menu to get further assistance with Dynamic C.  Check the Rabbit Technical Bulletin Board and forums at www.rabbit.com/support/bb/ and at www.rabbit.com/forums/.  Use the Technical Support e-mail form at www.rabbit.com/support/. If the sample program ran fine, you are now ready to go on to explore other LP3500 fea- tures and develop your own applications. Chapter 3, “Subsystems,” provides a description of the LP3500’s features, Chapter 4, “Software,” describes the Dynamic C software libraries and introduces some sample pro- grams. These sample programs can be used as templates for applications you may wish to develop. User’s Manual 15 16 Fox (LP3500) 3. SUBSYSTEMS Chapter 3 describes the principal subsystems for the LP3500. • Power Modes •Digital I/O • Serial Communication • A/D Converter Inputs (LP3500 only) • PWM Outputs • Relay Output Circuit (LP3500 only) • Memory Figure 7 shows these Rabbit-based subsystems designed into the LP3500. ���2������2 ��2���� ���� (����� &����� ������ &����’��� ��2���� ��,� � !"��#$ ��%#$ 1������ ��� ��� ��,�-. ����+ ���� +&##�* 1����� ���� ����� �)� ���/����� &����’��� ������� �� �0� (��)*�+��� ������� ������ 1������ Figure 7. LP3500 Subsystems User’s Manual 17 � ��%�" !� ��!�� ������� ���� ��� 3.1 LP3500 Pinouts The LP3500 pinouts are shown in Figure 8. /������ ��"��� ,� ����������������������������������������������������������������� ���� � �� ��� ,0 ,- ���� � �� ��� ���� �� ��� � �� ���� � ��� &����� ���� � �� ���+��! +��-�- ��"��� ���� � �� ���+��! ���� � �� ��� ���� �� ��� � �� ��� � ��� ���� �� �� ��� �23 ���� �� �� �!>���� +��01� ���"��� ���� �� �� �!>���� ��� �� ��� �� . �� ������$� �� �� ����� ��� �� �� ���� ��� �� �� ���� ��""�! ��� �� � ���� � ���� � ���� /������ ,� � ���� � ���� ���"��� � ���� ����������� ������ � ���� ���� � ���� ,4 � ��� ����� ��� ,1 /��"��!������ ��� ,5 ��!�%�" �� ��� �� +���! ���"��� Figure 8. LP3500 Pinouts NOTE: Although header J2 is installed on the LP3510, the associated analog I/O are not available on the LP3510. The relay screw-terminal header at J8 is also not installed on the LP3510. The power supply inputs on header J2 are still available. 3.1.1 Headers and Screw Terminals Standard LP3500 models are equipped with two 1 × 17 headers (J1 and J2) with a pitch of 0.1", one 1 × 25 header (J4) with a pitch of 0.1", and one 1 × 3 screw terminal strip (J8). The Display Interface (J9) is a 2 × 13 header with a pitch of 0.1", and the Serial Interface is a 2 mm 2 × 5 socket. A variety of commercially available connectors with a 0.1" pitch can be used to interface to the signals on headers J1, J2, and J4, or the Prototyping Board may be used to access these signals via screw-terminal headers. 18 Fox (LP3500) ���� ���� ���� ���� ���� ���� ���� ���� ��� ���� ���� ���� ���� ���� ���� ���� ���� �� ��� �� ��� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� �&’’()* 3.2 Power Modes See note User’s Manual 19 Table 2. Software-Defined Power Modes Supports Clock Debug Code Supports Typical Current Mode Power Source Subsystems Frequency Capability Restrictions Relay Output Consumption from Table 3 1 7.3728 MHz 16 mA 2 3.6864 MHz Normal Normal 3 1.8423 MHz Modes 4 1.2288 MHz 5 mA 5 0.9216 MHz None VIN Yes Yes 6 32.768 kHz 1.0 mA 7 16.384 kHz Low- 8 Power 8.192 kHz Modes None 9 4.096 kHz 140 µA 10 2.048 kHz VIN or external 140 µA See battery Section 3.2.1 Power-Save Mode 2.048 kHz No No External battery and (with linear regu- 70 µA Section 3.2.2 lator turned off) SRAM and Onboard battery Processor halted None No No 46 µA RTC updates or ext. battery NOTE: The actual current consumption depends heavily on the SRAM writes in the user’s program. See Section 3.2.2 for more information. Table 2 lists the power modes based on clock frequency that can be defined in software using the powerMode function. The LP3500 can operate at various power levels, depending on the clock frequency and on which subsystems on the board are turned off using the devPowerSet function. Table 3 lists the LP3500 subsystems that can be turned off with the devPowerSet function. Table 3. LP3500 Subsystems That Can Be Turned Off LP3500 Section Description RS-232 Receivers and transmitters are disabled, RxE remains active. RS-485 Transmitter is disabled. A/D Converter ADS7870 internal oscillator is turned off. (LP3500 model only) LCD/Keypad Module LCD/keypad module is turned off. All of the Above All sections are disabled as described above. NOTE: RxE always remains active when the above systems are turned off to allow the LP3500 to “listen” while it is in the power-save mode. The LP3500 processor turns off automatically when VIN is removed, and the processor will not operate again until VIN is restored. The onboard battery provides backup for the SRAM and the real-time clock. VIN must be applied to the LP3500 in order to run or set the processor in any of the numbered modes listed in Table 2. 3.2.1 Setting the Power-Save Mode The LP3500 can be placed in the power-save mode using one of three different software calls, serCommAlert, timedAlert, or digInAlert, depending on whether you wish to use Serial Port E, a simple timeout, or a digital input to trigger the LP3500 to resume operation in one of the other power modes. If you call serCommAlert, then any activity on Serial Port E will trigger the LP3500 out of the low-power mode. If you call timedAlert, then the LP3500 is triggered out of the power-save mode when the specified time has elapsed. If you call digInAlert, then the LP3500 is triggered out of the power-save mode when the specified channel is activated. In addition, digInAlert and serCommAlert have “backup” timeout parameters associ- ated with them to wake up the LP3500 after a specified period even in the absence of the digital or serial triggers. 20 Fox (LP3500) 3.2.2 Operating in the Power-Save Mode VIN may be removed to allow the LP3500 to operate using the external battery once the LP3500 is in Mode 10. At this point, the LP3500 will draw 200 µA after the subsystems listed in Table 3 are turned off. The LP3500’s linear regulator may then be turned off using the setpowersource function call, and this will lower the current draw to 100 µA. The LP3500 digital I/O can continue to operate (remember that an independent +K source is required for the digital outputs) using special software routines. Here are some tips for when the LP3500 is in the power-save mode. 1. Do not write to the SRAM while the LP3500 is in power-save mode and you are relying solely on the onboard backup battery. 2. When the linear regulator is turned off, watch your current consumption carefully since too high a current draw could trigger a system reset and turn off the processor. 3.2.3 Resuming Normal-Power or Low-Power Operation As long as VIN is still connected and the linear regulator has not been turned off, the LP3500 will return automatically to the previous power mode once the non-zero timeout specified in serCommAlert, timedAlert, or digInAlert has elapsed. NOTE: The processor will turn off if VIN is not available at the expiration of the timeout or if VIN is not available when a wake-up signal comes in through Serial Port E or the selected digital input. When the timeout is set to 0, which corresponds to an indefinite timeout, the LP3500 may still be restored to a normal power mode from the power-save mode. 1. Make sure that raw DC power is available at VIN. 2. Turn the linear regulator back on using the setpowersource function call. 3. Use the rdPowerState function call to establish that the LP3500 is now operating from VIN. Note that this function only works with LP3500 models, which have the A/D converter. 4. Use the powerMode function call to set the desired power mode. User’s Manual 21 3.3 Digital I/O 3.3.1 Digital Inputs The LP3500 has 16 digital inputs, IN00–IN15. The inputs are factory-configured to be pulled up to +K in banks of eight, but they can also be pulled up to Vcc or down to 0 V in banks of eight by changing a surface-mounted 0 Ω resistor as shown in Figure 9. �11 6�����! �� /� ���� ��� ���;� ����;� 4 ������� 333 ����4? �������������� ��� Figure 9. LP3500 Digital Inputs [Pulled Up—Factory Default] The digital inputs are each fully protected over a range of 0 V to +36 V, and can handle 7�����������’��� (����� short spikes of ±40 V. The actual switching �"�8�� threshold is approximately 1.40 V. Any- ����� �"�8�� ����� thing below this value is a logic 0, and any- thing above is a logic 1. ��@��� Pulling the digital inputs to Vcc will increase the current consumption by about 300 µA for each digital input. ����� �"�8�� Figure 10. LP3500 Digital Input Protected Range 22 Fox (LP3500) /���������"���)������ 3.3.2 Digital Outputs The LP3500 has 10 digital outputs: OUT0–OUT7 can each sink up to 200 mA, and OUT8–OUT9 can each source up to 200 mA at 36 V. Figure 11 shows a wiring diagram for using the digital outputs in a sinking or a souring configuration. ��7.�7���%*�%*����%*�9�%*:� � ������� 6��� ���� ��%+��7���%*�%*����%*19�%*5� � �11 ������� 6��� Figure 11. LP3500 Digital Outputs TIP: Turn the outputs off (high for sourcing outputs and low for sinking outputs) to reduce current consumption. User’s Manual 23 ��� ��� When the LP3500 is connected to the Proto- typing Board, a 0 Ω resistor on the Prototyp- ing Board (R1) ties +K to VIN, the raw DC input voltage. Figure 12 shows the location of �� this 0 Ω resistor on the Prototyping Board. �� NOTE: R1 on the Prototyping Broad �� �� must be removed to avoid damage to the power supplies if you are using the ��������������������������������������������������������������� � Prototyping Board with the LP3500 and you are using separate power sup- Figure 12. Location of R1 plies for VIN and K. on Prototyping Board When the LP3500 is used alone, remember to connect a power supply to +K (pin 12 on header J7). Your +K supply may be up to +36 V DC, and should be capable of delivering up to 2.0 A. NOTE: If +K is not connected, the digital inputs may float, which may increase your cur- rent consumption. 24 Fox (LP3500) ��� �!���������!��������!�������!� 3.4 Serial Communication The LP3500 has three RS-232 serial ports that can set using the serMode software function call as one RS-232 serial channel (with RTS/CTS) and one 3-wire channel, or they may be set as three RS-232 (3-wire) channels. Table 4 summarizes the options. Table 4. RS-232 Serial Communication Configurations Serial Port serMode B C E 0 RS-232, 3-wire RS-232, 3-wire RS-232, 3-wire 1 RS-232, 5-wire CTS/RTS RS-232, 3-wire The LP3500 also has one RS-485 serial channel (Serial Port F), one CMOS-level serial interface port (Serial Port D), and one CMOS-level serial channel that serves as the pro- gramming port (Serial Port A). All six serial ports operate in an asynchronous mode. An asynchronous port can handle 7 or 8 data bits. A 9th bit address scheme, where an additional bit is sent to mark the first byte of a message, is also supported. Serial Port D and Serial Port A, the programming port, can be operated alternately in the clocked serial mode. In this mode, a clock line syn- chronously clocks the data in or out. Either of the two communicating devices can supply the clock. The LP3500 uses a 3.6864 MHz crystal, which is doubled to 7.3728 MHz. At this frequency, the LP3500 supports standard asynchronous baud rates up to a maximum of 921,600 bps. Table 5 lists the use and the capabilities of the six serial ports. Table 5. LP3500 Serial Port Uses and Capabilities Header Synchronous Serial Port Use Location Capability Programming port or logic-level A J5 Yes serial port B 3-wire RS-232 J4 No 3-wire RS-232 or RTS/CTS flow C J4 No control for Serial Port B Serial interface port supports SPI D device, also used by A/D converter J6 Yes on LP3500 E RS-232 J4 No F RS-485 J4 No User’s Manual 25 3.4.1 RS-232 The LP3500 RS-232 serial communication is supported by an RS-232 transceiver. This trans- ceiver provides the voltage output, slew rate, and input voltage immunity required to meet the RS-232 serial communication protocol. Basically, the chip translates the Rabbit 3000’s logic-level signals to RS-232 signal levels. Note that the polarity is reversed in an RS-232 circuit so that a +2.8 V output becomes approximately -7 V and 0 V is output as +7 V. The RS-232 transceiver also provides the proper line loading for reliable communication. RS-232 can be used effectively at the LP3500’s maximum baud rate for distances of up to 15 m. Logic-level signals are also possible on Serial Ports B, C, and E by changing the 0 Ω surface-mounted resistor jumper settings at locations JP1–JP6. Serial Port E can be set to “listen” and “wake up” the LP3500 when the unit is in a low- power mode. 3.4.2 RS-485 The LP3500 has one RS-485 serial channel, which is connected to Serial Port F on the Rabbit 3000 through an RS-485 transceiver. The half-duplex communication uses the Rabbit 3000’s PG0 pin to control the transmit enable on the communication line. The RS-485 transceiver used on the LP3500 is only capable of supporting a maximum baud rate of 64,000 bits/s. The LP3500 can be used in an RS-485 multidrop network. Connect the 485+ to 485+ and 485– to 485– using single twisted-pair wires (nonstranded, tinned) as shown in Figure 13. Note that a common ground is recommended. 26 Fox (LP3500) � � ��%�" ��%�" !� !� ��!�� ��!�� �� � �� � � � ������������������� ������������������� � � ������� ������� ���� ���� ���� ���� ������������������������������������������� ��� ����������� ��� ������������������������������������������� ��� ����������� ��� �$� �$� �)-749�)(1-,,(49(9 ,0 �� � ��� � ��� � ���� � ���� �� �� � ���� �� ��!�%�" �� ��� �� ��!�%�" �� ��� �� Figure 13. LP3500 Multidrop Network Zener diodes are used in lieu of termination and bias resistors to minimize power consumption. User’s Manual 27 � � ��� ���������������������������������������������������������������� ��� ���������������������������������������������������������������� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� �&’’()* � ������������������������������������������������������������������������������������� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� �&’’()* � ������������������������������������������������������������������������������������� 3.4.3 Serial Interface Port The LP3500 offers a serial interface port at header J6, a 2 mm 2 × 5 socket. This port may be used to �5 connect serial logic-level devices such as Rabbit’s ���A� �?�A!�!� SF1000 serial flash expansion cards to Serial Port ���A� ���A!?�! ���A� ���A!�$ D on the Rabbit 3000. The PIO_0, PIO_1, PIO_2, �?�A!�� �11 and PF2_SRST signals are not used by the SF1000 ���A!�$ ��� serial flash expansion cards. Figure 14 provides the pinout for the serial interface Figure 14. Serial Interface Port port. (Header J6) Pinout 3.4.4 Programming Port The LP3500’s serial programming port is accessed using header J5. The programming port uses the Rabbit 3000’s Serial Port A for communication. Dynamic C uses the pro- gramming port to download and debug programs. The programming port is also used for the following operations.  Cold-boot the Rabbit 3000 on the LP3500 after a reset.  Remotely download and debug a program over an Ethernet connection using the RabbitLink EG2110.  Fast copy designated portions of flash memory from one Rabbit-based board (the master) to another (the slave) using the Rabbit Cloning Board. In addition to Serial Port A, the Rabbit 3000 startup-mode (SMODE0, SMODE1), status, and reset pins are available on the programming port. The two startup mode pins determine what happens after a reset—the Rabbit 3000 is either cold-booted or the program begins executing at address 0x0000. The status pin is used by Dynamic C to determine whether a Rabbit microprocessor is present. The status output has three different programmable functions: 1. It can be driven low on the first op code fetch cycle. 2. It can be driven low during an interrupt acknowledge cycle. 3. It can also serve as a general-purpose CMOS output. The /RESET_IN pin is an external input that is used to reset the Rabbit 3000 and the LP3500 onboard peripheral circuits. The serial programming port can be used to force a hard reset on the LP3500 by asserting the /RESET_IN signal. 28 Fox (LP3500) Alternate Uses of the Serial Programming Port All three clocked Serial Port A signals are available as  a synchronous serial port  an asynchronous serial port, with the clock line usable as a general CMOS input The programming port may also be used as a serial port once the application is running. The SMODE pins may then be used as inputs and the status pin may be used as an output. Refer to the Rabbit 3000 Microprocessor User’s Manual for more information. User’s Manual 29 3.5 Display Interface The LP3500 supports an interface with the parallel ports on the Rabbit 3000 via the Display Interface at header �6 J9. The Display Interface may be used with Rabbit’s �?�� �?�� LCD/keypad module, which offers an operator interface �?�� �?�� �?�� �?�� with seven keys and a 122 × 32 graphic display. �?�� �?�� �?�� �?�� Figure 15 provides the pinout for the Display Interface. �?�� �?�� ��� ��� Appendix C, “LCD/Keypad Module,” provides further ��� %��� information on the LCD/keypad module. %��� %��� %��� %��� %��� %��� ���!� ��!� ���!� ���!� Figure 15. Display Interface (Header J9) Pinout 30 Fox (LP3500) 3.6 A/D Converter Inputs (LP3500 only) The single 8-channel A/D converter chip used in the LP3500 (the LP3510 does not have analog capabilities) has a resolution of 12 bits for differential measurements or 11 bits for single-ended measurements. Four of the channels can be jumpered individually for 4–20 mA using jumpers across pins on header J3, and all 8 channels can be used over several software-scaled voltage ranges. The A/D converter chip has an internal amplifier that works with the resistor divider net- work on the analog inputs as shown in Figure 16. ��� � �� ���� ���� ����;� ��� ��@��;� ,��"���"������ � ��� ������ �� 09-���& ����6? ����� ���� Figure 16. Buffered A/D Converter Inputs The A/D converter chip can be programmed in software to operate over the voltage ranges shown in Table 6. Table 6. A/D Converter Input Ranges Voltage Gain Code Multiplier Range 0 1 0–20 V 1 2 0–10 V 2 4 0–5 V 3 5 0–4 V 4 8 0–2.5 V 5 10 0–2 V 6 16 0–1.25 V 7 20 0–1 V User’s Manual 31 Single-ended measurements are made by connecting the analog signal between an analog input channel (AIN0–AIN7) and AGND. Differential measurements are made by connect- ing a pair of differential analog signals to an adjacent pair of analog input channels (AIN0–AIN1, …, AIN6–AIN7). The A/D converter is only capable of converting positive voltages, and so will convert the difference between an adjacent pair of input channels, and must be scaled for a voltage range appropriate for the voltage differences. Table 7 lists the jumper configurations for header J3 used to set the 4–20 mA and the volt- age measurement options. Table 7. Header J3 Configuration for Analog I/O Options Voltage Option Analog Input Channel 4–20 mA Option (Factory Default) AIN0 Jumper “parked” on pin 2 Pins 1–2 connected AIN1 Jumper “parked” on pin 4 Pins 3–4 connected AIN2 Jumper “parked” on pin 6 Pins 5–6 connected AIN3 Jumper “parked” on pin 8 Pins 7–8 connected CAUTION: If you have enabled the 4–20 mA current option on any of the AIN0–AIN3 channels, be careful with any voltage sources that you might connect to these inputs. The voltage must be less than 2.5 V to keep the current across the 100 Ω resistor below the maximum allowed current. The A/D converter inputs are factory-calibrated, and the calibration constants are stored in flash memory. You may calibrate the A/D converter inputs at a later time using the software functions described in Section 4.4.5, “A/D Converter Inputs.” NOTE: If you are using a fixed voltage range, you should recalibrate your LP3500 at that range. AIN7 can be used to monitor Vcc using the VccMonitorInit function. While Vcc can be monitored in all the power modes, Vcc monitoring is particularly useful when the LP3500 is being operated from an external battery to monitor the voltage being supplied by the battery. The VccMonitorInit function requires the operation of the A/D converter, which con- sumes about 500 µA. The Vcc monitoring circuit itself consumes about 15 µA while it is engaged. Turn off VccMonitorInit() (and the A/D converter if it is not going to be used) when the test is done to extend your battery life. 32 Fox (LP3500) 3.7 PWM Outputs The D/A conversion outputs are pulse-width modulated and scaled to provide an output from 0 V to Vcc (approx. 2.8 V). Figure 17 shows the PWM outputs. ��;� ���� ���� 4 ������� 333 �������������� ��4? ��� Figure 17. PWM Outputs User’s Manual 33 3.8 Relay Output Circuit (LP3500 only) A bistable relay is stuffed on LP3500 models only at position K1, and the relay contacts are accessed via screw-terminal header J8. The relay can switch up to 1 A at 30 V DC. The relay is set via Parallel Port PG4 on the Rabbit 3000, and is reset via Parallel Port PG5 by a 10 ms pulse. The relay resets when the LP3500 resets, and operates only in the nor- mal power modes. NOTE: The relay does not reset automatically when power is removed from the LP3500. �$* ,1 � � �� > � � ���4? �7� �@��� � � � � ��� � � � 4 ������� 333 �@��� �������������� �7. ���4? �� � > � � �� +$�$* Figure 18. Relay Output Circuit NOTE: Switching the relay may consume up to 120 mA during the roughly 10 ms that it takes for the relay to switch. Make sure that your power supply has sufficient capacity to handle this surge current to avoid putting the LP3500 into the power-save mode. The relay does not consume any current while it is in the NO or the NC position and is not switching. 34 Fox (LP3500) ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� ��� #� ���� ��� ��� ���� ��� ��� #� ��� ���� ��� ��� ��� ���� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� �&’’()* ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� ��� #� ���� ��� ��� ���� ��� ��� ��� #� ���� ��� ��� ��� ���� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� �&’’()*��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� 3.9 Serial Programming Cable The programming cable is used to connect the LP3500’s serial programming port to a PC serial COM port. The programming cable converts the RS-232 voltage levels used by the PC serial port to the CMOS voltage levels used by the Rabbit 3000. When the PROG connector on the programming cable is connected to the LP3500’s serial programming port at header J5, programs can be downloaded and debugged over the serial interface. The DIAG connector of the programming cable may be used on header J5 of the LP3500 with the LP3500 operating in the Run Mode. This allows the programming port to be used as a regular serial port. 3.9.1 Changing Between Program Mode and Run Mode The LP3500 is automatically in Program Mode when the PROG connector on the pro- gramming cable is attached, and is automatically in Run Mode when no programming cable is attached. When the Rabbit 3000 is reset, the operating mode is determined by the state of the SMODE pins. When the programming cable’s PROG connector is attached, the SMODE pins are pulled high, placing the Rabbit 3000 in the Program Mode. When the programming cable’s PROG connector is not attached, the SMODE pins are pulled low, causing the Rabbit 3000 to operate in the Run Mode. See Figure 19. ��������3��� +���3��� � ��%�" � ��%�" ��� �� ��� �� ��� ��� ��� ��� ��� ��� ��� #�� #�� #�� ��� #�� #�� #�� ��� ��� ��� ��� ��� ��� �� �� ��� ��� ��� #� #�� ��� ��� #� #�� "� "� ��� ��� #�� ��� #�� ��� ��� ��� ��� ��� ��� ��� �� �� ��� ��� �� ��� ��� ��� �� #�� ��� #�� ��� ��� ��� �� ��� � �� ��� � ��� ��� ��� ��� ��� ��� �� �� �� �� �� �� #�� #�� �� ��� �� ��� ��� �� ���� ��� �� ���� ��� ��� !� !� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� #�� ��� #�� �� �� ��� ��� �� �� "� "� �� ��� �� ��� ��!�� ��� ��� ��� ��!�� ��� ��� �� ��� �� ��� ��� ��� ��� ��� ��� ��� ��� �� � � �� � � ��� ��� ��� ��� ��� ��� ������������������� ���� ������������������� � ������� � ������� ���� ���� ���� ������������������������������������������� ��� ����������� ��� ������������������������������������������� ������������������ ��� �$� �$� ���� +$�$* ��8�� ��8�� ����������� /<3’1: ����� �-0-)(9�(98( �- �������6-)’ �9�9��(� .33�8��������2��2�����: ���������!�����������1� ������������������� �’��������/��2������������2����2������2������! Figure 19. LP3500 Program Mode and Run Mode Set-Up User’s Manual 35 ��� � ��!�%�" �� ��� �� ��� � ��!�%�" �� ��� �� � � ��� ���������������������������������������������������������������� ��� ���������������������������������������������������������������� A program “runs” in either mode, but can only be downloaded and debugged when the LP3500 is in the Program Mode. Refer to the Rabbit 3000 Microprocessor User’s Manual for more information on the pro- gramming port and the programming cable. 3.9.2 Standalone Operation of the LP3500 The LP3500 must be programmed via the Prototyping Board or via a similar arrangement on a customer-supplied board. Once the LP3500 has been programmed successfully, remove the serial programming cable from the programming connector and reset the LP3500. The LP3500 may be reset by cycling the power off/on or by pressing the RESET button on the Prototyping Board. The LP3500 module may now be removed from the Pro- totyping Board for end-use installation. CAUTION: Disconnect power to the Prototyping Board or other boards when removing or installing your LP3500 to protect against inadvertent shorts across the pins or dam- age to the LP3500 if the pins are not plugged in correctly. Do not reapply power until you have verified that the LP3500 is plugged in correctly. 3.10 Other Hardware 3.10.1 Spectrum Spreader The Rabbit 3000 features a spectrum spreader, which helps to mitigate EMI problems. By default, the spectrum spreader is on automatically, but it may also be turned off or set to a stronger setting. The means for doing so is through a simple global macro as shown below. 1. Select the “Defines” tab from the Dynamic C Options > Project Options menu. 2. Normal spreading is the default, and usually no entry is needed. If you need to specify normal spreading, add the line ENABLE_SPREADER=1 For strong spreading, add the line ENABLE_SPREADER=2 To disable the spectrum spreader, add the line ENABLE_SPREADER=0 NOTE: The strong spectrum-spreading setting is not recommended since it may limit the maximum clock speed or the maximum baud rate. It is unlikely that the strong set- ting will be used in a real application. 3. Click OK to save the macro. The spectrum spreader will now be set to the state specified by the macro value whenever you are in the project file where you defined the macro. NOTE: Refer to the Rabbit 3000 Microprocessor User’s Manual for more information on the spectrum-spreading setting and the maximum clock speed. 36 Fox (LP3500) 3.11 Memory 3.11.1 SRAM The LP3500 module is designed to accept 128K to 512K of SRAM at U5. The standard LP3500 modules come with 512K of SRAM. 3.11.2 Flash Memory The LP3500 is also designed to accept 256K to 512K of flash memory at U6 and U7. The standard LP3500 modules comes with two 256K flash memory chips. NOTE: Rabbit recommends that any customer applications should not be constrained by the sector size of the flash memory since it may be necessary to change the sector size in the future. A Flash Memory Bank Select jumper configuration option based on 0 Ω surface-mounted resistors exists at header JP10. This option, used in conjunction with some configuration macros, allows Dynamic C to compile two different co-resident programs for the upper and lower halves of the 256K flash in such a way that both programs start at logical address 0000. This is useful for applications that require a resident download manager and a separate downloaded program. See Rabbit’s Technical Note 218, Implementing a Serial Download Manager for a 256K Flash, in the online documentation for details. User’s Manual 37 38 Fox (LP3500) 4. SOFTWARE Dynamic C is an integrated development system for writing embedded software. It runs on an IBM-compatible PC and is designed for use with single-board computers and other devices based on the Rabbit microprocessor. Chapter 4 provides the libraries, function calls, and sample pro- grams related to the LP3500. You have a choice of doing your software development in the flash memory or in the static RAM included on the LP3500. The flash memory and SRAM options are selected with the Options > Project Options > Compiler menu. The advantage of working in RAM is to save wear on the flash memory, which is limited to about 100,000 write cycles. The disadvantage is that the code and data might not both fit in RAM. NOTE: An application can be developed in RAM, but cannot run standalone from RAM after the programming cable is disconnected. All standalone applications can only run from flash memory. NOTE: Do not depend on the flash memory sector size or type. Due to the volatility of the flash memory market, the LP3500 and Dynamic C were designed to accommodate flash devices with various sector sizes. Developing software with Dynamic C is simple. Users can write, compile, and test C and assembly code without leaving the Dynamic C development environment. Debugging occurs while the application runs on the target. Alternatively, users can compile a program to an image file for later loading. Dynamic C runs on PCs under Windows 2000/NT and later. ® ® Rabbit’s Technical Note TN257, Running Dynamic C With Windows Vista , in the ® online documentation set provides additional information about using Windows Vista with versions of Dynamic C prior to v. 9.60. Programs can be downloaded at baud rates of up to 460,800 bps after the program compiles. User’s Manual 39 Dynamic C has a number of standard features.  Full-feature source and/or assembly-level debugger, no in-circuit emulator required.  Royalty-free TCP/IP stack with source code and most common protocols.  Hundreds of functions in source-code libraries and sample programs: X Exceptionally fast support for floating-point arithmetic and transcendental functions. X RS-232 and RS-485 serial communication. X Analog and digital I/O drivers. 2 X I C, SPI, GPS, encryption, file system. X LCD display and keypad drivers.  Powerful language extensions for cooperative or preemptive multitasking  Loader utility program to load binary images into Rabbit targets in the absence of Dynamic C.  Provision for customers to create their own source code libraries and augment on-line help by creating “function description” block comments using a special format for library functions.  Standard debugging features: X Breakpoints—Set breakpoints that can disable interrupts. X Single-stepping—Step into or over functions at a source or machine code level, µC/OS-II aware. X Code disassembly—The disassembly window displays addresses, opcodes, mnemonics, and machine cycle times. Switch between debugging at machine-code level and source-code level by simply opening or closing the disassembly window. X Watch expressions—Watch expressions are compiled when defined, so complex expressions including function calls may be placed into watch expressions. Watch expressions can be updated with or without stopping program execution. X Register window—All processor registers and flags are displayed. The contents of general registers may be modified in the window by the user. X Stack window—shows the contents of the top of the stack. X Hex memory dump—displays the contents of memory at any address. X STDIO window—printf outputs to this window and keyboard input on the host PC can be detected for debugging purposes. printf output may also be sent to a serial port or file. 40 Fox (LP3500) 4.1 Upgrading Dynamic C 4.1.1 Patches and Bug Fixes Dynamic C patches that focus on bug fixes are available from time to time. Check the Web site www.rabbit.com/support/ for the latest patches, workarounds, and bug fixes. The default installation of a patch or bug fix is to install the file in a directory (folder) dif- ferent from that of the original Dynamic C installation. Rabbit recommends using a differ- ent directory so that you can verify the operation of the patch without overwriting the existing Dynamic C installation. If you have made any changes to the BIOS or to libraries, or if you have programs in the old directory (folder), make these same changes to the BIOS or libraries in the new directory containing the patch. Do not simply copy over an entire file since you may overwrite a bug fix; of course, you may copy over any programs you have written. Once you are sure the new patch works entirely to your satisfaction, you may retire the existing installation, but keep it available to handle legacy applications. 4.1.2 Extras Dynamic C installations are designed for use with the board they are included with, and are included at no charge as part of our low-cost kits. Starting with Dynamic C version 9.60, Dynamic C includes the popular µC/OS-II real- time operating system, point-to-point protocol (PPP), FAT file system, RabbitWeb, and other select libraries. Rabbit also offers for purchase the Rabbit Embedded Security Pack featuring the Secure Sockets Layer (SSL) and a specific Advanced Encryption Standard (AES) library. In addition to the Web-based technical support included at no extra charge, a one-year telephone-based technical support subscription is also available for purchase. Visit our Web site at www.rabbit.com for further information and complete documentation. User’s Manual 41 4.2 Sample Programs Sample programs are provided in the Dynamic C Samples folder. The sample program PONG.C demonstrates the output to the STDIO window. The various directories in the Samples folder contain specific sample programs that illus- trate the use of the corresponding Dynamic C libraries. The LP3500 folder provides sample programs specific to the LP3500. Each sample pro- gram has comments that describe the purpose and function of the program. Follow the instructions at the beginning of the sample program. To run a sample program, open it with the File menu (if it is not still open), compile it using the Compile menu, and then run it by selecting Run in the Run menu. The LP3500 must be in the Program mode (see Section 3.9, “Serial Programming Cable”) and must be connected to a PC using the programming cable as described in Section 2.1, “LP3500 Connections.” Appendix F, “Running a Sample Program,” takes you through the steps of running one of the sample programs. 4.2.1 Power Modes The following sample program is found in the POWER subdirectory in SAMPLES\LP3500.  POWER.C—This program demonstrates switching from the normal raw DC power source to an external battery using the Prototyping Board. Pressing a switch will change from the power source and will be displayed by flashing LEDs.  LOWPWRDEMO.C—This program demonstrates a low-power mode with the normal power source connected to the LP3500. 4.2.2 Digital I/O The following sample programs are found in the IO subdirectory in SAMPLES\LP3500.  DIGIN.C—Demonstrates the use of the digital inputs. Using the Prototyping Board, you can see an input channel toggle from HIGH to LOW when pressing a pushbutton on the Prototyping Board.  DIGOUT.C—Demonstrates the use of the high-current outputs configured as either sink- ing or sourcing outputs. Using the Prototyping Board, you can see an LED toggle on/off via a high-current output.  DIGBANKIN.C—Demonstrates the use of the digital inputs. Using the Prototyping Board, you can see a bank of input channels toggle from HIGH to LOW when pressing a pushbutton on the Prototyping Board.  DIGBANKOUT.C—Demonstrates the use of the high-current outputs configured as either sinking or sourcing outputs. Using the Prototyping Board, you can see a bank of chan- nels toggle the corresponding LEDs on/off via high-current outputs. 42 Fox (LP3500) 4.2.3 Serial Communication The following sample programs are found in the RS232 subdirectory in SAMPLES\LP3500.  SIMPLE3WIRE.C—This program demonstrates basic initialization for a simple RS-232 3-wire loopback displayed in the STDIO window. The following sample programs are found in the RS485 subdirectory in SAMPLES\LP3500.  SIMPLE485MASTER.C—This program demonstrates a simple RS-485 transmission of lower case letters to a slave LP3500. The slave will send back converted upper case let- ters back to the master LP3500 and display them in the STDIO window. Use SIMPLE485SLAVE.C to program the slave LP3500.  SIMPLE485SLAVE.C—This program demonstrates a simple RS-485 transmission of lower case letters to a slave LP3500. The slave will send back converted upper case let- ters back to the master LP3500 and display them in the STDIO window. Use SIMPLE485MASTER.C to program the master LP3500. 4.2.4 A/D Converter Inputs The following sample programs are found in the ADC subdirectory in SAMPLES\LP3500.  AD_RDVOLT_ALL.C—This program reads and displays the voltage and equivalent values of each single-ended A/D converter channel. Coefficients are read from the A/D con- verter's simulated EEPROM in flash memory to compute the equivalent voltages. Com- puted raw data and equivalent voltages are displayed in the STDIO window.  AD_RDVOLT_CH.C—This program reads and displays the voltage and equivalent values of one single-ended A/D converter channel. Coefficients are read from the A/D con- verter's simulated EEPROM in flash memory to compute the equivalent voltages. Com- puted raw data and equivalent voltages are displayed in the STDIO window.  AD_RDDIFF_CH.C—This program demonstrates reading one differential A/D converter channel. Coefficients are read from the A/D converter's simulated EEPROM in flash memory to compute the equivalent voltages. Computed raw data and equivalent volt- ages are displayed in the STDIO window.  AD_RDMA_CH.C—This program demonstrates reading one milliampere A/D converter channel. Coefficients are read from the A/D converter's simulated EEPROM in flash memory to compute the equivalent currents. Computed raw data and equivalent cur- rents are displayed in the STDIO window.  AD_SAMPLE.C—This program demonstrates how to use the A/D low-level driver. The program will display the average voltage that is present on an A/D converter channel. The particular channel and the number of samples may be changed by the user. User’s Manual 43 4.2.5 PWM Outputs The following sample program is found in the IO subdirectory in SAMPLES\LP3500.  PWMOUT.C—This program demonstrates the PWM functions. It will set the PWM chan- nels, PWM0–PWM2, to the following duty cycles: PWM Channel 0 to 10% PWM Channel 1 to 25% PWM Channel 2 to 50% All activity will be displayed in the STDIO window. 4.2.6 Relay Output The following sample program is found in the RELAY subdirectory in SAMPLES\LP3500.  SWRELAY.C—This program demonstrates the relay-switching function call operating on normal power source. Use the pushbutton switches on the Prototyping Board to switch the relay between the SET (NO) and RESET (NC) positions. All activity will be dis- played with the LEDs. 4.2.7 Vcc Monitoring The following sample program is found in the POWER subdirectory in SAMPLES\LP3500.  VCCMONITOR.C—This program demonstrates the Vcc monitoring function on AIN7. All activity will be displayed in the STDIO window 4.2.8 LP3500 Calibration The following sample programs are found in the ADC subdirectory in SAMPLES\LP3500.  AD_CAL_ALL.C—This program demonstrates how to recalibrate all single-ended A/D converter channels using two known voltages to generate constants for each channel, and will be written into the user block data area. The program uses the STDIO window to display the voltage that is being monitored. NOTE: This sample program will overwrite the calibration constants set at the factory.  AD_CAL_CHAN.C—This program demonstrates how to recalibrate one single-ended A/D converter channel using two known voltages to generate constants for each channel, and will be written into the user block data area. The program uses the STDIO window to display the voltage that is being monitored. NOTE: This sample program will overwrite the calibration constants set at the factory.  AD_CALDIFF_CH.C—This sample program demonstrates how to recalibrate one differ- ential A/D converter channel using two known voltages to generate constants for that channel and rewrite the constants into the user block data area. The program uses the STDIO window to display the voltage that is being monitored. NOTE: This sample program will overwrite the calibration constants set at the factory. 44 Fox (LP3500)  AD_CALMA_CH.C—This sample program demonstrates how to recalibrate one A/D con- verter channel operating in the 4–20 mA current mode using two known currents to generate two coefficients, gain and offset, which are rewritten into the user block data area. The program uses the STDIO window to display the current that is being moni- tored. NOTE: This sample program will overwrite the calibration constants set at the factory. 4.2.9 LCD/Keypad Module Sample Programs Sample programs for the LCD/keypad module are described in Section C.8. User’s Manual 45 4.3 LP3500 Libraries One library directory provides the function calls that are used to develop applications for the LP3500.  LP3500—libraries associated with features specific to the LP3500. The functions in the LIB\Rabbit3000\LP35xx.LIB library are described in Section 4.4, “LP3500 Function Calls.” The LCD/keypad module functions are described in Section C.7. Other generic functions applicable to all devices based on the Rabbit 3000 microprocessor are described in the Dynamic C Function Reference Manual. 46 Fox (LP3500) 4.4 LP3500 Function Calls 4.4.1 LP3500 Power Modes int devPowerSet(int devices, int state); Sets individual devices to low-power or fully active states in the order listed below. PARAMETERS devices is a list of the following macros, which are OR'ed together, that will be affected by the state parameter, e.g., RS232DEV|ADCDEV. RS232DEV—RS-232 devices RS485DEV—RS-485 devices ADCDEV—ADS7870 A/D converter devices DISPDEV—LCD/keypad module ALLDEVICES—all devices state 0 = shuts or powers down listed devices 1 = activates listed devices Macro Description state = 0 state after Board Initialization Receivers and transmitters are disabled, RS232DEV 1 RxE remains active RS485DEV Transmitter is disabled 0 ADCDEV ADS7870 internal oscillator is turned off 0 DISPDEV LCD/keypad module is turned off. 0 ALLDEVICES All devices are disabled as described above — Table E-1 provides further information about the power consumption associated with each section. RETURN VALUE 0 if valid parameter -1 otherwise SEE ALSO powerMode, anaInConfig, brdInit User’s Manual 47 int powerMode(int mode); Sets the LP3500 operating power. PARAMETERS mode is the operating mode based on the following macros. Typical Current Debug Mode Description Consumption Capable? 1 CCLK = PCLK = MainOsc = 7.3728 MHz 2 CCLK = PCLK = MainOsc/2 = 3.6864 MHz Yes 3 CCLK = PCLK = MainOsc/4 = 1.8423 MHz 5–16 mA 4 CCLK = PCLK = MainOsc/6 = 1.2288 MHz 5 CCLK = PCLK = MainOsc/8 = 0.9216 MHz 6 CCLK = PCLK = 32.768 kHz 7 CCLK = PCLK = 32.768 kHz/2 = 16.384 kHz No 8 CCLK = PCLK = 32.768 kHz/4 = 8.192 kHz 2 mA 9 CCLK = PCLK = 32.768 kHz/8 = 4.096 kHz 10 CCLK = PCLK = 32.768 kHz/16 = 2.048 kHz NOTE: When using modes 6–10, be sure to call hitwd() explicitly since periodic inter- rupts, which incorporate a virtual watchdog, are disabled in these modes. Table 2 provides more specific information on the LP3500’s capabilities associated with these and other software-defined modes. RETURN VALUE 0 if valid parameter -1 if invalid parameter SEE ALSO devPowerSet, rdPowerState, setPowerState, VccMonitor 48 Fox (LP3500) void serCommAlert(int lowpowermode, int maxpowermode, int powersource, unsigned long timeout); Use this function to poll Serial Port E for any activity or until a timeout occurs. The function call forces the LP3500 to enter the low-power mode using the battery for polling. Upon expiration of the timeout or the receipt of a serial byte, this function will enable the normal power mode and exit. Use devPowerSet(ALLDEVICES, int state) before and after this function call to deactivate and activate all devices to operate at less power. PARAMETERS lowpowermode is the low-power mode setting to enter, usually 10 (see powerMode()) maxpowermode is the maximum operating power mode setting to enter, usually 1 (see power- Mode()) powersource 1 = battery 2 = raw DC power timeout is the timeout in seconds if no activity is detected on the RxE receiver line. Enter 0 for no timeout SEE ALSO powerMode, digInAlert, timedAlert, devPowerSet void timedAlert(int lowpowermode, int maxpowermode, int powersource, unsigned long timeout) Use this function to poll the real-time clock until a timeout occurs. The function call forces the LP3500 to enter the low-power mode, disables the normal power source, and may enable the external battery for polling. Upon expiration of the timeout this function will enable the normal power mode and exit. If the normal power source is not available, the LP3500 will not be able to resume operation at the maximum- power mode, and may reset. Use devPowerSet(ALLDEVICES, int state) before and after this function call to deactivate and activate all devices to operate at less power. PARAMETERS lowpowermode is the low-power mode setting to enter, usually 10 (see powerMode()) maxpowermode is the maximum operating power mode setting to enter, usually 1 (see power- Mode()) powersource 1 = battery 2 = raw DC power timeout is the timeout in seconds if an input is not received. SEE ALSO powerMode, digInAlert, serCommAlert, devPowerSet User’s Manual 49 void digInAlert(int channel, int value, int lowpowermode, int maxpowermode, int powersource, unsigned long timeout) Use this function to poll a selected digital input until a timeout occurs. The function call forces the LP3500 to enter the low-power mode using the battery for polling. Upon activation of the channel or expiration of the timeout, this function will enable the normal power mode and exit. Use devPowerSet(ALLDEVICES, int state) before and after this function call to deactivate and activate all devices to operate at less power. PARAMETERS channel is the digital input channel (IN00– IN15) to poll value is the input value of 0 or 1 to receive lowpowermode is the low-power mode setting to enter, usually 10 (see powerMode()) maxpowermode is the maximum operating power mode setting to enter, usually 1 (see power- Mode()) powersource 1 = battery 2 = raw DC power timeout is the timeout in seconds if an input is not received. Enter 0 for no timeout. SEE ALSO powerMode, serCommAlert, timedAlert, devPowerSet int rdPowerState(void); Determines if the LP3500 is running under battery power or a raw DC power source. RETURN VALUE 0 if on raw DC power source 1 if on battery power SEE ALSO powerMode, setPowerState int setPowerSource(int state); Turns the linear regulator “off” or “on.” PARAMETER 0 for normal power source 1 for battery RETURN VALUE 0 if successful -1 if raw DC power source is not available -2 if battery is not available SEE ALSO powerMode, rdPowerState 50 Fox (LP3500) 4.4.2 Board Initialization void brdInit (void); Call this function at the beginning of your program. This function initializes the system I/O ports and loads all the A/D converter and D/A converter calibration constants from flash memory into SRAM for use by your program. If the LCD/keypad module is installed, this function will turn off LED DS1 to indi- cate that the initialization was successful. Summary of Initialization  LP3500 uses main oscillator  LCD/keypad module buffer is disabled  RS-485 serial communication is not enabled  RS-232 serial communication is enabled  Unused configurable inputs are tied and unused configurable outputs are set low  Self-timed chip select is set to 109 ns  If A/D converter chip is installed, chip is reset and SCLKD is set to 19,200 bps  If A/D converter chip is installed, calibration constants are read  If relay is installed, relay is set to NC or RESET position The ports are initialized according to Table A-3. User’s Manual 51 4.4.3 Digital I/O void digOut(int channel, int value); Sets the state of a digital output (OUT0–OUT9). Remember to call brdInit before executing this function. A runtime error will occur for the following conditions: 1. channel or value out of range. 2. brdInit was not executed before executing digOut. PARAMETERS channel is the output channel number (0–9). value is the output value (0 or 1). SEE ALSO brdInit, digIn, digBankOut void digBankOut(int bank, int value); Writes the state of a block of designated digital output channels. The first bank consists of OUT0– OUT7, the second bank consists of OUT8–OUT9. A run-time error will occur for the following conditions: 1. channel or value out of range. 2. brdInit was not executed before executing digOut. PARAMETER bank is 0 for OUT0–OUT7, 1 for OUT8–OUT9. value is an 8-bit output value, where each bit corresponds to one channel. OUT0 and OUT8 are the least significant bit 0. RETURN VALUE None. SEE ALSO brdInit, digOut, digBankIn 52 Fox (LP3500) int digIn(int channel); Reads the state of an input channel (IN00–IN15). A run-time error will occur for the following conditions: 1. channel out of range. 2. brdInit was not executed before executing digIn. PARAMETER channel is the input channel number (0–15) RETURN VALUE The logic state of the input (0 or 1). SEE ALSO brdInit, digOut, digBankIn void digBankIn(int bank); Reads the state of a block of designated digital input channels. The first bank consists of IN0–IN07, the second bank consists of IN08–IN15. A run-time error will occur for the following conditions: 1. bank out of range. 2. brdInit was not executed before executing digIn. PARAMETER bank is 0 for IN00–IN07, 1 for IN08–IN15. RETURN VALUE An input value in the lower byte, where each bit corresponds to one channel. IN00 and IN08 are in the bit 0 place. SEE ALSO brdInit, digOut, digBankOut User’s Manual 53 4.4.4 Serial Communication Library files included with Dynamic C provide a full range of serial communications sup- port. The LIB\Rabbit3000\RS232.LIB library provides a set of circular-buffer-based serial functions. The LIB\Rabbit3000\PACKET.LIB library provides packet-based serial functions where packets can be delimited by the 9th bit, by transmission gaps, or with user-defined special characters. Both libraries provide blocking functions, which do not return until they are finished transmitting or receiving, and nonblocking functions, which must be called repeatedly until they are finished. For more information, see the Dynamic C User’s Manual and Rabbit’s Technical Note TN213, Rabbit 2000 Serial Port Software. Use the following function calls with the LP3500. int serMode(int mode); User interface to set up LP3500 serial communication lines. Call this function after serXOpen(). Whether you are opening one or multiple serial ports, this function must be executed after executing the last serXOpen function AND before you start using any of the serial ports. This function is non-reentrant. If Mode 1 is selected, CTS/RTS flow control is exercised using the serBflowcontrolOn and serBflowcontrolOff functions from the RS232.LIB library. PARAMETER mode is the defined serial port configuration. Serial Port Mode B C E F 0 RS-232, 3-wire RS-232, 3-wire RS-232, 3-wire RS-485 1 RS-232, 5-wire CTS/RTS RS-232, 3-wire RS-485 RETURN VALUE 0 if valid mode, 1 if not. SEE ALSO ser485Tx, ser485Rx 54 Fox (LP3500) void ser485Tx(void); Enables the RS-485 transmitter. Transmitted data get echo'ed back into the receive data buffer. These echo'ed data could be used to know when to disable the transmitter by using one of the following methods: Byte mode—disable the transmitter after the same byte that is transmitted is detected in the receive data buffer. Block data mode—disable the transmitter after the same number of bytes transmitted is detected in the receive data buffer. serMode() must be executed before running this function. SEE ALSO serMode, ser485Rx void ser485Rx(void); Disables the RS-485 transmitter. This puts the LP3500 in listen mode, which allows it to receive data from the RS-485 interface. serMode() must be executed before running this function. SEE ALSO serMode, ser485Tx NOTE: The RS-485 transceiver used on the LP3500 is only capable of supporting a max- imum baud rate of 64,000 bits/s. The baud rate is set by the Dynamic C _485BAUD macro. For example, add the following line on the Defines tab in the Dynamic C Options > Project Options to set a baud rate of 57,600 bits/s, then click OK. _485BAUD=57600 User’s Manual 55 4.4.5 A/D Converter Inputs The functions in this section apply only to the LP3500 model. unsigned int anaInConfig(unsigned int instructionbyte, unsigned int cmd, long baud); Use this function to configure the ADS7870 A/D converter. This function will address the ADS7870 in Register Mode only, and will report an error if you try to use it in Direct Mode. Refer to ADS7870 spec- ification for proper addressing and commands. ADS7870 Signal ADS7870 State LP3500 Function/State LN0 Input AIN0 LN1 Input AIN1 LN2 Input AIN2 LN3 Input AIN3 LN4 Input AIN4 LN5 Input AIN5 LN6 Input AIN6 LN7 Input AIN7 /RESET Input Board reset device RISE/FALL Input Tied up for SCLK active on rising edge PIO_0 Input Pulled down unless driven by serial interface connection PIO_1 Input Pulled down unless driven by serial interface connection PIO_2 Input Pulled down unless driven by serial interface connection PIO_3 Input Pulled up unless driven by Vcc monitor CONVERT Input Pulled down, not used BUSY Output PF1 pulled down; 1 state converter is busy CCLKCNTRL Input Tied down; 0 state sets CCLK as input CCLK Input Tied down; external conversion clock SCLK Input PF0; serial data transfer clock SDI Input PC0; 3-wire mode for serial data input SDO Output PC1; serial data output /CS driven /CS Input PF3 pulled up; active-low enables serial interface BUFIN Input Tied down; reference buffer amplifier 56 Fox (LP3500) PARAMETERS instructionbyte will initiate a read or write operation at 8 or 16 bits on the designated register address, for example: checkid = anaInConfig(0x5F, 0, 9600); // read ID and set baud rate cmd is the command data that configure the registers addressed by the instruction byte. Enter 0 if per- forming a read operation. i = anaInConfig(0x07, 0x3a, 0); // write ref/osc reg and enable baud is the serial clock transfer rate of 9600 to 57,600 bps. baud must be set on the first call to this function. Enter 0 in this parameter thereafter. anaInConfig(0x00, 0x00, 9600); // resets device and sets baud RETURN VALUE 0 on write operations, data value on read operations. SEE ALSO anaInDriver, anaIn, brdInit User’s Manual 57 unsigned int anaInDriver(unsigned int cmd, unsigned int len); Reads the voltage of an analog input channel by serial-clocking an 8-bit command to the ADS7870 device by its Direct Mode method. The conversion begins as soon as the last data bit is transferred. An exception error will occur if Direct Mode bit D7 is not set. PARAMETER cmd contains a gain code and a channel code as follows. D7—1; D6–D4—Gain Code; D3–D0—Channel Code Use the following calculation and the tables below to determine cmd: cmd = 0x80 | (gain_code*16) + channel_code Voltage Gain Code Multiplier Range 0 1 0–20 V 1 2 0–10 V 2 4 0–5 V 3 5 0–4 V 4 8 0–2.5 V 5 10 0–2 V 6 16 0–1.25 V 7 20 0–1 V Single-Ended Differential 4–20 mA Channel Code Channel Code * Input Lines Lines Input Lines 0 +AIN0 -AIN1 8 AIN0 AIN0 1 +AIN2 -AIN3 9 AIN1 AIN1 2 +AIN4 -AIN5 10 AIN2 AIN2 3 +AIN6 -AIN7 11 AIN3 AIN3 4 Reserved 12 AIN4 Reserved 5 Reserved 13 AIN5 Reserved 6 Reserved 14 AIN6 Reserved 7 Reserved 15 AIN7 Reserved * Negative input is ground. len, the output bit length, is always 12 bits. 58 Fox (LP3500) RETURN VALUE A value corresponding to the voltage on the analog input channel, which will be: 0–2047 for 11-bit A/D conversions (bit 12 for sign) -1 for overflow SEE ALSO anaInConfig, anaIn User’s Manual 59 int anaIn(unsigned int channel, int opmode, int gaincode); Reads the value of an analog input channel using the direct method of addressing the ADS7870 A/D converter. PARAMETERS channel is the analog input channel number (0 to 7) corresponding to AIN0–AIN7 opmode is the mode of operation: SINGLE—single-ended input line DIFF—differential input line mAMP—milliamp input line channel SINGLE DIFF mAMP 0 +AIN0 +AIN0 -AIN1 +AIN0 1 +AIN1 — +AIN1 2 +AIN2 +AIN2 -AIN3 +AIN2 3 +AIN3 — +AIN3 4 +AIN4 +AIN4 -AIN5 — 5 +AIN5 — — 6 +AIN6 +AIN6 -AIN7 — 7 +AIN7 — — gaincode is the gain code of 0 to 7: Voltage Gain Code Range 0 0–20 V 1 0–10 V 2 0–5 V 3 0–4 V 4 0–2.5 V 5 0–2 V 6 0–1.25 V 7 0–1 V RETURN VALUE A value corresponding to the voltage on the analog input channel, which will be: 0–2047 for 11-bit A/D conversions (signed 12th bit) ADOVERFLOW (defined macro = -4096) if overflow or out of range SEE ALSO anaIn, anaInConfig, anaInDriver 60 Fox (LP3500) int anaInCalib(int channel, int opmode, int gaincode, int value1, float volts1, int value2, float volts2); Calibrates the response of the A/D converter channel as a linear function using the two conversion points provided. Four values are calculated and placed into global table _adcCalib to be stored later store into simulated EEPROM using the function anaInEEWr(). Each channel will have the following information: a linear constant, a voltage offset, a calculation gain code used to calculate calibrations, and a user gain code to set voltage range (defaults to the calculation gain code). NOTE: Vcc monitoring is disabled when anaInCalib is running. PARAMETERS channel is the analog input channel number (0 to 7) corresponding to AIN0–AIN7 opmode is the mode of operation: SINGLE—single-ended input line DIFF—differential input line mAMP—milliamp input line channel SINGLE DIFF mAMP 0 +AIN0 +AIN0 -AIN1 +AIN0 1 +AIN1 — +AIN1 2 +AIN2 +AIN2 -AIN3 +AIN2 3 +AIN3 — +AIN3 4 +AIN4 +AIN4 -AIN5 — 5 +AIN5 — — 6 +AIN6 +AIN6 -AIN7 — 7 +AIN7 — — User’s Manual 61 gaincode is the gain code of 0 to 7: Voltage Gain Code Range 0 0–20 V 1 0–10 V 2 0–5 V 3 0–4 V 4 0–2.5 V 5 0–2 V 6 0–1.25 V 7 0–1 V value1 is the first A/D converter channel value (0–2047). volts1 is the voltage or current corresponding to the first A/D converter channel value (0 to +10 V or 4to 20 mA). value2 is the second A/D converter channel value (0–2047). volts2 is the voltage or current corresponding to the first A/D converter channel value (0 to +10 V or 4to 20 mA). RETURN VALUE 0 if successful. -1 if not able to make calibration constants. SEE ALSO anaIn, anaInVolts, anaInmAmps, anaInDiff, anaInSetRange, anaInVoltXGain, anaInCalib, brdInit 62 Fox (LP3500) float anaInVolts(unsigned int channel, unsigned int gaincode); Reads the state of a single-ended analog input channel and uses the previously set calibration constants to convert it to volts. PARAMETER channel is the channel number (0–7): Single-Ended Channel Code * Input Lines 0 +AIN0 1 +AIN1 2 +AIN2 3 +AIN3 4 +AIN4 5 +AIN5 6 +AIN6 7 +AIN7 * Negative input is ground. gaincode is the gain code of 0 to 7. Voltage Gain Code Range 0 0–20 V 1 0–10 V 2 0–5 V 3 0–4 V 4 0–2.5 V 5 0–2 V 6 0–1.25 V 7 0–1 V RETURN VALUE A voltage value corresponding to the voltage on the analog input channel. ADOVERFLOW (defined macro = -4096) if overflow or out of range. SEE ALSO anaInCalib, anaIn, anaInmAmps, brdInit User’s Manual 63 float anaInmAmps(unsigned int channel); Reads the state of an analog input channel and uses the previously set calibration constants to convert it to current. PARAMETER channel is 0–3: 4–20 mA Channel * Input Lines 0 AIN0 1 AIN1 2 AIN2 3 AIN3 * Negative input is ground. RETURN VALUE A current value between 4.00 and 20.00 mA corresponding to the current on the analog input channel. ADOVERFLOW (defined macro = -4096) if overflow or out of range. SEE ALSO anaInCalib, anaIn, anaInVolts 64 Fox (LP3500) float anaInDiff(unsigned int channel, unsigned int gaincode); Reads the state of a differential analog input channel and uses the previously set calibration constants to convert it to volts. PARAMETER channel is the channel number (0, 2, 4, 6): Differential Channel Input Lines 0 +AIN0 -AIN1 2 +AIN2 -AIN3 4 +AIN4 -AIN5 6 +AIN6 -AIN7 gaincode is the gain code of 0 to 7. Voltage Gain Code Range 0 0–20 V 1 0–10 V 2 0–5 V 3 0–4 V 4 0–2.5 V 5 0–2 V 6 0–1.25 V 7 0–1 V RETURN VALUE A voltage value corresponding to the voltage on the analog input channel. ADOVERFLOW (defined macro = -4096) if overflow or out of range. SEE ALSO anaInCalib, anaIn, anaInmAmps, brdInit User’s Manual 65 int anaInEERd(unsigned int channel, int opmode, unsigned int gaincode); Reads the calibration constants, gain, and offset for an input based on its designated channel code posi- tion into global table _adcCalib. The constants are stored in the top 1K of the reserved user block memory area 0x1C00–0x1FFF. NOTE: This function cannot be run in RAM. PARAMETER channel is the analog input channel number (0 to 7) corresponding to AIN0–AIN7. opmode is the mode of operation: SINGLE—single-ended input line DIFF—differential input line mAMP—milliamp input line channel SINGLE DIFF mAMP 0 +AIN0 +AIN0 -AIN1 +AIN0 1 +AIN1 — +AIN1 2 +AIN2 +AIN2 -AIN3 +AIN2 3 +AIN3 — +AIN3 4 +AIN4 +AIN4 -AIN5 — 5 +AIN5 — — 6 +AIN6 +AIN6 -AIN7 — 7 +AIN7 — — ALLCHAN read all channels for selected opmode gaincode is the gain code of 0 to 7. The gaincode parameter is ignored when channel is ALLCHAN. Voltage Gain Code Range 0 0–20 V 1 0–10 V 2 0–5 V 3 0–4 V 4 0–2.5 V 5 0–2 V 6 0–1.25 V 7 0–1 V RETURN VALUE 0 if successful. -1 if address is invalid or out of range. SEE ALSO anaInEEWr, anaInCalib 66 Fox (LP3500) int anaInEEWr(unsigned int channel, int opmode unsigned int gaincode); Writes the calibration constants, gain, and offset for an input based on its designated channel code posi- tion from global table _adcCalib. The constants are stored in the top 1K of the reserved user block memory area 0x1C00–0x1FFF. NOTE: This function cannot be run in RAM. PARAMETER channel is the analog input channel number (0 to 7) corresponding to AIN0–AIN7. opmode is the mode of operation: SINGLE—single-ended input line DIFF—differential input line mAMP—milliamp input line channel SINGLE DIFF mAMP 0 +AIN0 +AIN0 -AIN1 +AIN0 1 +AIN1 — +AIN1 2 +AIN2 +AIN2 -AIN3 +AIN2 3 +AIN3 — +AIN3 4 +AIN4 +AIN4 -AIN5 — 5 +AIN5 — — 6 +AIN6 +AIN6 -AIN7 — 7 +AIN7 — — ALLCHAN read all channels for selected opmode gaincode is the gain code of 0 to 7. The gaincode parameter is ignored when channel is ALLCHAN. Voltage Gain Code Range 0 0–20 V 1 0–10 V 2 0–5 V 3 0–4 V 4 0–2.5 V 5 0–2 V 6 0–1.25 V 7 0–1 V RETURN VALUE 0 if successful. -1 if address is invalid or out of range. SEE ALSO anaInEEWr, anaInCalib User’s Manual 67 4.4.6 Vcc Monitoring (LP3500 only) void VccMonitorInit(int state); PIO3 on the ADS7870 A/D converter enables or disables Vcc monitoring. If monitoring is enabled, ana- log input channel AIN7 is not available. PARAMETER state 1 = enable Vcc monitor 0 = disable Vcc monitor SEE ALSO VccMonitor, anaInConfig, brdInit float VccMonitor(void); If Vcc monitoring is enabled, the Vcc level is read by the ADS7870 A/D converter and is converted to a voltage value. RETURN VALUE A voltage value corresponding to the voltage on the analog input channel. SEE ALSO VccMonitorInit, anaInVolts, brdInit 68 Fox (LP3500) 4.4.7 PWM Outputs The PWM functions in this section can be used to operate the analog outputs on the LP3500 model. int pwmOutConfig(unsigned long frequency); Sets the base frequency for the PWM pulses and enables the PWM driver on all four channels. The base frequency is the frequency without pulse spreading. Pulse spreading (see pwm_set) will increase the frequency by a factor of 4. PARAMETERS frequency is the frequency (in Hz). RETURN VALUE Actual frequency set. This will be the closest possible match to the requested frequency. SEE ALSO pwmOut int pwmOut(unsigned int channel, float dutycycle); Sets a voltage (0 to VDD on an analog output channel according to the percent duty cycle of the 1024- clock-count cycle.) PARAMETERS channel is the output channel to write to (0–3). dutycycle is the percent duty (or on) cycle value of the 1024-clock-count cycle (i.e., 0.25). RETURN VALUE 0 if successful -1 if an invalid channel number is used -2 if an invalid duty cycle was requested SEE ALSO pwmOutConfig User’s Manual 69 4.5 Relay Output (LP3500 only) int relayOut(int relay, int value) A 10 ms low-to-high pulse sets the state of a relay. On power-up or brdInit() the relay contact will go to the normally closed (NC) RESET contact. PARAMETERS relay 0 = the one relay value is a value used to connect the relay common contact: 0 = relay normally closed (NC or RESET) (Parallel Port PG5) 1 = relay normally open (NO or SET) (Parallel Port PG4) RETURN VALUE 0 if successful -1 if the normal power source is not available 70 Fox (LP3500) APPENDIX A. LP3500 SPECIFICATIONS Appendix A provides the specifications for the LP3500, and describes the conformal coating. User’s Manual 71 ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� #� ��� ���� ��� ��� ���� ��� ��� #� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� �&’’()* ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� A.1 Electrical and Mechanical Characteristics Figure A-1 shows the mechanical dimensions for the LP3500. �@����93& B�@��C � ��%�" ��� �� ��� ��� ��� ��� #�� #�� #�� ��� ��� ��� ��������� �������’��(����� �� ��� ��� #� #�� ��� "� #�� ���"�����������������������’�� ��� ��� �""����;� ���"�������’����� ��� ��� ��� ��� ��� �� �� #�� ��� ��� �� ��� � ���������< ��� ��� ��� �� �� �� #�� �� ��� ��� �� ���� !� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� #�� �� ��� �� "� �� ��� ��� ��!�� ��� ��� �� ��� ��� ��� ��� �� � ��� ��� ��� � ������������������� � ������� ���� ���� ������������������������������������������� ��� ����������� ��� �$� �@�� �@�� B�@�C B��C �@�� B��C �@��� B�@��C �@�� B��C �@�� B��C Figure A-1. LP3500 Dimensions 72 Fox (LP3500) ��� � ��!�%�" �� �� ��� �@��� �@�� B��C B�@�C �@�� B��C � ��� ���������������������������������������������������������������� Table A-1 lists the electrical, mechanical, and environmental specifications for the LP3500. Table A-1. LP3500 Specifications Feature LP3500 LP3510 Microprocessor Rabbit 3000® at up to 7.4 MHz EMI Reduction Spectrum spreader for ultra-low EMI (radiated emissions) Flash Memory 512K (2 × 256K) 256K SRAM 512K 128K Socketed 3 V lithium coin Panasonic CR2330, 265 mA·h, Backup Battery supports RTC and SRAM, connection for user-supplied external battery Supports optional LCD/keypad module with Keypad/Display 7 keys and 122 × 32 graphic display Digital Inputs 16: fully protected 0–36 V DC, can handle short spikes ±40 V 10: 8 sink up to 200 mA each, 36 V DC max.; Digital Outputs 2 source up to 200 mA each, 36 V DC max. Relay Output 1 C-form, 1 A, 30 V DC None  Eight single-ended or four differential inputs  1MΩ input impedance  Sampling rate up to 200 samples/s  Eight software-controlled ranges from 0–1 V to 0–20 V DC Single-Ended Inputs  Resolution: 11 bits Analog Inputs None  Accuracy: 8 bits  4 channels can be set individually for 4–20 mA with plug-in jumpers  1 channel has software-selectable voltage-monitoring option Differential Inputs  Resolution: 12 bits  Accuracy: 9 bits 3 unfiltered pulse-width modulated, Analog Outputs None 1 kΩ output impedance User’s Manual 73 Table A-1. LP3500 Specifications (continued) Feature LP3500 LP3510 6 shared high-speed, CMOS-compatible ports:  1 RS-485  3 RS-232 (one 5-wire and one 3-wire or three 3-wire), jumper option for Serial Ports logic-level outputs; one RS-232 port needs to have wake-up capability  1 logic-level serial interface for optional add-ons  1 asynchronous clocked serial port dedicated for programming Serial Rate Max. asynchronous baud rate = CLK/8 Real-Time Clock Yes Ten 8-bit timers (6 cascadable from the first), Timers one 10-bit timer with 2 match registers Watchdog/Supervisor Yes Pulse-Width Modulators 10-bit free-running counter and four pulse-width registers 3 V to 30 V DC Power 20 mA (max.) @ 7.4 MHz, 100 µA max. @ 2 kHz (with linear regulator turned off) Operating Temperature –40°C to +70°C Humidity 5% to 95%, noncondensing  0.1" headers I/O and misc. signals: one 1 × 25, two 1 × 17 headers Display: one 2 × 13 header  2 mm headers Connectors Programming Port: one 2 × 5 header Serial Interface: one 2 × 4 socket  Screw-terminal headers Relay: one 3-position screw-terminal header 2.60" × 3.65" × 0.45" Board Size (66 mm × 93 mm × 11 mm) 74 Fox (LP3500) A.1.1 Exclusion Zone It is recommended that you allow for an “exclusion zone” of 0.25" (6 mm) around the LP3500 in all directions when the LP3500 is incorporated into an assembly that includes other printed circuit boards. This “exclusion zone” that you keep free of other components and boards will allow for sufficient air flow, and will help to minimize any electrical or electromagnetic interference between adjacent boards. An “exclusion zone” of 0.12" (3 mm) is recommended below the LP3500. Figure A-2 shows this “exclusion zone.” �@�� B���C �@�� B��C �@�� B��C $;������� =��� �@�� B��C Figure A-2. LP3500 “Exclusion Zone” When using the LP3500 with the Prototyping Board, do not install any components in the prototyping area on the Prototyping Board between the LP3500 and the Prototyping Board. User’s Manual 75 �@�� B��C �@�� B��C �@�� B�C �@�� B�C A.1.2 Headers The LP3500 uses 0.1" IDC headers at J1–J4 for physical connection to other boards. J5, the programming port, is a 2 × 5 header with a 2 mm pin spacing. Figure A-3 shows the LP3500 footprint. These values are relative to the mounting hole. ,0 ,� ,1 ,4 ,5 ,� ,- ������� ���� �@��� B�@��C �@��� B�@�C �@��� �@��� B�@�C B�@�C �@��� B��@�C �@��� �@��� B��@�C B�@�C �@��� B��@�C Figure A-3. User Board Footprint for LP3500 76 Fox (LP3500) �@��� B�@�C �@��� B�@�C �@��� B��@�C �@��� B��@�C �@��� B��@�C �@��� B��@�C ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� ��� #� ���� ��� ��� ���� ��� ��� ��� #� ���� ��� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� �&’’()* ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� A.2 Conformal Coating The areas around the 32 kHz real-time clock crystal oscillator has had the Dow Corning silicone-based 1-2620 conformal coating applied. The conformally coated area is shown in Figure A-4. The conformal coating protects these high-impedance circuits from the effects of moisture and contaminants over time. ��� ������! ����������� � ��%�" ��� �� ��� ��� ��� #�� ��� #�� #�� ��� ��� ��� �� ��� ��� #� #�� ��� "� #�� ��� ��� ��� ��� ��� ��� ��� �� �� #�� ��� ��� �� ��� � ��� ��� ��� �� �� �� #�� �� ��� ��� �� ���� !� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� #�� �� ��� �� "� �� ��� ��� ��!�� ��� ��� �� ��� ��� ��� ��� �� � ��� ��� � ��� ������������������� � ������� ���� ���� ��� ������������������������������������������� ��� ����������� �$� Figure A-4. LP3500 Areas Receiving Conformal Coating Any components in the conformally coated area may be replaced using standard soldering procedures for surface-mounted components. A new conformal coating should then be applied to offer continuing protection against the effects of moisture and contaminants. NOTE: For more information on conformal coatings, refer to Technical Note 303, Con- formal Coatings. User’s Manual 77 ��� � ��!�%�" �� ��� �� � ��� ���������������������������������������������������������������� A.3 Jumper Configurations Figure A-5 shows the header locations used to configure the various LP3500 options via jumpers. *�"����� � ���� ���� #���������� ���� ���� ���� ���� ���� ���� ��� ���� ���� ���� �� ��� ���� �� ���� ���� ���� �����,� ���� �� ������� ���� ���� �$� Figure A-5. Location of LP3500 Configurable Positions 78 Fox (LP3500) ���� ���� ���� ���� ���� ���� ���� ��� ���� ��� ���� ��� ���� ��� ���� ���� ���� �� ��� �� ��� �� ��� �� ���� �� ���� �� ���� ���� �� ���� ���� �� ��� ���� ���� ���� ���� ���� ���� �� ��������������������������������������������������������������� ��������� ��� ��!�����! Table A-2 lists the configuration options. Table A-2. LP3500 Jumper Configurations Factory Header Description Pins Connected Default None Voltage Option × 1–2 AIN0 4–20 mA Option A/D Converter Voltage/Current J3 3–4 AIN1 4–20 mA Option Measurement Options 5–6 AIN2 4–20 mA Option 7–8 AIN3 4–20 mA Option 1–2 RS-232 Level × JP1 RxE RS-232/Logic Level Select 2–3 Logic Level 1–2 RS-232 Level × JP2 TxE RS-232/Logic Level Select 2–3 Logic Level 1–2 RS-232 Level × JP3 RxC RS-232/Logic Level Select 2–3 Logic Level 1–2 RS-232 Level × JP4 TxC RS-232/Logic Level Select 2–3 Logic Level 1–2 RS-232 Level × JP5 RxB RS-232/Logic Level Select 2–3 Logic Level 1–2 RS-232 Level × JP6 TxB RS-232/Logic Level Select 2–3 Logic Level 1–2 128K LP3510 JP7 SRAM Size 2–3 512K LP3500 1–2 128K/256K × JP8 Flash Memory Size 2–3 512K 1–2 128K/256K LP3500 JP9 Flash Memory Size 2–3 512K 1–2 Normal Mode × JP10 Flash Memory Bank Select 2–3 Bank Mode User’s Manual 79 Table A-2. LP3500 Jumper Configurations (continued) Factory Header Description Pins Connected Default JP11 Manufacturing Use 1–2 × JP12 Manufacturing Use 1–2 × JP13 Manufacturing Use 1–2 × NOTE: The jumper connections on header J3 are made using standard slip-on jumpers. All other jumper connections except those across JP11 and JP12 are made using 0 Ω surface-mounted resistors. 390 Ω current-limiting resistors are used on JP11 and JP12. 80 Fox (LP3500) A.4 Use of Rabbit 3000 Parallel Ports Figure A-6 shows the Rabbit 3000 parallel ports. ������� ������� ������� ������� ������ ������ �����; �������2�������� �����9 ���2����2���� ������ �������2�������� +&##�* <�������������;>��?��= ���2����2���� �?���?� ���� ������ �?�2��?���?� ���2���� �����7 <�������������9�?��= ����,���������% ���2���� ���2���� �����7 0������2 <�������������= �������2�������� ��������� A ���2������2 +��! �� ��� ���� +���� ���/������ ����!�&)1 ���2����2�+��! <�������������= +��!��2 ����%�������� +����2 !����! ;��%���;�����+ !����� ��� ����� ������� !����� Figure A-6. LP3500 Rabbit-Based Subsystems Table A-3 lists the Rabbit 3000 parallel ports and their use in the LP3500. Table A-3. Use of Rabbit 3000 Parallel Ports Port I/O Signal Output Function State PA0 Input IN08 Pulled up PA1 Input IN09 Pulled up PA2 Input IN10 Pulled up PA3 Input IN11 Pulled up PA4 Input IN12 Pulled up PA5 Input IN12 Pulled up PA6 Input IN14 Pulled up PA7 Input IN15 Pulled up Low when external power PB0 Input Power Input Detect source is connected; high for battery Pulled up when not driven PB1 Input CLKA by programming port PB2 Input IN04 Pulled up User’s Manual 81 Table A-3. Use of Rabbit 3000 Parallel Ports (continued) Port I/O Signal Output Function State PB3 Input IN05 Pulled up PB4 Input IN06 Pulled up PB5 Input IN07 Pulled up PB6 Output LCD Buffer Enable Inactive high PB7 Output Serial Device Select Inactive high PC0 Output TXD Serial Device Int. Inactive high Serial Port D PC1 Input RXD Serial Device Int. Inactive high PC2 Output RTS/TxC RS-232 Inactive high Serial Port C PC3 Input CTS/RxC RS-232 Inactive high PC4 Output TxB RS-232 Inactive high Serial Port B PC5 Input RxB RS-232 Inactive high PC6 Output TxA Programming Port Inactive high Serial Port A PC7 Input RxA Programming Port Inactive high PD0 Output OUT0 Inactive low PD1 Output OUT1 Inactive low PD2 Output OUT2 Inactive low PD3 Output OUT3 Inactive low PD4 Output OUT4 Inactive low PD5 Output OUT5 Inactive low PD6 Output OUT6 Inactive low PD7 Output OUT7 Inactive low PE0 Input IN00 Pulled up PE1 Input IN01 Pulled up PE2 Output OUT8 Inactive low PE3 Output OUT9 Inactive low PE4 Input IN02 Pulled up PE5 Input IN03 Pulled up PE6 Output LCD/Keypad Module Reset Line Inactive high PE7 Output LCD/Keypad Module Device Select Inactive high 82 Fox (LP3500) Table A-3. Use of Rabbit 3000 Parallel Ports (continued) Port I/O Signal Output Function State PF0 Output ADC Serial Clock Inactive high PF1 Input ADC Busy Inactive low PF2 Input Not used Pulled up PF3 Output ADC Device Select Inactive high PF4 Output PWM0 Inactive high PF5 Output PWM1 Inactive high PF6 Output PWM2 Inactive high Low when external power PF7 Output Power Enable Control source is connected; high for battery PG0 Output RS-485 Transmit Enable Inactive low PG1 Output RS-232 Shutdown Control Inactive high PG2 Output TxF RS-485 Inactive high Serial Port F PG3 Input RxF RS-485 Inactive high PG4 Output Relay Set Inactive low PG5 Output Relay Reset Inactive low PG6 Output TxE RS-232 Inactive high Serial Port E PG7 Input RxE RS-232 Inactive high User’s Manual 83 84 Fox (LP3500) APPENDIX B. PROTOTYPING BOARD Appendix B describes the features and accessories of the Proto- typing Board included with the LP3500 Tool Kit, and explains the use of the Prototyping Board to demonstrate the LP3500 and to build prototypes of your own circuits. The screw-terminal headers on the Prototyping Board facilitate access to the LP3500 connector pins, and the Prototyping Board is available for purchase separately. User’s Manual 85 ��� ��� ��� ��� ��� ��� � �� �� �� ������������������������������������������������������������������������������������������������������������������������������������������������� B.1 Mechanical Dimensions and Layout Figure B-1 shows the mechanical dimensions and layout for the LP3500 Prototyping Board. ��� ��� ��� ��� ��� ��� ��� �� � �� �� �� �� �� � �������� ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ � �@�� B���C Figure B-1. LP3500 Prototyping Board Dimensions Table B-1 lists the electrical, mechanical, and environmental specifications for the Proto- typing Board. Table B-1. LP3500 Prototyping Board Specifications Parameter Specification Board Size 3.41" × 4.14" × 0.45" (87 mm × 105 mm × 11 mm) Operating Temperature –40°C to +70°C Humidity 5% to 95%, noncondensing Prototyping Area 2.2" × 3.4" (56 mm × 86 mm) throughhole, 0.1" spacing 86 Fox (LP3500) ��� �!���������!��������!�������!� �@�� B��C � �� �� �� !� !� !� !� ����������������������������������������������������������������������������������������������������������������������������������������������� �� �� ,00 ,0� ,0- ,0� �������� B.2 Using the Prototyping Board B.2.1 Interface to LP3500 The Prototyping Board serves as a convenient interface for the LP3500, extending the IDC headers to convenient screw-terminal connectors, and provides interfaces to the AC adapter included with the Tool Kit and to a user-supplied external battery. Figure B-2 shows the pinouts for the Prototyping Board. /������ ��"��� $;������ #�����! ���������� ,� ��� ���� ���� ��� ,�- ,�� ���� ��� ,� ���� ��� &����� ���� ��� ��"��� ���� ���+��! +��-�- ���� ���+��! ���� ��� ��� ��� ���� ��� ,- �23 ���� ��� ���"��� ���� +��01� �!>���� ,0 ��� �!>���� ������$� ��� . ��� ����� �� ��""�! ��� ���� ��� ���� ���� ���� /������ ���� ���"��� ���� ���’������ ���� �����’�� ���� ���� ���� ��� �!���������!��������!�������!� ,� ($/� +���/� ����� ��"�� Figure B-2. LP3500 Prototyping Board Pinout NOTE: The LP3500 must be plugged in to the Prototyping Board as described in Chapter 2, “Getting Started,” for these signals to be available. User’s Manual 87 ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ,-� ,-- ,-� !� !� !� !� ����������������������������������������������������������������������������������������������������������������������������������������������� ������������������������������������������������������������������������������������������������������������������������������������������������� B.2.2 Demonstration Board The Prototyping Board is actually both a demonstration board and a prototyping board. As a demonstration board, it can be used to demonstrate the functionality of the LP3500 right out of the box without any modifications to either board. There are no jumpers or dip switches to configure or misconfigure on the Prototyping Board so that the initial setup is very straightforward. The Prototyping Board comes with the basic components necessary to demonstrate the operation of the LP3500. Four LEDs (DS1–DS4) are connected to PD0–PD3, and four switches (S1–S4) are connected to PE0, PE1, PE4, and PE5 to demonstrate the interface to the Rabbit 3000 microprocessor. NOTE: Before running sample programs based on the LP3500, you will have to plug in the LP3500 to the Prototyping Board as described in Chapter 2, “Getting Started.” B.2.3 Prototyping Area Small to medium circuits can be prototyped using point-to-point wiring with 20 to 30 AWG wire on the prototyping area. Raw DC input, VIN, and GND lines surround the prototyp- ing area. The resistor pack located next to the pushbutton switches may be removed to disconnect the LEDs and pushbutton switches from the Prototyping Board circuits, giving your LP3500 exclusive access to what you may develop in the prototyping area. +K and VIN are tied together by resistor R1 located beside header J44. Cut off R1 if you intend to supply a separate +K. 88 Fox (LP3500) APPENDIX C. LCD/KEYPAD MODULE An optional LCD/keypad is available for the LP3500. Appendix C describes the LCD/keypad module and provides the software calls to make full use of the LCD/keypad module. C.1 Specifications Two optional LCD/keypad modules—with or without a panel-mounted NEMA 4 water- resistant bezel—are available for use with the LP3500. They are shown in Figure C-1. (�/>.�!"���3������ Figure C-1. LCD/Keypad Module Models LCD/keypad modules sold prior to the launch of the LP3500 might not be voltage- compatible with the LP3500. Contact your Rabbit sales representative or your authorized distributor for further assistance in purchasing an LCD/keypad module. Mounting hardware and a 127 mm (5") or 60 cm (24") extension cable are also available for the LCD/keypad module through your Rabbit sales representative or authorized distributor. User’s Manual 89 Table C-1 lists the electrical, mechanical, and environmental specifications for the LCD/ keypad module. Table C-1. LCD/Keypad Specifications Parameter Specification 2.60" × 3.00" × 0.75" Board Size (66 mm × 76 mm × 19 mm) 4.50" × 3.60" × 0.30" Bezel Size (114 mm × 91 mm × 7.6 mm) Operating Range: 0°C to +50°C Temperature Storage Range: –40°C to +85°C Humidity 5% to 95%, noncondensing * Power Consumption 1.5 W maximum with backlight on Connections Connects to header J9 (Display Interface) on LP3500 LCD Panel Size 122 × 32 graphic display Keypad 7-key keypad LEDs Seven user-programmable LEDs * The backlight adds approximately 650 mW to the power consumption. The LCD/keypad module has 0.1" IDC header sockets at J1, J2, and J3 �@��� B�@�C for physical connection to other boards or ribbon cables. Figure C-2 shows the LCD/keypad module foot- ,� print. These values are relative to one of the mounting holes. NOTE: All measurements are in inches followed by millimeters enclosed in parentheses. All dimen- ,- ,� sions have a manufacturing toler- ance of ±0.01" (0.25 mm). �@��� �@��� B�@�C B��@�C �@��� B��@�C �@��� B��@�C Figure C-2. User Board Footprint for LCD/Keypad Module 90 Fox (LP3500) �@��� B��@�C �@��� �@��� B��@�C B��@�C C.2 Contrast Adjustment Starting in 2005, LCD/keypad modules were factory-configured to optimize their contrast based on the voltage of the system they would be used in. Be sure to select a KDU3V LCD/ keypad module for use with the LP3500 — these modules operate at 3.3 V. You may adjust the contrast using the potentiometer at R2 as shown in Figure C-3. KDU5V LCD/keypad modules configured for 5 V may be used with the LP3500, but the backlight will be dim. (�/>.�!"���3������,��"������ ���������� ���� ������+ ����������� #����� ��������� ��’���� ����� ��� � �� ����� ��� ��� ���� �������� �� �� �� �� �� ���������� �� �� �� �� �� �� �� �� �� �� ��� ��� %��� ��� ��� �� #� � � � ��� � � �� ��� � � ��� ��� ��� ��� �� ��� ��� � � � � � #� #� #� #� #� ��=�� �� #� %����� �� �@��� �@��� � 4@1@�D���� ��� ��� �� ��� ��� ��!�%�" ����� � Figure C-3. LCD/Keypad Module Contrast Adjustment You can set the contrast on the LCD display of pre-2005 LCD/keypad modules by adjust- ing the potentiometer at R2 or by setting the voltage for 2.8 V by connecting the jumper across pins 1–2 on header J5 as shown in Figure C-3. Only one of these two options is available on these older LCD/keypad modules. NOTE: Older LCD/keypad modules that do not have a header at J5 or a contrast adjust- ment potentiometer at R2 are limited to operate only at 5 V, and will not work with the LP3500. The older LCD/keypad modules are no longer being sold. User’s Manual 91 �� ��� ��� �� �� ��� ��� #� ��� �� ��� ��� ��� ��� ��� ��� ��� �� �� �&)’��-@����>���� C.3 Keypad Labeling The keypad may be labeled according to your needs. A template is provided in Figure C-4 to allow you to design your own keypad label insert. �@�� B��C �@�� B��C Figure C-4. Keypad Template To replace the keypad legend, remove the old legend and insert your new legend prepared according to the template in Figure C-4. The keypad legend is located under the blue key- pad matte, and is accessible from the left only as shown in Figure C-5. �(*6&9�0&5(0�3/�0-1&’(9 ������’:(�507(�;(*6&9�,&’’(@ Figure C-5. Removing and Inserting Keypad Label The sample program KEYBASIC.C in the 122x32_1x7 folder in SAMPLES\LCD_KEYPAD shows how to reconfigure the keypad for different applications. 92 Fox (LP3500) C.4 Header Pinouts Figure C-6 shows the pinouts for the LCD/keypad module. �� � �� Figure C-6. LCD/Keypad Module Pinouts NOTE: Note that there are no connections from headers J2 and J3 of the LCD/keypad module to the LP3500. These headers interface to the keypad and to the LEDs on the LCD/keypad module, and need to be interfaced to the digital I/O on the LP3500 if you need keypad or LED functionality. The LEDs may be driven by an active signal either in software or in hardware. C.4.1 I/O Address Assignments The LCD and keypad on the LCD/keypad module are addressed by the /CS strobe as explained in Table C-2. Table C-2. LCD/Keypad Module Address Assignment Address Function 0xE000 Device select base address (/CS) 0xExx0–0xExx7 LCD control 0xExx8 LED enable 0xExx9 Not used 0xExxA 7-key keypad 0xExxB (bits 0–6) 7-LED driver 0xExxB (bit 7) LCD backlight on/off 0xExxC–ExxF Not used User’s Manual 93 ��� ��� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� %��� ��� %��� %��� ��� ��� %��� %��� %��� %��� %��� %��� %��� +�! +��! %��� %��� ����%� ��� %��� %��� +�! +��! ����%� ��� C.5 Bezel-Mount Installation This section describes and illustrates how to bezel-mount the LCD/keypad module. Follow these steps for bezel-mount installation. 1. Cut mounting holes in the mounting panel in accordance with the recommended dimen- sions in Figure C-7, then use the bezel faceplate to mount the LCD/keypad module onto the panel. �@�����2��� B�C �%*�%* �@��� B�@�C �@��� B��@�C �@��� B��@�C Figure C-7. Recommended Cutout Dimensions 2. Carefully “drop in” the LCD/keypad module with the bezel and gasket attached. 94 Fox (LP3500) �@��� B�@�C �@��� B��@�C ��� ��� ��� ��� ��� ��� �� ��� ��� ��� �� 3. Fasten the unit with the four 4-40 screws and washers included with the LCD/keypad module. If your panel is thick, use a 4-40 screw that is approximately 3/16" (5 mm) longer than the thickness of the panel. #�?��>���8�� ��!�%�"������ �� �� �� �� �� �� �� #� �� � �� �� �� �� �� �� �� �� ����� �� #� #� #� #� #� #� #� ��� � � �� ��� �� Figure C-8. LCD/Keypad Module Mounted in Panel (rear view) Carefully tighten the screws until the gasket is compressed and the plastic bezel face- plate is touching the panel. Do not tighten each screw fully before moving on to the next screw. Apply only one or two turns to each screw in sequence until all are tightened manually as far as they can be so that the gasket is compressed and the plastic bezel faceplate is touching the panel. User’s Manual 95 �� ��� � ��!�%�" �� ��� �� ��!�%�"������ �� �� �� �� �� �� �� #� �� � � ��� �� ��� �� �� �� �� �� �� �� �� #� #� #� #� #� #� #� ��� � � �� ��� �� C.6 Connect the LCD/Keypad Module to Your LP3500 The LCD/keypad module can be located as far as 2 ft. (60 cm) away from the LP3500, and is connected via a ribbon cable as shown in Figure C-9. �34�� �� � ��� ���������������������������������������������������������������� �34�� Figure C-9. Connecting LCD/Keypad Module to LP3500 Note the locations and connections relative to pin 1 on both the LP3500 and the LCD/key- pad module. Rabbit offers two different lengths of ribbon cable–5" (127 mm) and 2 ft. (60 cm). Contact your authorized distributor or a Rabbit sales representative for more information. 96 Fox (LP3500) ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� ��� #� ���� ��� ��� ���� ��� ��� ��� #� ���� ��� ��� ��� ���� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� �&’’()* ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� � ��%�" ��� ��� �� ��� ��� ��� ��� #�� #�� #�� ��� ��� ��� �� ��� ��� #� #�� ��� "� ��� ��� #�� ��� ��� ��� ��� ��� �� ��� ��� ��� �� ��� #�� ��� ��� �� ��� � ��� �� ��� ��� ��� �� �� �� ��� #�� �� ��� ��� �� ���� !� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� #�� ��� �� ��� �� "� �� ��� ��� ��!�� ��� ��� ��� �� ��� ��� ��� ��� � �� ��� � ��� ��� �� ������������������� � ������� ���� ���� ������������������������������������������� ��� ����������� ��� �$� C.7 LCD/Keypad Module Function Calls The LCD/keypad module is normally off. Add the devPowerSet function call after brdInit to turn on the LCD/keypad buffers. brdInit(); // Initialize the LP3500 devPowerSet(DISPDEV, 1); // Enable LCD/keypad buffer C.7.1 LEDs When power is applied to the LCD/keypad module for the first time, the red LED (DS1) will come on, indicating that power is being applied to the LCD/keypad module. The red LED is turned off when the brdInit function executes. One function is available to control the LEDs, and can be found in the LIB\Rabbit3000\ DISPLAYS\LCD122KEY7.LIB library. void dispLedOut(int led, int value); LED on/off control. This function will only work when the LCD/keypad module is connected to the LP3500. PARAMETERS led is the LED to control. 0 = LED DS1 1 = LED DS2 2 = LED DS3 3 = LED DS4 4 = LED DS5 5 = LED DS6 6 = LED DS7 value is the value used to control whether the LED is on or off (0 or 1). 0 = off 1 = on RETURN VALUE None. SEE ALSO brdInit User’s Manual 97 C.7.2 LCD Display The functions used to control the LCD display are contained in the LIB\Rabbit3000\ DISPLAYS\GRAPHIC.LIB library. When x and y coordinates on the display screen are specified, x can range from 0 to 121, and y can range from 0 to 31. These numbers repre- sent pixels from the top left corner of the display. void glInit(void); Initializes the display devices, clears the screen. RETURN VALUE None. SEE ALSO glDispOnOFF, glBacklight, glSetContrast, glPlotDot, glBlock, glPlotDot, glPlotPolygon, glPlotCircle, glHScroll, glVScroll, glXFontInit, glPrintf, glPutChar, glSetBrushType, glBuffLock, glBuffUnlock, glPlotLine void glBackLight(int onOff); Turns the display backlight on or off. PARAMETER onOff turns the backlight on or off 1—turn the backlight on 0—turn the backlight off RETURN VALUE None. SEE ALSO glInit, glDispOnoff, glSetContrast void glDispOnOff(int onOff); Sets the LCD screen on or off. Data will not be cleared from the screen. PARAMETER onOff turns the LCD screen on or off 1—turn the LCD screen on 0—turn the LCD screen off RETURN VALUE None. SEE ALSO glInit, glSetContrast, glBackLight 98 Fox (LP3500) void glSetContrast(unsigned level); Sets display contrast. NOTE: This function is not used with the LCD/keypad module since the support circuits are not available on the LCD/keypad module. void glFillScreen(char pattern); Fills the LCD display screen with a pattern. PARAMETER The screen will be set to all black if pattern is 0xFF, all white if pattern is 0x00, and vertical stripes for any other pattern. RETURN VALUE None. SEE ALSO glBlock, glBlankScreen, glPlotPolygon, glPlotCircle void glBlankScreen(void); Blanks the LCD display screen (sets LCD display screen to white). RETURN VALUE None. SEE ALSO glFillScreen, glBlock, glPlotPolygon, glPlotCircle void glBlock(int x, int y, int bmWidth, int bmHeight); Draws a rectangular block in the page buffer and on the LCD if the buffer is unlocked. Any portion of the block that is outside the LCD display area will be clipped. PARAMETERS x is the x coordinate of the top left corner of the block. y is the y coordinate of the top left corner of the block. bmWidth is the width of the block. bmWidth is the height of the block. RETURN VALUE None. SEE ALSO glFillScreen, glBlankScreen, glPlotPolygon, glPlotCircle User’s Manual 99 void glPlotVPolygon(int n, int *pFirstCoord); Plots the outline of a polygon in the LCD page buffer, and on the LCD if the buffer is unlocked. Any portion of the polygon that is outside the LCD display area will be clipped. If fewer than 3 vertices are specified, the function will return without doing anything. PARAMETERS n is the number of vertices. *pFirstCoord is a pointer to array of vertex coordinates: x1,y1, x2,y2, x3,y3,... RETURN VALUE None. SEE ALSO glPlotPolygon, glFillPolygon, glFillVPolygon void glPlotPolygon(int n, int y1, int x2, int y2, ...); Plots the outline of a polygon in the LCD page buffer and on the LCD if the buffer is unlocked. Any portion of the polygon that is outside the LCD display area will be clipped. If fewer than 3 vertices are specified, the function will return without doing anything. PARAMETERS n is the number of vertices. y1 is the y coordinate of the first vertex. x1 is the x coordinate of the first vertex. y2 is the y coordinate of the second vertex. x2 is the x coordinate of the second vertex. ... are the coordinates of additional vertices. RETURN VALUE None. SEE ALSO glPlotVPolygon, glFillPolygon, glFillVPolygon 100 Fox (LP3500) void glFillVPolygon(int n, int *pFirstCoord); Fills a polygon in the LCD page buffer and on the LCD screen if the buffer is unlocked. Any portion of the polygon that is outside the LCD display area will be clipped. If fewer than 3 vertices are specified, the function will return without doing anything. PARAMETERS n is the number of vertices. *pFirstCoord is a pointer to array of vertex coordinates: x1,y1, x2,y2, x3,y3,... RETURN VALUE None. SEE ALSO glFillPolygon, glPlotPolygon, glPlotVPolygon void glFillPolygon(int n, int x1, int y1, int x2, int y2, ...); Fills a polygon in the LCD page buffer and on the LCD if the buffer is unlocked. Any portion of the polygon that is outside the LCD display area will be clipped. If fewer than 3 vertices are specified, the function will return without doing anything. PARAMETERS n is the number of vertices. x1 is the x coordinate of the first vertex. y1 is the y coordinate of the first vertex. x2 is the x coordinate of the second vertex. y2 is the y coordinate of the second vertex. ... are the coordinates of additional vertices. RETURN VALUE None. SEE ALSO glFillVPolygon, glPlotPolygon, glPlotVPolygon void glPlotCircle(int xc, int yc, int rad); Draws the outline of a circle in the LCD page buffer and on the LCD if the buffer is unlocked. Any por- tion of the circle that is outside the LCD display area will be clipped. PARAMETERS xc is the x coordinate of the center of the circle. yc is the y coordinate of the center of the circle. rad is the radius of the center of the circle (in pixels). RETURN VALUE None. SEE ALSO User’s Manual 101 glFillCircle, glPlotPolygon, glFillPolygon 102 Fox (LP3500) void glFillCircle(int xc, int yc, int rad); Draws a filled circle in the LCD page buffer and on the LCD if the buffer is unlocked. Any portion of the circle that is outside the LCD display area will be clipped. PARAMETERS xc is the x coordinate of the center of the circle. yc is the y coordinate of the center of the circle. rad is the radius of the center of the circle (in pixels). RETURN VALUE None. SEE ALSO glPlotCircle, glPlotPolygon, glFillPolygon void glXFontInit(fontInfo *pInfo, char pixWidth, char pixHeight, unsigned startChar, unsigned endChar, unsigned long xmemBuffer); Initializes the font descriptor structure, where the font is stored in xmem. PARAMETERS *pInfo is a pointer to the font descriptor to be initialized. pixWidth is the width (in pixels) of each font item. pixHeight is the height (in pixels) of each font item. startChar is the value of the first printable character in the font character set. endChar is the value of the last printable character in the font character set. xmemBuffer is the xmem pointer to a linear array of font bitmaps. RETURN VALUE None. SEE ALSO glPrinf User’s Manual 103 unsigned long glFontCharAddr(fontInfo *pInfo, char letter); Returns the xmem address of the character from the specified font set. PARAMETERS *pInfo is the xmem address of the bitmap font set. letter is an ASCII character. RETURN VALUE xmem address of bitmap character font, column major, and byte-aligned. SEE ALSO glPutFont, glPrintf void glPutFont(int x, int y, fontInfo *pInfo, char code); Puts an entry from the font table to the page buffer and on the LCD if the buffer is unlocked. Each font character's bitmap is column major and byte-aligned. Any portion of the bitmap character that is outside the LCD display area will be clipped. PARAMETERS x is the x coordinate (column) of the top left corner of the text. y is the y coordinate (row) of the top left corner of the text. *pInfo is a pointer to the font descriptor. code is the ASCII character to display. RETURN VALUE None. SEE ALSO glFontCharAddr, glPrintf void glSetPfStep(int stepX, int stepY); Sets the glPrintf() printing step direction. The x and y step directions are independent signed values. The actual step increments depend on the height and width of the font being displayed, which are multi- plied by the step values. PARAMETERS stepX is the glPrintf x step value stepY is the glPrintf y step value RETURN VALUE None. SEE ALSO Use glGetPfStep() to examine the current x and y printing step direction. 104 Fox (LP3500) int glGetPfStep(void); Gets the current glPrintf() printing step direction. Each step direction is independent of the other, and is treated as an 8-bit signed value. The actual step increments depends on the height and width of the font being displayed, which are multiplied by the step values. RETURN VALUE The x step is returned in the MSB, and the y step is returned in the LSB of the integer result. SEE ALSO Use glGetPfStep() to control the x and y printing step direction. void glPutChar(char ch, char *ptr, int *cnt, glPutCharInst *pInst) Provides an interface between the STDIO string-handling functions and the graphic library. The STDIO string-formatting function will call this function, one character at a time, until the entire format- ted string has been parsed. Any portion of the bitmap character that is outside the LCD display area will be clipped. PARAMETERS ch is the character to be displayed on the LCD. *ptr is not used, but is a place holder for STDIO string functions. *cnt is not used, is a place holder for STDIO string functions. *pInst is a font descriptor pointer. RETURN VALUE None. SEE ALSO glPrintf, glPutFont, doprnt User’s Manual 105 void glPrintf(int x, int y, fontInfo *pInfo, char *fmt, ...); Prints a formatted string (much like printf) on the LCD screen. Only the character codes that exist in the font set are printed, all others are skipped. For example, '\b', '\t', '\n' and '\r' (ASCII backspace, tab, new line, and carriage return, respectively) will be printed if they exist in the font set, but will not have any effect as control characters. Any portion of the bitmap character that is outside the LCD display area will be clipped. PARAMETERS x is the x coordinate (column) of the top left corner of the text. y is the y coordinate (row) of the top left corner of the text. *pInfo is a font descriptor pointer. *fmt is a formatted string. ... are formatted string conversion parameter(s). EXAMPLE glprintf(0,0, &fi12x16, "Test %d\n", count); RETURN VALUE None. SEE ALSO glXFontInit void glBuffLock(void); Increments LCD screen locking counter. Graphic calls are recorded in the LCD memory buffer and are not transferred to the LCD if the counter is non-zero. NOTE: glBuffLock() and glBuffUnlock() can be nested up to a level of 255, but be sure to balance the calls. It is not a requirement to use these procedures, but a set of glBuffLock() and glBuffUnlock() bracketing a set of related graphic calls speeds up the rendering significantly. RETURN VALUE None. SEE ALSO glBuffUnlock, glSwap void glBuffUnlock(void); Decrements the LCD screen locking counter. The contents of the LCD buffer are transferred to the LCD if the counter goes to zero. RETURN VALUE None. SEE ALSO glBuffLock, glSwap 106 Fox (LP3500) void glSwap(void); Checks the LCD screen locking counter. The contents of the LCD buffer are transferred to the LCD if the counter is zero. RETURN VALUE None. SEE ALSO glBuffUnlock, glBuffLock, _glSwapData (located in the library specifically for the LCD that you are using) void glSetBrushType(int type); Sets the drawing method (or color) of pixels drawn by subsequent graphic calls. PARAMETER type value can be one of the following macros. PIXBLACK draws black pixels (turns pixel on). PIXWHITE draws white pixels (turns pixel off). PIXXOR draws old pixel XOR'ed with the new pixel. RETURN VALUE None. SEE ALSO glGetBrushType int glGetBrushType(void); Gets the current method (or color) of pixels drawn by subsequent graphic calls. RETURN VALUE The current brush type. SEE ALSO glSetBrushType void glPlotDot(int x, int y); Draws a single pixel in the LCD buffer, and on the LCD if the buffer is unlocked. If the coordinates are outside the LCD display area, the dot will not be plotted. PARAMETERS x is the x coordinate of the dot. y is the y coordinate of the dot. RETURN VALUE None. SEE ALSO glPlotline, glPlotPolygon, glPlotCircle User’s Manual 107 void glPlotLine(int x0, int y0, int x1, int y1); Draws a line in the LCD buffer, and on the LCD if the buffer is unlocked. Any portion of the line that is beyond the LCD display area will be clipped. PARAMETERS x0 is the x coordinate of one endpoint of the line. y0 is the y coordinate of one endpoint of the line. x1 is the x coordinate of the other endpoint of the line. y1 is the y coordinate of the other endpoint of the line. RETURN VALUE None. SEE ALSO glPlotDot, glPlotPolygon, glPlotCircle void glLeft1(int left, int top, int cols, int rows); Scrolls byte-aligned window left one pixel, right column is filled by current pixel type (color). PARAMETERS left is the top left corner of bitmap, must be evenly divisible by 8, otherwise truncates. top is the top left corner of the bitmap. cols is the number of columns in the window, must be evenly divisible by 8, otherwise truncates. rows is the number of rows in the window. RETURN VALUE None. SEE ALSO glHScroll, glRight1 void glRight1(int left, int top, int cols, int rows); Scrolls byte-aligned window right one pixel, left column is filled by current pixel type (color). PARAMETERS left is the top left corner of bitmap, must be evenly divisible by 8, otherwise truncates. top is the top left corner of the bitmap. cols is the number of columns in the window, must be evenly divisible by 8, otherwise truncates. rows is the number of rows in the window. RETURN VALUE None. SEE ALSO glHScroll, glLeft1 108 Fox (LP3500) void glUp1(int left, int top, int cols, int rows); Scrolls byte-aligned window up one pixel, bottom column is filled by current pixel type (color). PARAMETERS left is the top left corner of bitmap, must be evenly divisible by 8, otherwise truncates. top is the top left corner of the bitmap. cols is the number of columns in the window, must be evenly divisible by 8, otherwise truncates. rows is the number of rows in the window. RETURN VALUE None. SEE ALSO glVScroll, glDown1 void glDown1(int left, int top, int cols, int rows); Scrolls byte-aligned window down one pixel, top column is filled by current pixel type (color). PARAMETERS left is the top left corner of bitmap, must be evenly divisible by 8, otherwise truncates. top is the top left corner of the bitmap. cols is the number of columns in the window, must be evenly divisible by 8, otherwise truncates. rows is the number of rows in the window. RETURN VALUE None. SEE ALSO glVScroll, glUp1 User’s Manual 109 void glHScroll(int left, int top, int cols, int rows, int nPix); Scrolls right or left, within the defined window by x number of pixels. The opposite edge of the scrolled window will be filled in with white pixels. The window must be byte-aligned. Parameters will be verified for the following: 1. The left and cols parameters will be verified that they are evenly divisible by 8. If not, they will be truncated to a value that is a multiple of 8. 2. Parameters will be checked to verify that the scrolling area is valid. The minimum scrolling area is a width of 8 pixels and a height of one row. PARAMETERS left is the top left corner of bitmap, must be evenly divisible by 8. top is the top left corner of the bitmap. cols is the number of columns in the window, must be evenly divisible by 8. rows is the number of rows in the window. nPix is the number of pixels to scroll within the defined window (a negative value will produce a scroll to the left). RETURN VALUE None. SEE ALSO glVScroll 110 Fox (LP3500) void glVScroll(int left, int top, int cols, int rows, int nPix); Scrolls up or down, within the defined window by x number of pixels. The opposite edge of the scrolled window will be filled in with white pixels. The window must be byte-aligned. Parameters will be verified for the following: 1. The left and cols parameters will be verified that they are evenly divisible by 8. If not, they will be truncated to a value that is a multiple of 8. 2. Parameters will be checked to verify that the scrolling area is valid. The minimum scrolling area is a width of 8 pixels and a height of one row. PARAMETERS left is the top left corner of bitmap, must be evenly divisible by 8. top is the top left corner of the bitmap. cols is the number of columns in the window, must be evenly divisible by 8. rows is the number of rows in the window. nPix is the number of pixels to scroll within the defined window (a negative value will produce a scroll up). RETURN VALUE None. SEE ALSO glHScroll void glXPutBitmap(int left, int top, int width, int height, unsigned long bitmap); Draws bitmap in the specified space. The data for the bitmap are stored in xmem. This function calls glXPutFastmap automatically if the bitmap is byte-aligned (the left edge and the width are each evenly divisible by 8). Any portion of a bitmap image or character that is outside the LCD display area will be clipped. PARAMETERS left is the top left corner of the bitmap. top is the top left corner of the bitmap. width is the width of the bitmap. height is the height of the bitmap. bitmap is the address of the bitmap in xmem. RETURN VALUE None. SEE ALSO glXPutFastmap, glPrintf User’s Manual 111 void glXPutFastmap(int left, int top, int width, int height, unsigned long bitmap); Draws bitmap in the specified space. The data for the bitmap are stored in xmem. This function is like glXPutBitmap, except that it is faster. The restriction is that the bitmap must be byte-aligned. Any portion of a bitmap image or character that is outside the LCD display area will be clipped. PARAMETERS left is the top left corner of the bitmap, must be evenly divisible by 8, otherwise truncates. top is the top left corner of the bitmap. width is the width of the bitmap, must be evenly divisible by 8, otherwise truncates. height is the height of the bitmap. bitmap is the address of the bitmap in xmem. RETURN VALUE None. SEE ALSO glXPutBitmap, glPrintf int TextWindowFrame(windowFrame *window, fontInfo *pFont, int x, int y, int winWidth, int winHeight) Defines a text-only display window. This function provides a way to display characters within the text window using only character row and column coordinates. The text window feature provides end-of-line wrapping and clipping after the character in the last column and row is displayed. NOTE: Execute the TextWindowFrame function before other Text... functions. PARAMETERS *window is a window frame descriptor pointer. *pFont is a font descriptor pointer. x is the x coordinate of the top left corner of the text window frame. y is the y coordinate of the top left corner of the text window frame. winWidth is the width of the text window frame. winHeight is the height of the text window frame. RETURN VALUE 0—window frame was successfully created. -1—x coordinate + width has exceeded the display boundary. -2—y coordinate + height has exceeded the display boundary. 112 Fox (LP3500) void TextGotoXY(windowFrame *window, int col, int row); Sets the cursor location to display the next character. The display location is based on the height and width of the character to be displayed. NOTE: Execute the TextWindowFrame function before using this function. PARAMETERS *window is a pointer to a font descriptor. col is a character column location. row is a character row location. RETURN VALUE None. SEE ALSO TextPutChar, TextPrintf, TextWindowFrame void TextCursorLocation(windowFrame *window, int *col, int *row); Gets the current cursor location that was set by a Graphic Text... function. NOTE: Execute the TextWindowFrame function before using this function. PARAMETERS *window is a pointer to a font descriptor. *col is a pointer to cursor column variable. *row is a pointer to cursor row variable. RETURN VALUE Lower word = Cursor Row location Upper word = Cursor Column location SEE ALSO TextGotoXY, TextPrintf, TextWindowFrame, TextCursorLocation User’s Manual 113 void TextPutChar(struct windowFrame *window, char ch); Displays a character on the display where the cursor is currently pointing. If any portion of a bitmap character is outside the LCD display area, the character will not be displayed. The cursor increments its position as needed. NOTE: Execute the TextWindowFrame function before using this function. PARAMETERS *window is a pointer to a font descriptor. ch is a character to be displayed on the LCD. RETURN VALUE None. SEE ALSO TextGotoXY, TextPrintf, TextWindowFrame, TextCursorLocation void TextPrintf(struct windowFrame *window, char *fmt, ...); Prints a formatted string (much like printf) on the LCD screen. Only printable characters in the font set are printed, also escape sequences, '\r' and '\n' are recognized. All other escape sequences will be skipped over; for example, '\b' and 't' will print if they exist in the font set, but will not have any effect as control characters. The text window feature provides end-of-line wrapping and clipping after the character in the last col- umn and row is displayed. The cursor then remains at the end of the string. NOTE: Execute the TextWindowFrame function before using this function. PARAMETERS *window is a pointer to a font descriptor. *fmt is a formatted string. ... are formatted string conversion parameter(s). EXAMPLE TextPrintf(&TextWindow, "Test %d\n", count); RETURN VALUE None. SEE ALSO TextGotoXY, TextPutChar, TextWindowFrame, TextCursorLocation 114 Fox (LP3500) C.7.3 Keypad The functions used to control the keypad are contained in the Dynamic C LIB\ Rabbit3000\DISPLAYS\KEYPADS\KEYPAD7.LIB library. void keyInit(void); Initializes keypad process RETURN VALUE None. SEE ALSO brdInit void keyConfig(char cRaw, char cPress, char cRelease, char cCntHold, char cSpdLo, char cCntLo, char cSpdHi); Assigns each key with key press and release codes, and hold and repeat ticks for auto repeat and debouncing. PARAMETERS cRaw is a raw key code index. 1x7 keypad matrix with raw key code index assignments (in brackets): [0] [1] [2] [3] [4] [5] [6] User Keypad Interface cPress is a key press code An 8-bit value is returned when a key is pressed. 0 = Unused. See keypadDef() for default press codes. cRelease is a key release code. An 8-bit value is returned when a key is pressed. 0 = Unused. cCntHold is a hold tick, which is approximately one debounce period or 5 µs. How long to hold before repeating. 0 = No Repeat. cSpdLo is a low-speed repeat tick, which is approximately one debounce period or 5 µs. How many times to repeat. 0 = None. cCntLo is a low-speed hold tick, which is approximately one debounce period or 5 µs. How long to hold before going to high-speed repeat. 0 = Slow Only. User’s Manual 115 cSpdHi is a high-speed repeat tick, which is approximately one debounce period or 5 µs. How many times to repeat after low speed repeat. 0 = None. RETURN VALUE None. SEE ALSO keyProcess, keyGet, keypadDef void keyProcess(void); Scans and processes keypad data for key assignment, debouncing, press and release, and repeat. NOTE: This function is also able to process an 8 x 8 matrix keypad. RETURN VALUE None SEE ALSO keyConfig, keyGet, keypadDef char keyGet(void); Get next keypress. RETURN VALUE The next keypress, or 0 if none SEE ALSO keyConfig, keyProcess, keypadDef int keyUnget(char cKey); Pushes the value of cKey to the top of the input queue, which is 16 bytes deep. PARAMETER cKey RETURN VALUE None. SEE ALSO keyGet 116 Fox (LP3500) void keypadDef(); Configures the physical layout of the keypad with the default ASCII return key codes. Keypad physical mapping 1 x 7 0 4 1 5 2 6 3 ['L'] ['U'] ['D'] ['R'] ['–'] ['+'] ['E'] where 'D' represents Down Scroll 'U' represents Up Scroll 'R' represents Right Scroll 'L' represents Left Scroll '–' represents Page Down '+' represents Page Up 'E' represents the ENTER key Example: Do the followingfor the above physical vs. ASCII return key codes. keyConfig ( 3,'R',0, 0, 0, 0, 0 ); keyConfig ( 6,'E',0, 0, 0, 0, 0 ); keyConfig ( 2,'D',0, 0, 0, 0, 0 ); keyConfig ( 4,'-',0, 0, 0, 0, 0 ); keyConfig ( 1,'U',0, 0, 0, 0, 0 ); keyConfig ( 5,'+',0, 0, 0, 0, 0 ); keyConfig ( 0,'L',0, 0, 0, 0, 0 ); Characters are returned upon keypress with no repeat. RETURN VALUE None. SEE ALSO keyConfig, keyGet, keyProcess void keyScan(char *pcKeys); Writes "1" to each row and reads the value. The position of a keypress is indicated by a zero value in a bit position. PARAMETER *pcKeys is a pointer to the address of the value read. RETURN VALUE None. SEE ALSO keyConfig, keyGet, keypadDef, keyProcess User’s Manual 117 C.8 Sample Programs Sample programs illustrating the use of the LCD/keypad module with the LP3500 board are provided in the SAMPLES\LP3500\Display_Keypad directory. To run a sample program, open it with the File menu (if it is not still open), compile it using the Compile menu, and then run it by selecting Run in the Run menu. The LP3500 must be connected to a PC using the programming cable as described in Section 2.1, “LP3500 Connections.” Each sample program contains detailed instructions for running it. 118 Fox (LP3500) APPENDIX D. PLASTIC ENCLOSURE The plastic enclosure provides a secure way to protect your LP3500. The enclosure itself may be mounted on any flat sur- face. The complete plastic enclosure consists of a base and a cover. The base alone is a convenient surface on which to mount the LP3500, and also provides a means to mount the LP3500 on any flat surface. Appendix D describes how to mount the LP3500 inside the plas- tic enclosure, and provides details on mounting the assembly. The plastic enclosure is able to accommodate the following LP3500 combinations.  LP3500 board only  LP3500 Prototyping Board only  LP3500 mounted on LP3500 Prototyping Board User’s Manual 119 ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� ��� #� ���� ��� ��� ���� ��� ��� #� ��� ���� ��� ��� ��� ���� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� �&’’()* ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� ��� #� ���� ��� ��� ���� ��� ��� #� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� �&’’()* ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� D.1 Assembly Instructions 1. Remove any stand-offs on the LP3500 board or LP3500 board/Prototyping Board com- bination to be enclosed. � ��%�" ��� �� ��� ��� ��� ��� #�� #�� #�� ��� ��� ��� �� ��� ��� #� #�� "� ��� #�� ��� ��� � ��� ��� �� ��� ��� ��� �� #�� ��� ��� �� ��� � ��� ��� ��� �� �� �� #�� �� �� ��� ��� ���� ��� ��� !� ��� ��� ��� ��� ��� ��� ��� ��� #�� �� ��� �� "� �� ��� ��� ��!�� ��� ��� �� ��� ��� ��� ��� �� � ��� ��� ��� � ������������������� � ������� ���� ���� ������������������������������������������� ��� ����������� ��� �$� � � Figure D-1. Remove Stand-Offs from LP3500 Board 2. Attach the LP3500, the LP3500 Prototyping Board, or the board combination to the plastic enclosure base. Position the board(s) over the plastic enclosure base as shown below in Figure D-2. Attach the board(s) to the base using the two 4-40 × ¼ screws supplied with the enclosure base. NOTE: You will need longer 4-40 screws if you are mounting the combination with the LP3500 installed on the Prototyping Board. � ��%�" ��� �� ��� ��� ��� ��� #�� #�� #�� ��� ��� ��� �� ��� ��� #� #�� "� ��� #�� ��� � ��� ��� ��� �� ��� ��� ��� �� #�� ��� ��� �� ��� � ��� ��� ��� �� �� �� #�� �� �� ��� ��� ���� !� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� #�� �� ��� �� "� �� ��� ��� ��!�� ��� �� ��� ��� ��� ��� ��� �� � ��� ��� ��� � ������������������� � ������� ���� ������������������������������������������� ������������������ ��� �$� Figure D-2. Attach Board(s) to Plastic Enclosure Base 120 Fox (LP3500) ��� � ��!�%�" �� ��� �� ��� � ��!�%�" �� ��� �� � ��� ���������������������������������������������������������������� � ��� ���������������������������������������������������������������� ��� ��� ��� ��� ��� ��� ���� ���� ��� ���� ���� ��� ���� ��� ���� ��� ��� ��� ��� ���� ���� ��� #� ���� ��� ��� ���� ��� ��� #� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ���� ��� ��� ��� ������ ���� �&’’()* ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� � ������������������������������������������������������������������������������������� 3. Mount plastic enclosure (optional). Use four #10 screws to attach the plastic enclosure at the four outer corner mounting holes to the surface on which it will be mounted. This step will be most suitable to production versions of LP3500 units once development has been completed. 4. Attach the enclosure cover to the base. Position the cover over the plastic enclosure base as shown below in Figure D-3. Attach the cover to the base using the two 4-40 × 7/8 screws supplied. NOTE: You will need longer 4-40 screws if you are mounting the combination with the LP3500 installed on the Prototyping Board. �-’1:(9 /39( � ��%�" ��� �� ��� ��� ��� ��� ��� #�� #�� #�� ��� ��� �� ��� ��� #� #�� ��� "� #�� ��� � ��� ��� ��� ��� ��� ��� �� �� #�� ��� ��� �� ��� � ��� ��� �� ��� �� �� #�� �� �� ��� ���� ��� !� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� #�� �� ��� �� �� "� ��� ��� ��!�� ��� ��� �� ��� ��� ��� ��� �� � ��� ��� ��� � ������������������� � ������� ���� ���� ������������������������������������������� ����$� ����������� ��� Figure D-3. Attach Enclosure Top User’s Manual 121 ��� � ��!�%�" �� ��� �� � ��� ���������������������������������������������������������������� D.2 Dimensions Figure D-4 shows the dimensions for the plastic enclosure. �@�� B��C �@���E�B�@��,,C 3/�17’�-FF�(&1:�1-)4() �@�� B���C �@�� B���C �@�� �@�� �@��� B�@�C B��C B��C �@�� B���C Figure D-4. Plastic Enclosure Dimensions 122 Fox (LP3500) �@�� B��C �@�� B���C �@��� �@�� B��C B��C �@��� B���C APPENDIX E. POWER MANAGEMENT Appendix E describes the power circuitry provided on the LP3500. The LP3500 can operate from an unregulated external power source, or from an external battery. There is onboard bat- tery backup for the SRAM and the real-time clock. E.1 External Power Supply Power is normally supplied to the LP3500 via pins 16 and 17 of header J2 on the LP3500. The Prototyping Board provides a convenient header plug for use with the AC adapter included with the LP3500 Tool Kit. The Prototyping Board includes a Shottky diode for protection against reverse polarity. The raw DC power, VIN, goes through a linear regulator as shown in Figure E-1. The lin- ear regulator outputs a Vcc of 2.8 V DC. %������������!���%" �11 ������� � ��� � ��� � �� �� ��� � � ��� ��� ��� ����;� ���G? ���G? ��@��;� #�� �?� ��� ��� ��� ����4? ���;� ����;� ��� #�� ��� ����;� Figure E-1. LP3500 Linear Regulator Circuit The power necessarily dissipated by the regulator can be calculated if both the external input voltage and the current drawn by the LP3500 are known. The current provided by the high-power output drivers does not have to be included if a separate power supply is connected to K so that power does not come from Vcc. User’s Manual 123 The linear regulator maintains its output voltage to within ±5% as long as the linear regula- tor is dissipating less than 0.75 W. Thermal shutdown turns the regulator off when it over- heats. Figure E-1 shows the power operating curves for the specified VIN range of 3–30 V DC. Note that while a VIN range of 3–30 V is possible, 3–15 V is recommended to allow reasonable current. 200 180 160 140 120 100 80 60 40 20 0 0 5 10 15 20 25 30 VIN (V) Figure E-2. Linear Regulator Power Operating Curve The LP3500 can operate at various different power levels, depending on which sections of the board are turned off using the devPowerSet function. Table E-1 lists the sections. Table E-1. LP3500 Sections That Can Be Turned Off Controlled by LP3500 Section Power Consumption Rabbit 3000 Port RS-232 8 mA with load PG1 RS-485 0.1 mA with no load PG0 A/D Converter 0.45 mA at 1.5 ksample/s sampling rate PB6 (LP3500 model only) Relay 120 mA for 10 ms per switch PG4, PG5 (LP3500 model only) 5 mA without backlight, 50 mA for back- LCD/Keypad Module PB0 light, 5 mA for each LED (max. 7 LEDs) NOTE: RxE always remains active to allow the LP3500 to “listen” while it is in the power-save mode. 124 Fox (LP3500) I (mA) Parallel Port PF7 on the Rabbit 3000 chip controls whether the linear regulator is on or off. Parallel Port PB0 senses whether there is an output from the linear regulator, and shuts off the RS-232 (except RxE, which is used to “listen”), RS-485, A/D converter, and relay sec- tions via Parallel Ports PB6, PG0, PG1, PG4, and PG5 to conserve power. E.2 Batteries and External Battery Connections The SRAM and the real-time clock have battery backup. Power to the SRAM and the real- time clock (VRAM) is provided by two different sources, depending on whether the main part of the LP3500 is powered or not. When the LP3500 is powered normally, and Vcc is within operating limits, the SRAM and the real-time clock are powered from Vcc. If power to the board is lost or falls below 2.75 V, the VRAM and real-time clock power will come from either the onboard or the external battery. The reset generator circuit controls the source of power by way of its /RESET output signal. A replaceable onboard 265 mA·h lithium battery provides power to the real-time clock and SRAM when all external power is removed from the circuit board and the LP3500 processor is off. The drain on the battery is typically 46 µA under these worst-case condi- tions, and so the expected life of the onboard battery is 265 mA·h - - - --- -- -- --- -- --- -- -- - - = 240 days. 46 µA The drain on the battery is typically less than 4 µA when external power is applied, and so the expected LP3500 battery in-service life is 265 mA·h ------------------------ = 7.5 years. 4 µA The primary role of the onboard battery is to keep the SRAM and the real-time clock func- tional when the LP3500 processor is off. Even though there is limited capacity in the onboard battery, and its circuit is in parallel with that of the external battery, Rabbit strongly recommends against relying on the onboard battery for any role besides that of keeping the SRAM and the real-time clock functional when the LP3500 processor is off. The short in-service life of the onboard battery highlights the importance of an external battery, especially if the LP3500 is to operate in the power-save mode. A 2.8–3.3 V external battery or equivalent “regulated” voltage is recommended. There is provision for an external battery connection via pins 14 and 15 on header J2 on the LP3500, and the LP3500 Prototyping Board has a plug-in header at J6 that can be used to connect an external battery to the LP3500/Prototyping Board combination. Cycle the main power off/on on the LP3500 after you install a backup battery for the first time, and whenever you replace the battery. This step will minimize the current drawn by the real-time clock oscillator circuit from the backup battery should the LP3500 experi- ence a loss of main power. User’s Manual 125 E.2.1 Replacing the Backup Battery The battery is user-replaceable, and is fitted in a battery holder. To replace the battery, lift up on the spring clip and slide out the old battery. Use only a Panasonic CR2330 or equiv- alent replacement battery, and insert it into the battery holder with the + side facing up. NOTE: The SRAM contents and the real-time clock settings will be lost if the battery is replaced with no power applied to the LP3500. Exercise care if you replace the battery while external power is applied to the LP3500. NOTE: Should it be more convenient, it is also possible to install the onboard battery on the other side of the LP3500 board. CAUTION: There is an explosion danger if the battery is short-circuited, recharged, or replaced incorrectly. Replace the battery only with the same type or an equivalent type recommended by the battery manufacturer. Dispose of used batteries according to the battery manufacturer’s instructions. E.2.2 Power to VRAM Switch The VRAM switch on the LP3500 module, shown in Figure E-3, allows the battery backup to provide power when the external power goes off. The switch provides an isola- tion between Vcc and the battery when Vcc goes low. This prevents the Vcc line from draining the battery. �11 +�! ��� ����;� #�� ���� ��� ���4? ��!��� Figure E-3. VRAM Switch Field-effect transistor Q12 provides a very small voltage drop between Vcc and VRAM (<100 mV, typically 10 mV) so that the board components powered by Vcc will not have a significantly different voltage than VRAM. When the LP3500 is not in reset, the /RESOUT line will be high. This allows VRAM to nearly equal Vcc. When the LP3500 is in reset, the /RESOUT line will go low. This provides an isolation between Vcc and VRAM. 126 Fox (LP3500) E.2.3 Reset Generator The LP3500 module uses a reset generator on the module, U11, to reset the Rabbit 3000 microprocessor when the voltage drops below the voltage necessary for reliable operation. The reset occurs between 2.55 V and 2.75 V, typically 2.63 V. E.3 Chip Select Circuit The current drain on the battery in a battery-backed circuit must be kept at a minimum. When the LP3500 is not powered, the battery keeps the SRAM memory contents and the real-time clock (RTC) going. The SRAM has a powerdown mode that greatly reduces power consumption. This powerdown mode is activated by raising the chip select (CS) signal line. Normally the SRAM requires Vcc to operate. However, only 2 V is required for data retention in powerdown mode. Thus, when power is removed from the circuit, the battery voltage needs to be provided to both the SRAM power pin and to the CS signal line. The CS control circuit accomplishes this task for the SRAM’s chip select signal line. In a powered-up condition, the CS control circuit must allow the processor’s chip select signal /CS1 to control the SRAM’s CS signal /CSRAM. So, with power applied, /CSRAM must be the same signal as /CS1, and with power removed, /CSRAM must be held high (but only needs to be battery voltage high).The isolated /CSRAM line has a 220 kΩ pullup resistor to VRAM (R46). This pullup resistor keeps /CSRAM at the VRAM voltage level (which under no power condition is the backup battery’s regulated voltage at a little more than 2 V). User’s Manual 127 128 Fox (LP3500) ��� ��� ��� ��� ��� ��� ��� #� ��� ��� ��� ��� ��� �� ��� ��� �� �� ��� �� ��� �� ��� �� �� ��� �� ��� �� �� �� ��� ��� � �� �� �� ������������������������������������������������������������������������������������������������������������������������������������������������������������������ APPENDIX F. RUNNING A SAMPLE PROGRAM Appendix G goes through the steps of running a sample program with the LP3500 connected to the Prototyping Board. Sample programs are provided in the Dynamic C Samples folder. The various directories in the Samples folder contain specific sample programs that illustrate the use of the cor- responding Dynamic C libraries. The LP3500 folder provides sample programs specific to the LP3500. Each sample pro- gram has comments that describe the purpose and function of the program. Follow the instructions at the beginning of the sample program. Let’s look at the sample program DIGIN.C in the Samples/LP3500/IO folder. 1. Connect the LP3500 to a PC using the programming cable as described in Section 2.1, “LP3500 Connections,” and connect the AC adapter to header J5 on the Prototyping Board. =(&9()� ��3/�5(’<((4 ’:(�%������&49�’:( �- �)-’-’*6348��-&)9 � �������6-)’ ������� ���� ����������� �-0-)(9�(98( ����� ���� ��9�0 ��� ��� ��� ��� ��� ��� ��� �� � �� �� �� �� �� � �������� ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ � � �������������� ������������� )#&*��������� � Figure F-1. Programming Cable and Power Supply Connections User’s Manual 129 �7�9�7�� ��� �!���������!��������!�������!� ��� ��� ��� ��� ��� #� ��� #� #�� ���� ��� �� ��� ��� �� #�� #� �� ���� ��� ��� �� ��� ���� ��� ����� ���� ��� ��� ��� ��� #�� ��� ��� ��� ��� �� �� �� ��� ��� �� ��� ��� ��� !� �� �� ��� ��� #�� �� ��� �� #�� �� ��� ��!�� ��� ��� �� �� �� � �� ��� �� ��� ��� +��!�� ��� ��� ��� ������� ���� !� !� !� !� ����������������������������������������������������������������������������������������������������������������������������������������������� ���� ���� 2. +K must be connected to an external power supply. A 0 Ω resistor on the Prototyping Board (R1) ties +K to VIN from the AC adapter and thus satisfies this requirement as long as the LP3500 is connected to the Prototyping Board. 3. Open DIGIN.C with the File menu, compile it using the Compile menu, and then run it by selecting Run in the Run menu. 4. The following display will appear in the Dynamic C STDIO window. 5. When pressing pushbutton switches S1–S4 on the Prototyping Board you can change the inputs for IN0–IN3 from a “1” to a “0.” 6. Similarly you can view a change to the inputs for IN0–IN15 from a “1” to a “0” when you touch a wire connected to ground to IN0–IN15. 130 Fox (LP3500) INDEX digital inputs ......................... 22 JP1 (RxE RS-232/logic level A switching threshold ........... 22 select) ............................ 79 A/D converter ....................... 31 digital outputs ....................... 23 JP10 (flash memory bank buffered inputs .................. 31 dimensions select) ...................... 37, 79 calibration constants ......... 32 LCD/keypad template ....... 92 JP2 (TxE RS-232/logic level differential measurements . 32 LP3500 .............................. 72 select) ............................ 79 function calls plastic enclosure .............. 122 JP3 (RxC RS-232/logic level anaIn .............................. 60 Prototyping Board ............. 86 select) ............................ 79 anaInCalib .....................61 Dynamic C ........................ 5, 40 JP4 (TxC RS-232/logic level anaInConfig ................... 56 debugging features ............ 40 select) ............................ 79 anaInDriver ...................58 installation ......................... 14 JP5 (RxB RS-232/logic level anaInEERd ....................66 Rabbit Embedded Security select) ............................ 79 anaInEEWr .................... 67 Pack ..........................5, 41 JP6 (TxB RS-232/logic level anaInmAmps .................64 standard features select) ............................ 79 anaInVolts .....................63 debugging ...................... 40 JP7 (SRAM size) .............. 79 single-ended measure- starting ..............................14 JP8 (flash memory size) .... 79 ments ............................. 32 telephone-based technical JP9 (flash memory size) .... 79 voltage ranges ................... 31 support ......................5, 41 jumper locations ................... 78 analog inputs See A/D converter upgrades and patches ........ 41 K USB/serial port converter . 14 B keypad template .................... 92 E battery backup removing and inserting label real-time clock ................ 125 exclusion zone ...................... 75 ....................................... 92 battery connections ............. 125 battery tab ......................... 13 F L board initialization features .................................... 2 LCD/keypad module ............... 3 function calls ..................... 51 flash memory bezel-mount installation .... 94 brdInit ............................ 51 lifetime write cycles .......... 39 contrast adjustment ........... 91 C dimensions ........................90 I function calls CE compliance ........................ 6 ledOut ............................ 97 design guidelines ................. 7 I/O address assignments LEDs .............................97 chip select circuit ................ 127 LCD/keypad module ......... 93 header pinout .................... 93 conformal coating ................. 77 installation I/O address assignments ... 93 plastic enclosure D keypad LP3500 ........................120 function calls digital I/O keyConfig ................ 115 J function calls keyGet .....................116 digBankIn ...................... 53 jumper configurations ..... 78, 79 keyInit .....................115 digBankOut ...................52 J3 (A/D converter voltage/ keypadDef ...............117 digIn ..............................53 current measurement keyProcess ............... 116 digOut ...........................52 options) .........................79 keyScan ...................117 SMODE0 ..........................28 keyUnget .................116 SMODE1 ..........................28 User’s Manual 131 LCD/keypad module (continued) power supply ...................4, 123 M keypad template .................92 battery backup .................125 memory .................................37 LCD display chip select circuit .............127 flash memory configura- function calls connections ........................12 tions ...............................37 glBackLight ...............98 linear voltage regulator ...123 SRAM configuration for glBlankScreen ............99 VRAM switch .................126 different sizes ................37 glBlock .......................99 programming models .....................................2 glBuffLock ...............106 flash vs. RAM ...................39 LP3500 ................................2 glBuffUnlock ...........106 programming port ..............28 LP3510 ................................2 glDispOnOff ..............98 programming cable glDown1 ..................109 connections ........................11 O glFillCircle ...............103 PROG connector ...............35 glFillPolygon ...........101 switching between Program options .....................................3 glFillScreen ................99 Mode and Run Mode ....35 LCD/keypad module ...........3 glFillVPolygon ........101 programming port .................28 plastic enclosure ..................3 glFontCharAddr .......104 Prototyping Board serial flash expansion cards .3 glGetBrushType .......107 dimensions .........................86 P glGetPfStep ..............105 specifications .....................86 glHScroll ..................110 pinout R glInit ...........................98 LCD/keypad module .........93 glLeft1 .....................108 Rabbit 3000 LP3500 headers .................18 glPlotCircle ..............101 parallel ports ......................81 plastic enclosure ..............3, 119 glPlotDot ..................107 real-time clock assembly instructions ......120 glPlotLine ................108 battery backup .................125 dimensions .......................122 glPlotPolygon ..........100 how to set ..........................13 mounting instructions ......121 glPlotVPolygon .......100 relay output ...........................34 setup glPrintf .....................106 reset .......................................12 attach LP3500 to enclosure glPutChar .................105 hardware ............................12 base ...........................120 glPutFont .................104 reset generator .................127 attaching top ................121 glRight1 ...................108 RS-232 ..................................26 power management .............123 glSetBrushType .......107 RS-485 ..................................26 power modes .............19, 20, 21 glSetContrast .............99 baud rate entering power-save mode 20 glSetPfStep ..............104 setting ............................55 function calls .....................47 glSwap .....................107 maximum baud rate ...........26 devPowerSet ..................47 glUp1 .......................109 RS-485 network ....................27 digInAlert ......................50 glVScroll ..................111 powerMode ....................48 glXFontInit ..............103 S rdPowerState .................50 glXPutBitmap ..........111 serCommAlert ...............49 sample programs ...................42 glXPutFastmap ........112 setPowerSource .............50 A/D converter TextCursorLocation .113 timedAlert ......................49 AD_CAL_ALL.C ..........44 TextGotoXY ............113 low-power mode ................19 AD_CAL_CHAN.C ......44 TextPrintf .................114 LP3500 subsystems that can AD_CALDIFF_CH.C ...44 TextPutChar .............114 be turned off ..................20 AD_CALMA_CH.C ......45 TextWindowFrame ..112 normal mode ......................19 AD_RDDIFF_CH.C ......43 model options ....................89 power-save mode ..19, 20, 21 AD_RDMA_CH.C ........43 removing and inserting keypad processor halted .................19 AD_RDVOLT_ALL.C ..43 label ...............................92 resuming normal-power or AD_RDVOLT_CH.C ....43 sample programs .............118 low-power operation .....21 AD_SAMPLE.C ............43 digital I/O DIGBANKIN.C .............42 DIGBANKOUT.C .........42 DIGIN.C ........................42 DIGOUT.C ....................42 132 Fox (LP3500) sample programs (continued) specifications LCD/keypad module . 45, 118 LCD/keypad module KEYBASIC.C ...............92 dimensions ....................90 PONG.C ............................15 electrical ........................ 90 power modes header footprint ............. 90 POWER.C .....................42 mechanical ....................90 PWM outputs relative pin 1 locations .. 90 PWMOUT.C .................44 temperature ...................90 real-time clock LP3500 .............................. 71 RTC_TEST.C ................ 13 dimensions ....................72 SETRTCKB.C ..............13 electrical, mechanical, and relay output environmental ............. 73 SWRELAY.C ................ 44 exclusion zone ............... 75 running a sample program 129 header footprint ............. 76 serial communication headers ..........................76 SIMPLE3WIRE.C ........43 relative pin 1 locations .. 76 SIMPLE485MASTER.C 43 plastic enclosure SIMPLE485SLAVE.C .. 43 dimensions ..................122 Vcc monitoring Prototyping Board ............. 86 VCCMONITOR.C ........44 subsystems ............................17 serial communication ............ 25 T flow control ....................... 54 function calls Tool Kit ................................... 4 ser485Rx .......................55 AC adapter .......................... 4 ser485Tx ........................ 55 DC power supply ................ 4 serCflowcontrolOff .......54 Dynamic C software ........... 4 serCflowcontrolOn ........ 54 plastic enclosure .................. 4 serMode ......................... 54 programming cable ............. 4 programming port ............. 28 Prototyping Board ............... 4 RS-232 description ........... 26 software ............................... 4 RS-485 description ........... 26 stand-offs ................4, 9, 120 RS-485 network ................ 27 User’s Manual ..................... 4 serial flash expansion cards 3, 28 serial interface port (J6) ........ 28 U setup ........................................9 USB/serial port converter ..... 11 attach LP3500 to Prototyping Dynamic C settings ........... 14 Board ............................10 power supply connections . 12 programming cable connec- tions ..............................11 software ................................... 5 libraries .............................46 LCD122KEY7.LIB .......97 LP3500 ..........................46 LP35xx.LIB ..................46 PACKET.LIB ................ 54 RS232.LIB ....................54 User’s Manual 133 134 Fox (LP3500) SCHEMATICS 090-0150 LP3500 Schematic www.rabbit.com/documentation/schemat/090-0150.pdf 090-0151 LP3500 Prototyping Board Schematic www.rabbit.com/documentation/schemat/090-0151.pdf 090-0156 LCD/Keypad Module Schematic www.rabbit.com/documentation/schemat/090-0156.pdf 090-0128 Programming Cable Schematic www.rabbit.com/documentation/schemat/090-0128.pdf You may use the URL information provided above to access the latest schematics directly. User’s Manual 137