DN-6955:A • H-215 FSD-751PL(A), FSD-751RPL(A) Intelligent Low-Flow Photoelectric Duct Smoke Detectors with FlashScan® Intelligent Addressable Devices General NOTIFIER FSD-751PL(A) and FSD-751RPL(A) Intelligent Pho- toelectric Smoke Duct Detectors provide low-flow technology that enables duct smoke detection throughout a broad range of airflow environments in HVAC applications. The low-flow tech- nology can detect smoke at air speed velocities of 100 feet per minute (0.5 m/sec) or greater, while continuing the same reliable performance to 4,000 feet per minute (20.32 m/sec). The intelli- gent low-flow duct detectors sample air currents passing 52398ph1.jpg through a duct and gives dependable performance for shutdown of fans, blowers, and air conditioning systems, preventing the spread of toxic smoke an fire gases through the protected area. FSD-751PL FSD-751PL(A) and FSD-751RPL(A) are compatible with all NOTIFIER addressable panels. FSD-751PL(A) and FSD- 751RPL(A) provide a remote alarm output for use with auxiliary devices, such as the RA400Z(A) remote LED annunciator, as well as remote test capability with the RTS451(A) or RTS451KEY(A) Remote Test Stations. Traditional panels support addresses of 0 – 99. The Flash- Scan® protocol supports addresses of 0 – 159. The patented FlashScan communication protocol was developed by NOTI- FIER Engineering, it greatly enhances the speed of communica- 52398ph2.jpg tion between analog intelligent devices and the Notifier control panel. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new information, the FSD-751RPL panel stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of 3242ra4z.jpg 3242rts4.jpg 3242key.jpg earlier designs. Applications Duct smoke detectors have specific limitations, they are: • NOT a substitute for open area smoke detectors. • NOT a substitute for early warning detection. • NOT a replacement for a building’s regular fire detection sys- tem. Please call NOTIFIER for a copy of System Sensor’s application guide, Proper Use of Smoke Detectors in Duct Applications, (A05-1004-00). RA400Z RTS451 RTS451KEY duct smoke detector terminals accommodate wire sizes up to 12 Features AWG (3.31 mm²). Flexible conduit is recommended for the last • Air velocity rating from 100 to 4,000 feet per minute (0.5 to foot (30.48 cm) of conduit; solid conduit connections may be 20.32 m/sec). used if desired. • Patented telescopic sampling tube. Smoke detectors and alarm system control panels have specifi- • Easily accessible code wheels for addressing detector. cations for Signaling Line Circuit (SLC) wiring. Consult the con- trol panel specifications for wiring requirements before wiring • Outside mounting tabs. the detector loop. The FSD-751PL(A) and FSD-751RPL(A) • Mounts to round or rectangular ducts from 1’ to 12’ (0.3 to 3.7 detectors are designed for ease of wiring; their housing provides meters) wide. a terminal strip with clamping plates. • Transparent cover for convenient visual inspection. LED Features: If programmed with the system control panel, two LEDs on each duct smoke detector light to provide local vis- Installation ible indication. Refer to installation manuals for control panel and duct detector Programming specifications/requirements for intelligent for detailed information or to install equipment. Installation man- system control panels: The number of devices that can have uals for detectors: I561978-003R for FSD-751PL(A), 156-1979- their LEDs programmed to illuminate is limited by the features of 004R for FSD-751RPL(A). the panel and the individual devices. The actual number of devices is determined by the control panel and its ability to sup- Wiring: For signal wiring (the wiring between detectors or from ply LED current. Refer to the control panel installation manual detectors to auxiliary devices), it is recommended that single for details. conductor wire be no smaller than 18 AWG (0.821 mm²). The DN-6955:A • 12/29/06 — Page 1 of 4 Wiring Diagrams for FSD-751PL(A) On to other Detectors on the Loop. 6821wir1.wmf FSD-751PL(A) Duct Smoke Detector using a UL or ULC Listed control panel. FSD-751PL(A) Duct Smoke Detector with an optional Detector RA400Z Terminals RA400Z(A). 6821wir2.wmf FSD-751PL(A) Duct Smoke Detector with RTS451(A)/ 6821wir3.wmf RTS451KEY(A). Detector COMMON TEST NOTE: For RTS451(A), Terminal 3 is not Terminals used. RTS451(A) does not have a Terminal 45 6 6. For RTS451KEY(A), Terminals 3 and 6 Field-Installed are not used. JUMPER 12 3 LED RESET RTS451/RTS451KEY Inlet Tube Selection Outside Duct Width Inlet Tube* Up to 2 feet (0.6096 m) ST-1.5(A) 2 to 4 feet (0.6096 to 1.2192 m) ST-3(A) 4 to 8 feet (1.2192 to 2.4384 m) ST-5(A) 8 to 12 feet (2.4384 to 3.6576 m) ST-10(A) *Inlet tube is required and must be purchased separately. Order One inlet tube for each duct smoke detector ordered. Page 2 of 4 — DN-6955:A • 12/29/06 TEST RA400Z RA400Z RTS451KEY COMMON COMMON COM (+) COM (–) Wiring Diagrams for FSD-751RPL(A) FSD-751RPL(A) Duct Smoke Detector using a UL-Listed control panel: NOTE: 1) Jumper J1 shunt must be installed for 2-W applications. J1 shunt must be removed for power PCB supervision. Note that removal of shunt without adding external power will prevent communications to the panel over the SLC. 2) External power of 24 V AC/DC or 120/220 VAC must be connected in order to power all remote horn or strobe accessories. FSD-751RPL(A) Duct Smoke Detector FSD-751RPL(A) Duct with an optional RA400Z(A): Smoke Detector with RTS451(A)/RTS451KEY(A): FSD-751RPL(A) Duct Smoke Detector with an optional PA400: 7006wir4.wmf DN-6955:A • 12/29/06 — Page 3 of 4 7006wir1.wmf 7006wir2.wmf 7006wir3.wmf Standby current: 300 µA @ 24 VDC (one communication Product Line Information every 5 seconds with LED blink enabled). NOTE: “A” model suffix is for Canadian models. Operating temperature range: 32° to 131°F (0° to 55°C). FSD-751PL: Addressable low-flow duct detector housing with Operating humidity range: 10% to 93% relative humidity (non- photoelectric smoke detector. condensing). FSD-751PLA: Same as above with ULC listing. Storage temperature range: –22°F to +158°F (–30°C to +70°C). FSD-751RPL: Addressable low-flow duct detector housing with Duct air velocity: 100 to 4,000 feet/min (0.5 to 20.32 m/s). photoelectric smoke detector with DPDT relay. Shipping weight: 3.90 lbs. (1.8 kg). FSD-751RPLA: Same as above with ULC listing. Dimensions: 14.75" (37 cm) length x 5.50" (14 cm) width x A5053FS: Replacement photoelectric sensor board. 2.75" (7 cm) deep. A5067: Replacement power board (without relay). FSD-751RPL(A) CONTACT RATINGS A5060: Replacement power board (with relay). Alarm auxiliary contacts (DPDT): 10 A @ 30 VDC; 10 A @ ST-1.5(A): Metal sampling tube, duct widths 1' to 2' (see Inlet 277 VAC (0.75 power factor); 240 VA @ 249 VAC (0.4 power Tube Selection table on page 2 for metric lengths). factor); 1/8 HP @ 120 VAC; 1/4 HP @ 240 VAC. ST-3(A): Metal sampling tube, duct widths 2' to 4'. Minimum switching current for auxiliary contact must be ST-5(A): Metal sampling tube, duct widths 4' to 8'. 100 mA DC minimum @ 5 VDC. ST-10(A): Metal sampling tube, duct widths 8' to 12'. Supervisory contact (SPST): 2.0 A @ 30 VDC (resistive). RA400Z(A): Remote annunciator alarm LED. FSD-751RPL(A) accessory current loads @ 24 VDC: PA400: RTS451(A): Remote test station. Mounts in single-gang box. refer to PA400 data sheet DN-2405. RA400Z(A): 0 mA standby, Includes red alarm LED and magnet test switch. 12 mA maximum in alarm. RTS451(A) and RTS451KEY(A): 0 RTS451KEY(A): Key-activated remote test station. mA standby, 10 mA maximum in alarm. F36-09-11: Replacement filters. M02-04-00: Test magnet. FSD-751RPL(A) CURRENT REQUIREMENTS (USING M02-09-00: Test magnet with telescoping handle. NO ACCESSORIES) S08-39-01: Replacement photo insect screen. 20 – 30 VDC power supply voltage: 26 mA maximum standby P48-61-00: Replacement end cap for plastic sampling tube. current; 87 mA maximum alarm current; 3 to 10 second alarm P48-21-00: Replacement end cap for metal sampling tube. response time; 2 second power-up time. T80-71-00: Replacement plastic sampling tube. 24 VAC, 50/60 Hz power supply voltage: 65 mA RMS maxi- mum standby current; 182 mA RMS maximum alarm current; 3 Specifications to 10 second alarm response time; 2 second power-up time. 120 VAC, 50/60 Hz power supply voltage: 44 mA RMS maxi- FOR FSD-751PL(A) mum standby current; 52 mA RMS maximum alarm current; 3 to 10 second alarm response time; 2 second power-up time. Operating voltage range: 15 to 30 VDC. Standby current: 300 µA @ 24 VDC (one communication 220/240 VAC, 50/60 Hz power supply voltage: 25 mA RMS every 5 seconds with LED blink enabled). maximum standby current; 30 mA RMS maximum alarm current; 3 to 10 second alarm response time; 2 second power-up time. Operating temperature range: 32° to 131°F (0° to 55°C). Operating humidity range: 10% to 93% relative humidity (non- condensing). Agency Listings and Approvals Storage temperature range: –22°F to +158°F (–30°C to +70°C). The listings and approvals below apply to FSD-751PL(A) and Duct air velocity: 100 to 4,000 feet/min (0.5 to 20.32 m/s). FSD-751RPL(A) Intelligent Low-Flow Photoelectric Smoke Duct Shipping weight: 3.35 lbs. (1.5 kg). Detectors. In some cases, certain modules may not be listed by Dimensions: 14.75" (37 cm) length x 5.50" (14 cm) width x certain approval agencies, or listing may be in process. Consult 2.75" (7 cm) deep. factory for latest listing status. FSD-751PL(A) accessory current loads @ 24 VDC: • UL Listed: file S1115 (FSD-751PL, FSD-751RPL). RA400Z(A): 0 mA standby, 10 mA maximum in alarm. • ULC Listed: file S115 (FSD-751PLA, FSD-751RPLA). RTS451(A) and RTS451KEY(A): 0 mA standby, 7.5 mA maxi- • CSFM approved: file 3240-0028:205. mum in alarm. • FM approved. FOR FSD-751RPL(A) • MEA approved: file 384-02-E. • Maryland State Fire Marshal approved: Permit #2127. Operating voltage range: 20 to 30 VDC, 24 VAC/VDC, 120/ 240 VAC auxiliary power (requires a separate auxiliary source). FlashScan®, NOTIFIER® and System Sensor® are registered trademarks of Honeywell International Inc. ©2006 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 4 of 4 — DN-6955:A • 12/29/06