DN-6935:D • H-202 FSP-851(A) Series Intelligent Plug-In Photoelectric Smoke Detectors with FlashScan® Intelligent/Addressable Devices General Notifier FSP-851(A) Series intelligent plug-in smoke detectors with integral communication provide features that surpass con- ventional detectors. Detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detec- tor’s address to be set with rotary, decimal address switches, providing exact detector location for selective maintenance when chamber contamination reaches an unacceptable level. The FSP-851(A) photoelectric detector’s unique optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources. Dual electronic thermistors add 135°F (57°C) fixed-temperature thermal sensing on the FSP- 851T(A). The FSP-851R(A) is a remote test capable detector for use with DNR(A)/DNRW duct detector housings. FSP-851(A) FSP-851(A) in B210LP(A) Base series detectors are compatible with Notifier Onyx and CLIP series Fire Alarm Control Panels (FACPs). FlashScan® (U.S. Patent 5,539,389) is a communication proto- – B200SR(A): 6.875" (17.46 cm) diameter. col developed by Notifier that greatly increases the speed of – B224RB(A): 6.2" (15.748 cm) diameter. communication between analog intelligent devices. Intelligent – B224BI(A): 6.2" (15.748 cm) diameter. devices communicate in a grouped fashion. If one of the devices in the group has new information, the panel’s CPU stops the Shipping Weight: 5.2oz. (147g). group poll and concentrates on single points. The net effect is Operating Temperature range: FSP-851(A), 0°C to 49°C response speed greater than five times that of earlier designs. (32°F to 120°F). FSP-851T(A), 0°C to 38°C (32°F to 100°F). Low temperature signal for FSP-851T(A) at 45°F +/- 10°F (7.22°C +/- 5.54°C). FSP-851R(A) installed in a DNR(A)/DNRW, Features -20°C to 70°C (-4°F to 158°F). • Sleek, low-profile design. UL/ULC Listed Velocity Range: 0-4000 ft/min. (1219.2 m/ • Addressable-analog communication. min.), suitable for installation in ducts. • Stable communication technique with noise immunity. Relative Humidity: 10%-93% noncondensing. • Low standby current. Thermal Ratings: Fixed-temperature setpoint 135°F (57°C). • Two-wire SLC connection. • Compatible with FlashScan® and CLIP protocol systems. DETECTOR SPACING AND APPLICATIONS • Rotary, decimal addressing (1-99 on CLIP systems, 1-159 on Notifier recommends spacing detectors in compliance with FlashScan systems). NFPA 72. In low airflow applications with smooth ceiling, space • Optional remote, single-gang LED accessory. detectors 30 feet (9.144m) for ceiling heights 10 feet (3.148m) and higher. For specific information regarding detector spacing, • Dual LED design provides 360° viewing angle. placement, and special applications refer to NFPA 72. System • Visible bi-color LEDs blink green every time the detector is Smoke Detector Application Guide, document A05-1003, is addressed, and illuminate steady red on alarm (FlashScan available at systemsensor.com systems only). • Remote test feature from the panel. ELECTRICAL SPECIFICATIONS • Walk test with address display (an address on 121 will blink Voltage Range: 15-32 volts DC peak. the detector LED: 12-[pause]-1(FlashScan systems only). Standby Current (max. avg.): 300μA @ 24VDC (one commu- • Built-in functional test switch activated by external magnet. nication every five seconds with LED enabled). • Built-in tamper-resistant feature. LED Current (max.): 6.5mA @ 24 VDC (“ON”). • Sealed against back pressure. • Constructed of off-white fire-resistant plastic, designed to Installation commercial standards, and offers an attractive appearance. FSP-851(A) plug-in detectors use a separate base to simplify • 94-5V plastic flammability rating. installation, service, and maintenance. A special tool allows • SEMS screws for wiring of the separate base. maintenance personnel to plug in and remove detectors without • Optional relay, isolator, and sounder bases. using a ladder. Mount base (all base types) on an electrical backbox which is at Specifications least 1.5" (3.81 cm) deep. For a chart of compatible junction boxes, see DN-60054. Sensitivity: 0.5% to 2.35% per foot obscuration NOTE: 1) Because of inherent supervision provided by the SLC Size: 2.1" (5.3 cm) high; base determines diameter. loop, end-of-line resistors are not required. Wiring “T-taps” or – B210LP(A): 6.1" (15.5 cm) diameter. branches are permitted for Style 4 (Class “B”) wiring. 2) When – B501(A): 4.1" (10.4 cm) diameter. using relay or sounder bases, consult the ISO-X(A) installation – B200S(A): 6.875" (17.46 cm) diameter. DN-6935:D • 12/08/2011 — Page 1 of 2 B210-2951.jpg sheet I56-1380 for device limitations between isolator modules ACCESSORIES and isolator bases. F110: Retrofit flange to convert B210LP(A) to match the B710LP(A) profile, or to convert older high-profile bases to low- Agency Listings and Approvals profile. These listings and approvals apply to the modules specified in F110BP: Bulk pack of F110; package contains 15. this document. In some cases, certain modules or applications F210: Replacement flange for B210LP(A) base. may not be listed by certain approval agencies, or listing may be RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Mounts to a in process. Consult factory for latest listing status. U.S. single-gang electrical box. For use with B501(A) and • UL Listed: S1115. B210LP(A) bases only. • ULC Listed: S1115 (FSP-851A, FSP-851RA, FSP-851TA). SMB600: Surface mounting kit • MEA Listed: 225-02-E . M02-04-00:Test magnet. •FM Approved. M02-09-00: Test magnet with telescoping handle. • CSFM: 7272-0028:0206 . XR2B: Detector removal tool. Allows installation and/or removal • Maryland State Fire Marshal: Permit # 2122 . of detector heads from bases in high ceiling applications. • BSMI: CI313066760036. XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524 m) • CCCF: Certif. # 2004081801000017 (FSP-851T) sections. Certif. # 2004081801000016 (FSP-851). T55-127-010: Detector removal tool without pole. • U.S. Coast Guard: 161.002/42/1 (NFS-640); 161.002/50/0 BCK-200B: Black detector covers for use with FSP-851(A) only; (NFS2-640/NFS-320/NFS-320C, excluding B210LP(A)). box of 10. • Lloyd’s Register: 11/600013 (NFS2-640/NFS-320/NFS- WCK-200B: White detector covers for use with FSP-851(A) 320C, excluding B210LP(A)). only; box of 10. Product Line Information NOTE: “A” suffix indicates ULC Listed model. FSP-851: Low-profile intelligent photoelectric sensor. Must be mounted to one of the bases listed below. FSP-851A: Same as FSP-851 but with ULC listing. FSP-851T: Same as FSP-851 but includes a built-in 135°F (57°C) fixed-temperature thermal device. FSP-851TA: Same as FSP-851T but with ULC listing. FSP-851R: Low-profile intelligent photoelectric sensor, remote test capable. For use with DNRA/DNRW. FSP-851RA: Same as FSP-851R but with ULC listing. For use with DNRA. INTELLIGENT BASES NOTE: “A” suffix indicates ULC Listed model. NOTE: For details on intelligent bases, see DN-60054. B210LP(A): Standard U.S. flanged low-profile mounting base. B210LPBP: Bulk pack of B210LP; package contains 10. B501(A): Standard European flangeless mounting base. B501BP: Bulk pack of B501; package contains 10. B200S(A): Intelligent, programmable sounder base capable of producing sound output in high or low volume with ANSI Tempo- ral 3, ANSI Temporal 4, continuous tone, marching tone, and custom tone. B200SR(A): Intelligent sounder base capable of producing sound output with ANSI Temporal 3 or continuous tone. Replaces B501BH series bases in retrofit applications. B224RB(A): Plug-in System Sensor relay base. Screw termi- nals: up to 14 AWG (2.0 mm²). Relay type: Form-C. Rating: 2.0 A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC inductive. -Notifier® and FlashScan® are registered trademarks of Honeywell B224BI(A): Plug-in System Sensor isolator detector base. International Inc. Maximum 25 devices between isolator bases . ©2011 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. Made in the U.S. A. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2 — DN-6935:D • 12/08/2011