CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Chip Type, Ultra-low ESR CK series Ultra-low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). Low ESR CJ CK Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 2.5 to 6.3V Rated Capacitance Range 220 to 2200µF Capacitance Tolerance ±20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C (1) Less than or equal to the specified value 100kHz, 20°C ESR at Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C Temperature Characteristics Z+105°C / Z+20°C 1.25 (100kHz) Z–55°C / Z+20°C 1.25 (Max.Impedance Ratio) Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value Endurance capacitors are restored to 20°C after the rated voltage is ESR(1) 150% or less than the initial specified value applied for 2000 hours at 105°C. Leakage current ( 2) Less than or equal to the initial specified value Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the Damp Heat tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is ESR(1) (Steady State) 150% or less than the initial specified value applied for 1000 hours at 60°C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at Capacitance change Within ± 10% of the initial capacitance value ( 3) right, provided that it's temperature profile is measured at the tan δ 130% or less than the initial specified value capacitor top and the terminal. ESR(1) 130% or less than the initial specified value Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. Leakage current ( 2) Less than or equal to the initial specified value The duration for over +230°C temperature at capacitor surface shall Resistance to not exceed 60 seconds. Soldering Heat In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 6.3V 220µF) Dimensions Positive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Plastic platform Capacitance Lot No. 0.3 MAX. C±0.2 P C K 0 J 2 2 1 M C O 1 G S Taping code Configuration Capacitance toleranc (±20%) +0.1 L Rated capacitance (220μF) -0.4 Voltage ( j:6.3v) Series Negative Rated voltage (6.3V) H Series name Type (mm) Size φ6.3 × 6L φ8 × 7L φ10 × 8L φ10 × 10L φD 6.3 8.0 10.0 10.0 L 5.9 6.9 7.9 9.9 A 7.3 9.0 11.0 11.0 B 6.6 8.3 10.3 10.3 Voltage C 6.6 8.3 10.3 10.3 V 2.5 4 6.3 E 2.1 3.2 4.6 4.6 Code e g j H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. CAT.8100B CK 220 j 941 φD + 0.5 MAX. B±0.2 E 0.5 MAX. A±0.2 CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CKseries Standard Ratings Rated Voltage Surge Voltage Rated Capacitance Case Size Leakage Current ESR (mΩ) Rated Ripple tan δ Part Number (V)(code) (V) (μF) φD × L (mm) (μA) (at 100kHz 20°C) (mArms) 390 6.3 × 6 0.12 293 10 3900 PCK0E391MCO1GS 560 8 × 7 0.12 420 9 4500 PCK0E561MCO1GS 2.5 2.8 680 8 × 7 0.12 510 9 4500 PCK0E681MCO1GS (0E) 1200 10 × 8 0.12 900 9 5000 PCK0E122MCO1GS 2200 10 × 10 0.12 1650 8 6000 PCK0E222MCO1GS 330 6.3 × 6 0.12 396 10 3900 PCK0G331MCO1GS 470 8 × 7 0.12 564 9 4500 PCK0G471MCO1GS 4 560 0.12 672 9 4500 PCK0G561MCO1GS 4.6 8 × 7 (0G) 1000 10 × 8 0.12 1200 9 5000 PCK0G102MCO1GS 1800 10 × 10 0.12 2160 8 6000 PCK0G182MCO1GS 0.12 416 10 3900 PCK0J221MCO1GS 220 6.3 × 6 330 8 × 7 0.12 624 9 4500 PCK0J331MCO1GS 6.3 390 8 × 7 0.12 737 9 4500 PCK0J391MCO1GS 7.2 (0J) 0.12 1550 9 5000 PCK0J821MCO1GS 820 10 × 8 1500 10 × 10 0.12 2835 8 6000 PCK0J152MCO1GS Rated ripple current (mArms) at 105°C 100kHz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100B