D502 D501 NEG POS RSH SIGNAL INPUT 1/20 to 2 HP isolated scr dc chassis, neMa 4X A HP Rating HP Rating Field Input Output Max @ @ Rev- Supply Form Drive Voltage Voltage Current Enclosure Isolation UL CUL CE 90 VDC 180 VDC ersing (VDC) Factor (VAC) (VDC) (ADC) U C U R L US LISTED Output Output **** C R L US LISTED ®® PCM21010A 115 0-90 2 1/20 - 1/8 – Chassis ***** 0-10 VDC – 1.37 YES – YES 115 / 0-90 0-10 VDC / PCM23411A 3 1/20 - 1/8 1/8 - 1/4 NEMA 4X ***** YES 1.37 – – YES 230 / 0-180 4-20 mA PCM21000A 115 0-90 10* 1/4 - 1 – Chassis ***** 0-10 VDC – 1.37 YES – YES PCM22000A 230 0-180 10* – 1/2 - 2 Chassis ***** 0-10 VDC – 1.37 YES – YES 115 / 0-90 0-10 VDC / PCM23001A 10 1/8 - 1 1/4 - 2 Chassis ***** YES 1.37 YES – YES 230 / 0-180 4-20 mA 115 / 0-90 0-10 VDC / PCM23401A 10 1/8 - 1 1/4 - 2 NEMA 4X ***** YES 1.37 YES – YES 230 / 180 4-20 mA * Heatsink number 223-0159 must be used when the output is above 5 Amps. **** The field supply is rated at 1 Amp DC. A 50/100 VDC field is available with 115 VAC input, and a 100/200 VDC field is available with 230 VAC input. ***** See Regenerative drives in Section C for drives that can reverse on-the-fly. PcM23001a diMensions The PCM20000A Series of drives are a cost-effective solution for variable speed, process control applica- 6.90 [175] tions from 1/20 to 2 HP. These are SCR drives that 0.70 [18] integrate isolation allowing them to accept external 6.30 [160] analog process control signals. Alternative solutions require users to wire a separate isolation card to the K A G K A K A K A K A G SCR501 D506 D507 D508 SCR502 drive which adds cost and reduces available space. A2 MOV501 MOV502 C516 T501 L1 L2 115 230 4.40 [112] SW501 C501 Users can operate the drives in manual mode using 3.00 [76] F1 F2 IC502 normal potentiometer operation or in signal mode T502 MOV503 C502 IC501 where drive output is proportional to an external sig- A1 SW502 S1 S2 S3 C518 90 180 nal input. Additionally, the PCM23xx1A has a signal ratio made which allows the potentiometer to scale SIG MAX SIG MIN 1 2 3 4 5 MAX SPD MIN SPD TORQUE IR COMP SO501 the output voltage while the external signal is the main control source. It comes with a quick connec- Height: 2.30 [58] tor for wiring between the three operation modes. All dimensions in inches [millimeters] Dimensions of drives not shown above can be found on pages 54 and 55. See page 50 for an in-depth comparison of the dif- Wiring diagrams of chassis drives can be found on pages 59, 60, and 68. ferent models of drives. featUres • MM Footprint: PCM2x0x0A have a compact industry standard footprint. • Isolated inputs: Accepts floating or grounded speed reference signals of 0-10VDC or 4-20mA. 3% linearity through 50:1 speed range (60:1 for PC- M23001A). 1% linearity through 30:1 speed range. • Speed range and regulation: 1-2% regulation over 50:1 (60:1 for PC- M23001A) speed range. • User adjustable calibration pots: IR compensation, min speed, max speed, PCM21000A PCM21010A PCM23401A current limit, signal max adjust, and signal min (PCM23xxxA only). PCM22000A PCM23411A • Spade and screw terminals: Easy to use spade terminals on chassis; screw terminals on enclosed units. • Additional features: Manual or signal mode jumper select. • Additional features (PCM23xx1A only): Third mode of signal input with ratio output, dual voltage AC input, DC field voltage. PCM23001A 10  • PCM20000A SERIES Call us toll free 1.800.MINARIK or find more information online at www.minarikdrives.com R525 R531