1500W Single Output Power Supply SPV-1500 series Features : Universal AC input/Full range ZVS new technology AC input active surge current limiting Built-in active PFC function,PF>0.95 Protections: Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC ball bearing fan 3 High power density 8.3W/inch Output voltage can be trimmed between 20% ~ 110% rated value Current sharing up to 4500W(2+1) Alarm signal output Built-in 12V/0.1A auxiliary output for remote control Built-in remote ON-OFF control Built-in remote sense function 3 years warranty SPECIFICATION MODEL SPV-1500-12 SPV-1500-24 SPV-1500-48 DC VOLTAGE 12V 24V 48V RATED CURRENT 125A 63A 32A CURRENT RANGE 0 ~ 125A 0 ~ 63A 0 ~ 32A RATED POWER 1500W 1512W 1536W RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 200mVp-p OUTPUT VOLTAGE ADJ. RANGE 5% typical adjustment by VR, 20% ~ 110% (typ.) adjustment by 1~6VDC external control signal VOLTAGE TOLERANCE Note.3 1.0% LINE REGULATION 0.5% LOAD REGULATION 0.5% SETUP, RISE TIME 1500ms, 100ms at full load HOLD UP TIME (Typ.) 10ms at full load 14ms at full load 16ms at full load VOLTAGE RANGE Note.5 90 ~ 264VAC 127 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) 0.95/230VAC 0.98/115VAC at full load INPUT EFFICIENCY (Typ.) 86.5% 90% 90% AC CURRENT (Typ.) 17A/115VAC 8A/230VAC INRUSH CURRENT (Typ.) 30A/115VAC 60A/230VAC LEAKAGE CURRENT <2.0mA / 240VAC 105 ~135% rated output power OVERLOAD Protection type : Constant current limiting, recovers automatically after fault condition is removed 13.8 ~ 16.8V 30 ~ 34.8V 57.6 ~ 67.2V PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover 105 5 (TSW2 ) detect on heatsink of power transistor OVER TEMPERATURE Protection type : Shut down o/p voltage, recovers automatically after temperature goes down 12V@0.1A(Only for Remote ON/OFF control) AUXILIARY POWER(AUX) Please see the Function Manual REMOTE ON/OFF CONTROL FUNCTION Please see the Function Manual ALARM SIGNAL OUTPUT 2.4 ~ 13.2V OUTPUT VOLTAGE TRIM 4.8 ~ 28V 9.6 ~ 56V -20 ~ +70 (Refer to "Derating Curve") WORKING TEMP. 20~90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT 0.05%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS UL60950-1, TUV EN60950-1 approved WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMC (Note 4) EMC EMISSION Compliance to EN55022 (CISPR22), EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A MTBF 109K hrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION 278*127*83.5mm (L*W*H) 3.0Kg; 4pcs/13Kg/1.19CUFT PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) 5. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:SPV-1500-SPEC 2011-12-19 1500W Single Output Power Supply SPV-1500 seri es Mechanical Specification Case No.943A Unit:mm 240 11.2 16 max. 38 8-M4 L=5(Both Sides) 278 11.2 240 OUTPUT +V 4-M4 L=5 -V CN1 CN2 CN3 8 6 4 2 8 6 4 2 6 4 2 7 5 3 1 7 5 3 1 5 3 1 Air flow I/P LED direction SVR 1 2 3 AC Input Terminal Pin No. Assignment Control Pin No. Assignment(CN1,CN2) : HRS DF11-8DP-2DS or equivalent Pin No. Assignment Pin No. Assignment Pin No. Assignment Mating Housing Terminal 1 FG RCG -S 1 5,7 HRS DF11-8DS HRS DF11-**SC 2 AC/N 2 RC2 LS(Current Share) 6 or equivalent or equivalent 3 AC/L PV 8 +S 3 PS 4 RCG: Remote ON/OFF Ground -S: -Remote Sensing RC2: Remote ON/OFF LS: Load Share PV: Output voltage external control +S: +Remote Sensing PS: Reference voltage terminal, PS and PV are connected when shipping Control Pin No. Assignment(CN3) : HRS DF11-6DP-2DS or equivalent Pin No. Assignment Pin No. Assignment Mating Housing Terminal P OK GND AUXG 1 4 HRS DF11-6DS HRS DF11-**SC 2 P OK 5 RC1 or equivalent or equivalent 3 RCG 6 AUX P OK GND: Power OK Ground AUXG: Auxiliary Ground P OK: Power OK Signal RC1: Remote ON/OFF RCG: Remote ON/OFF Ground AUX: Auxiliary Output PFC fosc : 70KHz Block Diagram PWM fosc : 100KHz +S ACTIVE RECTIFIERS RECTIFIERS EMI POWER +V INRUSH I/P & & CURRENT FILTER SWITCHING -V FILTER LIMITING PFC -S PFC O.V.P. CONTROL O.L.P. PWM DETECTION CONTROL O.T.P. CIRCUIT P OK REMOTE RC LOAD CONTROL SHARING LS FAN AUX RECTIFIERS POWER AUX POWER & FILTER (12V/0.1A) File Name:SPV-1500-SPEC 2011-12-19 127 83.5 93 38.1 22.7 17.5 13 10 4 16 1500W Single Output Power Supply SPV-1500 seri es Derating Curve Static Characteristics 100 Others 80 100 60 90 50 12V 80 40 70 20 60 -20 0 10 20 30 40 45 50 60 70 (HORIZONTAL) 90 100 120 140 150 160 180 200 220 240 264 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz Function Manual 1.Remote ON/OFF (1)Remote ON/OFF control becomes available by applying voltage in CN1 & CN2 & CN3 (2)Table 1.1 shows the specification of Remote ON/OFF function (3)Fig.1.2 shows the example to connect Remote ON/OFF control function Table 1.1 Specification of Remote ON/OFF Connection Method Fig. 1.2(A) Fig. 1.2(B) Fig. 1.2(C) Output on SW Open SW Open SW Close SW Logic Output off SW Close SW Close SW Open Fig.1.2 Examples of connecting remote ON/OFF (A)Using external voltage source (B)Using internal 12V auxiliary output AUX AUX 2.2K 2.2K RC1 RC1 5V 150 150 RC2 RC2 12V typ. 12V typ. 620 SW RCG RCG SW AUXG AUXG (C)Using internal 12V auxiliary output AUX 2.2K RC1 150 RC2 12V typ. SW RCG AUXG File Name:SPV-1500-SPEC 2011-12-19 LOAD (%) LOAD (%) 1500W Single Output Power Supply SPV-1500 series 2.Alarm Signal Output POK (1)Alarm signal is sent out through "P OK" & "P OK GND" pins (2)An external voltage source is required for this function. The maximum applied voltage is 50V and the maximum sink current is 10mA R (3)Table 2.1 explains the alarm function built-in the power supply 0.1uF 100K V Function Description Output of alarm(P OK) The signal is "Low" when the power supply is above Low 15% of the rated output voltage-Power OK (0.5V max at 10mA) POK High or open The signal turns to be "High" when the power supply POK GND External voltage and R (External applied voltage is under 15% of the rated output voltage-Power Fail 10mA max.) (The max. sink is 10mA and 50V) Fig. 2.2 Internal circuit of P OK (Open collector method) Table 2.1 Explanation of alarm function 3.External Voltage Control Vout OVP 120%(Typ.) 120 +S 100 100 +V +V LOAD -V 80 80 Non-Linear -V -S 60 60 40 40 PV 1~6V 20 20 -S V V PS 123456 20 40 60 80 100 120 EXTERNAL VOLTAGE (DC) OUTPUT VOLTAGE (%) Note: (1)Reference voltage terminal, PS and PV are connected when shipping (2)+S & +V, -S & -V also need to be connected on CN1 or CN2. 4.Current Sharing No.1(Master) (1)Parallel operation is available by connecting the units shown as below V+ +S (+S,-S and LS are connected mutually in parallel): -S CN1 LS V- (2)The voltage difference among each output should be minimized that less than 2% is required +S -S CN2 LS (3)The total output current must not exceed the value determined by the following equation AC/L AC/N (Output current at parallel operation)=(The rated current per unit) x (Number of unit) x 0.9 (4) In parallel operation 3 units is the maximum, please consult the manufacturer for other applications (5) When remote sensing is used in parallel operation, the sensing wire must be connected only No.2(Slave) to the master unit V+ +S -S CN1 Note : In parallel connection, maybe only one unit (master) operate if the total output load is LS V- +S less than 5% of rated load condition. -S CN2 LS The other PSUs (slaves) may go into standby mode and their output LEDs will not turn on. AC/L AC/N +S +V Load No.3(Slave) -V -S V+ +S -S CN1 LS V- +S -S CN2 LS AC/L AC/N File Name:SPV-1500-SPEC 2011-12-19 OUTPUT VOLTAGE (%) OUTPUT CURRENT (%)