MEAN WELL SDM30-24S12
Datasheet
Extracted Text
30W DC-DC Single Output SD M -30 s e r i e s Features : Wide 2:1 DC input range In/out capacitance1000pF Protections:Short circuit/Over load/Over voltage 1000VDC I/O isolation for D/D Cooling by free air convection Built-in remote ON-OFF control 100% full load burn-in test Fixed switching frequency at 225KHz Lost cost High reliability 1 year warranty SPECIFICATION MODEL SDM30-12S3 SDM30-24S3 SDM30-48S3 SDM30-12S5 SDM30-24S5 SDM30-48S5 DC VOLTAGE 3.3V 5V RATED CURRENT 5A 5A CURRENT RANGE 0 ~ 5A 0 ~ 5A RATED POWER 16.5W 25W OUTPUT RIPPLE & NOISE (max.) Note.2 75mVp-p 75mVp-p VOLTAGE TOLERANCE Note.3 3.0% 2.0% max. LINE REGULATION 1.0% 1.0% LOAD REGULATION 1.0% 1.0% TRIM OUTPUT 13%(Typ.) output voltage 10%(Typ.) output voltage RATED DC INPUT 12S: 12VDC 24S: 24VDC 48S: 48VDC VOLTAGE RANGE 12S: 9.2 ~ 18VDC 24S: 18~ 36VDC 48S: 36~ 72VDC EFFICIENCY (Typ.) 77% 79% 80% 77% 79% 80% INPUT DC CURRENT 12S:3.6A 24S:2A 48S:1A IDLE CURRENT 12S:35mA 24S/48S:30mA Above 105% rated output power OVER LOAD Protection type : Over power limiting, recovers automatically after fault condition is removed 3.8 ~ 4.95V 5.75 ~ 7.5V PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover SHORT CIRCUIT Protection type : Constant current limiting, recovers automatically after fault condition is removed FUNCTION Logic "1" or open: power on Logic "0" short to Vin-: power off ON/OFF CONTROL -25 ~ +85 (Refer to output load derating curve) WORKING TEMP. ENVIRONMENT STORAGE TEMP., HUMIDITY -25 ~ +85 , 0 ~ 95% RH TEMP. COEFFICIENT 0.03%/ (0~50 SAFETY STANDARDS Design refer to UL1950, TUV EN60950 ISOLATION VOLTAGE SAFETY & I/P-O/P:1KVDC ISOLATION RESISTANCE I/P-O/P:100M Ohms/500VDC EMC Compliance to FCC Part15 J EMI CONDUCTION & RADIATION MTBF 322.4K hrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION 50.8*50.8*16mm (2"*2"*0.63") (L*W*H) 0.1Kg; 150pcs/15Kg/0.97CUFT PACKING 1. All parameters NOT specially mentioned are measured at 12,24,48VDC input, rated load and 25 of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Short circuit not more than 60 second. 5. DC source wires 5cm, an input external al capacitor 47 ~ 100uF is required. File Name:SDM30-SPEC 2004-02-26 30W DC-DC Single Output SDM-30 s erie s Features : Wide 2:1 DC input range In/out capacitance1000pF Protections:Short circuit/Over load/Over voltage 1000VDC I/O isolation for D/D Cooling by free air convection Built-in remote ON-OFF control 100% full load burn-in test Fixed switching frequency at 225KHz Lost cost High reliability 1 year warranty SPECIFICATION MODEL SDM30-12S12 SDM30-24S12 SDM30-48S12 SDM30-12S15 SDM30-24S15 SDM30-48S15 DC VOLTAGE 12V 15V RATED CURRENT 2.1A 2.5A 1.7A 2A CURRENT RANGE 0 ~ 2.1A 0 ~ 2.5A 0 ~ 1.7A 0 ~ 2A RATED POWER 25.2W 30W 25.5W 30W OUTPUT RIPPLE & NOISE (max.) Note.2 100mVp-p 100mVp-p VOLTAGE TOLERANCE Note.3 2.0% max. 2.0% max. LINE REGULATION 1.0% 1.0% LOAD REGULATION 1.0% 1.0% TRIM OUTPUT 10%(Typ.) output voltage RATED DC INPUT 12S: 12VDC 24S: 24VDC 48S: 48VDC VOLTAGE RANGE 12S: 9.2 ~ 18VDC 24S: 18~ 36VDC 48S: 36~ 72VDC EFFICIENCY (Typ.) 80% 82% 84% 80% 83% 85% INPUT DC CURRENT 12S:3.6A 24S:2A 48S:1A IDLE CURRENT 12S:35mA 24S/48S:30mA Above 105% rated output power OVER LOAD Protection type : Over power limiting, recovers automatically after fault condition is removed 13.8 ~ 18V 17.25 ~ 22.5V PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover SHORT CIRCUIT Protection type : Constant current limiting, recovers automatically after fault condition is removed FUNCTION Logic "1" or open: power on Logic "0" short to Vin-: power off ON/OFF CONTROL -25 ~ +85 (Refer to output load derating curve) WORKING TEMP. ENVIRONMENT STORAGE TEMP., HUMIDITY -25 ~ +85 , 0 ~ 95% RH TEMP. COEFFICIENT 0.03%/ (0~50 SAFETY STANDARDS Design refer to UL1950, TUV EN60950 ISOLATION VOLTAGE SAFETY & I/P-O/P:1KVDC ISOLATION RESISTANCE I/P-O/P:100M Ohms/500VDC EMC Compliance to FCC Part15 J EMI CONDUCTION & RADIATION MTBF 322.4K hrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION 50.8*50.8*16mm (2"*2"*0.63") (L*W*H) 0.1Kg; 150pcs/15Kg/0.97CUFT PACKING 1. All parameters NOT specially mentioned are measured at 12,24,48VDC input, rated load and 25 of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Short circuit not more than 60 second. 5. DC source wires 5cm, an input external al capacitor 47 ~ 100uF is required. File Name:SDM30-SPEC 2004-02-26 30W DC-DC Single Output S D M-30 se ries Mechanical Specification Case No. SDM-30 Unit:mm 50.8 5.08 5.08 5.08 22.86 16 4 3 2 1 DIA 1mm BOTTOM VIEW 8 5 7 6 10.16 10.16 10.16 10.16 4.8(typ) Pin. No Assignment Pin No. Assignment Pin No. Assignment 1,6 DC OUTPUT +V 4 CONTROL ON/OFF 2,7 DC OUTPUT -V 8 TRIM 3,5 No pin Block Diagram fosc : 225KHz POWER RECTIFIERS +V EMI I/P SWITCH- & FILTER -V ING FILTER DETECTION O.L.P. PWM TRM CIRCUIT CONTROL CTRL O.V.P. Derating Curve External Output Trimming OUTPUT MAY OPTIONALLY BE EXTERNALLY TRIMMED( 10%) A FIXED RESISTER OR AN EXTERNAL TRIMPOT AS SHOWN 1 6 100 +VIN +VOUT For 48Sxx LOAD 10K 80 2 7 VR -VIN -VOUT VR 60 For 24Sxx 4 8 CTRL TRM UP DOWN TRIMPOT 40 For 12Sxx ON/OFF Control Pin 20 CONTROL INPUT.....................................PIN4 CONTROL COMMON................................PIN2 LOGIC COMPATIBILITY......CMOS OR OPEN COLLECTOR TTL -25 0 10 20 30 40 50 60 70 85 CONTROL VOLTAGE AMBIENT TEMPERATURE ( ) ON............+5.5VDC min OR OPEN CIRCUIT OFF......+2.5VDC max. OR SHORT TO PIN2 File Name:SDM30-SPEC 2004-02-26 LOAD (%) 2.54 4 5 . 7 2 50.8
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the SDM30-24S12 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers








What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods