SCP-800-48 - MEAN WELL

Description

Mean Well SCP-800-48 800W+PFC; 48V@16A; Input Voltage: 180-260VAC (291x120x68 mm) Single Output Enclosed Power Supply

Part Number

SCP-800-48

Price

Request Quote

Manufacturer

MEAN WELL

Lead Time

Request Quote

Category

POWER SUPPLY

Specifications

AC CURRENT

5.0A / 230VAC

COOLING

By fan, >20% load or >50°C fan on

CURRENT RANGE

0 ~ 16A

DC VOLTAGE

48V

Dimensions

290 x 120 x 68mm (LxWxH)

EFFICIENCY(Typ.)

89%

EMI CONDUCTION & RADIATION

Compliance to EN55022 (CISPR22) class A

EMS IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, light industry level, criteria A

FREQUENCY RANGE

47 ~ 63Hz

HARMONIC CURRENT

Compliance to EN61000-3-2,3

Humidity

Operating:20 ~ 90% RH non-condensing; Storage:10 ~ 95% RH

INRUSH CURRENT (Max.)

60A / 230VAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, OP/FG:100M Ohms / 500VDC / 25°C / 70% RH

LEAKAGE CURRENT (Max.)

3.5mA / 240VAC

LINE REGULATION

±0.5%

LOAD REGULATION

±0.5%

MTBF

74.9K hrs min. MIL-HDBK-217F(25°C)

Over Temperature Protection

>100°C / measure by heat sink, near transformer; Protection type:Shut down o/p voltage, recovers automatically after temperature goes down

Over Voltage Protection

110 ~ 135% Follow to output set up point; Protection type:Shut down o/p voltage, re-power on to recover

Overload Protection

105~115% rated output power; Protection type:Current limiting, delay shut down o/p voltage, re-power on to recover

Power Factory

>0.98 / 230VAC

POWER GOOD SIGNAL

Open collector of NPN transistor

RATED CURRENT

16A

RATED POWER

768W

RIPPLE & NOISE (max.)

480mVp-p

SAFETY STANDARDS

UL60950, TUV EN60950-1 approved

SETUP, RISE, HOLD UP TIME

800ms, 400ms, 12ms at full load

Temperature

Operating:-20 ~ +65 (Refer to output load derating curve); Storage:-20 ~ +85°C

Temperature Coefficient

±0.04% / °C (0 ~ 50°C)

Vibration

10 ~ 200Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

VOLTAGE ADJ. RANGE

±3.0% Typical adjustment by potentiometer, 20% ~ 100% adjustment by 1 ~ 5VDC external control

VOLTAGE RANGE

180 ~ 260VAC; 260 ~ 370VDC

VOLTAGE TOLERANCE

±1.0%

WITHSTAND VOLTAGE

I/P-O/P:3KVAC; I/P-FG:1.5KVAC; O/P-FG:0.5KVAC

Features

AC input 180~260VAC only
Built in remote sense function
Built-in parallel operation function(N+1)
Built-in power good signal output
Built-in remote ON-OFF control
Can adjust from 20~100% output voltage by external control 1-5V
Forced air cooling by built-in DC fan
PF> 0.98@ 230VAC
Protections: Short circuit / Overload / Over voltage / Over temperature

Datasheet

Mean Well-SCP-800-12-datasheet1-75186199.pdf

335 KiB

Download

Extracted Text

800W Parallel (N+1) With PFC Function SCP-800 s e ri e s Features : AC input 180~260VAC only PF> 0.98@ 230VAC Protections: Short circuit / Overload / Over voltage / Over temperature Built in remote sense function Built-in remote ON-OFF control Built-in power good signal output Built-in parallel operation function(N+1) Can adjust from 20~100% output voltage by external control 1-5V Forced air cooling by built-in DC fan 3 years warranty SPECIFICATION ORDER NO. SCP-800-09 SCP-800-12 SCP-800-15 SCP-800-18 SCP-800-24 SCP-800-36 SCP-800-48 SCP-800-60 SAFETY MODEL NO. 800S-P009 800S-P012 800S-P015 800S-P018 800S-P024 800S-P036 800S-P048 800S-P060 DC VOLTAGE 9V 12V 15V 18V 24V 36V 48V 60V RATED CURRENT 88A 66A 53A 44.4A 33A 22.2A 16A 13A CURRENT RANGE 0 ~ 88A 0 ~ 66A 0 ~ 53A 0 ~ 44.4A 0 ~ 33A 0 ~ 22.2A 0 ~ 16A 0 ~ 13A RATED POWER 792W 792W 795W 799W 792W 799W 768W 780W OUTPUT RIPPLE & NOISE (max.) Note.2 90mVp-p 120mVp-p 150mVp-p 180mVp-p 240mVp-p 360mVp-p 480mVp-p 500mVp-p VOLTAGE ADJ. RANGE 3.0% Typical adjustment by potentiometer 20% ~ 100% adjustment by 1 ~ 5VDC external control VOLTAGE TOLERANCE Note.3 1.5% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% SETUP, RISE, HOLD UP TIME 800ms, 400ms, 12ms at full load VOLTAGE RANGE 180 ~ 260VAC 260 ~ 370VDC see the derating curve FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR >0.98 / 230VAC EFFICIENCY (Typ.) 83% 84% 85% 86% 88% 88% 89% 90% INPUT AC CURRENT 5.0A / 230VAC INRUSH CURRENT (max.) 60A / 230VAC LEAKAGE CURRENT(max.) 3.5mA / 240VAC 105~115% rated output power OVERLOAD Note.4 Protection type : Current limiting, delay shut down o/p voltage, re-power on to recover 110 ~ 135% Follow to output set up point PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover >100 / measure by heat sink, near transformer OVER TEMPERATURE Protection type : Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. -20 ~ +65 (Refer to output load derating curve) 20 ~ 90% RH non-condensing WORKING HUMIDITY STORAGE TEMP., HUMIDITY -20 ~ +85 10 ~ 95% RH ENVIRONMENT TEMP. COEFFICIENT 0.04% / (0 ~ 50 ) 10 ~ 200Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes VIBRATION SAFETY STANDARDS UL60950, TUV EN60950-1 approved WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & I/P-O/P, I/P-FG, OP/FG:100M Ohms / 500VDC / 25 / 70% RH ISOLATION RESISTANCE EMC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) class A (Note. 5) HARMONIC CURRENT Compliance to EN61000-3-2,3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, light industry level, criteria A Open collector of NPN transistor POWER GOOD SIGNAL SPECIAL FUNCTION DC Voltage Adj., remote sensing, remote control, parallel operation(refer to control terminal instruction manual) COOLING By fan, >20% load or >50 fan on OTHERS MTBF 74.9K hrs min. MIL-HDBK-217F(25 ) DIMENSION 290*120*68mm (L*W*H) PACKING 1.9kg; 8pcs / 22kg / CARTON 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Current limiting 3 times(1.5s,3.0s,5.0s)Then intelligent auto recovery before shut down 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name: SCP-800-SPEC 2008-05-06 800W Parallel (N+1) With PFC Function SCP-800 s e ri e s Mechanical Specification Unit:mm 18.5 41 10 190 10 39 30 9.2 11 CN1 #6-32-4 1 2 3 4 5 6 7 8 1 2 3 M3(NUT)X3H-4 LED Vadj POS+ NEG- 120 251 30 9 M3(NUT) 3H-4 AIR FLOW BOTTOM SIDE M6 Terminal Pin No. Assignment Control terminal Pin No. Assignment (CN1) : Dinkle 51HDBC-O8P or equivalent Pin No. Assignment Pin No. Assignment Pin No. Assignment Mating With 1 AC/L 1 VS+ 5 PG 2 AC/N 2 VS- 6 PAR Dinkle 51SDB-O8P 3 FG VCI GND or equivalent 3 7 VCO INH 4 8 Derating Curve Ta=25 800 100 700 80 600 550 60 400 40 450 20 300 -20 -10 10 20 30 40 50 60 70 90 110 150 170 260 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz File Name: SCP-800-SPEC 2008-05-06 LOAD (%) AC INPUT 15 38 OUTPUT POWER (W) DC OUTPUT NEG POS 26.5 68 17 89 14 800W Parallel (N+1) With PFC Function SCP-800 series Control terminal instruction manual LOAD LOAD LOAD LOAD VS+ VS+ VS+ VS+ VS- VS- VS- VS- VCI VCI VCI VCI VCO VCO VCO VCO H:ON PG PG PG PG ON/OFF SWITCH PAR PAR PAR PAR L:OFF GND GND GND GND INH INH INH INH USING INTERNAL VOLTAGE CONTROL ON/OFF CONTROL BY SWITCH ON/OFF CONTROL BY TRANSISTOR REMOTE SENSING Vout O.V.P. 120% (Typ.) GOOD : LED OFF FAIL 120 :LED ON 100 LOAD LOAD 80 Non-Linear VS+ VS+ 60 VS- VS- VCI VCI VCO VCO 40 DC 1-5V PG PG PAR PAR GND GND 20 INH INH 40V / 0.5A MAX. V 123456 POWER GOOD SIGNAL OUTPUT VOLTAGE ADJUST WITH DC 1-5V EXTERNAL VOLTAGE (DC) LOAD LOAD VS+ VS+ VS+ VS+ VS+ VS+ VS- VS- VS- VS- VS- VS- VCI VCI VCI VCI VCI VCI VCO VCO VCO VCO VCO VCO PG PG PG PG PG PG PAR PAR PAR PAR PAR PAR GND GND GND GND GND GND INH INH INH INH INH INH PARALLEL OPERATION WITHOUT REMOTE SENSING PARALLEL OPERATION WITH REMOTE SENSING File Name: SCP-800-SPEC 2008-05-06 OUTPUT VOLTAGE (%)

Frequently asked questions

At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products