MEAN WELL SCP-600-12
Specifications
AC CURRENT
5.0A / 230VAC
Cooling
By fan, >20% load or >50°C fan on
CURRENT RANGE
0 ~ 50A
DC VOLTAGE
12V
Dimensions
290*120*68mm (L*W*H)
EFFICIENCY(Typ.)
84%
EMI Conduction & Radiation
Compliance to EN55022 (CISPR22) class A
EMS Immunity
Compliance to EN61000-4-2,3,4,5,6,8,11, light industry level, criteria A
FREQUENCY RANGE
47 ~ 63Hz
Harmonic Current
Compliance to EN61000-3-2,3
Humidity
Operating:20 ~ 90% RH non-condensing; Storage:10 ~ 95% RH
INRUSH CURRENT (max.)
60A / 230VAC
ISOLATION RESISTANCE
I/P-O/P, I/P-FG, OP/FG:100M Ohms / 500VDC / 25°C / 70% RH
LEAKAGE CURRENT (max.)
3.5mA / 240VAC
LINE REGULATION
±0.5%
LOAD REGULATION
±0.5%
MTBF
74.9K hrs min.; MIL-HDBK-217F(25°C)
Over Temperature Protection
>100°C/measure by heat sink, near transformer; Protection type:Shut down o/p voltage, recovers automatically after temperature goes down
Over Voltage Protection
110 ~ 135% Follow to output set up point; Protection type:Shut down o/p voltage, re-power on to recover
Overload Protection
105 ~ 115% rated output power; Protection type:Current limiting, delay shut down o/p voltage, re-power on to recover
Power Factor
>0.98 / 230VAC
Power Good Signal
Open collector of NPN transistor
RATED CURRENT
50A
RATED POWER
600W
RIPPLE & NOISE (max.)
120mVp-p
Safety Model No.
600S-P012
SAFETY STANDARDS
UL60950, TUV EN60950-1 approved
SETUP, RISE, Hold Up TIME
500ms, 250ms, 16ms at full load
Special Function
DC Voltage Adj., remote sensing, remote control, parallel operation(refer to control terminal instruction manual)
Temperature
Operating:-20 ~ +65°C(Refer to output load derating curve); Storage:-20 ~ +85°C
Temperature Coefficient
±0.04%/°C(0 ~ 50°C)
Vibration
10 ~ 200Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
VOLTAGE ADJ. RANGE
±3.0% Typical adjustment by potentiometer; 20%~100% adjustment by 1~5VDC external control
VOLTAGE RANGE
180 ~ 260VAC; 260 ~ 370VDC see the derating curve
VOLTAGE TOLERANCE
±1.0%
WITHSTAND VOLTAGE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
Datasheet
Extracted Text
500~600W Parallel (N+1) With PFC Function SCP-600 s e ri e s Features : AC input 180~260VAC only PF> 0.98@ 230VAC Protections: Short circuit / Overload / Over voltage / Over temperature Built in remote sense function Built-in remote ON-OFF control Built-in power good signal output Built-in parallel operation function(N+1) Can adjust from 20~100% output voltage by external control 1-5V Forced air cooling by built-in DC fan 3 years warranty SPECIFICATION ORDER NO. SCP-600-05 SCP-600-09 SCP-600-12 SCP-600-15 SCP-600-18 SCP-600-24 SCP-600-36 SCP-600-48 SCP-600-60 SAFETY MODEL NO. 600S-P005 600S-P009 600S-P012 600S-P015 600S-P018 600S-P024 600S-P036 600S-P048 600S-P060 DC VOLTAGE 5V 9V 12V 15V 18V 24V 36V 48V 60V RATED CURRENT 100A 66A 50A 40A 33.3A 25A 16.6A 12A 10A CURRENT RANGE 0 ~ 100A 0 ~ 66A 0 ~ 50A 0 ~ 40A 0 ~ 33.3A 0 ~ 25A 0 ~ 16.6A 0 ~ 12A 0 ~ 10A RATED POWER 500W 594W 600W 600W 599W 600W 597W 576W 600W OUTPUT RIPPLE & NOISE (max.) Note.2 100mVp-p 100mVp-p 120mVp-p 150mVp-p 180mVp-p 240mVp-p 360mVp-p 480mVp-p 500mVp-p VOLTAGE ADJ. RANGE 3.0% Typical adjustment by potentiometer 20%~100% adjustment by 1~5VDC external control VOLTAGE TOLERANCE Note.3 1.5% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% SETUP, RISE, HOLD UP TIME 500ms, 250ms, 16ms at full load VOLTAGE RANGE 180 ~ 260VAC 260 ~ 370VDC see the derating curve FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR >0.98 / 230VAC EFFICIENCY (Typ.) 80% 82% 84% 85% 86% 89% 89% 90% 90% INPUT AC CURRENT 5.0A / 230VAC INRUSH CURRENT (max.) 60A / 230VAC LEAKAGE CURRENT (max.) 3.5mA / 240VAC 105 ~ 115% rated output power OVERLOAD Note. 4 Protection type : Current limiting, delay shut down o/p voltage, re-power on to recover 110 ~ 135% Follow to output set up point PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover >100 / measure by heat sink, near transformer OVER TEMPERATURE Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -20 ~ +65 (Refer to output load derating curve) WORKING TEMP. 20 ~ 90% RH non-condensing WORKING HUMIDITY STORAGE TEMP., HUMIDITY -20 ~ +85 10 ~ 95% RH ENVIRONMENT TEMP. COEFFICIENT 0.04% / (0 ~ 50 ) VIBRATION 10 ~ 200Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950, TUV EN60950-1 approved SAFETY STANDARDS WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, OP/FG:100M Ohms / 500VDC / 25 / 70% RH EMC Compliance to EN55022 (CISPR22) class A EMI CONDUCTION & RADIATION (Note. 5) HARMONIC CURRENT Compliance to EN61000-3-2,3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, light industry level, criteria A POWER GOOD SIGNAL Open collector of NPN transistor DC Voltage Adj., remote sensing, remote control, parallel operation(refer to control terminal instruction manual) SPECIAL FUNCTION COOLING By fan, >20% load or >50 fan on OTHERS MTBF 74.9K hrs min. MIL-HDBK-217F(25 ) DIMENSION 290*120*68mm (L*W*H) PACKING 1.9kg ; 8pcs / 22kg / CARTON 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Current limiting 3 times(1.5s,3.0s,5.0s)Then intelligent auto recovery before shut down 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name: SCP-600-SPEC 2008-05-06 500~600W Parallel (N+1) With PFC Function SCP-600 s e ri e s Mechanical Specification Unit:mm 18.5 41 10 190 10 39 30 9.2 11 CN1 #6-32-4 1 2 3 4 5 6 7 8 1 2 3 M3(NUT)X3H-4 LED Vadj POS+ NEG- 120 251 30 9 M3(NUT) 3H-4 AIR FLOW BOTTOM SIDE M6 Terminal Pin No. Assignment Control terminal Pin No. Assignment (CN1) : Dinkle 51HDBC-O8P or equivalent Pin No. Assignment Pin No. Assignment Pin No. Assignment Mating With 1 AC/L 1 VS+ 5 PG 2 AC/N 2 VS- 6 PAR Dinkle 51SDB-O8P 3 FG VCI GND or equivalent 3 7 VCO INH 4 8 Derating Curve Ta=25 800 100 700 80 600 550 60 400 40 450 20 300 -20 -10 10 20 30 40 50 60 70 90 110 140 260 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz File Name: SCP-600-SPEC 2008-05-06 LOAD (%) AC INPUT 15 38 OUTPUT POWER (W) DC OUTPUT NEG POS 26.5 68 17 89 14 500~600W Parallel (N+1) With PFC Function SCP-600 s e ri e s Control terminal instruction manual LOAD LOAD LOAD LOAD VS+ VS+ VS+ VS+ VS- VS- VS- VS- VCI VCI VCI VCI VCO VCO VCO VCO H:ON PG PG PG PG ON/OFF SWITCH PAR PAR PAR PAR L:OFF GND GND GND GND INH INH INH INH USING INTERNAL VOLTAGE CONTROL ON/OFF CONTROL BY SWITCH ON/OFF CONTROL BY TRANSISTOR REMOTE SENSING Vout O.V.P. 120% (Typ.) GOOD : LED OFF FAIL 120 : LED ON 100 LOAD LOAD 80 Non-Linear VS+ VS+ 60 VS- VS- VCI VCI VCO VCO 40 DC 1-5V PG PG PAR PAR GND GND 20 INH INH 40V / 0.5A MAX. V 1 2 3 4 5 6 POWER GOOD SIGNAL OUTPUT VOLTAGE ADJUST WITH DC 1-5V EXTERNAL VOLTAGE (DC) LOAD LOAD VS+ VS+ VS+ VS+ VS+ VS+ VS- VS- VS- VS- VS- VS- VCI VCI VCI VCI VCI VCI VCO VCO VCO VCO VCO VCO PG PG PG PG PG PG PAR PAR PAR PAR PAR PAR GND GND GND GND GND GND INH INH INH INH INH INH PARALLEL OPERATION WITHOUT REMOTE SENSING PARALLEL OPERATION WITH REMOTE SENSING File Name: SCP-600-SPEC 2008-05-06 OUTPUT VOLTAGE (%)
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the SCP-600-12 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
Mean Well ES18U09-P1J Power Supply 18W; 9.0V@2.00A; 2.1*5.5*11/C+/6F1185 (79x54x33 mm) Wallmount Enc...
Mean Well ES25B48-P1J Power Supply - 25W; 48V@0.52A; 2.1*5.5*11/C+/6F1185 (79 x 54 x 33mm) Desktop E...
Manufacturers






What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods